Engineering Physics Commons^™

Risk Assessment Of Dropped Cylindrical Objects In Offshore Operations, Adelina Steven

LSU New Orleans Theses and Dissertations

Dropped object are defined as any object that fall under its own weight from a previously static position or fell due to an applied force from equipment or a moving object. It is among the top ten causes of injuries and fatality in oil and gas industry. To solve this problem, several in-house tools and guidelines is developed over time to assess the risk of dropped objects on the sub-sea structures. This thesis focuses on compiling and comparing those methods in hope to improve the recommended practices available in the market. A simple modification is done on the in-house tools …

Effects Of Tension On Resonant Frequencies Of Strings, Blake Burnett

Senior Theses

This project tests and explores resonance of strings. Since all materials and mechanisms are affected by vibrations, it is important to know the frequencies at which resonance occurs. To explore this subject, strings were used as a model material to test the effect tension has on resonance. The fundamental frequencies and the corresponding modes of resonance were used to analyze the data. The results of this experiment show that increasing tension on a string increases its resonance frequency. Understanding the physics behind resonance frequency allows systems to be designed to take advantage of resonance properties, or to avoid resonance where …

Increasing The Longevity Of Tungsten Filaments In A Zone Refiner, Byron D. Greenlee

Senior Theses

Zone refining is used for its ability to purify material and grow single crystals. To produce these single crystals, a suspended molten zone, generated by electron bombardment, passes along the polycrystalline stock. During a zone refining run, the filaments that produce the electron bombardment can fail. In this project, the longevity of tungsten filaments in a zone refiner was investigated. A new bombardment geometry was constructed to attempt to increase the longevity of the filaments. The new geometry had a shield machined into it to prevent line-of-sight impurities originating in the molten zone from striking the filaments. It was found …

Measuring The Double Layer Capacitance Of Electrolyte Solutions Using A Graphene Field Effect Transistor, Agatha Ulibarri

Senior Theses

When operating graphene field effect transistors (GFETs) in fluid, a double layer capacitance (C_dl) is formed at the surface. In the literature, the C_dl is estimated using values obtained using metal electrode experiments. Due to the distinctive electronic and surface properties of graphene, there is reason to believe these estimates are inadequate. This work seeks to directly characterize the double layer capacitance of a GFET. A unique method for determining the C_dl has been implemented, and data has been obtained for three electrolytes and one ionic fluid. The results yield dramatically lower C_dl values than …

The Effects Of Surface Pace In Baseball, Jason Farlow

Senior Theses

A baseball travels across different surfaces at different paces. The goal of this experiment is to find a percentage difference in speeds the ball will reflect off a given surface. The energy lost on the turf surface was far more significant than on dirt surface as the turf lost an average of 26% of its energy as compared to just 16% of the energy on dirt. In the Northwest conference, teams play on four turf-based infields and five dirt-based infields. The results of this study suggest that kinetic friction forces are more significant in reducing ball rebound speed than in …

The Drag Coefficient Of Varying Dimple Patterns, James M. Seeley, Michael S. Crosser

Senior Theses

There are many golf balls on the market today with varying dimple sizes, shapes, and distribution. These proprietary differences are all designed to reduce drag on the balls during flight, allowing golfers to hit the ball farther distances. There are limited published studies comparing how varying the dimples affects the reduction of drag. An experiment was developed in which golf balls were pulled through a water tank to measure the drag force acting on each ball. The water was chosen to allow for testing at slower velocities than the typical necessary speeds to cause turbulence for balls traveling in air. …

Measuring The Double Layer Capacitance Of Electrolytes With Varied Concentrations, Geoffrey Rath

Senior Theses

When electric potentials are applied from an electrolytic fluid to a metal, a double layer capacitor, C_dl, develops at the interface. The layer directly at the interface is called the Stern layer and has a thickness equal to roughly the size of the ions in the fluid. The next layer, the diffuse layer, arises from the gathering of like charges in the Stern layer. This layer is the distance needed for ionic charges to return to equilibrium. This distance, called the Debye length, λ, depends on the square root of the electrolyte concentration. To study the properties of …

Mesoscale Computational Studies Of Thin-Film Bijels, Joseph M. Carmack

Graduate Theses and Dissertations

Bijels are a relatively new class of soft materials that have many potential applications in the technology areas of energy, medicine, and environmental sustainability. They are formed by the arrest of binary liquid spinodal decomposition by a dispersion of solid colloidal nanoparticles. This dissertation presents an in-depth simulation study of Bijels constrained to thin-film geometries and in the presence of electric fields. We validate the computational model by comparing simulation results with previous computational modeling and experimental research. In the absence of suspended particles, we demonstrate that the model accurately captures the rich kinetics associated with diffusion-based surface-directed spinodal decomposition. …

Numerical Simulation Of A High Strain Rate Biaxial Compression Apparatus, Michael Lagieski

McKelvey School of Engineering Graduate Student Theses & Dissertations

Few experimental methods today are capable of exploring the strength of materials at high strain rates (10⁵ s^-1). Those that are capable, such as the Split Hopkinson Bar, Taylor Anvil and Plate Impact suffer from instability and are generally limited to one dimensional wave propagation. Of particular interest is material response under biaxial compression, similar to that seen in inertial confinement fusion. Laser fusion fuel pellets typically undergo large strain rates as well as plastic deformation and non-linear behavior. This work briefly outlines an experimental procedure designed to replicate these large strain rates under biaxial compression using …

Characterization Of Magnetic Thin Films Using The Magneto Optic Kerr Effect, Nicholas J. Savino

Student Scholar Showcase

Understanding magnetic properties of materials allows for advances in applications such as data storage. The Magneto-Optic Kerr Effect (MOKE) displays the reflective response a magnetic material has to a magnetic field. When polarized light reflects off of a magnetic material, the polarization orientation can change. The application of an external magnetic field can affect how much this polarization changes in a non-linear manner. Hysteresis loops are created when examining the relationship between intensity of the reflected light to the applied magnetic field provide information about magnetic properties of that material, such as the coercive field and field retention. Preliminary measurements …

Comparison Of Plume Dynamics For Laser Ablated Metals: Al And Ti, William A. Bauer, Glen P. Perram, Timothy J. Haugan

Faculty Publications

Emissive plumes from pulsed laser ablation of bulk Ti and Al from KrF laser irradiation at laser fluence up to 3.5 J/cm² and argon background pressures of 0–1 Torr have been observed using gated intensified charged-coupled device imagery. Mass loss for Ti increases from 0.1 to 0.8 μg/pulse as pulse energy increase from 174 to 282 mJ/pulse (35–170 photons/atom) and decreases by ∼30% as pressure increases from vacuum to 1 Torr. Early plume energies are described by the free expansion velocities of 1.57 ± 0.02 and of 1.81 ± 0.07 cm/μs for Ti and Al, respectively, …

Nanostructural Origin Of Semiconductivity And Large Magnetoresistance In Epitaxial Nico2O4/Al2O3 Thin Films, Congmian Zhen, Xiaozhe Zhang, Wengang Wei, Wenzhe Guo, Ankit Pant, Xiaoshan Xu, Jian Shen, Li Ma, Denglu Hou

Xiaoshan Xu Papers

Despite low resistivity (~1 mΩ cm), metallic electrical transport has not been commonly observed in inverse spinel NiCo₂O₄, except in certain epitaxial thin films. Previous studies have stressed the effect of valence mixing and the degree of spinel inversion on the electrical conduction of NiCo₂O₄ films. In this work, we studied the effect of nanostructural disorder by comparing the NiCo₂O₄ epitaxial films grown on MgAl₂O₄ (1 1 1) and on Al₂O₃ (0 0 1) substrates. Although the optimal growth conditions are similar for the …

Bandgap Profiling In Cigs Solar Cells Via Valence Electron Energy-Loss Spectroscopy, Julia I. Deitz, Shankar Karki, Sylvain X. Marsillac, Tyler J. Grassman

Electrical & Computer Engineering Faculty Publications

A robust, reproducible method for the extraction of relative bandgap trends from scanning transmission electron microscopy (STEM) based electron energy-loss spectroscopy (EELS) is described. The effectiveness of the approach is demonstrated by profiling the bandgap through a CuIn_1-xGa_xSe₂ solar cell that possesses intentional Ga/(In + Ga) composition variation. The EELS-determined bandgap profile is compared to the nominal profile calculated from compositional data collected via STEM-based energy dispersive X-ray spectroscopy. The EELS based profile is found to closely track the calculated bandgap trends, with only a small, fixed offset difference. This method, which is particularly advantageous …

Copper-Doped Lithium Triborate (Lib3o5) Crystals: A Photoluminescence, Thermoluminescence, And Electron Paramagnetic Resonance Study, Brant E. Kananen, John W. Mcclory, Nancy C. Giles, Larry E. Halliburton

Faculty Publications

When doped with copper ions, lithium borate materials are candidates for use in radiation dosimeters. Copper-doped lithium tetraborate (Li2B4O7) crystals have been widely studied, but little is known thus far about copper ions in lithium triborate (LiB3O5) crystals. In the present investigation, Cu+ ions (3d10) were diffused into an undoped LiB3O5 crystal at high temperature. These ions occupy both Li+ and interstitial positions in the crystal. A photoluminescence (PL) band peaking near 387 nm and a photoluminescence excitation (PLE) band peaking near 273 nm verify that a portion of these Cu+ ions are located at regular Li+ sites. After an …

Investigation Of Toppling Ball Flight In American Football With A Mechanical Field-Goal Kicker, Chase M Pfeifer, Timothy J. Gay, Jeff A. Hawks, Shane Farritor, Judith M. Burnfield

Department of Mechanical and Materials Engineering: Faculty Publications

A mechanical field-goal kicking machine was used to investigate toppling ball flight in American football place-kicking, eliminating a number of uncontrollable impact variables present with a human kicker. Ball flight trajectories were recorded using a triangulation-based projectile tracking system to account for the football’s 3-dimensional position during flight as well as initial launch conditions. The football flights were described using kinematic equations relating to projectile motion including stagnant air drag and were compared to measured trajectories as well as projectile motion equations that exclude stagnant air drag. Measured football flight range deviations from the non-drag equations of projectile motion corresponded …

Saw Assisted Domain Wall Motion In Co/Pt Multilayers, Westin Edrington, Uday Singh, Maya Abo Dominguez, James Rehwaldt Alexander, Rabindra Nepal, Shireen Adenwalla

Shireen Adenwalla Papers

The motion of domain walls in thin ferromagnetic films is of both fundamental and technological interest. In particular, the ability to use drivers other than magnetic fields to control the positions of domain walls could be exciting for memory applications. Here, we show that high frequency dynamic strain produced by surface acoustic waves is an efficient driver of magnetic domain walls in ferromagnetic films with perpendicular anisotropy. A standing surface acoustic wave of resonant frequency 96.6MHz increases the domain wall velocities in thin films of [Co/Pt]n by an order of magnitude compared to magnetic fields alone. This effect is highly …

Generalizable Modeling Of Charge Transport In Single Electron Transistor Devices: Application To Thermal Sensitivity In Semiconducting Island Systems, Paniz Khanmohammadi Hazaveh

Dissertations, Master's Theses and Master's Reports

Electronic devices, especially MOSFETs, have been dimensionally scaled down to enhance operation of integrated circuits, addressing challenges such as current leakage, fluctuation of intrinsic semiconductor properties, and power dissipation. Reaching dimensions below 20 nm, there are fundamental limitations that are difficult to overcome, driving alternative device paradigms to be sought utilizing the quantum mechanical behavior of electrons. Single electron transistor (SET) devices are examples of a new generation of low-power transistors designed to transport information via single electron tunneling through one or more islands separated by tunnel junctions. Experimentally explored SET devices have shown that there are advantages to using …

Cryogenic Probe Station At Old Dominion University Center For Accelerator Science, Junki Makita, Jean R. Delayen, Alex Gurevich, Gianluigi Ciovati

Physics Faculty Publications

With a growing effort in research and development of an alternative material to bulk Nb for a superconducting radiofrequency (SRF) cavity, it is important to have a cost effective method to benchmark new materials of choice. At Old Dominion University's Center for Accelerator Science, a cryogenic probe station (CPS) will be used to measure the response of superconductor samples under RF fields. The setup consists of a closed-cycle refrigerator for cooling a sample wafer to a cryogenic temperature, a superconducting magnet providing a field parallel to the sample, and DC probes in addition to RF probes. The RF probes will …

Magnetron Sputtering Of Nb3Sn For Srf Cavities, Md. N. Sayeed, H. Elsayed-Ali, G. V. Eremeev, M. J. Kelley, U. Pudasaini, C. E. Reece

Electrical & Computer Engineering Faculty Publications

Nb₃Sn is a potential candidate for surface material of SRF cavities since it can enable the cavity to operate at higher temperatures with high quality factor and at an increased accelerating gradient. Nb-Sn films were deposited using magnetron sputtering of individual Nb and Sn targets onto Nb and sapphire substrates. The as-deposited films were annealed at 1200 °C for 3 hours. The films were characterized for their structure by X-ray Diffraction (XRD), morphology by Field Emission Scanning Electron Microscopy (FESEM), and composition by Energy Dispersive X-ray Spectroscopy (EDS) and Time of Flight Secondary Ion Mass Spectrometry (ToF-SIMS). The …

Real Time Spectroscopic Ellipsometry Analysis Of First Stage Cuin1-Xgaxse2 Growth: Indium-Gallium Selenide Co-Evaporation, Puja Pradhan, Puruswottam Aryal, Dinesh Attygalle, Abdel-Rahman Ibdah, Prakash Koirala, Jian Li, Khagendra P. Bhandari, Geethika K. Liyanage, Randy J. Ellingson, Michael J. Heben, Sylvain Marsillac, Robert W. Collins, Nikolas J. Podraza

Electrical & Computer Engineering Faculty Publications

Real time spectroscopic ellipsometry (RTSE) has been applied for in-situ monitoring of the first stage of copper indium-gallium diselenide (CIGS) thin film deposition by the three-stage co-evaporation process used for fabrication of high efficiency thin film photovoltaic (PV) devices. The first stage entails the growth of indium-gallium selenide (In_1-xGa_x)₂Se₃ (IGS) on a substrate of Mo-coated soda lime glass maintained at a temperature of 400 °C. This is a critical stage of CIGS deposition because a large fraction of the final film thickness is deposited, and as a result precise compositional control is desired in order to …

An Application Of M-Matrices To Preserve Bounded Positive Solutions To The Evolution Equations Of Biofilm Models, Richard S. Landry Jr.

LSU New Orleans Theses and Dissertations

In this work, we design a linear, two step implicit finite difference method to approximate the solutions of a biological system that describes the interaction between a microbial colony and a surrounding substrate. Three separate models are analyzed, all of which can be described as systems of partial differential equations (PDE)s with nonlinear diffusion and reaction, where the biological colony grows and decays based on the substrate bioavailability. The systems under investigation are all complex models describing the dynamics of biological films. In view of the difficulties to calculate analytical solutions of the models, we design here a numerical technique …

Artificial Olfactory System For Multi-Component Analysis Of Gas Mixtures., Alexander Aleksandrovich Larin

Electronic Theses and Dissertations

Gas analysis is an important part of our world and gas sensing technology is becoming more essential for various aspects of our life. A novel approach for gas mixture analysis by using portable gas chromatography in combination with an array of highly integrated and selective metal oxide (MOX) sensors has been studied. We developed a system with small size (7 x 13 x 16 inches), low power consumption (~10 W) and absence of special carrier gases designed for portable field analysis (assuming apriori calibration). Low ppb and even sub-ppb level of detection for some VOCs was achieved during the analysis …

Rogue Rotary - Modular Robotic Rotary Joint Design, Sean Wesley Murphy, Tyler David Riessen, Jacob Mark Triplett

Mechanical Engineering

This paper describes the design process from ideation to test validation for a singular robotic joint to be configured into a myriad of system level of robots.

University Of Minnesota Smallsat And High Altitude Ballooning Development And Collaboration, Luke Zumwalt, Ricardo Saborio, Athanasios Pantazides, Aaron Nightingale, Demoz Gebre Egziabher, Lindsay Glesener

2017 Academic High Altitude Conference

The Experiment for X-ray Characterization and Timing (EXACT) mission is a 3U CubeSat technology-development project being built by the SmallSat team at the University of MN – Twin Cities which is a joint research effort of the Aerospace Engineering and Mechanics (AEM) Department and the School of Physics and Astronomy (SPA). The main objective of this spacecraft is to carry a payload including a detector designed to measure energy and time of arrival time of individual hard x-ray photons emitted from the Sun and from other astrophysical sources. During the development process for EXACT, flights provided by the High-Altitude Student …

Measurement Of Speed Of Sound Profile Using Laaces Balloon, Zhuang Li, Brett Schaefer, Brian Schaefer, William Dever, Tyler Morgan, Matthew Foltz

2017 Academic High Altitude Conference

The goal of this mission is to test the speed of sound at different altitudes and ultimately at a maximum height of 100,000 feet (30 km). In conjunction with this testing, environmental parameters including temperature, pressure, and humidity are measured and used to calculate the speed of sound to compare to the measured results. The team constructed the payload “Dorothy” using polystyrene foam due to its lightweight and thermal isolation property. An ultrasonic sensor with a reflection mirror were installed outside payload box to measure speed of sound. All the sensors were calibrated. Software for the project was developed in …

Controlled Heading Automation Device, Robert Coulson

2017 Academic High Altitude Conference

One of the most significant limitations of weather balloon-based data collection is that instruments and payloads cannot depend on particular orientations or predictable rotation. Several investigators have used payload heading control devices to overcome this limitation in order to collect directional data and record motion controlled video footage. The work described in this presentation builds on the Controlled Heading Automation Device (CHAD) developed by Kruger et al. (2016) and was carried out at DePaul University in summer 2017 as an undergraduate research project. Our goal was to record stable video of the shadow of the moon on Earth’s surface during …

An Enhanced Operational Definition Of Dielectric Breakdown For Dc Voltage Step-Up Tests, Allen Andersen, Jr Dennison

Journal Articles

The imprecise definition of breakdown in the ASTM D3755-14 standard can misidentify breakdown. If the recommended test circuit current sensing element threshold is set too high, breakdown may occur undetected. Conversely, false positives may result from designating a low current threshold. An operational definition of breakdown much less sensitive to these pitfalls is outlined herein. This enhanced definition of breakdown is based on the average rate of change of the leakage current with increasing voltage, rather than a simple current threshold, avoiding ambiguous association with anomalies in current traces. For tests that continuously monitor leakage current, breakdown can be detected …

Spin-Imbalance In A 2d Fermi-Hubbard System, Peter Brown, Debayan Mitra, Elmer Guardado-Sanchez, Peter Schauß, Stanimir Kondov, Ehsan Khatami, Thereza Paiva, Nandini Trivedi, David Huse, Waseem Bakr

Faculty Publications

The interplay of strong interactions and magnetic fields gives rise to unusual forms of superconductivity and magnetism in quantum many-body systems. Here, we present an experimental study of the two-dimensional Fermi-Hubbard model—a paradigm for strongly correlated fermions on a lattice—in the presence of a Zeeman field and varying doping. Using site-resolved measurements, we revealed anisotropic antiferromagnetic correlations, a precursor to long-range canted order. We observed nonmonotonic behavior of the local polarization with doping for strong interactions, which we attribute to the evolution from an antiferromagnetic insulator to a metallic phase. Our results pave the way to experimentally mapping the low-temperature …

Solar Powered Single-Axis Heliostat Active Solar Tracking Device, Mason Kyle Roberts

Physics

As a means of cooking food, the burning of biomass accounts for over 4 million premature deaths in third world countries (“Household Air Pollution and Health”). The focus of this project was to explore an alternative that could utilize focused sunlight to cook food. A solar tracker was designed to be affixed to a parabolic, reflective, tilted single axis heliostat to follow the sun throughout the day and focus the reflected light to the bottom of a cooking surface. This surface became hot enough to for the preparation of food or boiling/sterilization of water.

A goal for each project was …

Interplay Of Quantum Size Effect, Anisotropy And Surface Stress Shapes The Instability Of Thin Metal Films, Mikhail Khenner

Mathematics Faculty Publications

Morphological instability of a planar surface ([111], [011], or [001]) of an ultra-thin metal film is studied in a parameter space formed by three major effects (the quantum size effect, the surface energy anisotropy and the surface stress) that influence a film dewetting. The analysis is based on the extended Mullins equation, where the effects are cast as functions of the film thickness. The formulation of the quantum size effect (Z. Zhang et al., PRL 80, 5381 (1998)) includes the oscillation of the surface energy with thickness caused by electrons confinement. By systematically comparing the effects, their contributions into the …