Engineering Physics Commons^™

Reactions Of Oxygen And Nitric Oxide In A Microhollow Electrode Discharge, Joseph L. Desormeaux Jr.

Electrical & Computer Engineering Theses & Dissertations

Microhollow electrode discharges have been developed and researched in the Physical Electronics Research Institute Laboratories. This discharge typically operates in direct current mode. Microhollow electrode discharges are non-thermal discharges that produce electrons with energies greater than 10 electron volts. Passing gas mixtures through non-equilibrium discharges invokes excitation or dissociation of gas molecules.

The scope of my research was to study the effect of the discharge on the chemistry of two gases, oxygen and nitric oxide in nitrogen mixture. Initial experiments were performed in an effort to produce ozone near atmospheric pressure. This seemed possible since the discharge has a high-energy …

Coupled Electrodynamic-Monte Carlo Simulations Of Nanoscale Gaas Terahertz Optical Mixers, Jiang Li

Electrical & Computer Engineering Theses & Dissertations

The concept of mixing or heterodyning has traditionally been used for microwaves and for radio frequency communications. However, the concept can easily be extended into the optical frequency regime. By doing so, the photomixing process can serve as a very versatile tool for both the generation of ultrahigh frequency (terahertz) and the detection of weak optical signals.

The aim of this thesis is to perform a theoretical study of the photomixing process inside GaAs devices as the non-linear elements. A coupled approach which combines the Monte Carlo simulation scheme for the carrier transport, with Maxwell's equation for the electrodynamics, has …

Material Evaluation By Pulsed Diode Laser Optoacoustics, Xiaodong Xu

Electrical & Computer Engineering Theses & Dissertations

Pulsed diode laser optoacoustic diagnostics were carried out to characterize solid sample materials. The apparatus developed is compact, portable, cost-effective and therefore very promising for both industrial as well as laboratory applications. To our knowledge, this is the first time that optoacoustic characterization and measurement have been performed with a diode laser. The method was successfully applied to measure the thickness of a multilayer structure non-intrusively. Internal cracks of the material were detected by this technique.

A theory for optoacoustic signal generation, propagation and detection is given. A numerical analysis technique is developed to solve for the expected signal. In …

Atomic Hydrogen Cleaning Of Inp(100) For Preparation Of A Negative Electron Affinity Photocathode, K. A. Elamrawi, M. A. Hafez, H. E. Elsayed-Ali

Electrical & Computer Engineering Faculty Publications

Atomic hydrogen cleaning is used to clean InP(100) negative electron affinity photocathodes. Reflection high-energy electron diffraction patterns of reconstructed, phosphorus-stabilized, InP(100) surfaces are obtained after cleaning at ∼400 °C. These surfaces produce high quantum efficiency photocathodes (∼8.5%), in response to 632.8 nm light. Without atomic hydrogen cleaning, activation of InP to negative electron affinity requires heating to ∼530 °C. At this high temperature, phosphorus evaporates preferentially and a rough surface is obtained. These surfaces produce low quantum efficiency photocathodes (∼0.1%). The use of reflection high-energy electron diffraction to measure the thickness of the deposited cesium layer during activation by correlating …

A Novel Laboratory Course On Advanced Chemical Engineering Experiments, Jochen A. Lauterbach, S. White, X. Lui, G. M. Bodner, W. N. Delgass

Faculty Publications

The chemical engineering curriculum in the United States has trained generations of technical experts who have successfully optimized chemical processes and products once they entered the chemical industry. The U.S. chemical industry, however, has entered a critical stage in which it must be able to create new and differentiated value through technical innovations that arc essential for long-term survival. This innovation process will require new skills that go far beyond the traditional expertise for the optimization of tasks possessed by young chemical engineers. The innovators must be able to identify new opportunities, explore the boundaries of technology, evaluate critical issues, …

Selective Cvd Growth Of Diamond Crystals On Tungsten, Charles Randal Cole

Electrical & Computer Engineering Theses & Dissertations

Typical field emitters consist of sharp metal tips which usually have a short life due to erosion and contamination. To improve the performance of regular field emitters, diamond can be placed on the emitter tip. This is done by selectively growing diamond on tungsten tips using chemical vapor deposition (CVD) processing. Diamond exhibits negative electron affinity, so that electrons will be emitted by properly biasing the tip.

To obtain single crystal growth right at the tip, a cantilever controlled nucleation method was developed which worked better than other methods. Surface preparation was also important to the growth process. An oxide …

Experimental Investigation Of Nonlinear Dynamics In Single Mode Semiconductor Laser Diodes With Phase Conjugate Feedback, Gordon T. Hengst

Theses and Dissertations

The semiconductor laser diode offers a unique system to investigate nonlinear dynamics when optical feedback is applied. Although there is extensive research of laser diodes with optical feedback from normal dielectric mirrors, very little has been done experimentally to analyze the effects of degenerate phase conjugate feedback from a BaTiO₃ crystal. This research experimentally investigated the dynamics of a single-mode laser diode with weak phase conjugate feedback using both the self-pumped and double phase conjugate geometries. The experimental results validated a mathematical model which numerically evaluates the Lang-Kobayahsi coupled differential equations. The model simulated the nonlinear behavior of a …

High Resolution Wavelength Modulation Spectroscopy For Precise Gaseous Characterization, Audra Michiele Bullock

Electrical & Computer Engineering Theses & Dissertations

Wavelength modulation spectroscopy is a highly sensitive, non-intrusive technique for probing gaseous species. Parameters such as velocity, density, and temperature can be measured and monitored with a high degree of precision. In addition, with the use of this technique multiple molecular species may be identified with a single laser probe. This measurement technique utilizes the well-known principles of modulation absorption spectroscopy in a novel way.

The research focuses on harmonic detection and the advantages gained by performing detection at higher harmonics, those greater than the commonly used second harmonic. We show that there is an increase in the sensitivity to …

Two-Dimensional Drift-Diffusion Simulations Of Silicon Avalanche Shaper (Sas) Devices For High Power Applications, Hamid Jalali

Electrical & Computer Engineering Theses & Dissertations

Silicon Avalanche Shaper devices have been projected as being important components of an inexpensive, semiconductor-based technology for high power switching applications. The primary advantage of this technology is that it is based on Silicon material which is easy to fabricate and has a well established processing technology. Unlike other high power technologies, the SAS devices do not rely on external optical triggering which eliminates the need for lasers and related optical circuitry.

The SAS based high power switching technology has been pioneered and tested by a Russian group. Though preliminary results have been very encouraging, the device reliability and its …

Electron Beam Emission From A Ferroelectric Cathode, Crystal Briana Garland

Electrical & Computer Engineering Theses & Dissertations

The electron beam emission from a LTZ-2 (lead titanate-zirconate) ferroelectric cathode was characterized. The purpose was to determine the operation range for this type of electron emitter. The experimental apparatus consisted of a high voltage driving circuit with a charging voltage up to 30kV. A solid-state SCR switch is used to generate the high voltage pulse which induces a polarization change. Current densities on the order of 80A/cm² 30kV were achieved. The electron beam profile is Guassian. At long anode-cathode distances the measured current densities were found to be above Child-Langmuir space charge limits. The large current densities and …

Frequency Response Enhancement Of A Flow Sensor Using Diamond Thin Films Synthesized By Plasma Cvd, John Curren Hagwood

Electrical & Computer Engineering Theses & Dissertations

Theoretical modeling conducted previously in our Microelectronics Laboratory has shown that a layer of diamond film inserted between a metal film and a substrate will enhance the frequency response of a conventional thin film flow sensor. This thesis involved fabricating and testing a conventional thin film sensor of nickel on quartz (Ni/Q) and a diamond enhanced sensor (Ni/D/Q) for comparative frequency response analysis to validate the theory. Diamond films were grown onto quartz substrates using a microwave plasma enhanced chemical vapor deposition process. Conditions were established to synthesize continuous diamond films on quartz substrates. These films were characterized by scanning …

Wavelength Modulation Spectroscopy With Diode Lasers, Ying Lu

Electrical & Computer Engineering Theses & Dissertations

Wavelength Modulation Spectroscopy is a non-intrusive technique which enables several parameters such as concentration, velocity, and temperature of a target specie to be measured. The method involves a modulation of a probe laser beam and detection at the fundamental, or any harmonic frequency, by a phase-sensitive apparatus. The theory of wavelength modulation is discussed. Effects of the finite value of the wavelength modulation index, together with the effects of any residual amplitude modulation that often occurs simultaneously in a diode laser, are included. It is shown that there are several advantages in using detection harmonics orders greater than the second. …

Photoluminescence And Electroluminescence Of Erbium And Neodymium Implanted Semiconductors, James R. Hunter

Theses and Dissertations

Low temperature photoluminescence (PL) and electroluminescence (EL) measurements were used to study the excitation of erbium- and neodymium-implanted GaAs and Al_xGa_1-xAs (x=0. 1, 0.3) pn-junctions. The rare-earth (RE) emissions were investigated as a function of ion dose, aluminum mole fraction, laser excitation power, and applied forward bias voltage for the implanted samples. Low temperature PL was also measured from Er doped silicon grown by the metalorganic chemical vapor-phase deposition (MOCVD) method using various growth parameters.. The MOCVD-grown Si samples were studied as a function of metalorganic source temperature, silane (SiH₄) flow, growth time, and …

Comparison Of Time-Domain Reflectometry Performance Factors For Several Dielectric Geometries: Theory And Experiments, S. V. Maheshwarla, R. Venkatasubramanian, Robert F. Boehm

Electrical & Computer Engineering Faculty Research

We propose three nontraditional dielectric geometries and present an experimental and theoretical analysis and comparison of time domain reflectometry (TDR) performances for them. The traditional geometry (the probes inserted in material of essentially infinite extent) is compared to three nontraditional geometries where the probes are affixed outside of a core sample, inside of a bore, or flat on the surface of a semi-infinite solid. Our derivation relates the velocity of electromagnetic wave propagation to the complex permittivities and permeabilities of the media and the geometry for the three nontraditional configurations. Experimental results for air, styrofoam, dry sand, wet sand of …

Supralinear Photoconductivity Of Copper Doped Semi-Insulating Gallium Arsenide, K. H. Schoenbach, R. P. Joshi, F. Peterkin, R. L. Druce

Bioelectrics Publications

We report on the intensity dependent supralinear photoconductivity in GaAs:Si:Cu material. The results of our measurements show that the effective carrier lifetime can change over two orders of magnitude with variations in the intensity of the optical excitation. A threshold intensity level has been observed and can be related to the occupancy of the deep copper level. Numerical simulations have also been carried out to analyze the trapping dynamics. The intensity dependent lifetimes obtained from the simulations match the experimental data very well. Finally, based on the nonlinear intensity dependence of the effective lifetimes, a possible low‐energy phototransistor application for …

Characterization Of Piezoceramic Crosses With Large Range Scanning Capability And Applications For Low Temperature Scanning Tunneling Microscopy, J. A. Helfrich, Shireen Adenwalla, J. B. Ketterson, G. A. Zhitomirsky

Shireen Adenwalla Papers

We have developed a large amplitude piezoceramic scanner which should have numerous applications. Scanning tunneling microscopy (STM) and other scanning probe microscopies predominantly use piezoceramics for the scanning elements. Similarly adaptive optics, high resolution lithography, and micromanipulators are other examples of research which regularly utilize piezoceramic scanners. We present a new geometry for a piezoceramic scanner which allows for both high resolution (~nanometers) and large amplitude (~400 µm) displacements. The cross-shaped geometry makes it possible to produce extremely long pieces with very high tolerances. We have shown its effectiveness by using it as the major component of a low temperature …

Multispectral Detection Of Ground Targets In Highly Correlated Backgrounds, Jason E. Thomas

Theses and Dissertations

Multispectral detection methods attempt to discriminate targets in a dominant clutter background using multiple images of the same real-world scene taken in different narrow spectral bands in the infrared. Detection is possible due to the empirically observed phenomenon that the radiance of man-made objects, such as a tank or truck, often lies off the main spectral correlation axis of that of natural backgrounds. Radiometric measurements of several vehicles and a tree canopy background taken over three days in June. 1994 were used to examine the factors affecting multispectral detection. Results clearly showed that the processes which provide for higher spectral …

The Current Voltage Characteristics Of Electron Beam Controlled Thin Film Diamond Switches, Christopher Anthony Molina

Electrical & Computer Engineering Theses & Dissertations

The dark current of natural diamond thin films and the induced current due to electron-beam irradiation was measured up to a range of 7000Ncm'. The contact material was aluminum, annealed and unannealed. Switching experiments were performed with electron energies ranging from 70keV to 172keV. The switching results obtained are strongly dependent on the biasing polarity, incident electron energy, and whether the contact is blocking or Ohmic in nature. A simple model which takes traps into consideration allows us to explain the various switching responses. The range of electrons which define, in part, the switch mode was measured for one sample …

Derivative Absorption Spectroscopy With Tunable Laser Diodes, Andrew D. Jackson

Electrical & Computer Engineering Theses & Dissertations

Derivative Absorption Spectroscopy using tunable diode lasers provides a non­ intrusive, sensitive, and convenient method for monitoring gaseous characteristics such as concentration, temperature, and flow velocity. In addition, the specie type can be identified, and if the equation of state is known, pressure may be deduced.

This technique was used on molecular oxygen, in which the rovibronic transitions of the A-band ( b ¹ ∑_g ⁺ ← X ³ ∑g ^- ; v^II = O, v^I = O) were probed. Phase sensitive detection with a lock-in amplifier provides the flexibility to examine lineshape derivatives; several such derivative …

Optimal Active And Passive Control Design For A Slewing Piezoelectric Laminate Beam, Travis V. Dubois

Mechanical & Aerospace Engineering Theses & Dissertations

This thesis presents the development and experimental verification of a distributed parameter model for a slewing beam system with piezoelectric actuators and sensors. Also presented is the development of an optimal active control synergism which employs IMSC, (Independent Modal Space Control) and an optimally designed, viscoelastic damping treatment. The beam is pinned at the proximal end and patches of thin piezoelectric laminates are attached to its surface. Formulation is general enough to allow the patches to be located anywhere on the beam's surface. A viscoelastic material with a constraining layer covers the rest of the beam. The differential equation of …

Using The Cern Program-Library Graphics And Interactive Data Display, Morgan T. Burks, Wilson H. Howe, Christine A. Byrd, Wilfred J. Braithwaite

Journal of the Arkansas Academy of Science

Small scale Monte Carlo programming is growing rapidly due to the ease with which complex problems may be formulated by any programmer. These programmers may choose to exploit graphics and interactive displays available in the program library developed and maintained by CERN (the Center for European Nuclear Research). This paper outlines the use of graphics and interactive data display features of the CERN program library, developed for visualizing simulated data events in particle detectors. One example uses GEANT, CERN's Monte Carlo modeling program, to simulate 300 MeV/c protons incident on a silicon slab. Display packages for GEANT are available both …

Low‐Cost Technique For Preparing N‐Sb2S3/P‐Si Heterojunction Solar Cells, O. Savadogo, K. C. Mandal

Faculty Publications

No abstract provided.

Absorption Imaging Studies On Intrinsic Gaas, John Samuel Kenney

Electrical & Computer Engineering Theses & Dissertations

A diagnostic technique has been developed which allows recording of the temporal and spatial development of electric field structures in GaAs photoconductive switches. The optical method is based on the Franz-Keldysh effect. Measurements were performed with a Nd:YAG activation laser and a GaAs laser diode as the probe laser. At low applied voltages a 100 atm wide region of high electric field is seen at the cathode only. With increasing voltage strong domain like structures emerge at the anode also. A calibration measurement shows that the electric fields in these domains are well above 50 kV/cm. At a threshold voltage, …

Light Injection From An Active Cladding To The Core Of A Fiber Optic Fluorosensor, Alvin Leon Bryant

Electrical & Computer Engineering Theses & Dissertations

A fluorosensor works on the basis of light injection from the clad into the core of an optical fiber. The sensitivity of such a sensor depends on the efficiency of light injection. Conditions necessary for a high injection efficiency are experimentally determined. The refractive index difference between the core and the clad,ⁿcore ^-nclad, must be maximized to achieve a high injection efficiency. Since an air clad has the least refractive index, a bare core fiber will have a maximum efficiency. Standard optical fibers used for communication employ a minimum value for ⁿcore ^-nclad, in order …

Electrostatic Positioning Of Droplets In Turbulent Flows (Lstm 375/Te/93), Nihad E. Daidzic, Adrian Melling

Aviation Department Publications

Report LSTM 375/TE/93, Lehrstuhl fuer Stroemungsmechanik Universitaet Erlangen-Nuernberg Cauerstr. 4, 8520 Erlangen Germany.

A Magnetic Suspension System With A Large Angular Range, Colin P. Britcher, Mehran Ghofrani

Mechanical & Aerospace Engineering Faculty Publications

In order to explore and develop technology required for the magnetic suspension of objects over large ranges of orientation, a small-scale laboratory system, the large-angle magnetic suspension test fixture (LAMSTF) has been constructed at NASA Langley Research Center. This apparatus falls into the category of large-gap, actively stabilized magnetic levitation systems. The hardware comprises five conventional electromagnets in a circular arrangement, each driven from a separate bipolar power amplifier. Electromagnet currents are commanded by a digital control system, implemented on a microcomputer, which in turn derives the position and attitude of the suspended element from an infrared optical system. The …

Hysteresis And Anchoring Energy In Ferroelectric Liquid Crystals, Yuri Panarin

Articles

The frequency dispersion of the coercive force of Ferroelectric Liquid Crystals (FLC) cells has been detected and examined in the range of infralow (lower than 0.1 Hz) frequencies. To clarify the low-frequency dispersion, the model has been suggested, based on the arrangement of free charges and well describing the experimental curves. The method for determination of the energy of FLC anchoring at the surface, developed on the basis of the static hysteresis loop, has been proposed. The dependence of bistability and the anchoring energy upon the orientant layer thickness has experimentally been investigated.

Processability Of Polythiophene Thin Films By Ultraviolet Photo Bleaching, Derek D. Fletcher

Theses and Dissertations

Materials possessing strong ��⁽³⁾ optical properties such as Polythiophene are sought for the production of optical switches. Polythiophene thin films produced by plasma enhanced CVD show a surface rms roughness of 10^-15 angstroms over single square micron areas which is acceptable for wave guiding in the near IR. This research investigates permanently changing the optical properties of such a thin film by exposure to UV radiation (254 nm, 35 mW/cm²), known as photo bleaching, in hope of creating a refractive index boundary for use in total internal reflection. After 60 minutes exposure the refractive index shows …

The Effect Of Contacts On The Performance Of Electron-Beam Controlled Gaas And Diamond Switches, Michael Kevin Kennedy

Electrical & Computer Engineering Theses & Dissertations

The performance of GaAs and diamond as electron-beam controlled closing and opening switches has been studied. An emphasis has been placed on the effect of contacts on the current-voltage characteristics. The two materials studied were GaAs and diamond. Using the same semi-insulating GaAs wafer as a source of material, a bulk device and a p-i-n device have been fabricated and compared. The asymmetry of the pin diode allows operation at higher voltage because of the ability to suppress the lock-on effect. Whereas GaAs was ionized through cathodoluminescence; diamond, in the form of thin films, has been directly ionized by the …

Detection, Location, And Quantification Of Structural Damage By Neural-Netprocessed Moire Profilometry, Barry G. Grossman, Frank S. Gonzalez, Joel H. Blatt, Jeffery A. Hooker

Electrical Engineering and Computer Science Faculty Publications

The development of efficient high speed techniques to recognize, locate, and quantify damage is vitally important for successful automated inspection systems such as ones used for the inspection of undersea pipelines. Two critical problems must be solved to achieve these goals: the reduction of nonuseful information present in the video image and automatic recognition and quantification of extent and location of damage. Artificial neural network processed moire profilometry appears to be a promising technique to accomplish this. Real time video moire techniques have been developed which clearly distinguish damaged and undamaged areas on structures, thus reducing the amount of extraneous …