Open Access. Powered by Scholars. Published by Universities.®

Engineering Physics Commons

Open Access. Powered by Scholars. Published by Universities.®

Articles 1 - 20 of 20

Full-Text Articles in Engineering Physics

Photoluminescence Of Beryllium-Related Defects In Gallium Nitride, Mykhailo Vorobiov, Mykhailo Vorobiov Jan 2024

Photoluminescence Of Beryllium-Related Defects In Gallium Nitride, Mykhailo Vorobiov, Mykhailo Vorobiov

Theses and Dissertations

This study explores the potential of beryllium (Be) as an alternative dopant to magnesium (Mg) for achieving higher hole concentrations in gallium nitride (GaN). Despite Mg prominence as an acceptor in optoelectronic and high-power devices, its deep acceptor level at 0.22 eV above the valence band limits its effectiveness. By examining Be, this research aims to pave the way to overcoming these limitations and extend the findings to aluminum nitride and aluminum gallium nitride (AlGaN) alloy. Key contributions of this work include. i)Identification of three Be-related luminescence bands in GaN through photoluminescence spectroscopy, improving the understanding needed for further material …


Direct Measurement Of The 114cd(��, ��)115cd Cross Section In The 1 Ev To 300 Kev Energy Range, Kofi Tutu Addo Assumin-Gyimah Aug 2023

Direct Measurement Of The 114cd(��, ��)115cd Cross Section In The 1 Ev To 300 Kev Energy Range, Kofi Tutu Addo Assumin-Gyimah

Theses and Dissertations

The large thermal cross section of cadmium makes it ideal for many practical applications where screening of thermal neutrons is desired. For example, in non-destructive assay techniques, or for astrophysical studies of the s-process. All such applications require precise knowledge of the neutron-capture cross section on cadmium. Although there are some data on neutron-capture cross sections particularly at thermal energies and at energies relevant for astrophysics, there is very little data at most other energies. Further, the evaluated cross sections from the ENDF and JENDL databases disagree at high energies. Therefore, there is a critical need for precise knowledge of …


Mechanisms Of Emulsion Destabilization: An Investigation Of Surfactant, Stabilizer, And Detergent Based Formulations Using Diffusing Wave Spectroscopy, Jordan N. Nowaczyk Jan 2023

Mechanisms Of Emulsion Destabilization: An Investigation Of Surfactant, Stabilizer, And Detergent Based Formulations Using Diffusing Wave Spectroscopy, Jordan N. Nowaczyk

Theses and Dissertations

Conventional approaches for studying emulsions, such as microscopy and macroscopic phase tracking, present challenges when it comes to establishing detailed mechanistic descriptions of the impact of emulsifier and stabilizer additives. Additionally, while a combination of sizing methods and macroscopic phase tracking can provide insights into droplet size changes and concentration, the use of multiple measurements can be cumbersome and error-prone. It is the focus of this work, to present a new method for studying water in oil (W/O) emulsions that involves using diffusing wave spectroscopy (DWS) to examine the impact of three different surface stabilizing additives at varying concentrations. By …


Full Pattern Analysis And Comparison Of The Center Fed And Offset Fed Cassegrain Antennas With Large Focal Length To Diameter Ratios For High Power Microwave Transmission, Derek W. Mantzke Jun 2022

Full Pattern Analysis And Comparison Of The Center Fed And Offset Fed Cassegrain Antennas With Large Focal Length To Diameter Ratios For High Power Microwave Transmission, Derek W. Mantzke

Theses and Dissertations

High power microwaves (HPM) have been a topic of research since the Cold War era. This paper will present a comparison between two Cassegrain-type antennas: the axially, or center fed, and the offset fed. Specifically, the 10 GHz operating frequency will be investigated with large focal length to diameter () ratios. Beam patterns which encompass the entire radiation pattern will be included for data validation and optimization. The simulations will follow a design of experiments factorial model to ensure all possible combinations of prescribed parameters are included, including an analysis of variance (ANOVA) study to find parameter influence on the …


Targeted Germanium Ion Irradiation Of Aluminum Gallium Nitride/Gallium Nitride High Electron Mobility Transistors, Melanie E. Mace Aug 2019

Targeted Germanium Ion Irradiation Of Aluminum Gallium Nitride/Gallium Nitride High Electron Mobility Transistors, Melanie E. Mace

Theses and Dissertations

Microscale beams of germanium ions were used to target different locations of aluminum galliumnitride/gallium nitride (AlGaN/GaN) high electron mobility transistors (HEMTs) to determine location dependent radiation effects. 1.7 MeV Ge ions were targeted at the gap between the gate and the drain to observe displacement damage effects while 47 MeV Ge ions were targeted at the gate to observe ionization damage effects. Electrical data was taken pre, during, and post irradiation. To separate transient from permanent degradation, the devices were characterized after a room temperature anneal for at least 30 days. Optical images were also analyzed pre and post irradiation. …


Straintronic Nanomagnetic Devices For Non-Boolean Computing, Md Ahsanul Abeed Jan 2019

Straintronic Nanomagnetic Devices For Non-Boolean Computing, Md Ahsanul Abeed

Theses and Dissertations

Nanomagnetic devices have been projected as an alternative to transistor-based switching devices due to their non-volatility and potentially superior energy-efficiency. The energy efficiency is enhanced by the use of straintronics which involves the application of a voltage to a piezoelectric layer to generate a strain which is ultimately transferred to an elastically coupled magnetostrictive nanomaget, causing magnetization rotation. The low energy dissipation and non-volatility characteristics make straintronic nanomagnets very attractive for both Boolean and non-Boolean computing applications. There was relatively little research on straintronic switching in devices built with real nanomagnets that invariably have defects and imperfections, or their adaptation …


Improving Detection Of Dim Targets: Optimization Of A Moment-Based Detection Algorithm, Shannon R. Young Dec 2018

Improving Detection Of Dim Targets: Optimization Of A Moment-Based Detection Algorithm, Shannon R. Young

Theses and Dissertations

Wide area motion imagery (WAMI) sensor technology is advancing rapidly. Increases in frame rates and detector array sizes have led to a dramatic increase in the volume of data that can be acquired. Without a corresponding increase in analytical manpower, much of these data remain underutilized. This creates a need for fast, automated, and robust methods for detecting dim, moving signals of interest. Current approaches fall into two categories: detect-before-track (DBT) and track-before-detect (TBD) methods. The DBT methods use thresholding to reduce the quantity of data to be processed, making real time implementation practical but at the cost of the …


Fabricating Superhydrophobic And Superoleophobic Surfaces With Multiscale Roughness Using Airbrush And Electrospray, Karam N. Almilaji Jan 2016

Fabricating Superhydrophobic And Superoleophobic Surfaces With Multiscale Roughness Using Airbrush And Electrospray, Karam N. Almilaji

Theses and Dissertations

Examples of superhydrophobic surfaces found in nature such as self-cleaning property of lotus leaf and walking on water ability of water strider have led to an extensive investigation in this area over the past few decades. When a water droplet rests on a textured surface, it may either form a liquid-solid-vapor composite interface by which the liquid droplet partially sits on air pockets or it may wet the surface in which the water replaces the trapped air depending on the surface roughness and the surface chemistry. Super water repellent surfaces have numerous applications in our daily life such as drag …


Beyond Conventional C-Plane Gan-Based Light Emitting Diodes: A Systematic Exploration Of Leds On Semi-Polar Orientations, Morteza Monavarian Jan 2016

Beyond Conventional C-Plane Gan-Based Light Emitting Diodes: A Systematic Exploration Of Leds On Semi-Polar Orientations, Morteza Monavarian

Theses and Dissertations

Despite enormous efforts and investments, the efficiency of InGaN-based green and yellow-green light emitters remains relatively low, and that limits progress in developing full color display, laser diodes, and bright light sources for general lighting. The low efficiency of light emitting devices in the green-to-yellow spectral range, also known as the “Green Gap”, is considered a global concern in the LED industry. The polar c-plane orientation of GaN, which is the mainstay in the LED industry, suffers from polarization-induced separation of electrons and hole wavefunctions (also known as the “quantum confined Stark effect”) and low indium incorporation efficiency that …


Electrical Characterization Of Spherical Copper Oxide Memristive Array Sensors, James P. Orta Mar 2014

Electrical Characterization Of Spherical Copper Oxide Memristive Array Sensors, James P. Orta

Theses and Dissertations

A new System Protection (SP) technology is explored by using electrical and mechanical interference-sensing devices that are implemented with granular memristive material. The granular materials consist of oxide-coated copper spheres with radii of about 700 µm that are placed in contact to produce thin oxide junctions which exhibit memristive behavior. Processes for etching, which compared acetic acid and nitric acid etches, and thermal oxidation at 100°C are performed and compared to produce copper spheres with a copper oxide layer over the sphere surface. Oxidized copper spheres are tested as sensor arrays by loading into a capillary tube in an aligned …


Rubidium Recycling In A High Intensity Short Duration Pulsed Alkali Laser, Wooddy S. Miller Mar 2010

Rubidium Recycling In A High Intensity Short Duration Pulsed Alkali Laser, Wooddy S. Miller

Theses and Dissertations

Laser induced fluorescence was used to study how pump pulse duration and alkali recycle time effects maximum power output in a Diode Pumped Alkali Laser (DPAL) system. A high intensity short pulsed pump source was used to excited rubidium atoms inside a DPAL-type laser. The maximum output power of the laser showed a strong dependence upon the temporal width of the pump pulse in addition to the input pump intensity. A linear relationship was observed between the maximum output power and the pulse width due to the effective lifetime of the excited state, defined as the time it takes for …


Electron Multipactor: Theory Review, Comparison And Modeling Of Mitigation Techniques In Icepic, Neil G. Rogers Mar 2009

Electron Multipactor: Theory Review, Comparison And Modeling Of Mitigation Techniques In Icepic, Neil G. Rogers

Theses and Dissertations

Mitigation approaches for single surface multipactor at dielectric windows are investigated using Particle-In-Cell (PIC) simulations. Initially baseline susceptibility diagrams are constructed analytically and compared with self-consistent, dynamic system trajectories. The power deposited on the surface of a dielectric window in an HPM system is considered using three different methods and the results of PIC simulations. Geometric mitigation is then considered by varying the window orientation with respect to the HPM electric held. Small angular deviations, less than 20 degrees, from the nominal case of normal incidence show dramatic changes in the susceptibility diagram. A materials approach to mitigation is then …


Parallel Fast Multipole Method For Molecular Dynamics, Reid G. Ormseth Jun 2007

Parallel Fast Multipole Method For Molecular Dynamics, Reid G. Ormseth

Theses and Dissertations

We report on a parallel version of the Fast Multipole Method (FMM) implemented in the classical molecular dynamics code, NAMD (Not Another Molecular Dynamics program). This novel implementation of FMM aims to minimize interprocessor communication through the modification of the FMM grid to match the hybrid force and spatial decomposition scheme already present in NAMD. This new implementation has the benefit of replacing all-to-all communications broadcasts with direct communications between nearest neighbors. This results in a significant reduction in the amount of communication compared to earlier attempts to integrate FMM into common molecular dynamics programs. The early performance of FMM …


Daytime Detection Of Space Objects, Alistair D. Funge Mar 2005

Daytime Detection Of Space Objects, Alistair D. Funge

Theses and Dissertations

Space Situational Awareness (SSA) requires repeated object updates for orbit accuracy. Detection of unknown objects is critical. A daytime model was developed that evaluated sun flares and assessed thermal emissions from space objects. Iridium satellites generate predictable sun glints. These were used as a model baseline for daytime detections. Flares and space object thermal emissions were examined for daytime detection. A variety of geometric, material and atmospheric characteristics affected this daytime detection capability. In a photon noise limited mode, simulated Iridium flares were detected. The peak Signal-to- Noise Ratios (SNR) were 6.05e18, 9.63e5, and 1.65e7 for the nighttime, daytime and …


Time-Resolved Photoluminescence Of Inas/Gainsb Quantum Well Lasers, Michael R. Mckay Jun 2001

Time-Resolved Photoluminescence Of Inas/Gainsb Quantum Well Lasers, Michael R. Mckay

Theses and Dissertations

In the world of semiconductor photonic device fabrication, one important objective may be to extract as much light as possible from the device. In these devices, photons are created when electrons recombine with holes by transitioning from a high-energy state to a lower one. Unfortunately, electron-hole recombination does not always result in the formation of a photon. There are three basic types of recombination: the first results in the formation of a photon and is called radiative recombination; and the second and third, known as Shockley-Read-Hall and Auger recombination, result in the heating of the device and do not produce …


Single-Sided Noninvasive Inspection Of Multielement Sample Using Fan-Beam Multiplexed Compton Scatter Tomography, Matthew A. Lange Jun 2001

Single-Sided Noninvasive Inspection Of Multielement Sample Using Fan-Beam Multiplexed Compton Scatter Tomography, Matthew A. Lange

Theses and Dissertations

As aircraft age, corrosion forms upon unobservable surfaces, particularly at the junction of the sheet aluminum and the steel rivets used to attach the sheets to the airframe, degrading the aircraft s airworthiness. Previous research developed a noninvasive technique for the evaluation of the material composition of aluminum surfaces, utilizing the information encoded in the energy spectra of Compton-scattered gamma emissions. The spectra are gathered by a six-element, high purity germanium detector array. A, first principles, deterministic computer code is used to reconstruct a two-dimensional map of the electron density of aluminum samples. Previous efforts, to image pure aluminum samples, …


Space Charge Structure Of A Glow Discharge In The Presence Of A Longitudinal Inhomogeneity, Frank A. Tersigni Mar 1999

Space Charge Structure Of A Glow Discharge In The Presence Of A Longitudinal Inhomogeneity, Frank A. Tersigni

Theses and Dissertations

A survey of space charge structures arising due to inhomogeneities in glow discharges was conducted. Space charge structures associated with tube geometries, the cathode sheath, striations, and shockwaves were examined. Space charge effects on the Electron Energy Distribution Function (EEDF) were explored for a geometric inhomogeneity using an approximate nonlocal solution to the one dimensional Boltzmann equation after Godyak. The approximate solution partially captured qualitative aspects of space charge effects on the EEDF. Simplification of collisional effects and adaptation of an approximate electric field restricted quantitative comparisons with experimental data. It is recommended that any future analysis of space charge …


Experimental Investigation Of Nonlinear Dynamics In Single Mode Semiconductor Laser Diodes With Phase Conjugate Feedback, Gordon T. Hengst Aug 1997

Experimental Investigation Of Nonlinear Dynamics In Single Mode Semiconductor Laser Diodes With Phase Conjugate Feedback, Gordon T. Hengst

Theses and Dissertations

The semiconductor laser diode offers a unique system to investigate nonlinear dynamics when optical feedback is applied. Although there is extensive research of laser diodes with optical feedback from normal dielectric mirrors, very little has been done experimentally to analyze the effects of degenerate phase conjugate feedback from a BaTiO3 crystal. This research experimentally investigated the dynamics of a single-mode laser diode with weak phase conjugate feedback using both the self-pumped and double phase conjugate geometries. The experimental results validated a mathematical model which numerically evaluates the Lang-Kobayahsi coupled differential equations. The model simulated the nonlinear behavior of a …


Photoluminescence And Electroluminescence Of Erbium And Neodymium Implanted Semiconductors, James R. Hunter Dec 1995

Photoluminescence And Electroluminescence Of Erbium And Neodymium Implanted Semiconductors, James R. Hunter

Theses and Dissertations

Low temperature photoluminescence (PL) and electroluminescence (EL) measurements were used to study the excitation of erbium- and neodymium-implanted GaAs and AlxGa1-xAs (x=0. 1, 0.3) pn-junctions. The rare-earth (RE) emissions were investigated as a function of ion dose, aluminum mole fraction, laser excitation power, and applied forward bias voltage for the implanted samples. Low temperature PL was also measured from Er doped silicon grown by the metalorganic chemical vapor-phase deposition (MOCVD) method using various growth parameters.. The MOCVD-grown Si samples were studied as a function of metalorganic source temperature, silane (SiH4) flow, growth time, and …


Multispectral Detection Of Ground Targets In Highly Correlated Backgrounds, Jason E. Thomas Dec 1994

Multispectral Detection Of Ground Targets In Highly Correlated Backgrounds, Jason E. Thomas

Theses and Dissertations

Multispectral detection methods attempt to discriminate targets in a dominant clutter background using multiple images of the same real-world scene taken in different narrow spectral bands in the infrared. Detection is possible due to the empirically observed phenomenon that the radiance of man-made objects, such as a tank or truck, often lies off the main spectral correlation axis of that of natural backgrounds. Radiometric measurements of several vehicles and a tree canopy background taken over three days in June. 1994 were used to examine the factors affecting multispectral detection. Results clearly showed that the processes which provide for higher spectral …