Polymer Chemistry Commons^™

Exploring Red Palm Oil As A Sustainable Plasticizer For Carbon Black-Filled Ssbr/Br Tire Tread Compounds: A Comparative Evaluation Of Commercial Alternatives, Norma Arisanti Kinasih, Mohamad Irfan Fathurrohman, Santi Puspitasari, Dewi Kusuma Arti, Abdulhakim Masa

Journal of Materials Exploration and Findings

This study investigates the application of red palm oil (RPO) as an alternative vegetable oil resource to substitute petroleum-based plasticizers, which have environmental and health concerns, in carbon black (CB)-filled SSBR/BR tire tread compounds. The plasticizing effects of RPO were thoroughly evaluated by comparing them with a commercial bio-based plasticizer, Epoxidized Soybean Oil (ESBO), and two safer petroleum-based oils, Naphthenic Oil (NYNAS) and Treated Distillate Aromatic Extract (TDAE). The initial investigation shows that fatty acid composition is imposing regarding the plasticizing effect. The higher unsaturated fatty acid content in RPO than in ESBO improved tensile strength and degraded rolling resistance …

Metallurgical Investigation Of A Modified Eye Bolt Failure Caused By Improper Weld Extension, Specification Deviation, And Crevice Corrosion, Dimas Muhammad Fawwaz, Reza Miftahul Ulum, Johny Wahyuadi Soedarsono, Yudha Pratesa

Journal of Materials Exploration and Findings

A modified eye bolt from the David Arm Manhole Storage Tank underwent thorough metallurgical study due to the consequences of the bolt's malfunction during operation. Safety issues arose when the manhole door detached during operation. The mechanical testing and chemical composition analysis of the bolts indicated they were manufactured from an ASTM A193 Grade B7 material used for high-temperature bolting. This material did not conform to the engineering drawing, which mentioned SA 563A, which is about nuts, not bolts. This contradiction clearly shows that the eye bolt which was installed does not conform to the intended design. Welded connections of …

Rejection Of Fe (Iron) And Kmno4 (Organic Substance) Parameters In Peat Water Using Organic Membranes, Muhamad Rafli Sakti Mulia Gonera, Siti Umi Kalsum, Sarah Fiebrina Heraningsih

Journal of Materials Exploration and Findings

Peat water is a surface water source widely used by people in swampy and lowland areas, but it has poor quality characteristics such as high organic matter content, low pH, and dissolved metal levels such as iron that exceed the threshold. These conditions can cause health problems and reduce the quality of clean water so that effective treatment technology is needed. This study aims to analyze the effectiveness of ultrafiltration membranes made from chitosan from shrimp shell waste in rejecting iron (Fe) and organic substances in peat water, and to determine the effect of pressure on separation performance. This study …

Techno-Enviro-Economic Analysis Of Precipitated Calcium Carbonate Production From Carbon Dioxide In Cement Industry Flue Gas And Calcium Hydroxide, Natalia Debora Panggabean, Widodo Wahyu Purwanto

Journal of Materials Exploration and Findings

CCUS is a technological solution to reduce emissions from the cement industry, which is the second largest CO2-intensive industry. This study aims to analyze technical, economic, and environmental performance of Precipitated Calcium Carbonate (PCC) synthesis in cement industry flue gas. The process simulation includes the CO2 capture system from cement plant, CO2 captured used as feedstock for PCC synthesis process through its reaction with calcium hydroxide. The simulation was carried out using ASPEN Plus software. Technical analysis was performed to determine the CO2 capture efficiency and PCC synthesis efficiency. Economic analysis was conducted to calculate CO2 capture cost and production …

Feasibility Analysis Of Thermal Oxidizer To Determine Remaining Life Using Fitness- For-Service Level 3 Method, Yudhi Yudistirawan, Donanta Dhaneswara, Wahyuaji Narottama Putra, Gama Widyaputra, Dewi Kurnia Suci, Agung Putra Mahardhika

Journal of Materials Exploration and Findings

An aged thermal oxidizer (TOX) in the oil and gas industry necessitates a comprehensive evaluation to ensure its continued safe operation. This study presents a Remaining Life Assessment (RLA) and a Fitness for Service (FFS) evaluation for the four main components of the TOX, in accordance with API 510, API 579/ASME FFS-1, and ASME BPVC Section VIII Div-1 standards. The investigation includes the determination of maximum stress and maximum temperature required to assess the operational viability of the reactor. The four components are radiant, convection, transition, and stack sections—were modeled using the finite element method (FEM). Following the geometric modeling, …

Analysis Of Leakage In Nearshore Pipelines Using Fitness For Service Method To Ensure Mechanical Integrity Based On Api-579 Level 3, Elriandri Elriandri, Dedi Priadi

Journal of Materials Exploration and Findings

The Fitness for Service (FFS) analysis is performed as a quantitative assessment to evaluate the integrity condition of a pipeline. Essentially, FFS assessment helps determine whether equipment components can operate safely despite existing deficiencies. This evaluation is carried out using the Finite Element Method (FEM). In the case of an underwater pipeline that experiences leak due to anchor pull at the flange connection, it undergoes plastic deformation and is lifted approximately 1 meter. As a mitigation step, inspection and repairs have been carried out by the company. Subsequently, modeling is performed to reconstruct the deformation process of the pipeline. Then, …

Assessment Of The Melt Quality Of A 30% Scrap Adc12 Aluminium Alloy Using The Inclusion And Fluidity Measurement Instrument (Ifmi) With Mullite Ceramic Filters, Gusti Ruri Ruri Lestari, Sandya Ananda Riswan, Muhammad Anis, Ahmad Ashari, Paramita Vidya Ayuningtyas, Bambang Suharno Prof, Donanta Dhaneswara

Journal of Materials Exploration and Findings

The increasing demand for sustainable practices in the metal casting industry has driven the use of recycled aluminum alloys such as ADC12. However, the addition of aluminum scrap tends to increase oxide inclusions, which reduce melt fluidity and compromise casting quality. This study utilizes the Inclusion and Fluidity Measurement Instrument (IFMI), equipped with mullite ceramic filters, to assess the melt quality of ADC12 aluminum alloy containing 30% scrap. Fluidity and inclusion characteristics were evaluated at five pouring temperatures (660°C, 680°C, 700°C, 720°C, and 740°C). The results show that fluidity increased with temperature, reaching a peak of 84.6 g·s⁻¹ at 740°C, …

Equipment Criticality Analysis To Determine Asset Integrity Management System Scheme In Supporting Production Optimization Scenarios In The Aeging Field, Donny Andryanto, Donanta Dhaneswara

Journal of Materials Exploration and Findings

This research investigates the production decline and cost increase in the X&Y oil and gas fields from 2022 to 2023. Production fell by 34%, while production costs per barrel rose by 79%. To address these issues, a series of optimization processes are proposed. These aim to restructure and enhance the production facilities to reduce current production costs. The optimizations include reducing pressure at the PPP Platform in 2024. Additional steps include shutting down CPP-ORF 14” pipelines and most processes at CPP 2 Platform by 2027 to convert it into an accommodation platform. Further, the plan involves optimizing the release of …

An Overview Of Biomass-Derived Graphene Oxide And Its Characteristics For Future Sustainable Applications, Afif Wardana, Ahmad Nabil Shahab, Donanta Dhaneswara, Nofrijon Sofyan

Journal of Materials Exploration and Findings

The production of graphene oxide (GO) from biomass presents considerable promise as a sustainable alternative substitute for traditional semiconductors. Biomass waste, abundant and often underutilized worldwide, is distinguished by its high carbon content and regenerative characteristics, rendering it an optimal resource for sustainable material production. By heating its biopolymers, lignocellulosic biomass can be used as a new material to make graphene, which forms three-dimensional turbostratic crystallites. These crystallites, composed of partially defective aromatic carbon sheets with graphite-like characteristics, make it easier to create GO with specialized functions for cutting-edge applications. Its capability underscores the revolutionary potential of biomass waste in …

Morphological Test Of Areca Nut Fiber Ceramic Membrane Using Scanning Electron Microscopy Energy Dispersive X-Ray Mapping Spectroscopy, Amelia Marzain, Siti Umi Kalsum, Marhadi Marhadi, Ahmad Nabil Shahab

Journal of Materials Exploration and Findings

This study investigates the potential of ceramic membranes derived from areca nut fiber as a cost-effective and environmentally sustainable material for the removal of iron (Fe) and manganese (Mn) from groundwater. Two types of membranes were fabricated: one without activation and one chemically activated using 10% sodium hydroxide (NaOH). The morphological and elemental characteristics of both membranes were analyzed using Scanning Electron Microscopy (SEM) and Energy Dispersive X-ray (EDX) mapping. The concentrations of Fe and Mn before and after treatment were measured using Atomic Absorption Spectroscopy (AAS). The NaOH-activated membrane exhibited a more porous surface structure and higher oxygen content, …

A Study Of Wear Measurement And Life Prediction Of Insert Chute Liner On Gold Ore Processing, Ferry Ardika Natanael, Nony Maulidya, Dedi Priadi

Journal of Materials Exploration and Findings

Chutes are critical materials handling assets to transport solid particles from one process step to another in mineral processing, coal mining and cement industries. The material transport, because of material characteristics, cause severe wear on internal lining of chutes or bins’ structure. The wear problem on internal lining of bins or chutes needs to be checked to keep production efficiency. Therefore, not checked wear rate causes liner replacement schedule becomes unpredictable. It leads to production loss and highly cost maintenance in industry. This study shows that condition-based maintenance through regular thickness measurement using Ultrasonic Transducer (UT) to predict life service …

Techno-Enviro-Economic Approach For Electrification Of Rural And Shrimp Farming Regional Development Of An Isolated Island In Indonesia By Utilizing Hybrid Renewable Energy Systems, Fiqih Akbar Wijaya, Mohammad Akita Indianto

Journal of Materials Exploration and Findings

One of the challenges in developing and archipelagic countries such as Indonesia is maintaining energy demand in rural and isolated areas due to difficulties in electrical distribution. For instance, in areas like Bawean Island, no additional electricity capacity has been introduced in the past year, leading to an unmet potential customer demand. One of the possible options is by utilizing Hybrid Renewable Energy Systems (HRES) that are integrated with existing fossil fuel-based energy systems to support the growing energy demand in the remote island. A case study in Bawean Island is conducted with the projected energy demand covers the energy …

Remaining Life Assessment And Fitness For Service Evaluation Of Aging Chemical Reactors In Polyethylene Terephthalate Resin Industry, Aditya Pahlawan Munthe, Donanta Dhaneswara, Wahyuaji Narottama Putra, Gama Widyaputra

Journal of Materials Exploration and Findings

Aging chemical reactors in the polyethylene terephthalate (PET) resin industry require comprehensive evaluation to ensure safe continued operation. This study conducts a remaining life assessment (RLA) and fitness-for-service (FFS) evaluation on five 30-year-old reactors, based on API 510, API 579/ASME FFS-1, and ASME BPVC Section VIII Div. 1 standards. The analysis involves corrosion rate measurement, future corrosion allowance (FCA) projection, and minimum thickness verification. Among the reactors, R-120 was found to have the shortest remaining life less than 15 years. FFS assessments using three criteria Average Measured Thickness, MAWP from Point Thickness Readings, and Minimum Measured Thickness confirm that R-120 …

Analysis Of Leak Testing Planning For Carbon Dioxide Piping Systems In The Development Of Carbon Capture, Utilization, And Storage Facilities In The Bintuni Basin, Devi Sentiani, Akhmad Herman Yuwono Professor

Journal of Materials Exploration and Findings

Carbon Capture, Utilization, and Storage (CCUS) technologies have become a key strategic response to global efforts to reduce CO₂ emissions. This study presents a leak testing strategy designed for a carbon dioxide (CO₂) piping system as part of a Carbon Capture, Utilization, and Storage (CCUS) project in the Bintuni Basin, West Papua, Indonesia. This study aims to ensure the system is properly prepared before commissioning by designing a leak test plan that is both practical and technical, based on ASME B31.3, ASME PCC-2, and API STD 520 Part 1. We conducted the process, which involves identifying the system boundaries, …

Assessment Of H2s-Induced Cracking Susceptibility In Steam Line Pipes And Weld Zones During Geothermal Well Construction, Riene Kaelamanda Pragitta, Yudha Pratesa

Journal of Materials Exploration and Findings

The susceptibility of steam line pipes, especially in the HAZ (heat-affected zone) and weldment areas, to hydrogen sulfide in the geothermal industry is crucial to understand from the early stages, particularly during construction. The combination of tensile stress from residual stresses after welding and metallurgical phase transformation makes the joint areas vulnerable to sulfide stress cracking. This condition becomes even more extreme when the equipment operates during the well stimulation phase. This research assesses the severity of H₂S-induced cracking using NACE MR0175 and ISO 15156-1 standards, focusing on the effects of pH and partial pressure of H₂S (p_{H₂S …}

Biobased Acrylate Composites With Enhanced Strength For Additive Manufacturing, Nicole Wagner, Joseph Mcwherter

Engineering Faculty Articles and Research

With the expanding use of polymers in additive manufacturing, sustainable resins for use in vat photopolymerization are required to reduce their environmental impact. One promising approach to achieve this is to incorporate biobased fillers that replace the acrylates in photopolymer resins as ‘green’ alternatives. In this study, photopolymer composites consisting of a methacrylate resin with varying calcium carbonate powder content between 0 and 50 wt.% were investigated. A digital light processing technique was used to fabricate tensile test specimens for mechanical testing. Good printability, dimensional accuracy, and good interlayer adhesion were observed for composite resin formulations that incorporated calcium carbonate …

Effect Of Alkyd And Polyester Resin Compositions On Corrosion Resistance, Blistering, And Adhesion In Utilization Of Oily Sludge As Anti-Rust Coating Material, Gerets Land Kakalang, Yohanes David Kristianto, Johny Wahyuadi Mudaryoto

Journal of Materials Exploration and Findings

Oil sludge is a waste derived from upstream and downstream activities of the oil and gas industry which is estimated at 10,000 tonnes generated from all PERTAMINA downstream activities spread across various fields, processing units and depots throughout Indonesia. Oil sludge has the same characteristics as asphalt, where asphalt in previous studies can be used as an anti-rust coating, so that the handling of oily sludge can be topped up by reusing and having its own added value. The purpose of this research is to utilise waste oily sludge as an alternative anti-rust coating material and compare alkyd resin and …

Analysis Of The Effect Of Different Surface Preparation Methods On Corrosion Resistance And Adhesion Strength Of Astm A36 Steel Substrate With Surface Tolerant Epoxy Paint As Coating Material, Irwan Wijaya Santoso, Daffa Aqila, Rini Riastuti, Rizal Tresna Ramadhani

Journal of Materials Exploration and Findings

In the industrial world, to extend the service life of materials, protection methods are carried out to slow down the material's corrosion rate. The protection method that is often used is the coating method. The coating method is a protection method by coating the substrate material using a coating material to prevent contact between the substrate material and the environment. In this research, the substrate material used is ASTM A36 steel and the coating material used is Surface Tolerant Epoxy paint. The independent variable used in this study lies in the surface preparation method which consists of: solvent cleaning, hand …

Combined Risk Based Inspection And Fault Tree Analysis For Repetitive 3-Phase Line Piping Leakage At West Java Offshore Topside Facility, Dona Yuliati, Akhmad Herman Yuwono, D. Rizal Asral, Donanta Dhaneswara

Journal of Materials Exploration and Findings

Hydrocarbon releases might result in serious consequences in various aspects. In addition to the contribution to environmental pollution, repetitive leakages need high repair costs. This study aim is to minimize potential repetitive leakage for other typical 3-phase piping systems. We conducted the risk assessment by adopting Risk Based Inspection (RBI) API 581 to identify risk level, calculating piping lifetime, recommended inspection plan and mitigations. The most relevant root causes can be obtained through quantitative Fault Tree Analysis (FTA). Observation and investigation was taken from eight 3-phase piping systems that experienced repetitive leakages. It has been found that the risk level …

Nitrogen Gas Quenching Pressure Effect On Bs S155 Alloy Steel In Vacuum Furnace, Agus Mulyadi Hasanudin, Eddy Sumarno Siradj

Journal of Materials Exploration and Findings

The production of metal and alloy products requires the use of heat treatment, when during the heat treatment process, quenching is a crucial step. The quenching medium can be anything from water, a salt bath, oil, air and gas. In a vacuum furnace, pressurized gas, most frequently nitrogen (N₂) gas, serves as one of the quenching mediums. One of the drawbacks of the quenching process is the distortion and dimensional change of the parts. This paper aims to investigate the influence of nitrogen gas quenching pressure on the distortion and dimensional change of aerospace actuator gear planet parts …

Gold(I)-Hydroarylation In Polymer Modification – Alkynes And Alkenes With Unexpected Reactivity, Samuel B. Hunt

Dissertations

Polymer modification is crucial for developing new properties and materials from recalcitrant waste polymers. Synthetically, polymers possess a chemical inertness that renders their functionalization challenging. Specifically, the omnipresence of C–H bonds in all commercial polymers endows their chemical resistance. Thus, developments in C–H activation chemistry are crucial to polymer diversification processes and allow for fundamental insight into the role of material processing conditions on novel chemical reactions. Au(I)-chemistry has recently come to the fore owing to a unique chemical reactivity nonexistent with other transition metals. The alkynophilicity of Au(I), in tandem with their insensitivity to common polymer processing conditions (air, …

Bbt Acoustic Alternative Top Bracing Cadd Data Set-Norev-2022jun28, Bill Hemphill

STEM Guitar Project’s BBT Acoustic Kit

This electronic document file set consists of an overview presentation (PDF-formatted) file and companion video (MP4) and CADD files (DWG & DXF) for laser cutting the ETSU-developed alternate top bracing designs and marking templates for the STEM Guitar Project’s BBT (OM-sized) standard acoustic guitar kit. The three (3) alternative BBT top bracing designs in this release are
(a) a one-piece base for the standard kit's (Martin-style) bracing,
(b) 277 Ladder-style bracing, and
(c) an X-braced fan-style bracing similar to traditional European or so-called 'classical' acoustic guitars.

The CADD data set for each of the three (3) top bracing designs includes …

Bbt Side Mold Assy, Bill Hemphill

STEM Guitar Project’s BBT Acoustic Kit

This electronic document file set covers the design and fabrication information of the ETSU Guitar Building Project’s BBT (OM-sized) Side Mold Assy for use with the STEM Guitar Project’s standard acoustic guitar kit. The extended 'as built' data set contains an overview file and companion video, the 'parent' CADD drawing, CADD data for laser etching and cutting a drill &/or layout template, CADD drawings in AutoCAD .DWG and .DXF R12 formats of the centerline tool paths for creating the mold assembly pieces on an AXYZ CNC router, and support documentation for CAM applications including router bit specifications, feeds, speed, multi-pass …

Design Of Pigments For Use In “Cool” Coatings, Tyler Laughorn

Williams Honors College, Honors Research Projects

This project was focused on the development and testing of several novel pigments that exhibit high NIR-reflectance and therefore show potential for use in “cool” coatings. A “cool” coating will reflect more solar radiation than other standard coatings, and so a coated structure would require less energy to keep cool. Four sets of pigments were synthesized: Co_1-xMg_xCr₂O₄ (teal), Co_0.25Mg_0.75Cr_2-yAl_yO₄ (blue), Ti_1-x-yNi_xSb_yO₂ (yellow), and Cr_2-xFe_xO₃ (black). NIR and TSR values were then measured …

Measuring Accuracy Of Two 3d Printing Materials, Mudassir Ali

Master of Technology Management Plan II Graduate Projects

Part accuracy is one of the important aspect in the manufacturing industry. The overall inaccuracy of the parts being built by RP technology has been one of the major challenges that need to be overcome. Though all the printing materials come with specifications, but the suppliers and manufactures does not specify the accuracy of the materials. In this study we established a study which compares the accuracy of the materials in consideration and performed an experiment to establish the superiority of a material in terms of accuracy over each other. The purpose of this project was to compare the dimensional …