Fluid Dynamics Commons^™

Exploring Red Palm Oil As A Sustainable Plasticizer For Carbon Black-Filled Ssbr/Br Tire Tread Compounds: A Comparative Evaluation Of Commercial Alternatives, Norma Arisanti Kinasih, Mohamad Irfan Fathurrohman, Santi Puspitasari, Dewi Kusuma Arti, Abdulhakim Masa

Journal of Materials Exploration and Findings

This study investigates the application of red palm oil (RPO) as an alternative vegetable oil resource to substitute petroleum-based plasticizers, which have environmental and health concerns, in carbon black (CB)-filled SSBR/BR tire tread compounds. The plasticizing effects of RPO were thoroughly evaluated by comparing them with a commercial bio-based plasticizer, Epoxidized Soybean Oil (ESBO), and two safer petroleum-based oils, Naphthenic Oil (NYNAS) and Treated Distillate Aromatic Extract (TDAE). The initial investigation shows that fatty acid composition is imposing regarding the plasticizing effect. The higher unsaturated fatty acid content in RPO than in ESBO improved tensile strength and degraded rolling resistance …

Metallurgical Investigation Of A Modified Eye Bolt Failure Caused By Improper Weld Extension, Specification Deviation, And Crevice Corrosion, Dimas Muhammad Fawwaz, Reza Miftahul Ulum, Johny Wahyuadi Soedarsono, Yudha Pratesa

Journal of Materials Exploration and Findings

A modified eye bolt from the David Arm Manhole Storage Tank underwent thorough metallurgical study due to the consequences of the bolt's malfunction during operation. Safety issues arose when the manhole door detached during operation. The mechanical testing and chemical composition analysis of the bolts indicated they were manufactured from an ASTM A193 Grade B7 material used for high-temperature bolting. This material did not conform to the engineering drawing, which mentioned SA 563A, which is about nuts, not bolts. This contradiction clearly shows that the eye bolt which was installed does not conform to the intended design. Welded connections of …

Rejection Of Fe (Iron) And Kmno4 (Organic Substance) Parameters In Peat Water Using Organic Membranes, Muhamad Rafli Sakti Mulia Gonera, Siti Umi Kalsum, Sarah Fiebrina Heraningsih

Journal of Materials Exploration and Findings

Peat water is a surface water source widely used by people in swampy and lowland areas, but it has poor quality characteristics such as high organic matter content, low pH, and dissolved metal levels such as iron that exceed the threshold. These conditions can cause health problems and reduce the quality of clean water so that effective treatment technology is needed. This study aims to analyze the effectiveness of ultrafiltration membranes made from chitosan from shrimp shell waste in rejecting iron (Fe) and organic substances in peat water, and to determine the effect of pressure on separation performance. This study …

Feasibility Analysis Of Thermal Oxidizer To Determine Remaining Life Using Fitness- For-Service Level 3 Method, Yudhi Yudistirawan, Donanta Dhaneswara, Wahyuaji Narottama Putra, Gama Widyaputra, Dewi Kurnia Suci, Agung Putra Mahardhika

Journal of Materials Exploration and Findings

An aged thermal oxidizer (TOX) in the oil and gas industry necessitates a comprehensive evaluation to ensure its continued safe operation. This study presents a Remaining Life Assessment (RLA) and a Fitness for Service (FFS) evaluation for the four main components of the TOX, in accordance with API 510, API 579/ASME FFS-1, and ASME BPVC Section VIII Div-1 standards. The investigation includes the determination of maximum stress and maximum temperature required to assess the operational viability of the reactor. The four components are radiant, convection, transition, and stack sections—were modeled using the finite element method (FEM). Following the geometric modeling, …

Microgravity-Induced Alterations In Left Atrial Hemodynamics And Thrombogenic Risk: Insights From Healthy And Atrial Fibrillation Models, Grace M. Hoeppner

Dissertations, Master's Theses and Master's Reports

Background: Microgravity exposure alters cardiovascular loading, yet its impact on left atrial flow dynamics and thrombotic risk remains poorly understood. This study investigates how spaceflight-relevant microgravity-induced changes in cardiac outflow affect left atrial hemodynamics in healthy individuals and patients with atrial fibrillation.

Methods: Patient-specific left atrial models were generated for three healthy individuals and three AF patients. Computational fluid dynamics (CFD) simulations were performed using each patient’s baseline mitral outflow waveform and two modified waveforms representing short- and long-duration post-flight cardiac loading changes derived from echocardiographic observations. Hemodynamic metrics included left atrial velocity, time averaged wall shear stress, oscillatory shear …

Comparison Of Push-Pull Air Curtain To Overhead Downdraft Systems On Aerosol Containment And Distribution In Controlled Environments, Manal Mutairi

Graduate Theses, Dissertations, and Problem Reports (ETD)

Abstract

Comparison of Push-Pull Air Curtain to Overhead Downdraft Systems on Aerosol Containment and Distribution in Controlled Environments.

This dissertation looks at the ongoing issue of tiny airborne particles created during medical and dental procedures and evaluates ways to reduce the risk of exposure for healthcare workers and patients to these particles. The first study focuses on the size, how long particles stay in the air, and how far they travel from common medical procedures that create aerosols, showing that tiny particles (less than 5 µm) can stay in the air long enough to escape basic droplet controls. As a …

Analysis Of Leakage In Nearshore Pipelines Using Fitness For Service Method To Ensure Mechanical Integrity Based On Api-579 Level 3, Elriandri Elriandri, Dedi Priadi

Journal of Materials Exploration and Findings

The Fitness for Service (FFS) analysis is performed as a quantitative assessment to evaluate the integrity condition of a pipeline. Essentially, FFS assessment helps determine whether equipment components can operate safely despite existing deficiencies. This evaluation is carried out using the Finite Element Method (FEM). In the case of an underwater pipeline that experiences leak due to anchor pull at the flange connection, it undergoes plastic deformation and is lifted approximately 1 meter. As a mitigation step, inspection and repairs have been carried out by the company. Subsequently, modeling is performed to reconstruct the deformation process of the pipeline. Then, …

Assessment Of The Melt Quality Of A 30% Scrap Adc12 Aluminium Alloy Using The Inclusion And Fluidity Measurement Instrument (Ifmi) With Mullite Ceramic Filters, Gusti Ruri Ruri Lestari, Sandya Ananda Riswan, Muhammad Anis, Ahmad Ashari, Paramita Vidya Ayuningtyas, Bambang Suharno Prof, Donanta Dhaneswara

Journal of Materials Exploration and Findings

The increasing demand for sustainable practices in the metal casting industry has driven the use of recycled aluminum alloys such as ADC12. However, the addition of aluminum scrap tends to increase oxide inclusions, which reduce melt fluidity and compromise casting quality. This study utilizes the Inclusion and Fluidity Measurement Instrument (IFMI), equipped with mullite ceramic filters, to assess the melt quality of ADC12 aluminum alloy containing 30% scrap. Fluidity and inclusion characteristics were evaluated at five pouring temperatures (660°C, 680°C, 700°C, 720°C, and 740°C). The results show that fluidity increased with temperature, reaching a peak of 84.6 g·s⁻¹ at 740°C, …

Equipment Criticality Analysis To Determine Asset Integrity Management System Scheme In Supporting Production Optimization Scenarios In The Aeging Field, Donny Andryanto, Donanta Dhaneswara

Journal of Materials Exploration and Findings

This research investigates the production decline and cost increase in the X&Y oil and gas fields from 2022 to 2023. Production fell by 34%, while production costs per barrel rose by 79%. To address these issues, a series of optimization processes are proposed. These aim to restructure and enhance the production facilities to reduce current production costs. The optimizations include reducing pressure at the PPP Platform in 2024. Additional steps include shutting down CPP-ORF 14” pipelines and most processes at CPP 2 Platform by 2027 to convert it into an accommodation platform. Further, the plan involves optimizing the release of …

Morphological Test Of Areca Nut Fiber Ceramic Membrane Using Scanning Electron Microscopy Energy Dispersive X-Ray Mapping Spectroscopy, Amelia Marzain, Siti Umi Kalsum, Marhadi Marhadi, Ahmad Nabil Shahab

Journal of Materials Exploration and Findings

This study investigates the potential of ceramic membranes derived from areca nut fiber as a cost-effective and environmentally sustainable material for the removal of iron (Fe) and manganese (Mn) from groundwater. Two types of membranes were fabricated: one without activation and one chemically activated using 10% sodium hydroxide (NaOH). The morphological and elemental characteristics of both membranes were analyzed using Scanning Electron Microscopy (SEM) and Energy Dispersive X-ray (EDX) mapping. The concentrations of Fe and Mn before and after treatment were measured using Atomic Absorption Spectroscopy (AAS). The NaOH-activated membrane exhibited a more porous surface structure and higher oxygen content, …

Unsaturated Fatty Acid Oil-Based Microdroplets: A Promising Novel Class Of Microdroplets, Ramiz S. Alejilat

Seton Hall University Dissertations and Theses (ETDs)

Droplet-based microfluidics has rapidly advanced numerous fields, including chemistry, biology, materials science, medicine, food science, and cosmetics. In these systems, fluorocarbon oil combined with fluorinated surfactants is the preferred medium for fluid encapsulation, offering exceptional stability and biocompatibility essential for sensitive biological and chemical processes. However, growing concerns about the environmental and biological risks associated with fluorinated chemicals have prompted a search for alternatives.

This study is the first to explore the use of unsaturated fatty acids derived from emu oil for microdroplet formation. We characterized droplet formation based on flow rates and the presence non-fluorinated surfactant at a certain …

A Study Of Wear Measurement And Life Prediction Of Insert Chute Liner On Gold Ore Processing, Ferry Ardika Natanael, Nony Maulidya, Dedi Priadi

Journal of Materials Exploration and Findings

Chutes are critical materials handling assets to transport solid particles from one process step to another in mineral processing, coal mining and cement industries. The material transport, because of material characteristics, cause severe wear on internal lining of chutes or bins’ structure. The wear problem on internal lining of bins or chutes needs to be checked to keep production efficiency. Therefore, not checked wear rate causes liner replacement schedule becomes unpredictable. It leads to production loss and highly cost maintenance in industry. This study shows that condition-based maintenance through regular thickness measurement using Ultrasonic Transducer (UT) to predict life service …

Techno-Enviro-Economic Approach For Electrification Of Rural And Shrimp Farming Regional Development Of An Isolated Island In Indonesia By Utilizing Hybrid Renewable Energy Systems, Fiqih Akbar Wijaya, Mohammad Akita Indianto

Journal of Materials Exploration and Findings

One of the challenges in developing and archipelagic countries such as Indonesia is maintaining energy demand in rural and isolated areas due to difficulties in electrical distribution. For instance, in areas like Bawean Island, no additional electricity capacity has been introduced in the past year, leading to an unmet potential customer demand. One of the possible options is by utilizing Hybrid Renewable Energy Systems (HRES) that are integrated with existing fossil fuel-based energy systems to support the growing energy demand in the remote island. A case study in Bawean Island is conducted with the projected energy demand covers the energy …

Remaining Life Assessment And Fitness For Service Evaluation Of Aging Chemical Reactors In Polyethylene Terephthalate Resin Industry, Aditya Pahlawan Munthe, Donanta Dhaneswara, Wahyuaji Narottama Putra, Gama Widyaputra

Journal of Materials Exploration and Findings

Aging chemical reactors in the polyethylene terephthalate (PET) resin industry require comprehensive evaluation to ensure safe continued operation. This study conducts a remaining life assessment (RLA) and fitness-for-service (FFS) evaluation on five 30-year-old reactors, based on API 510, API 579/ASME FFS-1, and ASME BPVC Section VIII Div. 1 standards. The analysis involves corrosion rate measurement, future corrosion allowance (FCA) projection, and minimum thickness verification. Among the reactors, R-120 was found to have the shortest remaining life less than 15 years. FFS assessments using three criteria Average Measured Thickness, MAWP from Point Thickness Readings, and Minimum Measured Thickness confirm that R-120 …

Analysis Of Leak Testing Planning For Carbon Dioxide Piping Systems In The Development Of Carbon Capture, Utilization, And Storage Facilities In The Bintuni Basin, Devi Sentiani, Akhmad Herman Yuwono Professor

Journal of Materials Exploration and Findings

Carbon Capture, Utilization, and Storage (CCUS) technologies have become a key strategic response to global efforts to reduce CO₂ emissions. This study presents a leak testing strategy designed for a carbon dioxide (CO₂) piping system as part of a Carbon Capture, Utilization, and Storage (CCUS) project in the Bintuni Basin, West Papua, Indonesia. This study aims to ensure the system is properly prepared before commissioning by designing a leak test plan that is both practical and technical, based on ASME B31.3, ASME PCC-2, and API STD 520 Part 1. We conducted the process, which involves identifying the system boundaries, …

Assessment Of H2s-Induced Cracking Susceptibility In Steam Line Pipes And Weld Zones During Geothermal Well Construction, Riene Kaelamanda Pragitta, Yudha Pratesa

Journal of Materials Exploration and Findings

The susceptibility of steam line pipes, especially in the HAZ (heat-affected zone) and weldment areas, to hydrogen sulfide in the geothermal industry is crucial to understand from the early stages, particularly during construction. The combination of tensile stress from residual stresses after welding and metallurgical phase transformation makes the joint areas vulnerable to sulfide stress cracking. This condition becomes even more extreme when the equipment operates during the well stimulation phase. This research assesses the severity of H₂S-induced cracking using NACE MR0175 and ISO 15156-1 standards, focusing on the effects of pH and partial pressure of H₂S (p_{H₂S …}

Combined Risk Based Inspection And Fault Tree Analysis For Repetitive 3-Phase Line Piping Leakage At West Java Offshore Topside Facility, Dona Yuliati, Akhmad Herman Yuwono, D. Rizal Asral, Donanta Dhaneswara

Journal of Materials Exploration and Findings

Hydrocarbon releases might result in serious consequences in various aspects. In addition to the contribution to environmental pollution, repetitive leakages need high repair costs. This study aim is to minimize potential repetitive leakage for other typical 3-phase piping systems. We conducted the risk assessment by adopting Risk Based Inspection (RBI) API 581 to identify risk level, calculating piping lifetime, recommended inspection plan and mitigations. The most relevant root causes can be obtained through quantitative Fault Tree Analysis (FTA). Observation and investigation was taken from eight 3-phase piping systems that experienced repetitive leakages. It has been found that the risk level …

Nitrogen Gas Quenching Pressure Effect On Bs S155 Alloy Steel In Vacuum Furnace, Agus Mulyadi Hasanudin, Eddy Sumarno Siradj

Journal of Materials Exploration and Findings

The production of metal and alloy products requires the use of heat treatment, when during the heat treatment process, quenching is a crucial step. The quenching medium can be anything from water, a salt bath, oil, air and gas. In a vacuum furnace, pressurized gas, most frequently nitrogen (N₂) gas, serves as one of the quenching mediums. One of the drawbacks of the quenching process is the distortion and dimensional change of the parts. This paper aims to investigate the influence of nitrogen gas quenching pressure on the distortion and dimensional change of aerospace actuator gear planet parts …

Sexual Dimorphism Of Glomerular Capillary Morphology In Rats, Zackarias Coker

Undergraduate Honors Theses

Chronic kidney disease (CKD) progresses faster in males than females; however, the underlying mechanisms remain poorly understood. Sex differences in glomerular capillary morphology has been hypothesized to contribute, in part, to the increased susceptibility to hypertension-induced renal injury and CKD progression in males, but this has not been investigated. The goal of the present study was to assess glomerular capillary morphology in male vs. female rats with intact kidneys and after uninephrectomy (UNX). We hypothesized that glomerular capillary radii (R_CAP) and length (L_CAP) would be greater in male rats.

Male (n=4) and female (n=4) with intact …

Hydrodynamic Characterization Of Laboratory And Production Equipment For Pharmaceutical Testing And Manufacturing Using Experimental And Computational Approaches, Chadakarn Sirasitthichoke

Dissertations

The hydrodynamics of process units used in pharmaceutical industry, i.e., the distribution of velocity profiles and shear stresses within the vessel, often controls the process performance, significantly affecting product quality. The hydrodynamics is strongly influenced by several factors such as the vessel shape, stirrer type, presence of internals and baffles, agitation intensity, and liquid properties. Most of these parameters can be varied by the process designers and the operators to achieve the desired process outcomes. The impact of the hydrodynamics on the process outcome can be profound in both large vessels (e.g., reactors) and smaller vessels (e.g., dissolution vessels), involving …

Design And Control Of A Peristaltic Pump To Simulate Left Atrial Pressure In A Conductive Silicone Model, Jeremy Collins

Mechanical Engineering Undergraduate Honors Theses

According to the CDC, atrial fibrillation is responsible for more than 454,000 hospitalizations and approximately 158,000 deaths per year. A common treatment for atrial fibrillation is catheter ablation, a process in which a long flexible tube is guided through the femoral artery and to the source of arrhythmia in the heart, where it measures the electrical potential at various locations and converts problematic heart tissue to scar tissue via ablation. This paper details the design and control of a low-cost ($400) peristaltic pump system using repetitive control to replicate blood pressure in the left atrium in a conductive silicone model …

Nebulizer-Based Systems To Improve Pharmaceutical Aerosol Delivery To The Lungs, Benjamin M. Spence

Theses and Dissertations

Combining vibrating mesh nebulizers with additional new technologies leads to substantial improvements in pharmaceutical aerosol delivery to the lungs across therapeutic administration methods. In this dissertation, streamlined components, aerosol administration synchronization, and/or Excipient Enhanced Growth (EEG) technologies were utilized to develop and test several novel devices and aerosol delivery systems. The first focus of this work was to improve the poor delivery efficiency, e.g., 3.6% of nominal dose (Dugernier et al. 2017), of aerosolized medication administration to adult human subjects concurrent with high flow nasal cannula (HFNC) therapy, a form of continuous-flow non-invasive ventilation (NIV). The developed Low-Volume Mixer-Heater (LVMH) …

Understanding Of Aerosol Transmission Of Covid 19 In Indoor Environments, Adama Barro, Cathal O'Toole, Jacob S. Lopez, Matthew Quinones, Sherene Moore

Publications and Research

Our reason for discussing severe acute respiratory syndrome corona virus 2 (SARS-CoV-2) or 2019 novel corona virus (Covid-19), is to understand its aerosol transmission characteristics in indoor spaces and to mitigate further spread of this disease by designing a new HVAC system. The problem that we are tackling is the spread of covid-19 droplets through aerosol transmission by looking at potential engineering solutions to the existing HVAC systems. The purpose is to eradicate the spread of the COVID-19 by testing indoor spaces in an effort to understand the effectiveness of ventilation controls. We believe that scientists and engineers have not …

Parameter Identifiability And Estimation In A 1d Cardiovascular Fluid Dynamics Model, Mitchel J. Colebank

Biology and Medicine Through Mathematics Conference

No abstract provided.

Parameter Estimation For Tear Film Thinning, Rayanne Luke

Biology and Medicine Through Mathematics Conference

No abstract provided.

Quantification Of Contrast-Enhanced Ultrasound, Joseph Pathoulas

All College Thesis Program, 2016-2019

The aim of this experiment was to investigate the effect of manipulating ultrasound scanner settings on time-intensity curve parameters in a tube perfusion phantom system using contrast-enhanced ultrasound imaging. Imaging was performed using a Philips LOGIQ E9 ultrasound scanner equipped with a C1-6VN transducer and utilized two different microbubble contrast agents: Definity and Lumason. The ultrasound scanner settings manipulated included: gain, dynamic range, and frequency. Additionally, relative microbubble concentration, microbubble type, and perfusion flow rate were manipulated. Four time-intensity curve parameters (time to peak, area under curve, gradient, peak intensity) were measured from linearized pixel data. Time to peak was …

Giardia Lamblia Growth In Viscoelastic Fluids, Kelly Watanabe

CMC Senior Theses

Giardia lamblia is a single-celled protozoan parasite that when ingested, causes diarrheal disease and infects 33% of people in developing countries. Previous studies observe Giardia in water-like fluids, but Giardia's infectious environment consists of viscoelastic mucus in the small intestine. Therefore, Giardia was cultured in viscoelastic fluids, and its population growth was observed in vitro. To create shear-thinning viscoelastic fluids, 0.2% and 0.4% long-chain polyacrylamide (LCPAM) was added to cell culture media. Giardia was cultured in control media, 0.2% LCPAM, and 0.4% LCPAM, and population growth was quantitatively determined over time. Increasing LCPAM concentration resulted in a solution with …

Patient-Specific Multiscale Computational Fluid Dynamics Assessment Of Embolization Rates In The Hybrid Norwood: Effects Of Size And Placement Of The Reverse Blalock–Taussig Shunt, Ray Prather, John Seligson, Marcus Ni, Eduardo Divo, Alain J. Kassab, William Decampli

Publications

The hybrid Norwood operation is performed to treat hypoplastic left heart syndrome. Distal arch obstruction may compromise flow to the brain. In a variant of this procedure, a synthetic graft (reverse Blalock–Taussig shunt) is placed between the pulmonary trunk and innominate artery to improve upper torso blood flow. Thrombi originating in the graft may embolize to the brain. In this study, we used computational fluid dynamics and particle tracking to investigate the patterns of particle embolization as a function of the anatomic position of the reverse Blalock–Taussig shunt. The degree of distal arch obstruction and position of particle origin influence …

A Mathematical Analysis Of Drug Dissolution In The Usp Flow Through Apparatus, David Mcdonnell, Deirdre M. D'Arcy, Lawrence J. Crane, Brendan Redmond

Articles

This paper applies boundary layer theory to the process of drug dissolution in the USP (United States Pharmacopeia) Flow Through Apparatus. The mass transfer rate from the vertical planar surface of a compact within the device is examined. The theoretical results obtained are then compared with those of experiment. The paper also examines the effect on the dissolution process caused by the interaction between natural and forced convection within the apparatus and the introduction of additional boundaries.

Plasma Processes And Polymers Third Special Issue On Plasma And Cancer, Mounir Laroussi, Annemie Bogaerts, Nazir Barekzi

Electrical & Computer Engineering Faculty Publications

(First paragraph) This issue of Plasma Processes and Polymers is the third in a series on the applications of low temperature plasma (LTP) against cancer, or “plasma oncology.” The papers in this issue are inspired from the talks given at the third International Workshop on Plasma for Cancer Treatment (IWPCT) which took place on April 11–12, 2016 in Washington, DC, USA. IWPCT is an international workshop that was created in 2014 as a venue to share cutting edge plasma oncology research. The first IWPCT was held in Washington DC, under the co-chairmanship of Prof. Mounir Laroussi (Old Dominion University) and …