Fluid Dynamics Commons^™

Exploring Red Palm Oil As A Sustainable Plasticizer For Carbon Black-Filled Ssbr/Br Tire Tread Compounds: A Comparative Evaluation Of Commercial Alternatives, Norma Arisanti Kinasih, Mohamad Irfan Fathurrohman, Santi Puspitasari, Dewi Kusuma Arti, Abdulhakim Masa

Journal of Materials Exploration and Findings

This study investigates the application of red palm oil (RPO) as an alternative vegetable oil resource to substitute petroleum-based plasticizers, which have environmental and health concerns, in carbon black (CB)-filled SSBR/BR tire tread compounds. The plasticizing effects of RPO were thoroughly evaluated by comparing them with a commercial bio-based plasticizer, Epoxidized Soybean Oil (ESBO), and two safer petroleum-based oils, Naphthenic Oil (NYNAS) and Treated Distillate Aromatic Extract (TDAE). The initial investigation shows that fatty acid composition is imposing regarding the plasticizing effect. The higher unsaturated fatty acid content in RPO than in ESBO improved tensile strength and degraded rolling resistance …

Metallurgical Investigation Of A Modified Eye Bolt Failure Caused By Improper Weld Extension, Specification Deviation, And Crevice Corrosion, Dimas Muhammad Fawwaz, Reza Miftahul Ulum, Johny Wahyuadi Soedarsono, Yudha Pratesa

Journal of Materials Exploration and Findings

A modified eye bolt from the David Arm Manhole Storage Tank underwent thorough metallurgical study due to the consequences of the bolt's malfunction during operation. Safety issues arose when the manhole door detached during operation. The mechanical testing and chemical composition analysis of the bolts indicated they were manufactured from an ASTM A193 Grade B7 material used for high-temperature bolting. This material did not conform to the engineering drawing, which mentioned SA 563A, which is about nuts, not bolts. This contradiction clearly shows that the eye bolt which was installed does not conform to the intended design. Welded connections of …

Rejection Of Fe (Iron) And Kmno4 (Organic Substance) Parameters In Peat Water Using Organic Membranes, Muhamad Rafli Sakti Mulia Gonera, Siti Umi Kalsum, Sarah Fiebrina Heraningsih

Journal of Materials Exploration and Findings

Peat water is a surface water source widely used by people in swampy and lowland areas, but it has poor quality characteristics such as high organic matter content, low pH, and dissolved metal levels such as iron that exceed the threshold. These conditions can cause health problems and reduce the quality of clean water so that effective treatment technology is needed. This study aims to analyze the effectiveness of ultrafiltration membranes made from chitosan from shrimp shell waste in rejecting iron (Fe) and organic substances in peat water, and to determine the effect of pressure on separation performance. This study …

Feasibility Analysis Of Thermal Oxidizer To Determine Remaining Life Using Fitness- For-Service Level 3 Method, Yudhi Yudistirawan, Donanta Dhaneswara, Wahyuaji Narottama Putra, Gama Widyaputra, Dewi Kurnia Suci, Agung Putra Mahardhika

Journal of Materials Exploration and Findings

An aged thermal oxidizer (TOX) in the oil and gas industry necessitates a comprehensive evaluation to ensure its continued safe operation. This study presents a Remaining Life Assessment (RLA) and a Fitness for Service (FFS) evaluation for the four main components of the TOX, in accordance with API 510, API 579/ASME FFS-1, and ASME BPVC Section VIII Div-1 standards. The investigation includes the determination of maximum stress and maximum temperature required to assess the operational viability of the reactor. The four components are radiant, convection, transition, and stack sections—were modeled using the finite element method (FEM). Following the geometric modeling, …

Numerical Study Of Nutrient Mixing In Trabecular Bone In Microgravity, Disuse And Normogravity, Sagar Gharti

Doctoral Dissertations and Master's Theses

Mechanical loading is known to regulate bone remodeling by driving interstitial fluid flow which stimulates cells and drives nutrient transport within the trabecular network. In microgravity, the absence of mechanical stimulation or loading suppresses convective flow processes, causing diffusion-driven nutrient mixing and renewal, and accelerated bone loss. This thesis investigates how oscillation frequency and trabecular bone density jointly control nutrient mixing and wall shear stress within trabecular cavities.

A computational fluid dynamics (CFD) framework is developed in STAR-CCM+ using a soft-cap oscillation model that mimics cyclic compression. Three idealized trabecular morphologies are simulated across different frequencies to represent microgravity or …

Computational Study Of Rotating Detonation Combustors, Aditya Balasubramaniam

Mechanical and Aerospace Engineering Theses

Rotating detonation combustors (RDCs) are pressure-gain combustion devices that sustain one or more continuously rotating detonation waves, offering potential thermodynamic and performance advantages over conventional deflagration-based systems. Their behavior depends strongly on combustor geometry and operating conditions. Understanding these effects is therefore essential for the design and optimization of practical RDCs. Accordingly, this thesis numerically investigates annular RDCs with two primary objectives: (1) to evaluate the effects of propellant mass flux and (2) to assess the influence of annular width on detonation-wave dynamics and combustor performance.

A finite-volume framework is used to solve the compressible reactive Euler equations with hydrogen–air …

Analysis Of Leakage In Nearshore Pipelines Using Fitness For Service Method To Ensure Mechanical Integrity Based On Api-579 Level 3, Elriandri Elriandri, Dedi Priadi

Journal of Materials Exploration and Findings

The Fitness for Service (FFS) analysis is performed as a quantitative assessment to evaluate the integrity condition of a pipeline. Essentially, FFS assessment helps determine whether equipment components can operate safely despite existing deficiencies. This evaluation is carried out using the Finite Element Method (FEM). In the case of an underwater pipeline that experiences leak due to anchor pull at the flange connection, it undergoes plastic deformation and is lifted approximately 1 meter. As a mitigation step, inspection and repairs have been carried out by the company. Subsequently, modeling is performed to reconstruct the deformation process of the pipeline. Then, …

Assessment Of The Melt Quality Of A 30% Scrap Adc12 Aluminium Alloy Using The Inclusion And Fluidity Measurement Instrument (Ifmi) With Mullite Ceramic Filters, Gusti Ruri Ruri Lestari, Sandya Ananda Riswan, Muhammad Anis, Ahmad Ashari, Paramita Vidya Ayuningtyas, Bambang Suharno Prof, Donanta Dhaneswara

Journal of Materials Exploration and Findings

The increasing demand for sustainable practices in the metal casting industry has driven the use of recycled aluminum alloys such as ADC12. However, the addition of aluminum scrap tends to increase oxide inclusions, which reduce melt fluidity and compromise casting quality. This study utilizes the Inclusion and Fluidity Measurement Instrument (IFMI), equipped with mullite ceramic filters, to assess the melt quality of ADC12 aluminum alloy containing 30% scrap. Fluidity and inclusion characteristics were evaluated at five pouring temperatures (660°C, 680°C, 700°C, 720°C, and 740°C). The results show that fluidity increased with temperature, reaching a peak of 84.6 g·s⁻¹ at 740°C, …

Equipment Criticality Analysis To Determine Asset Integrity Management System Scheme In Supporting Production Optimization Scenarios In The Aeging Field, Donny Andryanto, Donanta Dhaneswara

Journal of Materials Exploration and Findings

This research investigates the production decline and cost increase in the X&Y oil and gas fields from 2022 to 2023. Production fell by 34%, while production costs per barrel rose by 79%. To address these issues, a series of optimization processes are proposed. These aim to restructure and enhance the production facilities to reduce current production costs. The optimizations include reducing pressure at the PPP Platform in 2024. Additional steps include shutting down CPP-ORF 14” pipelines and most processes at CPP 2 Platform by 2027 to convert it into an accommodation platform. Further, the plan involves optimizing the release of …

Morphological Test Of Areca Nut Fiber Ceramic Membrane Using Scanning Electron Microscopy Energy Dispersive X-Ray Mapping Spectroscopy, Amelia Marzain, Siti Umi Kalsum, Marhadi Marhadi, Ahmad Nabil Shahab

Journal of Materials Exploration and Findings

This study investigates the potential of ceramic membranes derived from areca nut fiber as a cost-effective and environmentally sustainable material for the removal of iron (Fe) and manganese (Mn) from groundwater. Two types of membranes were fabricated: one without activation and one chemically activated using 10% sodium hydroxide (NaOH). The morphological and elemental characteristics of both membranes were analyzed using Scanning Electron Microscopy (SEM) and Energy Dispersive X-ray (EDX) mapping. The concentrations of Fe and Mn before and after treatment were measured using Atomic Absorption Spectroscopy (AAS). The NaOH-activated membrane exhibited a more porous surface structure and higher oxygen content, …

Meshless Discrete Velocity Boltzmann Model For Porous Media Flow, Amandine Maidenberg

Doctoral Dissertations and Master's Theses

This dissertation explores the combination of two sophisticated techniques for addressing computational fluid dynamics: the discrete velocity Boltzmann equation (DVBE) and the localized collocation meshless model with upwinding (U-LCMM). The DVBE is a high-level model that describes the foundations of transport phenomena by addressing the microscale motions of particles themselves and the effect of their aggregate behaviors on continuum principles. This equation integrates multiple scales of phenomena; while it can be used for fluid flow at Navier-Stokes scales, it can also resolve fine features that can only be described at the molecular level. This type of model is necessary for …

Investigation Of Co-Current And Counter-Current Multiphase Flow In Upstream Drilling And Production Applications, Hazem Fleifel

LSU Doctoral Dissertations

In the domain of upstream Petroleum Engineering, the dynamics of co-current and counter-current multiphase flows present huge challenges, significantly impacting the efficiency of associated processes. This study investigates two specific applications concerning these flow behaviors, involving both laboratory experiments and transient computer simulations. This work investigates two distinct well control and production enhancement processes, involving multiphase flow dynamics: the bullheading kill procedure and liquid-assisted gas lift (LAGL).

The first topic (Topic 1) explores the bullheading process, a type of well control methods, by challenging the traditional understanding that gas removal efficiency increases monotonically with injection pump flow rate. Through 1D …

A Study Of Wear Measurement And Life Prediction Of Insert Chute Liner On Gold Ore Processing, Ferry Ardika Natanael, Nony Maulidya, Dedi Priadi

Journal of Materials Exploration and Findings

Chutes are critical materials handling assets to transport solid particles from one process step to another in mineral processing, coal mining and cement industries. The material transport, because of material characteristics, cause severe wear on internal lining of chutes or bins’ structure. The wear problem on internal lining of bins or chutes needs to be checked to keep production efficiency. Therefore, not checked wear rate causes liner replacement schedule becomes unpredictable. It leads to production loss and highly cost maintenance in industry. This study shows that condition-based maintenance through regular thickness measurement using Ultrasonic Transducer (UT) to predict life service …

Techno-Enviro-Economic Approach For Electrification Of Rural And Shrimp Farming Regional Development Of An Isolated Island In Indonesia By Utilizing Hybrid Renewable Energy Systems, Fiqih Akbar Wijaya, Mohammad Akita Indianto

Journal of Materials Exploration and Findings

One of the challenges in developing and archipelagic countries such as Indonesia is maintaining energy demand in rural and isolated areas due to difficulties in electrical distribution. For instance, in areas like Bawean Island, no additional electricity capacity has been introduced in the past year, leading to an unmet potential customer demand. One of the possible options is by utilizing Hybrid Renewable Energy Systems (HRES) that are integrated with existing fossil fuel-based energy systems to support the growing energy demand in the remote island. A case study in Bawean Island is conducted with the projected energy demand covers the energy …

Remaining Life Assessment And Fitness For Service Evaluation Of Aging Chemical Reactors In Polyethylene Terephthalate Resin Industry, Aditya Pahlawan Munthe, Donanta Dhaneswara, Wahyuaji Narottama Putra, Gama Widyaputra

Journal of Materials Exploration and Findings

Aging chemical reactors in the polyethylene terephthalate (PET) resin industry require comprehensive evaluation to ensure safe continued operation. This study conducts a remaining life assessment (RLA) and fitness-for-service (FFS) evaluation on five 30-year-old reactors, based on API 510, API 579/ASME FFS-1, and ASME BPVC Section VIII Div. 1 standards. The analysis involves corrosion rate measurement, future corrosion allowance (FCA) projection, and minimum thickness verification. Among the reactors, R-120 was found to have the shortest remaining life less than 15 years. FFS assessments using three criteria Average Measured Thickness, MAWP from Point Thickness Readings, and Minimum Measured Thickness confirm that R-120 …

Analysis Of Leak Testing Planning For Carbon Dioxide Piping Systems In The Development Of Carbon Capture, Utilization, And Storage Facilities In The Bintuni Basin, Devi Sentiani, Akhmad Herman Yuwono Professor

Journal of Materials Exploration and Findings

Carbon Capture, Utilization, and Storage (CCUS) technologies have become a key strategic response to global efforts to reduce CO₂ emissions. This study presents a leak testing strategy designed for a carbon dioxide (CO₂) piping system as part of a Carbon Capture, Utilization, and Storage (CCUS) project in the Bintuni Basin, West Papua, Indonesia. This study aims to ensure the system is properly prepared before commissioning by designing a leak test plan that is both practical and technical, based on ASME B31.3, ASME PCC-2, and API STD 520 Part 1. We conducted the process, which involves identifying the system boundaries, …

Theoretical And Experimental Investigation Of Liquid-Liquid Phase Separation: Characterizing Elastin-Like-Polypeptides, Adam D. Quintana

Chemical and Biological Engineering ETDs

This dissertation develops and validates a semi-empirical Flory–Huggins-based interaction model, combined with Cahn–Hilliard simulations, for predicting multi-component liquid–liquid phase separation (LLPS) in elastin-like polypeptide (ELP) systems. Equilibrium droplet compositions, measured using a PDMS-based microfluidic device, enabled direct parameterization of interaction coefficients. The model was applied to generate phase diagrams and assess composition dependence in ternary mixtures. Cahn–Hilliard simulations were conducted to explore potential phase morphologies under different interfacial conditions. Multi-component Lattice Boltzmann simulations were implemented to model droplet morphology evolution under varying interfacial and diffusive parameters, reproducing experimentally relevant morphologies. A three-phase wetting study revealed conditions for selective wetting and …

Assessment Of H2s-Induced Cracking Susceptibility In Steam Line Pipes And Weld Zones During Geothermal Well Construction, Riene Kaelamanda Pragitta, Yudha Pratesa

Journal of Materials Exploration and Findings

The susceptibility of steam line pipes, especially in the HAZ (heat-affected zone) and weldment areas, to hydrogen sulfide in the geothermal industry is crucial to understand from the early stages, particularly during construction. The combination of tensile stress from residual stresses after welding and metallurgical phase transformation makes the joint areas vulnerable to sulfide stress cracking. This condition becomes even more extreme when the equipment operates during the well stimulation phase. This research assesses the severity of H₂S-induced cracking using NACE MR0175 and ISO 15156-1 standards, focusing on the effects of pH and partial pressure of H₂S (p_{H₂S …}

The Effects Of Snow Cover On The Dynamic Pressure Of Nuclear Detonation Blast Waves, Adam Card, Andrew W. Decker

Faculty Publications

Blast pressure is the primary military targeting metric for nuclear weapons. Any local conditions that affect blast pressure have the potential for altering nuclear plans, both from defensive and offensive standpoints. Understanding the impact of snow to the blast wave, therefore, provides a benefit both to military planners and to warfighters on the ground, for any operation occurring in arctic environments. No existing data provides a quantitative description of how snow on the ground affects a nuclear detonation blast wave passing over it. Similar blast waves passing over dust have experimentally proven to enhance blast pressure in a localized region.1 …

Cfd Analysis Of Hydrodynamic Cavitation Through An Orifice: Influence Of Different Inlet Pressures And Number Of Orifice Holes, Lemthong Chanphavong, Vongsavanh Chanthaboune, Keophousone Phonhalath

ASEAN Journal on Science and Technology for Development

Hydrodynamic cavitation (HC) is considered an energy-efficient process with high potential for utilization in many chemical processes. This study presents a computational fluid dynamics (CFD) analysis of cavitating flow through an orifice with a constant flow area. The Reynolds-Averaged Navier-Stokes (RANS) equations, coupled with turbulence and cavitation models, are employed to capture the complex flow behaviors. The effects of inlet pressures and number of orifice-holes on cavitation behavior are investigated. Result of the numerical simulation is validated with the existing experimental data from the literature. The CFD study revealed that cavitation initiates just behind the inlet edge of the orifice …

Analysis Of The Effect Of Different Surface Preparation Methods On Corrosion Resistance And Adhesion Strength Of Astm A36 Steel Substrate With Surface Tolerant Epoxy Paint As Coating Material, Irwan Wijaya Santoso, Daffa Aqila, Rini Riastuti, Rizal Tresna Ramadhani

Journal of Materials Exploration and Findings

In the industrial world, to extend the service life of materials, protection methods are carried out to slow down the material's corrosion rate. The protection method that is often used is the coating method. The coating method is a protection method by coating the substrate material using a coating material to prevent contact between the substrate material and the environment. In this research, the substrate material used is ASTM A36 steel and the coating material used is Surface Tolerant Epoxy paint. The independent variable used in this study lies in the surface preparation method which consists of: solvent cleaning, hand …

Improving Static Cold Storage Life Of The Human Heart Before Transplant, Juan Sebastian Rodriguez Paez

Theses and Dissertations

Organ storage and transportation are critical steps for the success of organ transplantation. Static cold storage (SCS) of hearts for heart transplantation (HTx) remains the standard approach. However, SCS may involve damage to the tissue resulting from extended hypothermic preservation, potentially affecting organ viability. More over, the temperature distribution on and within the heart is unknown during heart transplantation. Therefore, there is an interest to study different stages of the heart transplantation process towards determining the 3D temperature distribution on and within the heart. There could be a possibility of having a hypothermic injury in different parts of the heart …

Investigation Of Gas Dynamics In Water And Oil-Based Muds Using Das, Dts, And Dss Measurements, Temitayo S. Adeyemi

LSU Master's Theses

Reliable prediction of gas migration velocity, void fraction, and length of gas-affected region in water and oil-based muds is essential for effective planning, control, and optimization of drilling operations. However, there is a gap in our understanding of gas behavior and dynamics in water and oil-based muds. This is a consequence of the use of experimental systems that are not representative of field-scale conditions. This study seeks to bridge the gap via the well-scale deployment of distributed fiber-optic sensors for real-time monitoring of gas behavior and dynamics in water and oil-based mud. The aforementioned parameters were estimated in real-time using …

Hydrodynamics Of Drops And Particles Driven By Marangoni And Diffusiophoretic Forces, Subramaniam Chembai Ganesh

Dissertations and Theses

This study investigates the hydrodynamics of particles and drops driven by forces generated by an asymmetrical physical and chemical surrounding environment. In the first part, a novel colloidal motor design driven by surface tension forces is proposed, utilizing an active Janus particle encapsulated in an immiscible liquid drop to form a compound drop/particle. Marangoni forces induced by asymmetric solute adsorption at the liquid-liquid interface of the drop propels the compound system. The propulsion speeds of the motor are analyzed for various relative sizes and configurations of the Janus particle and the encapsulating drop and the effects of varying the transport …

Combined Risk Based Inspection And Fault Tree Analysis For Repetitive 3-Phase Line Piping Leakage At West Java Offshore Topside Facility, Dona Yuliati, Akhmad Herman Yuwono, D. Rizal Asral, Donanta Dhaneswara

Journal of Materials Exploration and Findings

Hydrocarbon releases might result in serious consequences in various aspects. In addition to the contribution to environmental pollution, repetitive leakages need high repair costs. This study aim is to minimize potential repetitive leakage for other typical 3-phase piping systems. We conducted the risk assessment by adopting Risk Based Inspection (RBI) API 581 to identify risk level, calculating piping lifetime, recommended inspection plan and mitigations. The most relevant root causes can be obtained through quantitative Fault Tree Analysis (FTA). Observation and investigation was taken from eight 3-phase piping systems that experienced repetitive leakages. It has been found that the risk level …

Nitrogen Gas Quenching Pressure Effect On Bs S155 Alloy Steel In Vacuum Furnace, Agus Mulyadi Hasanudin, Eddy Sumarno Siradj

Journal of Materials Exploration and Findings

The production of metal and alloy products requires the use of heat treatment, when during the heat treatment process, quenching is a crucial step. The quenching medium can be anything from water, a salt bath, oil, air and gas. In a vacuum furnace, pressurized gas, most frequently nitrogen (N₂) gas, serves as one of the quenching mediums. One of the drawbacks of the quenching process is the distortion and dimensional change of the parts. This paper aims to investigate the influence of nitrogen gas quenching pressure on the distortion and dimensional change of aerospace actuator gear planet parts …

Bacterial Motion And Spread In Porous Environments, Yasser Almoteri

Dissertations

Micro-swimmers are ubiquitous in nature from soil and water to mammalian bodies and even many technological processes. Common known examples are microbes such as bacteria, micro-algae and micro-plankton, cells such as spermatozoa and organisms such as nematodes. These swimmers live and have evolved in multiplex environments and complex flows in the presence of other swimmers and types, inert particles and fibers, interfaces and non-trivial confinements and more. Understanding the locomotion and interactions of these individual micro-swimmers in such impure viscous fluids is crucial to understanding the emergent dynamics of such complex systems, and to further enabling us to control and …

Using Computational Fluid Dynamics And Optical Sensor Technology To Scale Cell Culture Platforms, Mandar Makwana

KGI Theses and Dissertations

Different cell culture vessels ranging from micro scale to laboratory scale to commercial scale play critical role in upstream process development for biologics manufacturing. Based on the mode of operation, cell culture vessels have different hydrodynamic environments, making it challenging to scale. Integrated approaches using computational tools supported by experimental studies can overcome these challenges. Computational Fluid Dynamics (CFD) is one such tool that can simulate hydrodynamics within the cell culture vessels and can provide insights at macro and micro-scale. Accuracy of a CFD model significantly depends on the fluid model and assumptions. Traditionally, simple two-equation fluid models were developed …

Impact Of Spallation And Internal Radiation On Fibrous Ablative Materials, Raghava Sai Chaitanya Davuluri

Theses and Dissertations--Mechanical and Aerospace Engineering

Space vehicles are equipped with Thermal Protection Systems (TPS) that encounter high heat rates and protect the payload while entering a planetary atmosphere. For most missions that interest NASA, ablative materials are used as TPS. These materials undergo several mass and energy transfer mechanisms to absorb intense heat. The size and construction of the TPS are based on the composition of the planetary atmosphere and the impact of various ablative mechanisms on the flow field and the material. Therefore, it is essential to quantify the rates of different ablative phenomena to model TPS accurately. In this work, the impact of …

Thermal Analysis Of Thermal Shield For Pip-Ii Ssr1 Cryomodule, Victor Aguado Rodriguez

Graduate Research Theses & Dissertations

Fermilab's PIP-II project plans to enhance the onsite accelerator into the world's most intense neutrino beam, bringing Fermilab into the next generation of particle accelerators. The five different types of cryomodules are vital parts of the PIP-II project and each requires numerous engineering analyses to prove operation. For example, the thermal shield of the Single Spoke Resonator-1 (SSR1) cryomodule required a thermal analysis to ensure the design was operating as intended before fabrication commenced. The thermal shield is cooled by the supercritical helium inside of the extrusion and must remain between 45 and 80 Kelvin. The main purpose of the …