Engineering Physics Commons^™

Analysis Of Interband, Intraband, And Plasmon Polariton Transitions In Silver Nanoparticle Films Via In Situ Real-Time Spectroscopic Ellipsometry, S. A. Little, R. W. Collins, S. Marsillac

Electrical & Computer Engineering Faculty Publications

The dielectric function of Ag nanoparticle films, deduced from an analysis of in situ real-time spectroscopic ellipsometry (RTSE) measurements, is found to evolve with time during deposition in close consistency with the film structure, deduced in the same RTSE analysis. In the nucleation regime, the intraband dielectric function component is absent and plasmon polariton behavior dominates. Only at nuclei contact, does the intraband amplitude appear, increasing above zero. Both intraband and plasmon amplitudes coexist during surface smoothening associated with coalescence. The intraband relaxation time increases rapidly after surface smoothening is complete, also in consistency with the thin film structural evolution.

Density Functional Theory Study On The Electronic Structure Of N- And P-Type Doped Srtio3 At Anodic Solid Oxide Fuel Cell Conditions, S. Suthirakun, Salai Cheettu Ammal, G. Xiao, Fanglin Chen, Hans-Conrad Zur Loye, Andreas Heyden

Faculty Publications

The electronic conductivity and thermodynamic stability of mixed n-type and p-type doped SrTiO3 have been investigated at anodic solid oxide fuel cell (SOFC) conditions using density functional theory (DFT) calculations. In particular, constrained ab initio thermodynamic calculations have been performed to evaluate the phase stability and reducibility of various Nb- and Ga-doped SrTiO3 at synthesized and anodic SOFC conditions. The density of states (DOS) of these materials was analyzed to study the effects of n- and p-doping on the electronic conductivity. In agreement with experimental observations, we find that the transformation from 20% Nb-doped Sr-deficient SrTiO3 to a non-Sr-deficient phase …

Boron Carbide Based Solid State Neutron Detectors: The Effects Of Bias And Time Constant On Detection Efficiency, Nina Hong, John Mullins, Keith Foreman, Shireen Adenwalla

Shireen Adenwalla Papers

Neutron detection in thick boron carbide(BC)/n-type Si heterojunction diodes shows a threefold increase in efficiency with applied bias and longer time constants. The improved efficiencies resulting from long time constants have been conclusively linked to the much longer charge collection times in the BC layer. Neutron detection signals from both the p-type BC layer and the n-type Si side of the heterojunction diode are observed, with comparable efficiencies. Collectively, these provide strong evidence that the semiconducting BC layer plays an active role in neutron detection, both in neutron capture and in charge generation and collection.

Rubidium Recycling In A High Intensity Short Duration Pulsed Alkali Laser, Wooddy S. Miller

Theses and Dissertations

Laser induced fluorescence was used to study how pump pulse duration and alkali recycle time effects maximum power output in a Diode Pumped Alkali Laser (DPAL) system. A high intensity short pulsed pump source was used to excited rubidium atoms inside a DPAL-type laser. The maximum output power of the laser showed a strong dependence upon the temporal width of the pump pulse in addition to the input pump intensity. A linear relationship was observed between the maximum output power and the pulse width due to the effective lifetime of the excited state, defined as the time it takes for …

Robust Isothermal Electric Control Of Exchange Bias At Room Temperature, Xi He, Ning Wu, Anthony N. Caruso, Elio Vescovo, Kirill D. Belashchenko, Peter A. Dowben, Christian Binek

Kirill Belashchenko Publications

Voltage-controlled spin electronics is crucial for continued progress in information technology. It aims at reduced power consumption, increased integration density and enhanced functionality where non-volatile memory is combined with highspeed logical processing. Promising spintronic device concepts use the electric control of interface and surface magnetization. From the combination of magnetometry, spin-polarized photoemission spectroscopy, symmetry arguments and first-principles calculations, we show that the (0001) surface of magnetoelectric Cr₂O₃ has a roughness-insensitive, electrically switchable magnetization. Using a ferromagnetic Pd/Co multilayer deposited on the (0001) surface of a Cr₂O₃ single crystal, we achieve reversible, room-temperature isothermal switching …

Strain Energy And Lateral Friction Force Distributions Of Carbon Nanotubes Manipulated Into Shapes By Atomic Force Microscopy, Mark C. Strus, Roya R. Lahiji, Pablo Ares, Vincente Lopez, Arvind Raman, Ron R. Reifenberger

Other Nanotechnology Publications

The interplay between local mechanical strain energy and lateral frictional forces determines the shape of carbon nanotubes on substrates. In turn, because of its nanometer-size diameter, the shape of a carbon nanotube strongly influences its local electronic, chemical, and mechanical properties. Few, if any, methods exist for resolving the strain energy and static frictional forces along the length of a deformed nanotube supported on a substrate. We present a method using nonlinear elastic rod theory in which we compute the flexural strain energy and static frictional forces along the length of single walled carbon nanotubes (SWCNTs) manipulated into various shapes …

Raman Studies Of 1,3,5,7 Cyclooctatetraene At High Pressure, Martin Galley, Ed Romano, Sergey Tkachev, Michael Pravica

Undergraduate Research Opportunities Program (UROP)

We performed Raman spectroscopic studies of 1,3,5,7-cyclooctatetraene at elevated pressures up to 10 GPa with the aim of examining possible planarization of the molecule and further studying two prior-discovered phases of the solid with pressure. The Raman excitation source was a Krypton-ion laser operating at 674.1 nm (give wavelength).

1,3,5,7 Cyclooctatetraene has an octagonal formation however it is not aromatic or anti-aromatic (not a subject to the 4n+2 Huckel’s rule) [1]. As a result, its adopts a somewhat reactive tub shape. Upon the addition or removal of one to two electrons under ambient conditions, the molecule planarizes and becomes aromatic …

Ozone Concentration In An Atmospheric Pressure Air Plasma Jet, Srinivas Reddy Suddala

Electrical & Computer Engineering Theses & Dissertations

A stable micro-plasma jet in air was generated from a direct current discharge between two molybdenum electrodes (0.25 mm thick) that were separated by an alumina insulator of the same thickness. The after-glow plasma jet was generated by blowing air through the space between the electrodes. A change from laminar to turbulent flow was observed at a gas flow rate of 140 ml/min. The length of the plasma jet increased with flow rate in the laminar mode to approximately 15 mm and decreased in the turbulent mode.

Increasing the gas flow rate up to 200 ml/min at a constant discharge …

Boron-Rich Semiconducting Boron Carbide Neutron Detector, Andrew D. Harken, Ellen E. Day, Brian W. Robertson, Shireen Adenwalla

Shireen Adenwalla Papers

Data on the neutron detection capabilities of a variety of boron carbide/Si heterojunction diodes is presented. The pulse height spectra are compared with previously measured conversion layer devices and the variations in shape and position of the peaks are discussed.

Anisotropy Of Exchange Stiffness And Its Effect On The Properties Of Magnets, K. D. Belashchenko

Kirill Belashchenko Publications

Using the spin-spiral formulation of the tight-binding linear muffin-tin orbital method, the principal components of the exchange stiffness tensor are calculated for typical hard magnets including tetragonal CoPt-type and hexagonal YCo₅ alloys. The exchange stiffness is strongly anisotropic in all studied alloys. This anisotropy makes the domain wall surface tension anisotropic. Competition between this anisotropic surface tension and magnetostatic energy controls the formation and dynamics of nanoscale domain structures in hard magnets. Anisotropic domain wall bending is described in detail from the general point of view and with application to cellular Sm–Co magnets. It is shown that the repulsive …

Improvements In Wavelength Modulation Spectroscopy Using Ratios Of Higher Harmonics, James Michael Barrington

Electrical & Computer Engineering Theses & Dissertations

Experiments in Wavelength Modulation Spectroscopy have been conducted at Old Dominion University since 1996. The method provides a highly sensitive, nonintrusive method of probing gases. Research has concentrated on effectively modeling the higher harmonic shapes that are measured experimentally. Accurately modeling these signals will result in the ability to reliably extract the information contained in transition line shapes.

In order to accurately depict the signals, the theory must be thoroughly understood. This thesis develops the theory of Wavelength Modulation Spectroscopy from two aspects: a direct Fourier series expansion of a time varying intensity profile and through communication theory. In addition, …

High-Efficiency Solar Cells Based On Cu(Inal)Se[Sub 2] Thin Films, S. Marsillac, P. D. Paulson, M. W. Haimbodi, R. W. Birkmire, W. N. Shafarman

Electrical & Computer Engineering Faculty Publications

A Cu(InAl)Se₂solar cell with 16.9% efficiency is demonstrated using a Cu(InAl)Se₂thin film deposited by four-source elemental evaporation and a device structure of glass/Mo/Cu(InAl)Se₂/CdS/ZnO/indium tin oxide/(Ni/Algrid)/MgF₂. A key to high efficiency is improved adhesion between the Cu(InAl)Se₂ and the Mo back contact layer, provided by a 5-nm-thick Ga interlayer, which enabled the Cu(InAl)Se₂ to be deposited at a 530 °C substrate temperature. Film and device properties are compared to Cu(InGa)Se₂ with the same band gap of 1.16 eV. The solar cells have similar behavior, with performance limited by recombination through …

Time-Resolved Photoluminescence Of Inas/Gainsb Quantum Well Lasers, Michael R. Mckay

Theses and Dissertations

In the world of semiconductor photonic device fabrication, one important objective may be to extract as much light as possible from the device. In these devices, photons are created when electrons recombine with holes by transitioning from a high-energy state to a lower one. Unfortunately, electron-hole recombination does not always result in the formation of a photon. There are three basic types of recombination: the first results in the formation of a photon and is called radiative recombination; and the second and third, known as Shockley-Read-Hall and Auger recombination, result in the heating of the device and do not produce …

Single-Sided Noninvasive Inspection Of Multielement Sample Using Fan-Beam Multiplexed Compton Scatter Tomography, Matthew A. Lange

Theses and Dissertations

As aircraft age, corrosion forms upon unobservable surfaces, particularly at the junction of the sheet aluminum and the steel rivets used to attach the sheets to the airframe, degrading the aircraft s airworthiness. Previous research developed a noninvasive technique for the evaluation of the material composition of aluminum surfaces, utilizing the information encoded in the energy spectra of Compton-scattered gamma emissions. The spectra are gathered by a six-element, high purity germanium detector array. A, first principles, deterministic computer code is used to reconstruct a two-dimensional map of the electron density of aluminum samples. Previous efforts, to image pure aluminum samples, …

Textured Mos 2 Thin Films Obtained On Tungsten: Electrical Properties Of The W/Mos 2 Contact, E. Gourmelon, J. C. Bernède, J. Pouzet, S. Marsillac

Electrical & Computer Engineering Faculty Publications

Textured films of molybdenum disulfide have been obtained by solid state reaction between the constituents in thin films form when a (200) oriented tungsten sheet is used as substrate. The crystallites have their c axis perpendicular to the plane of the substrate. The annealing conditions are T=1073K and t=30 min. The films are stoichoimetric and p type. Such highly textured films are achieved without foreign atom addition (Ni, Co...). It appears, as shown by x-ray photoelectron spectroscopy, that a thin WS₂ layer is present at the interface W/MoS₂. The crystallization process is discussed by a …

Selective Cvd Growth Of Diamond Crystals On Tungsten, Charles Randal Cole

Electrical & Computer Engineering Theses & Dissertations

Typical field emitters consist of sharp metal tips which usually have a short life due to erosion and contamination. To improve the performance of regular field emitters, diamond can be placed on the emitter tip. This is done by selectively growing diamond on tungsten tips using chemical vapor deposition (CVD) processing. Diamond exhibits negative electron affinity, so that electrons will be emitted by properly biasing the tip.

To obtain single crystal growth right at the tip, a cantilever controlled nucleation method was developed which worked better than other methods. Surface preparation was also important to the growth process. An oxide …

Experimental Investigation Of Nonlinear Dynamics In Single Mode Semiconductor Laser Diodes With Phase Conjugate Feedback, Gordon T. Hengst

Theses and Dissertations

The semiconductor laser diode offers a unique system to investigate nonlinear dynamics when optical feedback is applied. Although there is extensive research of laser diodes with optical feedback from normal dielectric mirrors, very little has been done experimentally to analyze the effects of degenerate phase conjugate feedback from a BaTiO₃ crystal. This research experimentally investigated the dynamics of a single-mode laser diode with weak phase conjugate feedback using both the self-pumped and double phase conjugate geometries. The experimental results validated a mathematical model which numerically evaluates the Lang-Kobayahsi coupled differential equations. The model simulated the nonlinear behavior of a …

Photoluminescence And Electroluminescence Of Erbium And Neodymium Implanted Semiconductors, James R. Hunter

Theses and Dissertations

Low temperature photoluminescence (PL) and electroluminescence (EL) measurements were used to study the excitation of erbium- and neodymium-implanted GaAs and Al_xGa_1-xAs (x=0. 1, 0.3) pn-junctions. The rare-earth (RE) emissions were investigated as a function of ion dose, aluminum mole fraction, laser excitation power, and applied forward bias voltage for the implanted samples. Low temperature PL was also measured from Er doped silicon grown by the metalorganic chemical vapor-phase deposition (MOCVD) method using various growth parameters.. The MOCVD-grown Si samples were studied as a function of metalorganic source temperature, silane (SiH₄) flow, growth time, and …

Comparison Of Time-Domain Reflectometry Performance Factors For Several Dielectric Geometries: Theory And Experiments, S. V. Maheshwarla, R. Venkatasubramanian, Robert F. Boehm

Electrical & Computer Engineering Faculty Research

We propose three nontraditional dielectric geometries and present an experimental and theoretical analysis and comparison of time domain reflectometry (TDR) performances for them. The traditional geometry (the probes inserted in material of essentially infinite extent) is compared to three nontraditional geometries where the probes are affixed outside of a core sample, inside of a bore, or flat on the surface of a semi-infinite solid. Our derivation relates the velocity of electromagnetic wave propagation to the complex permittivities and permeabilities of the media and the geometry for the three nontraditional configurations. Experimental results for air, styrofoam, dry sand, wet sand of …

Characterization Of Piezoceramic Crosses With Large Range Scanning Capability And Applications For Low Temperature Scanning Tunneling Microscopy, J. A. Helfrich, Shireen Adenwalla, J. B. Ketterson, G. A. Zhitomirsky

Shireen Adenwalla Papers

We have developed a large amplitude piezoceramic scanner which should have numerous applications. Scanning tunneling microscopy (STM) and other scanning probe microscopies predominantly use piezoceramics for the scanning elements. Similarly adaptive optics, high resolution lithography, and micromanipulators are other examples of research which regularly utilize piezoceramic scanners. We present a new geometry for a piezoceramic scanner which allows for both high resolution (~nanometers) and large amplitude (~400 µm) displacements. The cross-shaped geometry makes it possible to produce extremely long pieces with very high tolerances. We have shown its effectiveness by using it as the major component of a low temperature …

The Current Voltage Characteristics Of Electron Beam Controlled Thin Film Diamond Switches, Christopher Anthony Molina

Electrical & Computer Engineering Theses & Dissertations

The dark current of natural diamond thin films and the induced current due to electron-beam irradiation was measured up to a range of 7000Ncm'. The contact material was aluminum, annealed and unannealed. Switching experiments were performed with electron energies ranging from 70keV to 172keV. The switching results obtained are strongly dependent on the biasing polarity, incident electron energy, and whether the contact is blocking or Ohmic in nature. A simple model which takes traps into consideration allows us to explain the various switching responses. The range of electrons which define, in part, the switch mode was measured for one sample …

Light Injection From An Active Cladding To The Core Of A Fiber Optic Fluorosensor, Alvin Leon Bryant

Electrical & Computer Engineering Theses & Dissertations

A fluorosensor works on the basis of light injection from the clad into the core of an optical fiber. The sensitivity of such a sensor depends on the efficiency of light injection. Conditions necessary for a high injection efficiency are experimentally determined. The refractive index difference between the core and the clad,ⁿcore ^-nclad, must be maximized to achieve a high injection efficiency. Since an air clad has the least refractive index, a bare core fiber will have a maximum efficiency. Standard optical fibers used for communication employ a minimum value for ⁿcore ^-nclad, in order …

Processability Of Polythiophene Thin Films By Ultraviolet Photo Bleaching, Derek D. Fletcher

Theses and Dissertations

Materials possessing strong ��⁽³⁾ optical properties such as Polythiophene are sought for the production of optical switches. Polythiophene thin films produced by plasma enhanced CVD show a surface rms roughness of 10^-15 angstroms over single square micron areas which is acceptable for wave guiding in the near IR. This research investigates permanently changing the optical properties of such a thin film by exposure to UV radiation (254 nm, 35 mW/cm²), known as photo bleaching, in hope of creating a refractive index boundary for use in total internal reflection. After 60 minutes exposure the refractive index shows …

Fluorescent Lifetime Measurements Of Rare Earth Elements In Gallium Arsenide, Danny J. Topp

Theses and Dissertations

Lifetime measurements of the excited states of three GaAs semiconductors doped with the rare earth elements Erbium (ER), Praseodymium (Pr) , and Thulium (Tm) has been studied using a pulsed nitrogen laser and germanium detector. The measurements were made with an experimental set up with a system response time of 0.34 micro seconds. A 330 milliwatt nitrogen laser with a wavelength of 3370 angstrums was used to excite transitions of the rare earth elements.

Epr Spectra Of Divalent Manganese In Halide Crystals, Veron Sarkis Sarkissian

Archived Theses and Dissertations

No abstract provided.

Conductivity And Photoconductivity Of As-S-I Glasses, Ahmed Abdel-Hamid El-Difrawi

Archived Theses and Dissertations

No abstract provided.