Fluid Dynamics Commons^™

Electroosmotic Flow Of Viscoelastic Fluid In A Nanoslit, Lanju Mei, Hongna Zhang, Hongxia Meng, Shizhi Qian

Mechanical & Aerospace Engineering Faculty Publications

The electroosmotic flow (EOF) of viscoelastic fluid in a long nanoslit is numerically studied to investigate the rheological property effect of Linear Phan-Thien-Tanner (LPTT) fluid on the fully developed EOF. The non-linear Poisson-Nernst-Planck equations governing the electric potential and the ionic concentration distribution within the channel are adopted to take into account the effect of the electrical double layer (EDL), including the EDL overlap. When the EDL is not overlapped, the velocity profiles for both Newtonian and viscoelastic fluids are plug-like and increase sharply near the charged wall. The velocity profile resembles that of pressure-driven flow when the EDL is …

Mechanisms And Identification Of Unsteady Separation Development And Remediation, Matthew Scott Melius

Dissertations and Theses

Unsteady flow separation represents a highly complex and important area of study within fluid mechanics. The extent of separation and specific time scales over which it occurs are not fully understood and has significant consequences in numerous industrial applications such as helicopters, jet engines, hydroelectric turbines and wind turbines. A direct consequence of unsteady separation is the erratic movement of the separation point which causes highly dynamic and unpredictable loads on an airfoil. Current computational models underestimate the aerodynamic loads due to the inaccurate prediction of the emergence and severity of unsteady flow separation especially in response to a sudden …

Automated Cfd Optimization To Maximize Wind Farms Performance And Land Use, Rafael Valotta Rodrigues

Electronic Theses and Dissertations

In this research, a computational system was designed to analyze and optimize the layout of wind farms under variable operational conditions. At first, a wind turbine computational fluid dynamic (CFD) model was developed covering the near wake. The near wake flow field was validated against near wake velocity data from the MEXICO experiment. The CFD simulation demonstrated that the tip speed ratio and the pitch angle greatly influence the near wake behavior, affecting the velocity deficit and the turbulence intensity profile in this region. The CFD model was extended to cover the far wake, aiming to become a computational tool …

Characterization Of Rotary Bell Atomizers Through Image Analysis Techniques, Jacob E. Wilson

Theses and Dissertations--Mechanical and Aerospace Engineering

Three methods were developed to better understand and characterize the near-field dynamic processes of rotary bell atomization. The methods were developed with the goal of possible integration into industry to identify equipment changes through changes in the primary atomization of the bell. The first technique utilized high-speed imaging to capture qualitative ligament breakup and, in combination with a developed image processing technique and PIV software, was able to gain statistical size and velocity information about both ligaments and droplets in the image data. A second technique, using an Nd:YAG laser with an optical filter, was used to capture size statistics …

Analyzing The Spectral Energy Cascade In Turbulent Channel Flow, João Rodrigo Andrade, Ramon Silva Martins, Gilmar Mompean, Laurent Thais, Thomas B. Gatski

CCPO Publications

An analysis of the spectral turbulent kinetic energy budget in a fully developed turbulent plane channel flow is performed. Direct numerical simulation data are evaluated at friction Reynolds numbers Re_τ of 180 and 1000. The analysis is focused on the influence of the Reynolds number on the spectral cascade of energy and the corresponding energy cascade in physical space in the presence of inhomogeneity and anisotropy. The turbulent kinetic energy distribution is compared for both Reynolds numbers, and the relevant characteristics of the energy transfer process in a wall-bounded turbulent flow are described. Differences in energy cascade are noted …

Universality Of Local Dissipation Scales In Turbulent Boundary Layer Flows With And Without Free-Stream Turbulence, Sabah F. H. Alhamdi, Sean C. C. Bailey

Mechanical Engineering Faculty Publications

Measurements of the small-scale dissipation statistics of turbulent boundary layer flows with and without free-stream turbulence are reported for Re_τ ≈ 1000 (Re_θ ≈ 2000). The scaling of the dissipation scale distribution is examined in these two boundary conditions. Results demonstrated that the local large-scale Reynolds number based on the measured longitudinal integral length scale fails to properly normalize the dissipation scale distribution near the wall in these two free-stream conditions due to the imperfect characterization of the upper bound of the inertial cascade by the integral length scale. A surrogate found from turbulent kinetic energy and …

A High Quality, Eulerian 3d Fluid Solver In C++, Lejon Anthony Mcgowan

Computer Science and Software Engineering

Fluids are a part of everyday life, yet are one of the hardest elements to properly render in computer graphics. Water is the most obvious entity when thinking of what a fluid simulation can achieve (and it is indeed the focus of this project), but many other aspects of nature, like fog, clouds, and particle effects. Real-time graphics like video games employ many heuristics to approximate these effects, but large-scale renderers aim to simulate these effects as closely as possible.

In this project, I wish to achieve effects of the latter nature. Using the Eulerian technique of discrete grids, I …

A Mathematical Model And Numerical Simulations Of Redox Electrochemical Systems With Mhd And Natural Convection, Kakkattukuzhy M. Isaac, Fangping Yuan

Collaborative Research: Actively Controllable Microfluidics with Film-Confined Redox-Magnetohydrodynamics -- Video and Data

A comprehensive mathematical model for redox electrochemical systems with magnetohydrodynamics (MHD) and natural convection are presented. The model is based on density changes in isothermal systems that accompany redox reaction at the electrode due to supporting electrolyte ions migrating into and out of the diffusion layer to satisfy electroneutrality. Numerical simulations have been performed for an axisymmetric, milli-electrode electrochemical cell with gravity directed along the axis in both directions to investigate the effect of the electrode orientation with respect to gravity. Results show that natural convection is significant in both cases, with the maximum velocity being an order of magnitude …

Evaluation And Enhancement Of Clean Energy Systems: Analytical, Computational And Experimental Study Of Solar And Nuclear Cycles, Nima Fathi

Mechanical Engineering ETDs

Clean (and specifically renewable) energy is steadily improving its global share. However, finite availability of fossil fuels and the growing effects of climate change make it an urgent priority to convince the industry and governments to incentivize investment in the renewable energy field and to make it more attractive by decreasing the capital cost. Until recently, uncertainties in funding limited renewable energy development, especially in the US. That limitation has been one of the barriers to progress. Another limitation of many renewable energy systems is the variability in their output, which makes them unsuitable for baseline power production. Therefore, fossil …

Natural Convection In Redox Electrochemistry: Model, Simulation And Experiments, Fangping Yuan, Kakkattukuzhy M. Isaac

Collaborative Research: Actively Controllable Microfluidics with Film-Confined Redox-Magnetohydrodynamics -- Video and Data

No abstract provided.

Characterization Of The Shock Wave Structure In Water, Emilie Teitz

Master's Theses (2009 -)

The scientific community is interested in furthering the understanding of shock wave structures in water, given its implications in a wide range of applications; from researching how shock waves penetrate unwanted body tissues to studying how humans respond to blast waves. Shock wave research on water has existed for over five decades. Previous studies have investigated the shock response of water at pressures ranging from 1 to 70 GPa using flyer plate experiments. This report differs from previously published experiments in that the water was loaded to shock pressures ranging from 0.36 to 0.70 GPa. The experiment also utilized tap …

An Experimental Investigation Of Wing-Tip Vortex Decay In Turbulence, Hai G. Ghimire, Sean C. C. Bailey

Mechanical Engineering Faculty Publications

Particle image velocimetry measurements were conducted for a wing-tip vortex decaying in free-stream turbulence. The vortex exhibited stochastic collapse with free-stream turbulence present, with the breakdown initiating earlier for higher levels of turbulence. An increased rate of decay of the vortex tangential velocity was also observed, increasing with increasing free-stream turbulence. The decay of the vortex tangential velocity without the free-stream turbulence was well represented by viscous diffusion, resulting in an increase in the core radius and decrease in the peak tangential velocity. With the addition of free-stream turbulence, the rate of decay of the peak tangential velocity of the …

Optimizing Jets For Wake Control Of Ground Vehicles, Domenic Barsotti, Sandra Boetcher

Publications

A system of wake control for a ground vehicle to help promote increased fuel efficiencies of the ground vehicle by modifying an air flow wake generated during the movement of the vehicle in a forward direction. The system includes at least one slot jet configured to be located along a rear profile portion of the ground vehicle. The at least one slot jet is configured to provide a continuous flow of air at a non-zero velocity when the ground vehicle is moving in a forward direction, the non-zero velocity being at least partially directed in a rearward direction with an …

Multi-Stage Axial Compressor With Counter-Rotation, Vinod Gehlot, Magdy S. Attia, Divyam Garg

Publications

A multi-stage axial compressor incorporating a counter-rotational movement is provided with a series of rotors mounted along and driven by a driveshaft, and a geared counter-rotating outer casing. A planetary gear system is assembled along a static casing, which can be assembled as a forward or aft casing for the compressor. The bearings of the planetary gear system typically will be aligned concentrically with a center rotor drum assembly mounted along the single driveshaft. The counter-rotating drum assembly will be assembled over the rotor drum assembly and will be engaged by the forward and aft casings so as to provide …

A Physics-Based Approach To Modeling Wildland Fire Spread Through Porous Fuel Beds, Tingting Tang

Theses and Dissertations--Mechanical and Aerospace Engineering

Wildfires are becoming increasingly erratic nowadays at least in part because of climate change. CFD (computational fluid dynamics)-based models with the potential of simulating extreme behaviors are gaining increasing attention as a means to predict such behavior in order to aid firefighting efforts. This dissertation describes a wildfire model based on the current understanding of wildfire physics. The model includes physics of turbulence, inhomogeneous porous fuel beds, heat release, ignition, and firebrands. A discrete dynamical system for flow in porous media is derived and incorporated into the subgrid-scale model for synthetic-velocity large-eddy simulation (LES), and a general porosity-permeability model is …

Exploiting Modern Image Processing In Surface Flow Visualisation, Tarek Ihab Abdelsalam, Richard Williams, Grant Ingram

Mechanical Engineering

Surface flow visualisation is an experimental technique where the surface of interest is painted with an oil and dye mixture before a flow is applied to the object. In regions of high shear stress the oil/dye mixture is then removed and in regions of low shear stress the oil/dye mixture stays or builds up. The resulting pattern can be analysed to determine the structure near the surface under test, this is normally done in a qualitative manner with flow structures being identified based on the expertise of the experimentalist. Modern image processing tools can identify shapes and lines in pictures …

Wave Motion Induced By Turbulent Shear Flows Over Growing Stokes Waves, Shahrdad Sajjadi, Serena Robertson, Rebecca Harvey, Mary Brown

Publications

The recent analytical of multi-layer analyses proposed by Sajjadi et al. (J Eng Math 84:73, 2014) (SHD14 therein) is solved numerically for atmospheric turbulent shear flows blowing over growing (or unsteady) Stokes (bimodal) water waves, of low-to-moderate steepness. For unsteady surface waves, the amplitude a(t)∝ekcita(t)∝ekcit, where kcikci is the wave growth factor, k is the wavenumber, and cici is the complex part of the wave phase speed, and thus, the waves begin to grow as more energy is transferred to them by the wind. This will then display the critical height to a point, where the thickness of the inner …

Computational Fluid Dynamics Is Key To Better Flying Aircraft, Nihad E. Daidzic

Aviation Department Publications

No abstract provided.

Plasma Processes And Polymers Third Special Issue On Plasma And Cancer, Mounir Laroussi, Annemie Bogaerts, Nazir Barekzi

Electrical & Computer Engineering Faculty Publications

(First paragraph) This issue of Plasma Processes and Polymers is the third in a series on the applications of low temperature plasma (LTP) against cancer, or “plasma oncology.” The papers in this issue are inspired from the talks given at the third International Workshop on Plasma for Cancer Treatment (IWPCT) which took place on April 11–12, 2016 in Washington, DC, USA. IWPCT is an international workshop that was created in 2014 as a venue to share cutting edge plasma oncology research. The first IWPCT was held in Washington DC, under the co-chairmanship of Prof. Mounir Laroussi (Old Dominion University) and …

Thermoelectric Magnetohydrodynamic Effects In Solidification Processes, Andrew Kao, Koulis Pericleous, Peter Lee, Biao Cai, Jianrong Gao

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Natural Convection And Forced Convection Model Based On Electroneutrality And Migration In Redox Mhd Systems, Fangping Yuan, Kakkattukuzhy M. Isaac

Collaborative Research: Actively Controllable Microfluidics with Film-Confined Redox-Magnetohydrodynamics -- Video and Data

No abstract provided.

Puddle Jumping: Spontaneous Ejection Of Large Liquid Droplets From Hydrophobic Surfaces During Drop Tower Tests, Babek Attari, Mark M. Weislogel, Andrew Paul Wollman, Yongkang Chen, Trevor Snyder

Mechanical and Materials Engineering Faculty Publications and Presentations

Large droplets and puddles jump spontaneously from sufficiently hydrophobicsurfaces during routine drop tower tests. The simple low-cost passive mechanism can in turn be used as an experimental device to investigate dynamic droplet phenomena for drops up to 104 times larger than their normal terrestrial counterparts. We provide and/or confirm quick and qualitative design guides for such “drop shooters” as employed in drop tower tests including relationships to predict droplet ejection durations and velocities as functions of drop volume, surface texture, surface contour, wettability pattern, and fluid properties including contact angle. The latter is determined via profile image comparisons with numerical …

A Fast Model For The Simulation Of External Gear Pumps, Zechao Lu, Xinran Zhao, Andrea Vacca

The Summer Undergraduate Research Fellowship (SURF) Symposium

External gear pump is an important category of positive displacement fluid machines used to perform the mechanical–hydraulic energy conversions in many fluid power applications. An efficient numerical simulation program is needed to simulate the system in order to provide a direction for design purpose. The model consists of a lumped parameter fluid dynamic model and a model that simulates the radial micro-motions of the gear’s axes of rotation. The system consists of a set of ordinary differential equations related to the conservation on mass of the internal control volumes of the pump, which are given by the tooth space volumes …

Chaotic Advection-Driven Mixing In Unsteady Three-Dimensional Mhd Flows In Microfluidic Devices, Fangping Yuan, Kakkattukuzhy M. Isaac

Collaborative Research: Actively Controllable Microfluidics with Film-Confined Redox-Magnetohydrodynamics -- Video and Data

No abstract provided.

Large Length Scale Capillary Fluidics: From Jumping Bubbles To Drinking In Space, Andrew Paul Wollman

Dissertations and Theses

In orbit, finding the "bottom" of your coffee cup is a non-trivial task. Subtle forces often masked by gravity influence the containment and transport of fluids aboard spacecraft, often in surprising non-intuitive ways. Terrestrial experience with capillary forces is typically relegated to the micro-scale, but engineering community exposure to large length scale capillary fluidics critical to spacecraft fluid management design is low indeed. Low-cost drop towers and fast-to-flight International Space Station (ISS) experiments are increasing designer exposure to this fresh field of study. This work first provides a wide variety of drop tower tests that demonstrate fundamental and applied capillary …

Particle Image Velocimetry Design & Installation, Zach Ritchie

Mechanical Engineering Undergraduate Honors Theses

This work will mainly focus on the design, construction, and installation of the Particle Image Velocimetry (PIV) system in the Chemical Hazards Research Center wind tunnel. The PIV system utilizes a Class IV (double pulsed) laser, optics to produce a light sheet, timing circuitry, and a high-resolution camera (with buffered output) to measure a system’s velocity (two-dimensional) field by determining the displacement of particles over the time between laser pulses. For maximum mobility and functionality, the PIV system was installed in the center of the tunnel on a moveable cart with the laser and camera mounted to an adjustable support. …

Spatio-Temporal Linear Stability Analysis Of Stratified Planar Wakes: Velocity And Density Asymmetry Effects, Benjamin Emerson, Swapnil Jagtap, J. Mathew Quinlan, Michael W. Renfro, Baki M. Cetegen, Tim Lieuwen

Mechanical Engineering Faculty Publications

This paper explores the hydrodynamic stability of bluff body wakes with non-uniform mean density, asymmetric mean density, and velocity profiles. This work is motivated by experiments [S. Tuttle et al., “Lean blow off behavior of asymmetrically-fueled bluff body-stabilized flames,” Combust. Flame 160, 1677 (2013)], which investigated reacting wakes with equivalence ratio stratification and, hence, asymmetry in the base flow density profiles. They showed that highly stratified cases exhibited strong, narrowband oscillations, suggestive of global hydrodynamic instability. In this paper, we present a local hydrodynamic stability analysis for non-uniform density wakes that includes base flow asymmetry. The results show …

More Investigations In Capillary Fluidics Using A Drop Tower, Andrew Paul Wollman, Mark M. Weislogel, Brentley M. Wiles, Donald Pettit, Trevor Snyder

Mechanical and Materials Engineering Faculty Publications and Presentations

A variety of contemplative demonstrations concerning intermediate-to-large length scale capillary fluidic phenomena were made possible by the brief weightless environment of a drop tower (Wollman and Weislogel in Exp Fluids 54(4):1, 2013). In that work, capillarity-driven flows leading to unique spontaneous droplet ejections, bubble ingestions, and multiphase flows were introduced and discussed. Such efforts are continued herein. The spontaneous droplet ejection phenomena (auto-ejection) is reviewed and demonstrated on earth as well as aboard the International Space Station. This technique is then applied to novel low-g droplet combustion where soot tube structures are created in the wakes of burning drops. …

Effect Of Spalled Particles Thermal Degradation On A Hypersonic Flow Field Environment, Raghava S. C. Davuluri, Huaibao Zhang, Alexandre Martin

Mechanical Engineering Faculty Publications

Two-way coupling is performed between a spallation code and a hypersonic aerothermodynamics CFD solver to evaluate the effect of spalled particles on the flow field. Time accurate solutions are computed in argon and air flow fields. A single particle simulations and multiple particles simulations are performed and studied. The results show that the carbon vapor released by spalled particles tend to change the composition of the flow field, particularly the upstream region of the shock.

Quantitative Assessment Of Secondary Flows Of Single-Phase Fluid Through Pipe Bends, Z. Kaldy, O. Ayala

Engineering Technology Faculty Publications

Single-phase fluid flow was simulated passing through various three dimensional pipe elbows. The simulations varied by Reynolds number, curvature ratios, and sweep angles and were all conducted using the k-e model available in COMSOL Multiphysics 5.1. The intent of this research was to qualitatively assess the flow characteristics under several different conditions. Many similarities were seen especially when comparing curvature ratios, the vorticity location for the turbulent cases show near identical behavior at the elbow midsection. One of the variables quantified in this paper is the maximum secondary velocity module which shows increasing values until the midsection of the elbow.