Engineering Physics Commons^™

The Development Of A Laminated Copolyester Electric Guitar, Addison S. Karnes

Electronic Theses and Dissertations

This thesis is an investigation of the fabrication and assembly methodologies employed in the development of a proof-of-principle prototype electric guitar composed of laminated copolyester. The objective of the project was to develop the processes and procedures to create an optimized physical and visual bond between layers to minimize vibratory dissipation, thus maximizing sustain. A high speed CNC router, abrasive waterjet, laser engraver-cutter, as well as various manual fabrication and assembly methods were investigated in the construction of the guitar prototypes. The lamination processes explored include low-temperature, heat-assisted pressure bonding, solvent and chemical welding, and contact adhesives. The project concluded …

A Prototype Microwave Cavity Control Circuit For Use In Next Generation Free Electron Laser, Josh Thompson, Peter Neal Barrina, Jiayi Jiang, Joe Frisch, Steve Smith, Daniel Van Winkle

STAR Program Research Presentations

One of the current programs at SLAC National Accelerator Laboratory is the Linac Coherent Light Source, or LCLS. Using the existing hardware of the last third of their linear accelerator (or “linac”), SLAC has created one of the most energetic X-ray free electron lasers (or “FEL”). Since 2009, LCLS has used this FEL to perform a wide range of experiments across all sciences, most notably ultrafast filming at the molecular scale. As requests for beam-time with this laser increases, SLAC is purposing a linac upgrade to better match this demand. This upgrade, named LCLS-II, will replace existing copper radio frequency …

Does A Plastron Improve Heat Transfer?, Madani A. Khan, Jeffrey Alston, Andrew Guenthner

STAR Program Research Presentations

Superamphiphobic surfaces strongly repel both water and oils. In this work, aluminum coupons are processed by sanding with various grit of sand paper to impart microscale roughness. Subsequent submersion of the aluminum substrate in boiling water grows nanoscale grass-like structures. The oxide layer of Al is slightly soluble in water. During a fast diffusion/equilibrium, Al₂O₃ nanograss grows on the surface. A low energy coating is then deposited on the surface. The micro and nanoscale features create re-entrant structures that trap air enabling contact liquid to be in a Cassie-Baxter state. Superamphiphobicity of the samples were confirmed by …

The Use Of Object-Oriented Programming Concepts For Documenting A Model Ensemble, Georgii A. Alexandrov

International Congress on Environmental Modelling and Software

The spread of cloud computing services gives community modelling a reasonable opportunity to become a reality in scientific research. However, even if models will be deployed in clouds, and model codes will be open for re-use, there will be little progress in community modelling in the lack of consensus standards for model documentation. This paper is to discuss a conceptual framework for developing such standards. The proposed conceptual framework is based on the idea that a new model is often a modification of an old one, and hence, the similarities between the models of the same environmental process could be …

Effect Of Z1/2, Eh5, And Ci1 Deep Defects On The Performance Of N-Type 4h-Sic Epitaxial Layers Schottky Detectors: Alpha Spectroscopy And Deep Level Transient Spectroscopy Studies, M. A. Mannan, S. K. Chaudhuri, K. V. Nguyen, K. C. Mandal

Faculty Publications

No abstract provided.

Rubidium-Based Atomic Clock, Kate Miles

Physics

In this paper we will explore the process of building an atomic clock from a function generator, go into an in-depth introductory discussion of the Datum LPRO, and examine how rubidium function generators work.

Lightweight Uav Launcher, Ben Miller, Christian Valoria, Corinne Warnock, Jake Coutlee

Mechanical Engineering

This report discusses the design, construction, and testing of a lightweight, portable UAV launcher. There is a current need for a small team of soldiers to launch a US Marine Tier II UAV in a remote location without transport. Research was conducted into existing UAV launcher designs and the pros and cons of each were recorded. This research served as a basis for concept generation during the initial design development stage. It was required that the design weigh less than 110 lbs, occupy a smaller volume than 48" x 24" 18" in its collapsed state, be portable by a single …

Electrical Characterization Of Spherical Copper Oxide Memristive Array Sensors, James P. Orta

Theses and Dissertations

A new System Protection (SP) technology is explored by using electrical and mechanical interference-sensing devices that are implemented with granular memristive material. The granular materials consist of oxide-coated copper spheres with radii of about 700 µm that are placed in contact to produce thin oxide junctions which exhibit memristive behavior. Processes for etching, which compared acetic acid and nitric acid etches, and thermal oxidation at 100°C are performed and compared to produce copper spheres with a copper oxide layer over the sphere surface. Oxidized copper spheres are tested as sensor arrays by loading into a capillary tube in an aligned …

Large-Scale Solution Synthesis Of Narrow Graphene Nanoribbons, Timothy H. Vo, Mikhail Shekhirev, Donna A. Kunkel, Martha D. Morton, Eric Berglund, Lingmei Kong, Peter M. Wilson, Peter A. Dowben, Axel Enders, Alexander Sinitskii

Nebraska Center for Materials and Nanoscience: Faculty Publications

According to theoretical studies, narrow graphene nanoribbons with atomically precise armchair edges and widths of(1.1 eV), which makes them potentially promising for logic applications. Different top–down fabrication approaches typically yield ribbons with width >10nm and have limited control over their edge structure. Here we demonstrate a novel bottom–up approach that yields gram quantities of high-aspect-ratio graphene nanoribbons, which are only ~1 nm wide and have atomically smooth armchair edges. These ribbons are shown to have a large electronic bandgap of ~1.3 eV, which is significantly higher than any value reported so far in experimental studies of graphene nanoribbons prepared by …

Evolution Of Perturbations In Flow Field Mechanics, Samantha R. Bell, David Forliti, Nils Sedano, Kriss Vanderhyde

STAR Program Research Presentations

This project explores the stability analysis of a given flow field. Specifically, where the peak disturbance occurs in a flow as this is the disturbance that is most likely to occur. In rocket combustion, it is important to understand where the maximum disturbance occurs so that the mixing of fuel can be stabilized. The instabilities are the results of frequencies in the area surrounding the flow field. The linear stability governing equations are employed to better understand the disturbance. The governing equations for continuity and momentum in the x and y directions are used to form an equation for the …

Hfc(310) High Brightness Sources For Advanced Imaging Applications, William A. Mackie, Josh M. Lovell, Todd W. Curtis, Gerald G. Megara

Faculty Publications - Biomedical, Mechanical, and Civil Engineering

The authors report on electron emission from HfC(310) operating in extended Schottky emission mode. Data are gathered from test stands as well as through operation in a commercial scanning electron microscope. Emitter end-form geometry consisted of rounded, via electrochemical etching, and truncated, via ion milling. The authors demonstrate high angular intensity operation of >60 mA/sr especially for the rounded end-form emitters. Advantages include robustness of the material, which is not reliant on material supply as is the case with standard ZrO/W(100) sources. Hence, operation is available over a much larger range of temperatures, fields, and potentially pressures. Operation in a …

Robust And Adaptive Nonlinear Control Of Limit Cycle Oscillations In Uavs Using Synthetic Jet Actuators, Natalie Ramos Pedroza

Doctoral Dissertations and Master's Theses

Limit cycle oscillations (LCO), also known as utter, cause significant challenges in fight control of unmanned aerial vehicles (UAVs), and could potentially lead to structural damage and catastrophic failures. LCO can be described as vibrational motions in the pitching and plunging displacements of an aircraft wing. Even in low Reynolds number (low-Re) fight regimes, LCO can exceed the limiting boundary for safe UAV fight. Further, as practical considerations motivate the design of smaller, lighter weight UAVs, there is a growing need for UAV systems that do not require heavy mechanical actuators (e.g., ailerons). To address this, the use of synthetic …

Repeated Load Relaxation Testing Of Pure Polycrystalline Nickel At Room Temperature Using Nanoindentation, D. E. Stegall, M. A. Mamun, B. Crawford, A, A. Elmustafa

Mechanical & Aerospace Engineering Faculty Publications

We present the results of repeated relaxation tests using nanoindentation to derive the activation volume of the dislocation velocity and the ratios of the dislocation density and dislocation velocity. An experimental technique, based on classical uniaxial relaxation experiments, was developed to establish a constant strain during repeated load relaxation transients and then to calculate the stiffness of unloading, and therefore the hardness, across the transients with acceptable results. We found that the activation volume of the dislocation velocity from our nanoindentation methodology was in good agreement when compared to the same reported for uniaxial experiments. © 2014 AIP Publishing LLC.

Practical Aspects Of Modern And Future Permanent Magnets, R.W. Mccallum, L. H. Lewis, Ralph Skomski, M. J. Kramer, I. E. Anderson

Ralph Skomski Publications

The mandate to reduce greenhouse gases will require highly efficient electric machines for both power generation and traction motor applications. Although permanent magnet electric machines utilizing Nd2Fe14B-based magnets provide obvious power-to-weight advantages over induction machines, the limited availability and high price of the rare earth (RE) metals make these machines less favorable. Of particular concern is the cost and supply criticality of Dy, a key RE element that is required to improve the high-temperature performance of Nd-based magnetic alloys for use in generators and traction motors. Alternatives to RE-based alloys do exist, but they currently lack the energy density necessary …

Organic Ferroelectric Evaporator With Substrate Cooling And In Situ Transport Capabilities, Keith Foreman, C. Labedz, M. Shearer, Shireen Adenwalla

Shireen Adenwalla Papers

We report on the design, operation, and performance of a thermal evaporation chamber capable of evaporating organic thin films. Organic thin films are employed in a diverse range of devices and can provide insight into fundamental physical phenomena. However, growing organic thin films is often challenging and requires very specific deposition parameters. The chamber presented here is capable of cooling sample substrates to temperatures below 130 K and allows for the detachment of the sample from the cooling stage and in situ transport. This permits the use of multiple deposition techniques in separate, but connected, deposition chambers without breaking vacuum …

Electrospinning Applications Air Filtration And Superhydrophobic Materials, Negar Ghochaghi, Adetoun Taiwo

Graduate Research Posters

Electrospinning is a widely applicable technique that generates non-woven fibers in the micro and nano range. In this project two of its applications are highlighted namely filtration media and enhancement of wettability. The first project demonstrates that electrospinning can be used to produce new fiber filtration media with controlled microstructure. The bimodal and unimodal orthogonal and random filters were made and characterized against their filtration efficiency and pressure drop. Figure of Merit (FOM) was also calculated and discussed. It is shown that the FOM increases when the electrospun fibers are arranged into alternating layers of aligned course and fine fibers. …

Plasma Processes And Polymers Special Issue On: Plasma And Cancer, Mounir Laroussi, Michael Keidar

Electrical & Computer Engineering Faculty Publications

During the last two decades, research efforts on the application of low temperature plasmas in biology and medicine have positioned nonequilibrium lowtemperature plasmas as a technology that has the potential of revolutionizing healthcare.[1,2] Low temperature plasmas can be applied in direct contact with living tissues to inactivate bacteria,[3] to disinfect wounds and accelerate wound healing,[4] and to induce damage in some cancer cells.[5–11]

Near-Infrared Surface-Enhanced Fluorescence Using Silver Nanoparticles In Solution, Michael D. Furtaw

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Fluorescence spectroscopy is a widely used detection technology in many research and clinical assays. Further improvement to assay sensitivity may enable earlier diagnosis of disease, novel biomarker discovery, and ultimately, improved outcomes of clinical care along with reduction in costs. Near-infrared, surface-enhanced fluorescence (NIR-SEF) is a promising approach to improve assay sensitivity via simultaneous increase in signal with a reduction in background. This dissertation describes research conducted with the overall goal to determine the extent to which fluorescence in solution may be enhanced by altering specific variables involved in the formation of plasmonactive nanostructures of dye-labeled protein and silver nanoparticles …

Elementary Studies Of Twisted Bilayer Graphene, Branden P. Burns, Yong P. Chen

The Summer Undergraduate Research Fellowship (SURF) Symposium

In the nanotechnology field, some existing materials and applications are harmful to the environment, not efficient for certain tasks, or too expensive to be fully utilized. Graphene is a strong and cheap material that can be used to improve current nanotechnologies for more practical uses in society. Twisted bilayer graphene (TBG) is an orientation of graphene layers that exhibit different properties than regular bilayer graphene. It is made by placing a single layer of graphene on top of another at an angle with respect to the other lattice orientation. Understanding the characteristics of TBG is important to uncover more physics …

Synthesis And Optimization Of Vo₂ Thin Films For Phase Transition Applications By Atomic Layer Deposition And Rf Magnetron Sputtering, Madhavi Tangirala

Electrical & Computer Engineering Theses & Dissertations

Among many Vanadium oxides and suboxides, VO₂ has received considerable attention due to its remarkable metal-insulator transition (MIT) or semiconductor-metal transition (SMT) behavior, a reversible change in its electrical and optical properties that occurs due to a phase transition near a temperature of 68°C. Electrically, the resistivity of VO₂ can be changed as large as 4-5 orders of magnitude. Optically, the transmittance drops dramatically above the transition temperature in the metallic state where the VO₂ film becomes highly reflective in the infrared region. All these properties result in structural phase transformation from a low temperature monoclinic to …

Control System Of An Atomic Layer Deposition (Ald) Machine, Nitin Vishnu Hegde

Electrical & Computer Engineering Theses & Dissertations

Atomic Layer Deposition is one of the most efficient deposition processes for obtaining ultrathin films. The deposition by this process happens one atomic layer at a time. ALD is known for its precision and ability to develop quality films with great thickness control. ALD machines simultaneously control DC and AC currents, low pressure operations, temperature control and heating (up to 500'C), precision flow control, precision timing intervals for deposition (milli-second intervals) and constantly monitor temperature. Such a high control comes at a high price. Furthermore, at the university level, the capacity to modify or enhance a machine is critical but …

Feedback Stabilization At Spear3, Daniel Kelley, Jeff Corbett

STAR Program Research Presentations

The SPEAR3 synchrotron lightsource at SLAC relies on a sophisticated radio frequency (RF) timing system to maintain current – electrons – in the storage ring. One problem SPEAR3 operators have dealt with is the thermal expansion of one of the cables supporting this RF timing system. As the cable expands and contracts with the diurnal rise and fall of the sun, the phase of the RF in the cable shifts. This shifting phase affects the timing accuracy of electron injections into the storage ring.

A common feedback control algorithm PID (Proportional Integral Derivative) has countless applications in engineering. PID feedback …

Study Of A Non-Equilibrium Plasma Pinch With Application For Microwave Generation, Ahmad Al Agry

UNLV Theses, Dissertations, Professional Papers, and Capstones

The Non-Equilibrium Plasma Pinch (NEPP), also known as the Dense Plasma Focus (DPF) is well known as a source of energetic ions, relativistic electrons and neutrons as well as electromagnetic radiation extending from the infrared to X-ray. In this dissertation, the operation of a 15 kJ, Mather type, NEPP machine is studied in detail. A large number of experiments are carried out to tune the machine parameters for best performance using helium and hydrogen as filling gases. The NEPP machine is modified to be able to extract the copious number of electrons generated at the pinch. A hollow anode with …

Organic Solar Cells Based On High Dielectric Constant Materials: An Approach To Increase Efficiency, Khalil Jumah Tawfiq Hamam

Dissertations

The efficiency of organic solar cells still lags behind inorganic solar cells due to their low dielectric constant which results in a weakly screened columbic attraction between the photogenerated electron-hole system, therefore the probability of charge separating is low. Having an organic material with a high dielectric constant could be the solution to get separated charges or at least weakly bounded electron-hole pairs. Therefore, high dielectric constant materials have been investigated and studied by measuring modified metal-phthalocyanine (MePc) and polyaniline in pellets and thin films. The dielectric constant was investigated as a function of temperature and frequency in the range …

Modeling A Sensor To Improve Its Efficacy, Nabin K. Malakar, Daniil Gladkov, Kevin H. Knuth

Physics Faculty Scholarship

Robots rely on sensors to provide them with information about their surroundings. However, high-quality sensors can be extremely expensive and cost-prohibitive. Thus many robotic systems must make due with lower-quality sensors. Here we demonstrate via a case study how modeling a sensor can improve its efficacy when employed within a Bayesian inferential framework. As a test bed we employ a robotic arm that is designed to autonomously take its own measurements using an inexpensive LEGO light sensor to estimate the position and radius of a white circle on a black field. The light sensor integrates the light arriving from a …

Reversible Mn Segregation At The Polar Surface Of Lithium Tetraborate, Christina L. Dugan, Robert L. Hengehold, Stephen R. Mchale, Juan A. Colon Santana, John W. Mcclory, Volodymyr T. Adamiv, Yaroslav V. Burak, Ya B. Losovyj, Peter A. Dowben

Faculty Publications

We find Mn surface segregation for single crystals of Mn doped Li₂B₄O₇, nominally Li_1.95Mn_0.05B₄O₇(001), but as the temperature increases, evidence of this Mn surface segregation diminishes significantly. At room temperature, the surface photovoltaic charging is significant for this pyroelectric material but is quenched at a temperature well below that seen for the undoped Li₂B₄O₇ samples. The suppression of surface charging in the region of 120 °C that accompanies the temperature of Mn dissolution in the bulk of Li₂B_{4 …}

Universal Scaling And Intrinsic Classification Of Electro-Mechanical Actuators, Sambit Palit, Ankit Jain, Muhammad A. Alam

Birck and NCN Publications

Actuation characteristics of electromechanical (EM) actuators have traditionally been studied for a few specific regular electrode geometries and support (anchor) configurations. The ability to predict actuation characteristics of electrodes of arbitrary geometries and complex support configurations relevant for broad range of applications in switching, displays, and varactors, however, remains an open problem. In this article, we provide four universal scaling relationships for EM actuation characteristics that depend only on the mechanical support configuration and the corresponding electrode geometries, but are independent of the specific geometrical dimensions and material properties of these actuators. These scaling relationships offer an intrinsic classification for …

Examining The Validity Of Using A Gaussian Schell-Model Source To Model The Scattering Of A Fully Coherent Gaussian Beam From A Rough Impedance Surface, Santasri Basu, Milo W. Hyde Iv, Salvatore J. Cusumano, Michael A. Marciniak, Steven T. Fiorino

Faculty Publications

Military applications that use adaptive optics (AO) often require a point source beacon at the target to measure and correct for wavefront aberrations introduced by atmospheric turbulence. However, turbulence prevents the formation of such a point beacon. The extended beacons that are created instead have finite spatial extents and exhibit varying degrees of spatial coherence. Modeling these extended beacons using a Gaussian Schell-model (GSM) form for the autocorrelation function would be a convenient approach due to the analytical tractability of Gaussian functions. We examine the validity of using such a model by evaluating the field scattered from a rough impedance …

Study Of The Growth And Switching Kinetics On Ferroelectric Nanocrystals Of Copolymer Vinylidene Fluoride And Trifluoroethylene On An Atomic Force Microscope, R. V. Gaynutdinov, O. A. Lysova, A. L. Tolstikhina, V. M. Fridkin, S. G. Yudin, Stephen Ducharme

Stephen Ducharme Publications

The growth of nanocrystals obtained from Langmuir-Blodgett films of ferroelectric copolymer consisting of 70% vinylidene fluoride and 30% trifluoroethylene has been investigated by atomic force microscopy (AFM). The radius and concentration of nanocrystals are found to depend on the annealing time of the film. A model for nanocrystal growth is proposed which yields adequate time dependences for nanocrystal size parameters. The switching kinetics of individual ferroelectric nanocrystals with an average diameter of 100–200 nm and a height of 15–20 nm has been investigated in the piezoelectric response mode. It is shown that the switching of nanocrystals has an activation character.

Note: A Simple Thermal Gradient Annealing Unit For The Treatment Of Thin Films, C. J. Metting, Johnathan K. Bunn, Ellen A. Underwood, Yihao Zhu, G. Koley, T. Crawford, Jason R. Hattrick-Simpers

Faculty Publications

A gradient annealing cell has been developed for the high-throughput study of thermalannealing effects on thin-film libraries in different environments. The inexpensive gradientannealing unit permits temperature gradients as large as 28 °C/mm and can accommodate samples ranging in length from 13 mm to 51 mm. The system was validated by investigating the effects of annealing temperature on the crystallinity, resistivity, and transparency of tin-doped indium oxide deposited on a glass substrate by magnetron sputtering. The unit developed in this work will permit the rapid optimization of materials properties such as crystallinity, homogeneity, and conductivity across a variety of applications.