Engineering Physics Commons^™

Direct Measurement Of Microwave Loss In Nb Films For Superconducting Qubits, B. Abdisatarov, D. Bafia, A. Murthy, G. Eremeev, H. E. Elsayed-Ali, J. Lee, A. Netepenko, C. P. A. Carlos, S. Leith, G. J. Rosaz, A. Romanenko, A. Grassellino

Electrical & Computer Engineering Faculty Publications

Niobium films are a key component in modern two-dimensional superconducting qubits, yet their contribution to the total qubit decay rate is not fully understood. The presence of different layers of materials and interfaces makes it difficult to identify the dominant loss channels in present two-dimensional qubit designs. In this paper, we present the study that directly correlates measurements of RF losses in such films to material parameters by investigating a high-power impulse magnetron sputtered (HiPIMS) film atop a three-dimensional niobium superconducting radio frequency (SRF) resonator. By using a 3D SRF structure, we are able to isolate the niobium film loss …

Transfer Learning For Field Emission Mitigation In Cebaf Srf Cavities, K. Ahammed, J. Li, A. Carpenter, C. Tennant, R. Suleiman

Electrical & Computer Engineering Faculty Publications

The Continuous Electron Beam Accelerator Facility (CEBAF) operates hundreds of superconducting radio frequency (SRF) cavities in its two linear accelerators (linacs). Field emission (FE) is an ongoing operational challenge in higher gradient SRF cavities. FE generates high levels of neutron and gamma radiation leading to damaged accelerator hardware and a radiation hazard environment. During machine development periods, we performed invasive gradient scans to record data capturing the relationship between cavity gradients and radiation levels measured throughout the linacs. However, the field emission environment at CEBAF varies considerably over time as the configuration of the radio-frequency (RF) gradients changes or due …

Effect Of Annealing On Photoluminescence From Defects In Gan, Oleksandr Andrieiev

Theses and Dissertations

Annealing is a critical process in modern GaN technology, essential for achieving p-type conductivity by activating the Mg_Ga acceptor, as first demonstrated by Shuji Nakamura in the early 1990s. Despite the omnipresence of hydrogen as an impurity in GaN crystals, the precise mechanisms governing hydrogen diffusion and acceptor passivation remain only partially understood. The presented research investigates the effects of annealing-induced activation and hydrogen passivation on C and Be acceptors in GaN grown by MOCVD, HVPE, and MBE methods. We explored these effects by using several annealing techniques, gas compositions, and thermal regimes. A transient behavior between the C …

Disaggregating Longer-Term Trends From Seasonal Variations In Measured Pv System Performance, Chibuisi Chinasaokwu Okorieimoh, Brian Norton, Michael Conlon

Articles

Photovoltaic (PV) systems are widely adopted for renewable energy generation, but their performance is influenced by complex interactions between longer-term trends and seasonal variations. This study aims to remove these factors and provide valuable insights for optimising PV system operation. We employ comprehensive datasets of measured PV system performance over five years, focusing on identifying the distinct contributions of longer-term trends and seasonal effects. To achieve this, we develop a novel analytical framework that combines time series and statistical analytical techniques. By applying this framework to the extensive performance data, we successfully break down the overall PV system output into …

Numerical Study Of Owls' Leading-Edge Serrations, Asif Shahriar Nafi, Nikolaos Beratlis, Elias Balaras, Roi Gurka

Physics and Engineering Science

Owls' silent flight is commonly attributed to their special wing morphology combined with wingbeat kinematics. One of these special morphological features is known as the leading-edge serrations: rigid miniature hook-like patterns found at the primaries of the wings' leading-edge. It has been hypothesized that leading-edge serrations function as a passive flow control mechanism, impacting the aerodynamic performance. To elucidate the flow physics associated with owls' leading-edge serrations, we investigate the flow-field characteristic around a barn owl wing with serrated leading-edge geometry positioned at 20° angle of attack for a Reynolds number of 40 000. We use direct numerical simulations, where …

Characterization Of Interlayer Laser Shock Peening During Fused Filament Fabrication Of Polylactic Acid (Pla), Fabien Denise

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

The field of additive manufacturing (AM) has gained a significant amount of popularity due to the increasing need for more sustainable manufacturing techniques and the adaptive development of complex product geometries. The problem is that AM parts routinely exhibit flaws or weaknesses that affect functionality or performance. Over the years, surface treatments have been developed to compensate certain flaws or weaknesses in manufactured products. Combining surface treatments with the modularity of additive manufacturing could lead to more adaptable and creative improvements of product functions in the future. The current work evaluates the feasibility of pursuing a new research axis in …

Impact Of Silicon Ion Irradiation On Aluminum Nitride-Transduced Microelectromechanical Resonators, David D. Lynes, Joshua Young, Eric Lang, Hengky Chandrahalim

Faculty Publications

Microelectromechanical systems (MEMS) resonators use is widespread, from electronic filters and oscillators to physical sensors such as accelerometers and gyroscopes. These devices' ubiquity, small size, and low power consumption make them ideal for use in systems such as CubeSats, micro aerial vehicles, autonomous underwater vehicles, and micro-robots operating in radiation environments. Radiation's interaction with materials manifests as atomic displacement and ionization, resulting in mechanical and electronic property changes, photocurrents, and charge buildup. This study examines silicon (Si) ion irradiation's interaction with piezoelectrically transduced MEMS resonators. Furthermore, the effect of adding a dielectric silicon oxide (SiO₂) thin film is …

Hydroxyapatite-Based Coatings On Silicon Wafers And Printed Zirconia, Antoine Chauvin

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Dental surgery needs a naturally attract implant design that can ensure both osseointegration and soft tissue integration. Hydroxyapatite (HAp), the main mineral constituent of dentine and tooth enamel, is commonly used as a coating component, notably for overlaying titanium– or ceramics–based implants. This thesis aims to investigate the behavior of a HAp-based coating, specifically designed to be compatible with a porous substrate. Coating layers are made by sol–gel dip coating by immersion of porous substrates made by additive manufacturing into solutions of HAp, having been mixed with polyethyleneimine (PEI), to improve the adhesion of HAp on the substrate. First, the …

Directional Microwave Emission From Femtosecond-Laser Illuminated Linear Arrays Of Superconducting Rings, Thomas J. Bullard, Kyle Frische, Charlie Ebbing, Stephen J. Hageman, John Morrison, John Bulmer, Enam A. Chowdury, Michael L. Dexter, Timothy J. Haugan, Anil K. Patnaik

Faculty Publications

We examine the electromagnetic emission from two photo-illuminated linear arrays composed of inductively charged superconducting ring elements. The arrays are illuminated by an ultrafast infrared laser that triggers microwave broadband emission detected in the 1–26 GHz range. Based on constructive interference from the arrays a narrowing of the forward radiation lobe is observed with increasing element count and frequency demonstrating directed GHz emission. Results suggest that higher frequencies and a larger number of elements are achievable leading to a unique pulsed array emitter concept that can span frequencies from the microwave to the terahertz (THz) regime.

Trumpet Directivity From A Rotating Semicircular Array, Samuel D. Bellows, Joseph E. Avila, Timothy W. Leishman

Directivity

The directivity function of a played musical instrument describes the angular dependence of its acoustic radiation and diffraction about the instrument, musician, and musician’s chair. Directivity influences sound in rehearsal, performance, and recording environments and signals in audio systems. Because high-resolution, spherically comprehensive measurements of played musical instruments have been unavailable in the past, the authors have undertaken research to produce and share such data for studies of musical instruments, simulations of acoustical environments, optimizations of microphone placements, and other applications. The authors acquired the data from repeated chromatic scales produced by a trumpet played at mezzo-forte in an anechoic …

The Role Of Leading-Edge Serrations In Controlling The Flow Over Owls’ Wing, Tanner Saussaman, Asif Nafi, David Charland, Hadar Ben-Gida, Roi Gurka

Physics and Engineering Science

We studied the effects of leading-edge serrations on the flow dynamics developed over an owl wing model. Owls are predatory birds. Most owl species are nocturnal, with some active during the day. The nocturnal ones feature stealth capabilities that are partially attributed to their wing microfeatures. One of these microfeatures is small rigid combs (i.e. serrations) aligned at an angle with respect to the incoming flow located at the wings' leading-edge region of the primaries. These serrations are essentially passive flow control devices that enhance some of the owls' flight characteristics, such as aeroacoustics and, potentially, aerodynamics. We performed a …

Analysis Of Coronal Magnetic Field Parameters During X- And M-Class Solar Flares, Seth H. Garland

Theses and Dissertations

Using Non-Linear Force Free Field (NLFFF) extrapolation, 3D magnetic fields were modeled from the 12-minute cadence Helioseismic and Magnetic Imager (HMI) photospheric vector magnetograms, spanning a time period of one hour before through one hour after the start of 18 X-class flares and 12 M-class flares. Several magnetic field parameters were calculated from the modeled fields directly – as well as from the power spectrum of surface maps generated by summing the fields along the vertical axis – for two different regions: areas with photospheric Bz ≥ 300 G (Active Region – AR) and areas above the photosphere with the …

Direct Measurement Of The 114cd(N, Gamma)115cd Cross Section In The 1 Ev To 300 Kev Energy Range, Kofi Tutu Addo Assumin-Gyimah

Theses and Dissertations

The large thermal cross section of cadmium makes it ideal for many practical applications where screening of thermal neutrons is desired. For example, in non-destructive assay techniques, or for astrophysical studies of the s-process. All such applications require precise knowledge of the neutron-capture cross section on cadmium. Although there are some data on neutron-capture cross sections particularly at thermal energies and at energies relevant for astrophysics, there is very little data at most other energies. Further, the evaluated cross sections from the ENDF and JENDL databases disagree at high energies. Therefore, there is a critical need for precise knowledge of …

Electromagnetic Simulations Of The Lansce Chopper Structure, Yusuf Sahin

Electrical and Computer Engineering ETDs

Particle accelerators are important for basic research as well as in applications such as ion implantation and cancer therapy. One important accelerator is the Los Alamos Neutron Science Center (LANSCE) located at Los Alamos National Laboratory (LANL) that primarily produces neutrons for research. The beam chopper simulation described here is a study to provide better modeling of this subsystem of LANSCE. A chopper is a device in which particles are intermittently sliced and directed to a target and/or experiment. The simulations in this thesis are used to analyze the correct operating parameters of the chopper. A good chopper model can …

Study Of Microphonic Effects On The C100 Cryomodule For High Energy Electron Beam Accelerators, Caleb James Hull

Mechanical & Aerospace Engineering Theses & Dissertations

The Continuous Electron Beam Accelerator Facility (CEBAF) at Thomas Jefferson National Laboratory (JLab) is a particle accelerator which can accelerate an electron beam to relativistic speeds and apply the beam onto target samples. The C100 superconducting radio frequency (SRF) cavity is the primary accelerating structure of the C100 cryomodule, one of the many cryomodules which compose the CEBAF linear accelerator. SRF cavities are particularly sensitive to internal and external vibrations that can result in a phenomenon called microphonics which degrade the operational stability of a cryomodule.

The purpose of this thesis is to investigate the significance of mechanical disturbances on …

Experimental And Computational Aerodynamic Studies Of Axially-Oriented Low-Fineness-Ratio Cylinders, Forrest Miller

Mechanical & Aerospace Engineering Theses & Dissertations

For the successful completion of atmospheric entry, descent, and landing (EDL) missions, a body geometry must be selected which provides favorable dynamic aerodynamic properties. The types of experimental facilities capable of collecting information on these properties are limited; however, their numbers are growing thanks to the continued work by the aerodynamics community. NASA Langley Research Center (LaRC) is conducting dynamic aerodynamic testing using a subsonic magnetic suspension and balance system (MSBS), with the end goal of implementing a supersonic MSBS facility at NASA Glenn Research Center. MSBSs are also currently used at the Institute of Fluid Science (IFS) at Tohoku …

Finite Element Analysis Of A Coconut (Cocos Nucifera L.) Climbing Mechanism, Arjay O. Afan, Omar F. Zubia, Adrian A. Borja, Ralph Kristoffer B. Gallegos

The Philippine Agricultural Scientist

A coconut climber mechanism was subjected to Finite Element Analysis (FEA) to improve its overall design and analyze its strength characteristics. The von Mises stress, total deformation, and factor of safety were evaluated using static structural analysis for the seat and pedal assemblies of the mechanism. The design has a minimum yielding factor of safety of 7.03 for the seat assembly and 12.09 for the pedal assembly. If aluminum is used as an alternative to steel, the prototype's weight can be reduced to at least 64.56% without compromising its strength properties. The weight reduction by using aluminum is expected to …

Effective Nanomembranes From Chitosan/Pva Blend Decorated Graphene Oxide With Gum Rosin And Silver Nanoparticles For Removal Of Heavy Metals And Microbes From Water Resources, Mohamed Morsy

Nanotechnology Research Centre

No abstract provided.

Assessment Of Bridge Pier Response To Fire, Vehicle Impact, And Air Blast, Chen Fang, Qusai Alomari, Daniel G. Linzell

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

Highway bridges exposed to intentional or unintentional fire followed by combined vehicle impact and air blast are at risk of significant damage and, possibly, collapse. Limited studies examining the complex effects of these extreme demands on bridge support elements and parametrizing their response and damage are found in the open literature. Research that is presented is part of an ongoing numerical investigation examining round, multi-column, reinforced concrete (RC), bridge pier behavior subject to multi-hazard scenarios involving fire, vehicle impact, and air blast. Detailed nonlinear finite element analysis models of single columns and multi-column piers supported by a pile foundation system …

Machine Learning-Based Data And Model Driven Bayesian Uncertanity Quantification Of Inverse Problems For Suspended Non-Structural System, Zhiyuan Qin

All Dissertations

Inverse problems involve extracting the internal structure of a physical system from noisy measurement data. In many fields, the Bayesian inference is used to address the ill-conditioned nature of the inverse problem by incorporating prior information through an initial distribution. In the nonparametric Bayesian framework, surrogate models such as Gaussian Processes or Deep Neural Networks are used as flexible and effective probabilistic modeling tools to overcome the high-dimensional curse and reduce computational costs. In practical systems and computer models, uncertainties can be addressed through parameter calibration, sensitivity analysis, and uncertainty quantification, leading to improved reliability and robustness of decision and …

Modeling, Simulation And Control Of Microrobots For The Microfactory., Zhong Yang

Electronic Theses and Dissertations

Future assembly technologies will involve higher levels of automation in order to satisfy increased microscale or nanoscale precision requirements. Traditionally, assembly using a top-down robotic approach has been well-studied and applied to the microelectronics and MEMS industries, but less so in nanotechnology. With the boom of nanotechnology since the 1990s, newly designed products with new materials, coatings, and nanoparticles are gradually entering everyone’s lives, while the industry has grown into a billion-dollar volume worldwide. Traditionally, nanotechnology products are assembled using bottom-up methods, such as self-assembly, rather than top-down robotic assembly. This is due to considerations of volume handling of large …

Effect On Focusing Fields By Ferromagnetic Cell Cores In Linear Induction Accelerators, Cooper Guillaume

Senior Honors Theses

In the Los Alamos National Laboratories DARHT facility, there are two perpendicular linear induction accelerators, LIAs. The LIAs’ solenoids produce magnetic fields which focus the electron beam. Simultaneously, the accelerating pulse creates a magnetic field. These two field intensities act upon a ferromagnetic material in the cells to enhance magnetic flux density. Due to the nonlinearity of the material, this flux density will reach a saturation point. In turn, the magnetic field intensity of the axial solenoidal magnetic field will be affected and slightly altered. The width of the electron beam will increase, causing a decrease in effectiveness. Through simulation, …

Analysis And Application Of Finite Element And High-Order Finite Difference Methods For Maxwell’S Equations In Complex Media, Li Zhu

UNLV Theses, Dissertations, Professional Papers, and Capstones

The Perfectly Matched Layer (PML) technique is an effective tool introduced by B´erenger [13] to reduce the unbounded wave propagation problem to a bounded domain problem. This dissertation focuses on two different PML models and their applications to wave propagation problems with Maxwell’s equation in complex media. We investigate these models using two popular numerical methods: the Finite Difference Method (FDM) in Chapters 2 and 3, and the Finite Element Method (FEM) in Chapters 4 and 5.In Chapter 2, we focus on analyzing the stability of a PML developed by B’ecache et al. [10] for simulating wave propagation in the …

Towards An Understanding Of The Thermodynamic Properties Of Crtao4: A Computational Perspective, Tanner B. Gordon

Theses and Dissertations

Materials that can withstand higher temperatures are paramount for next-generation aircraft design. Hypersonic capabilities and jet-turbine engines operate in extreme environments. Choosing materials that have high thermal stability and oxidation resistance for these applications can increase engine efficiency, reduce size, weight and power (SWaP), and increase the maneuverability of the aircraft. The mixed oxide CrTaO₄ has been experimentally observed to significantly contribute to oxidation resistance at high temperatures. However, and despite its significance, its properties remain largely unknown. This work explores the thermal properties of this material from a multi-scale approach, by obtaining an accurate description of the thermodynamics …

Numerical Study Of Owls’ Leading-Edge Serrations, Asif Shahriar Nafi

Electronic Theses and Dissertations

The silent flight ability of owls is often attributed to their unique wing morphology and its interaction with their wingbeat kinematics. Among these distinctive morphological features, leading-edge serrations stand out – these are rigid, miniature, hook-like patterns located at the leading edge of the primary feathers of their wings. It had been hypothesized that these leading-edge serrations serve as a passive flow control mechanism, influencing the aerodynamic performance and potentially affecting the boundary layer development over the wing, subsequently influencing wake flow dynamics. Despite being the subject of research spanning multiple decades, a consensus regarding the aerodynamic mechanisms underpinning owls’ …

Gamelan Gong Directivity Dataset, Samuel D. Bellows, Dallin T. Harwood, Kent L. Gee, Micah R. Shepherd

Directivity

No abstract provided.

Development Of Interatomic Potential Of High Entropy Diborides With Artificial Intelligence Approach To Simulate The Thermo-Mechanical Properties, Nur Aziz Octoviawan

Graduate Theses/Dissertations

The interatomic potentials designed for binary/high entropy diborides and ultra-high temperature composites (UHTC) have been developed through the implementation of deep neural network (DNN) algorithms. These algorithms employed two different approaches and corresponding codes; 1) strictly local & invariant scalar-based descriptors as implemented in the DEEPMD code and 2) equivariant tensor-based descriptors as included in the ALLEGRO code. The samples for training and validation sets of the forces, energy, and virial data were obtained from the ab-initio molecular dynamics (AIMD) simulations and Density Functional Theory (DFT) calculations, including the simulation data from the ultra-high temperature region (> 2000K). The study …

Experimental Uncertainty In Measurements Of Violin Impulse Response, Andrew Piacsek, Seth Lowery

All Faculty Scholarship for the College of the Sciences

Experiments that investigate how an individual musical instrument changes in response to subtle alterations must contend with measurement uncertainty, which typically arises from inconsistencies in the measurement setup. We quantify uncertainty in violin response measurements by measuring bridge admittance and radiatively of a single instrument that is repeatedly removed and reinstalled in our measurement apparatus. From this set of baseline measurements, we calculate the average and standard deviation of admittance and radiativity. The amount of variation observed in the baseline data is compared to the change in bridge admittance that occurred over several days due to a large and abrupt …

Analytical Heat Transfer Modeling Of The Microwave Heating Process: A Focus On Carbon Black, Craig Offutt

Graduate Theses, Dissertations, and Problem Reports (ETD)

Electronic waste (e-waste) has become a significant environmental issue due to the rapid advancement of technology, increasing demand for electronic devices, and shorter lifespan of electronics. One critical step in processing the e-waste involves ball milling as a means of preparing the recycling e-waste for the recovery of critical materials. Ball milling is a technique that involves the mechanical crushing and grinding of electronic waste to reduce its size and improve its reactivity during recovery. Our focused recovery technique is based on a microwave recovery technique of these critical materials from e-waste. The size and distribution of the e-waste with …

Superheating Field In Superconductors With Nanostructured Surfaces, W. P. M. R. Pathirana, A. Gurevich

Physics Faculty Publications

We report calculations of a dc superheating field H_sh in superconductors with nanostructured surfaces. Numerical simulations of the Ginzburg-Landau (GL) equations were performed for a superconductor with an inhomogeneous impurity concentration, a thin superconducting layer on top of another superconductor, and superconductor-insulator-superconductor (S-I-S) multilayers.The superheating field was calculated taking into account the instability of the Meissner state with a nonzero wavelength along the surface, which is essential for realistic values of the GL parameter κ. Simulations were done for the materials parameters of Nb and Nb₃Sn at different values of κ and the mean free paths. We …