Fluid Dynamics Commons^™

Exploring Red Palm Oil As A Sustainable Plasticizer For Carbon Black-Filled Ssbr/Br Tire Tread Compounds: A Comparative Evaluation Of Commercial Alternatives, Norma Arisanti Kinasih, Mohamad Irfan Fathurrohman, Santi Puspitasari, Dewi Kusuma Arti, Abdulhakim Masa

Journal of Materials Exploration and Findings

This study investigates the application of red palm oil (RPO) as an alternative vegetable oil resource to substitute petroleum-based plasticizers, which have environmental and health concerns, in carbon black (CB)-filled SSBR/BR tire tread compounds. The plasticizing effects of RPO were thoroughly evaluated by comparing them with a commercial bio-based plasticizer, Epoxidized Soybean Oil (ESBO), and two safer petroleum-based oils, Naphthenic Oil (NYNAS) and Treated Distillate Aromatic Extract (TDAE). The initial investigation shows that fatty acid composition is imposing regarding the plasticizing effect. The higher unsaturated fatty acid content in RPO than in ESBO improved tensile strength and degraded rolling resistance …

Metallurgical Investigation Of A Modified Eye Bolt Failure Caused By Improper Weld Extension, Specification Deviation, And Crevice Corrosion, Dimas Muhammad Fawwaz, Reza Miftahul Ulum, Johny Wahyuadi Soedarsono, Yudha Pratesa

Journal of Materials Exploration and Findings

A modified eye bolt from the David Arm Manhole Storage Tank underwent thorough metallurgical study due to the consequences of the bolt's malfunction during operation. Safety issues arose when the manhole door detached during operation. The mechanical testing and chemical composition analysis of the bolts indicated they were manufactured from an ASTM A193 Grade B7 material used for high-temperature bolting. This material did not conform to the engineering drawing, which mentioned SA 563A, which is about nuts, not bolts. This contradiction clearly shows that the eye bolt which was installed does not conform to the intended design. Welded connections of …

Rejection Of Fe (Iron) And Kmno4 (Organic Substance) Parameters In Peat Water Using Organic Membranes, Muhamad Rafli Sakti Mulia Gonera, Siti Umi Kalsum, Sarah Fiebrina Heraningsih

Journal of Materials Exploration and Findings

Peat water is a surface water source widely used by people in swampy and lowland areas, but it has poor quality characteristics such as high organic matter content, low pH, and dissolved metal levels such as iron that exceed the threshold. These conditions can cause health problems and reduce the quality of clean water so that effective treatment technology is needed. This study aims to analyze the effectiveness of ultrafiltration membranes made from chitosan from shrimp shell waste in rejecting iron (Fe) and organic substances in peat water, and to determine the effect of pressure on separation performance. This study …

Global Time-Resolved Measurements Of Inlet/Isolator Unstart Induced By Mass Injection, Andrew N. Bustard, Benjamin L. Bemis, Aaron Marques, Matthew J. Zahr, Thomas J. Juliano

Publications

The inner surface pressure of an axisymmetric inlet/isolator model was measured using anodized-aluminum pressure-sensitive paint (PSP) viewing through cast acrylic. Temperaturesensitive paint was utilized to correct for the PSP’s temperature sensitivity. The model was tested under Mach 5.7 flow at 𝑹𝒆 = 7.1 ×106 /m under conventional noise conditions. Transverse jet injection with jet-to-inlet mass-flow ratios up to 0.8 was used to induce unstart in the inlet/isolator. Background-oriented schlieren visualization of the inlet shocks was collected simultaneously with the PSP to determine when the inlet unstarted. Computational fluid dynamics results were used to determine off-wall flow structures and quantify approach …

An Analytical Framework For Quantifying Urban And Community Resilience To Natural Hazards From Cell-Phone Gps-Location And Traffic-Flow Data, Georgios Chatzikyriakidis

Civil and Environmental Engineering Theses and Dissertations

Urban areas are increasingly exposed to natural hazards while accommodating a growing share of the global population, yet a consistent science-based framework for quantifying urban and community resilience remains lacking. This dissertation develops a physics-based analytical framework grounded in statistical mechanics and the quantitative theory of Brownian motion. A city is conceptualized as a complex medium in which citizens move analogously to Brownian particles within a viscoelastic environment, influenced by socioeconomic interactions and infrastructure functionality.

A central premise is that urban resilience, interpreted as engineering resilience (an outcome), can be quantified through a single metric: the mean-square displacement MSD=⟨r²(t)⟩, of …

Feasibility Analysis Of Thermal Oxidizer To Determine Remaining Life Using Fitness- For-Service Level 3 Method, Yudhi Yudistirawan, Donanta Dhaneswara, Wahyuaji Narottama Putra, Gama Widyaputra, Dewi Kurnia Suci, Agung Putra Mahardhika

Journal of Materials Exploration and Findings

An aged thermal oxidizer (TOX) in the oil and gas industry necessitates a comprehensive evaluation to ensure its continued safe operation. This study presents a Remaining Life Assessment (RLA) and a Fitness for Service (FFS) evaluation for the four main components of the TOX, in accordance with API 510, API 579/ASME FFS-1, and ASME BPVC Section VIII Div-1 standards. The investigation includes the determination of maximum stress and maximum temperature required to assess the operational viability of the reactor. The four components are radiant, convection, transition, and stack sections—were modeled using the finite element method (FEM). Following the geometric modeling, …

Numerical Study Of Nutrient Mixing In Trabecular Bone In Microgravity, Disuse And Normogravity, Sagar Gharti

Doctoral Dissertations and Master's Theses

Mechanical loading is known to regulate bone remodeling by driving interstitial fluid flow which stimulates cells and drives nutrient transport within the trabecular network. In microgravity, the absence of mechanical stimulation or loading suppresses convective flow processes, causing diffusion-driven nutrient mixing and renewal, and accelerated bone loss. This thesis investigates how oscillation frequency and trabecular bone density jointly control nutrient mixing and wall shear stress within trabecular cavities.

A computational fluid dynamics (CFD) framework is developed in STAR-CCM+ using a soft-cap oscillation model that mimics cyclic compression. Three idealized trabecular morphologies are simulated across different frequencies to represent microgravity or …

Microgravity-Induced Alterations In Left Atrial Hemodynamics And Thrombogenic Risk: Insights From Healthy And Atrial Fibrillation Models, Grace M. Hoeppner

Dissertations, Master's Theses and Master's Reports

Background: Microgravity exposure alters cardiovascular loading, yet its impact on left atrial flow dynamics and thrombotic risk remains poorly understood. This study investigates how spaceflight-relevant microgravity-induced changes in cardiac outflow affect left atrial hemodynamics in healthy individuals and patients with atrial fibrillation.

Methods: Patient-specific left atrial models were generated for three healthy individuals and three AF patients. Computational fluid dynamics (CFD) simulations were performed using each patient’s baseline mitral outflow waveform and two modified waveforms representing short- and long-duration post-flight cardiac loading changes derived from echocardiographic observations. Hemodynamic metrics included left atrial velocity, time averaged wall shear stress, oscillatory shear …

Computational Study Of Rotating Detonation Combustors, Aditya Balasubramaniam

Mechanical and Aerospace Engineering Theses

Rotating detonation combustors (RDCs) are pressure-gain combustion devices that sustain one or more continuously rotating detonation waves, offering potential thermodynamic and performance advantages over conventional deflagration-based systems. Their behavior depends strongly on combustor geometry and operating conditions. Understanding these effects is therefore essential for the design and optimization of practical RDCs. Accordingly, this thesis numerically investigates annular RDCs with two primary objectives: (1) to evaluate the effects of propellant mass flux and (2) to assess the influence of annular width on detonation-wave dynamics and combustor performance.

A finite-volume framework is used to solve the compressible reactive Euler equations with hydrogen–air …

Analytical Study Of Transient Mixed Convective Radiative Jeffrey Fluid Flow With Diffusion–Thermo And Chemical Reaction, V. Sathiya, R. Vijayaragavan, B. Rushi Kumar

Mansoura Engineering Journal

This research examines the behavior of unsteady mixed convective radiative Jeffrey fluid flow over a permeable moving plate with a diffusion thermo effect. The study incorporates multiple factors, including aligned magnetic fields, heat generation, radiation, and chemical reactions. The behavior of Jeffrey fluid under these combined conditions is particularly relevant to the design of efficient heat exchangers, MHD generators, and cooling systems for electronic components. A regular perturbation technique was employed to solve the governing equations, yielding distributions for velocity, temperature, and species concentration. These solutions enabled the derivation of expressions for skin friction, Nusselt number, and Sherwood number. Through …

Stability Analysis Of Thermohaline Convection With A Time-Varying Shear Flow Using The Lyapunov Method, Kalin Kochnev

Honors Scholar Theses

This work applies the Lyapunov method to identify instabilities and compute the growth rate of a linear time-varying system. The linear system studied describes cold fresh water on top of hot salty water with a periodically time-varying background shear flow. A time-dependent weighting matrix is employed to construct a Lyapunov function candidate. The resulting linear matrix inequalities are discretized in time using the forward Euler method. As the number of temporal discretization points increases, the growth rate predicted by the Lyapunov method or Floquet theory, used for comparison, will converge to the same value obtained from numerical simulations. Furthermore, the …

Analysis Of Leakage In Nearshore Pipelines Using Fitness For Service Method To Ensure Mechanical Integrity Based On Api-579 Level 3, Elriandri Elriandri, Dedi Priadi

Journal of Materials Exploration and Findings

The Fitness for Service (FFS) analysis is performed as a quantitative assessment to evaluate the integrity condition of a pipeline. Essentially, FFS assessment helps determine whether equipment components can operate safely despite existing deficiencies. This evaluation is carried out using the Finite Element Method (FEM). In the case of an underwater pipeline that experiences leak due to anchor pull at the flange connection, it undergoes plastic deformation and is lifted approximately 1 meter. As a mitigation step, inspection and repairs have been carried out by the company. Subsequently, modeling is performed to reconstruct the deformation process of the pipeline. Then, …

Assessment Of The Melt Quality Of A 30% Scrap Adc12 Aluminium Alloy Using The Inclusion And Fluidity Measurement Instrument (Ifmi) With Mullite Ceramic Filters, Gusti Ruri Ruri Lestari, Sandya Ananda Riswan, Muhammad Anis, Ahmad Ashari, Paramita Vidya Ayuningtyas, Bambang Suharno Prof, Donanta Dhaneswara

Journal of Materials Exploration and Findings

The increasing demand for sustainable practices in the metal casting industry has driven the use of recycled aluminum alloys such as ADC12. However, the addition of aluminum scrap tends to increase oxide inclusions, which reduce melt fluidity and compromise casting quality. This study utilizes the Inclusion and Fluidity Measurement Instrument (IFMI), equipped with mullite ceramic filters, to assess the melt quality of ADC12 aluminum alloy containing 30% scrap. Fluidity and inclusion characteristics were evaluated at five pouring temperatures (660°C, 680°C, 700°C, 720°C, and 740°C). The results show that fluidity increased with temperature, reaching a peak of 84.6 g·s⁻¹ at 740°C, …

Equipment Criticality Analysis To Determine Asset Integrity Management System Scheme In Supporting Production Optimization Scenarios In The Aeging Field, Donny Andryanto, Donanta Dhaneswara

Journal of Materials Exploration and Findings

This research investigates the production decline and cost increase in the X&Y oil and gas fields from 2022 to 2023. Production fell by 34%, while production costs per barrel rose by 79%. To address these issues, a series of optimization processes are proposed. These aim to restructure and enhance the production facilities to reduce current production costs. The optimizations include reducing pressure at the PPP Platform in 2024. Additional steps include shutting down CPP-ORF 14” pipelines and most processes at CPP 2 Platform by 2027 to convert it into an accommodation platform. Further, the plan involves optimizing the release of …

Morphological Test Of Areca Nut Fiber Ceramic Membrane Using Scanning Electron Microscopy Energy Dispersive X-Ray Mapping Spectroscopy, Amelia Marzain, Siti Umi Kalsum, Marhadi Marhadi, Ahmad Nabil Shahab

Journal of Materials Exploration and Findings

This study investigates the potential of ceramic membranes derived from areca nut fiber as a cost-effective and environmentally sustainable material for the removal of iron (Fe) and manganese (Mn) from groundwater. Two types of membranes were fabricated: one without activation and one chemically activated using 10% sodium hydroxide (NaOH). The morphological and elemental characteristics of both membranes were analyzed using Scanning Electron Microscopy (SEM) and Energy Dispersive X-ray (EDX) mapping. The concentrations of Fe and Mn before and after treatment were measured using Atomic Absorption Spectroscopy (AAS). The NaOH-activated membrane exhibited a more porous surface structure and higher oxygen content, …

The Role Of Atmospheric Turbulence On Cloud Droplet Distribution And Droplet Impaction On An Airfoil, Arash Shad, Hashnayne Ahmed, ‪Nadim Zgheib, S. Balachandar, S. A. Sherif

Mechanical Engineering Faculty Publications

We conduct turbulence-informed Euler–Lagrange simulations of droplet-laden flow to examine the effects of atmospheric turbulence on droplet impingement characteristics on a NACA 0012 airfoil. We implement statistical overloading, whereby we inject millions of droplets, ranging in diameter from 1 to 160 microns, upstream of the airfoil at an average streamwise velocity of 120 m/s. Within a fraction of a second, these droplets would have either impinged on the airfoil or continued downstream. While the incoming air flow is maintained uniform, droplet injection is informed by ambient turbulence, affecting both the droplet velocity distribution as well as the size-dependent preferential concentration …

A Study Of Wear Measurement And Life Prediction Of Insert Chute Liner On Gold Ore Processing, Ferry Ardika Natanael, Nony Maulidya, Dedi Priadi

Journal of Materials Exploration and Findings

Chutes are critical materials handling assets to transport solid particles from one process step to another in mineral processing, coal mining and cement industries. The material transport, because of material characteristics, cause severe wear on internal lining of chutes or bins’ structure. The wear problem on internal lining of bins or chutes needs to be checked to keep production efficiency. Therefore, not checked wear rate causes liner replacement schedule becomes unpredictable. It leads to production loss and highly cost maintenance in industry. This study shows that condition-based maintenance through regular thickness measurement using Ultrasonic Transducer (UT) to predict life service …

Techno-Enviro-Economic Approach For Electrification Of Rural And Shrimp Farming Regional Development Of An Isolated Island In Indonesia By Utilizing Hybrid Renewable Energy Systems, Fiqih Akbar Wijaya, Mohammad Akita Indianto

Journal of Materials Exploration and Findings

One of the challenges in developing and archipelagic countries such as Indonesia is maintaining energy demand in rural and isolated areas due to difficulties in electrical distribution. For instance, in areas like Bawean Island, no additional electricity capacity has been introduced in the past year, leading to an unmet potential customer demand. One of the possible options is by utilizing Hybrid Renewable Energy Systems (HRES) that are integrated with existing fossil fuel-based energy systems to support the growing energy demand in the remote island. A case study in Bawean Island is conducted with the projected energy demand covers the energy …

Remaining Life Assessment And Fitness For Service Evaluation Of Aging Chemical Reactors In Polyethylene Terephthalate Resin Industry, Aditya Pahlawan Munthe, Donanta Dhaneswara, Wahyuaji Narottama Putra, Gama Widyaputra

Journal of Materials Exploration and Findings

Aging chemical reactors in the polyethylene terephthalate (PET) resin industry require comprehensive evaluation to ensure safe continued operation. This study conducts a remaining life assessment (RLA) and fitness-for-service (FFS) evaluation on five 30-year-old reactors, based on API 510, API 579/ASME FFS-1, and ASME BPVC Section VIII Div. 1 standards. The analysis involves corrosion rate measurement, future corrosion allowance (FCA) projection, and minimum thickness verification. Among the reactors, R-120 was found to have the shortest remaining life less than 15 years. FFS assessments using three criteria Average Measured Thickness, MAWP from Point Thickness Readings, and Minimum Measured Thickness confirm that R-120 …

Analysis Of Leak Testing Planning For Carbon Dioxide Piping Systems In The Development Of Carbon Capture, Utilization, And Storage Facilities In The Bintuni Basin, Devi Sentiani, Akhmad Herman Yuwono Professor

Journal of Materials Exploration and Findings

Carbon Capture, Utilization, and Storage (CCUS) technologies have become a key strategic response to global efforts to reduce CO₂ emissions. This study presents a leak testing strategy designed for a carbon dioxide (CO₂) piping system as part of a Carbon Capture, Utilization, and Storage (CCUS) project in the Bintuni Basin, West Papua, Indonesia. This study aims to ensure the system is properly prepared before commissioning by designing a leak test plan that is both practical and technical, based on ASME B31.3, ASME PCC-2, and API STD 520 Part 1. We conducted the process, which involves identifying the system boundaries, …

Stokes-Dependent Droplet Collection Efficiency On A Naca 0012 Airfoil From Droplet-Informed Simulations With Statistical Overloading, Arash Shad, Hashnayne Ahmed, ‪Nadim Zgheib, S. Balachandar, S. A. Sherif

Mechanical Engineering Faculty Publications

Accurate modelling of ice accretion on aircraft wings requires analysing droplet impingement on the surface to optimize the design of ice-protection systems. We perform Euler–Lagrange simulations of a droplet-laden flow impinging on a NACA 0012 airfoil. Our study includes water droplets with eight discrete sizes ranging from 1 to 160 microns. We vary the free-stream velocity of the incoming airflow in the range 60≤⁢𝑈≤⁢240 m s−1 and the chord length of the airfoil in the range 0.5≤⁢𝑐≤⁢2 m. Due to the dilute nature of supercooled clouds, one-way coupling is used in the simulations. The effects of droplet breakup and collision …

A Rigorous Framework For An Improved Messinger/Myers Model Of Ice Accretion Under Conditions Of Variable Property And Unsteady Aircraft Icing, Hashnayne Ahmed, Arash Shad, ‪Nadim Zgheib, S. A. Sherif, S. Balachandar

Mechanical Engineering Faculty Publications

We analyse the Messinger/Myers model by critically evaluating simplifying assumptions through a rigorous formulation of the rime ice accretion process. We explore the effects of both constant and variable ice density and thermal conductivity, along with the effects of sublimation from the ice surface. The effects of key factors such as droplet impact rate, ambient temperature relative to the freezing temperature and the temperature difference between the ambient air and the airfoil surface are examined. Under these varying conditions, the present rigorous formulation is used to assess the significance of unsteady effects, variable ice properties and sublimation. We observe that …

Numerical Simulation Of Frost Formation And Heat Transfer On Fin-And-Tube Heat Exchangers In Turbulent Cross-Flow, Mahsan Farzaneh, ‪Nadim Zgheib, S. Balachandar, S. A. Sherif

Mechanical Engineering Faculty Publications

Frost formation in fin-and-tube heat exchangers in turbulent cross-flow presents significant challenges in industrial refrigeration applications, affecting heat transfer efficiency and operational reliability. The purpose of this work is to investigate frost deposition and growth on a staggered bank of a fin-and-tube freezer coil under turbulent forced convection conditions. The focus here is on investigating conditions that closely replicate real-world scenarios in large walk-in industrial freezers. Using a direct numerical simulation approach, we examine the flow dynamics and thermal behaviour in the presence of frost, considering turbulent regimes characterized by a Reynolds number in the range 1050≤𝑅⁢𝑒𝐷,avg≤4800, with the characteristic …

Assessment Of H2s-Induced Cracking Susceptibility In Steam Line Pipes And Weld Zones During Geothermal Well Construction, Riene Kaelamanda Pragitta, Yudha Pratesa

Journal of Materials Exploration and Findings

The susceptibility of steam line pipes, especially in the HAZ (heat-affected zone) and weldment areas, to hydrogen sulfide in the geothermal industry is crucial to understand from the early stages, particularly during construction. The combination of tensile stress from residual stresses after welding and metallurgical phase transformation makes the joint areas vulnerable to sulfide stress cracking. This condition becomes even more extreme when the equipment operates during the well stimulation phase. This research assesses the severity of H₂S-induced cracking using NACE MR0175 and ISO 15156-1 standards, focusing on the effects of pH and partial pressure of H₂S (p_{H₂S …}

A Comparison And Investigation Of 2d Axisymmetric And 3d Models For The Wave Augmented Varicose Explosions Atomizer, Caleb Miller

Senior Honors Theses

Atomization of non-Newtonian, high-viscosity fluids is a challenging task with many applications. One method of atomizing these types of flows is the Wave Augmented Varicose Explosions (WAVE) atomizer. Using this framework, the study establishes an analysis methodology, investigates the relationship between 2D axisymmetric (2DA) and 3D models, and provides analysis of geometric, non-geometric, and non-dimensional parameter influences on the atomizer characterization in 2DA models. The study found that 2DA models can provide viable predictions of certain 3D model characteristics, established several mathematical models for parameter relationships among 2DA models, and identified certain metrics as inadequate predictors of atomizer characteristics in …

Simulating Positive Ion Distribution In The Protodune Single Phase Detector, Vishnu Pfeiffer

Electronic Theses and Dissertations

This work covers the validation and implementation of a model to solve for argon ion (Ar+) distribution in the ProtoDUNE-SP liquid argon time projection chamber (LArTPC). ProtoDUNE-SP undergoes a constant flux of cosmic ray muons due to surface operation. The performance of the ProtoDUNE-SP provided valuable insights into single-phase technology, membrane cryostat technology, and calibration of cryogenic instrumentation. Still, challenges in achieving precise measurements persist due to the space charge effect—the distortion of the electric field within the detector due to the accumulation of positive argon ions generated from constant cosmic muon flux. The overarching goal of this thesis is …

Drag Reduction In Ground Vehicles Using A Model Porous Medium, Abdullah Ikram Nabi

Master’s Theses

This research investigates aerodynamic drag reduction on a 25° Slanted Ahmed Body (SAB) by integrating porous media model rods through combined experimental and computational methods at a Reynolds number of 1.16×10⁴. Two porous media configurations: short rods (6.75% of the model height) and long rods (20.0% of the model height), both featuring cylindrical rods with 80% porosity, were systematically compared against a baseline SAB. In-depth analyses were performed to investigate the wake flow topology, recirculation region characteristics, pressure coefficient distribution, Reynolds stress distributions and drag coefficient. Experimental investigations employed particle image velocimetry for precise flow visualization, while Reynold Averaged Navier-Stokes …

Effects Of Ti Addition On The Characteristics Of Al-10zn-6mg-2si/Zro2 Composites Produced By Squeeze Casting, Qesha Diva Prameshvara, Pipin Indah Lestari, Bondan Tiara Sofyan

Journal of Materials Exploration and Findings

Metal matrix composite (MMC) with 7xxx aluminum matrix is potential for ballistic applications due to the combination of strength, toughness, and light weight. Previous study successfully produced aluminum-based composites with SiC particles which were able to stop type III bullet, however cracks remained on back of the plate. Therefore, in this research, SiC was replaced by zirconia (ZrO₂) due to its high fracture toughness. Ti-B grain refiner was added to further improve toughness through grain boundary strengthening mechanism. This research developed 5 vol.% ZrO₂ strengthened Al-10Zn-6Mg-2Si composite with addition of Al-5Ti-1B grain refiner produced through squeeze casting …

Analysis Of The Effect Of Different Surface Preparation Methods On Corrosion Resistance And Adhesion Strength Of Astm A36 Steel Substrate With Surface Tolerant Epoxy Paint As Coating Material, Irwan Wijaya Santoso, Daffa Aqila, Rini Riastuti, Rizal Tresna Ramadhani

Journal of Materials Exploration and Findings

In the industrial world, to extend the service life of materials, protection methods are carried out to slow down the material's corrosion rate. The protection method that is often used is the coating method. The coating method is a protection method by coating the substrate material using a coating material to prevent contact between the substrate material and the environment. In this research, the substrate material used is ASTM A36 steel and the coating material used is Surface Tolerant Epoxy paint. The independent variable used in this study lies in the surface preparation method which consists of: solvent cleaning, hand …

Blade Design And Validation Of Hydrokinetic Turbine To Harvest Water Current Energy, Setare Sadeqi

LSU New Orleans Theses and Dissertations

The innovative aspect of this research lies in the careful integration of cutting-edge technologies throughout the entire process of designing, fabricating, and testing the carbon fiber propeller for the 3-bladed horizontal axis ocean current turbine (OCT). SolidWorks software played a pivotal role in the initial design phase, enabling a meticulous and precise modeling of the propeller's geometry. The utilization of SolidWorks allowed for a detailed exploration of various design parameters, ensuring that the propeller's structure and form were optimized for performance in ocean current conditions. Moving beyond the realm of virtual design, the choice of carbon fiber as the fabrication …