Polymer Chemistry Commons^™

Characterization And Optimization Of Sand And Tung Oil-Based Resins For Binder-Jet 3d Printing, Daniel I. Ajiola

College of Graduate Studies: Theses & Dissertations

Binder-jet 3D printing as a transformative technology in additive manufacturing, offers the ability to fabricate complex structures with diverse materials. This thesis investigates the use of a sustainable tung oil-based resin to create composites, exploring the potential for an eco-friendly alternative to synthetic binders.

The aim of this research is to develop and characterize a bio-based resin formulation, using tung oil as the primary binder, for application in binder-jet 3D printing with sand as the reinforcement. The resin formulation was prepared by combining tung oil, n-butyl methacrylate, divinylbenzene, and di-tert-butyl peroxide in precise proportions, ensuring a balanced mixture that supports …

Single-Step Synthesis Of Activated Carbon From Arabica Spent Coffee Ground Using K2co3 As Activator Agent, Ghina Ivana Mieldan, Yuliusman Yuliusman

Journal of Materials Exploration and Findings

Activated carbon is a nanomaterial that is often used as an effective adsorbent. Activated carbon raw materials can use biomass, such as coffee grounds, which can be found along with the growth of public interest in coffee drinks. Chemical activators are used for activation to increase biomass carbon's adsorption capacity. Using K₂CO₃ activator to increase the specific surface area of activated carbon is more harmless than KOH. The use of spent coffee grounds as carbon source and food additive K₂CO₃ as an activator can make food-grade activated carbon that can be used for food. …

Effect Of Alkyd And Polyester Resin Compositions On Corrosion Resistance, Blistering, And Adhesion In Utilization Of Oily Sludge As Anti-Rust Coating Material, Gerets Land Kakalang, Yohanes David Kristianto, Johny Wahyuadi Mudaryoto

Journal of Materials Exploration and Findings

Oil sludge is a waste derived from upstream and downstream activities of the oil and gas industry which is estimated at 10,000 tonnes generated from all PERTAMINA downstream activities spread across various fields, processing units and depots throughout Indonesia. Oil sludge has the same characteristics as asphalt, where asphalt in previous studies can be used as an anti-rust coating, so that the handling of oily sludge can be topped up by reusing and having its own added value. The purpose of this research is to utilise waste oily sludge as an alternative anti-rust coating material and compare alkyd resin and …

Influence Of Glycopolymer Structure On Amphiphilic, Hybrid, Linear Branched Block Copolymer Properties For Use In Biomedical Applications, Kevin Green

Dissertations

The focus of this dissertation is evaluating and adding fundamental knowledge regarding the structure-property relations of glycopolymers used in the design of hybrid block copolymers (HBC) that are cable of self-assembling into delivery vehicles for biomedical applications. A shift to the utilization of natural materials in the design and fabrication of drug-delivery vehicles has garnered significant attention. Understanding the effects of linear glycopolymers content and composition on the resulting HBCs properties can provide valuable insight into how these materials may be tailored for use in targeted biological applications.

The first chapter introduces current literature on the need for improvement in …

Solubility Characterization Of Organic Molecules For Aqueous Organic Redox Flow Batteries, Anthony W. Ferrell, Harkeerith K. Vij, Seamus D. Jones

College of Engineering Summer Undergraduate Research Program

The major obstacle to renewable energy sources is a lack of long-term energy storage capabilities. Energy produced during the day dissipates, leaving insufficient electricity for at night. The goal of the project is to design an Aqueous Organic Redox Flow Battery (AORFB) to act as long-term energy storage. Work has been done using machine learning to identify suitable compounds for the batteries. In this work there was no indication as to the aqueous solubility of the molecules; this controls the device’s energy storage capabilities. We used a machine learning model to determine the aqueous solubility of slightly more than 3000 …

Chemical Recycling Of Bio-Based Polyurethane Foams: Evaluating Bio-Based Glycols In Comparison To Petroleum-Based Glycols, Anirudh Thorbole Mr.

Electronic Theses & Dissertations

The paradigm shift towards bio-based polyurethane foams (bio-PUF) has significantly increased post-consumer waste. To address this issue, this research represents a novel approach to enhance sustainable development in the recycling industry by replacing traditional petroleum-based glycols with sustainable bio-based alternatives. This study explores the glycolysis of bio-PUF using bio-based SG-522 glycol and polyethylene glycol (PEG) for comparison. The findings from this research as outlined, reveal no significant differences in depolymerization time between the two glycols, achieving proper depolymerization and high recovery yields of over 95% after solvent purification. Comprehensive FT-IR and NMR analyses confirmed the successful degradation of bio-PUF and …

Poly(Thioether) Thermosets With Gated Photodegradation, Surabhi Jha

Dissertations

Photodegradable polymer networks are attractive due to the precise spatiotemporal control and large-area applicability of light. Chemical linkages that enable these polymer networks to be photo-responsive, also hinder their applicability in ambient light. Photostable and photodegradable networks have recently been reported to overcome this challenge by combining other stimuli with light for degradation. We report the design of a network that responds to a simultaneous, dual stimulus for photodegradation. We design poly(thioether acetal) networks with benzylidene acetal moieties that are known to undergo β-scission in the presence of free thiols. By blocking these free thiols with a thermally labile protecting …

Analysis Of The Effect Of Different Surface Preparation Methods On Corrosion Resistance And Adhesion Strength Of Astm A36 Steel Substrate With Surface Tolerant Epoxy Paint As Coating Material, Irwan Wijaya Santoso, Daffa Aqila, Rini Riastuti, Rizal Tresna Ramadhani

Journal of Materials Exploration and Findings

In the industrial world, to extend the service life of materials, protection methods are carried out to slow down the material's corrosion rate. The protection method that is often used is the coating method. The coating method is a protection method by coating the substrate material using a coating material to prevent contact between the substrate material and the environment. In this research, the substrate material used is ASTM A36 steel and the coating material used is Surface Tolerant Epoxy paint. The independent variable used in this study lies in the surface preparation method which consists of: solvent cleaning, hand …

Thermal Frontal Polymerization – Applications In Coatings And Composites, Maria Martinez

LSU Doctoral Dissertations

Thermal frontal polymerization has long been used as a method to cure composites and coatings. However, this is the first time these applications have been used without the use of a catalyst, for the case of composites and coatings.

Chapter 2 discusses how to optimize cure-on-demand, thin layer coatings, using frontal polymerization. Previously, for the use of curing thin layer coating using thermal FP, it was known to just make the formulation viscous enough, as this would prevent premature quenching caused by heat loss. It was discovered that for a given layer thickness, a minimum viscosity and initiator concentration were …

Combined Risk Based Inspection And Fault Tree Analysis For Repetitive 3-Phase Line Piping Leakage At West Java Offshore Topside Facility, Dona Yuliati, Akhmad Herman Yuwono, D. Rizal Asral, Donanta Dhaneswara

Journal of Materials Exploration and Findings

Hydrocarbon releases might result in serious consequences in various aspects. In addition to the contribution to environmental pollution, repetitive leakages need high repair costs. This study aim is to minimize potential repetitive leakage for other typical 3-phase piping systems. We conducted the risk assessment by adopting Risk Based Inspection (RBI) API 581 to identify risk level, calculating piping lifetime, recommended inspection plan and mitigations. The most relevant root causes can be obtained through quantitative Fault Tree Analysis (FTA). Observation and investigation was taken from eight 3-phase piping systems that experienced repetitive leakages. It has been found that the risk level …

Nitrogen Gas Quenching Pressure Effect On Bs S155 Alloy Steel In Vacuum Furnace, Agus Mulyadi Hasanudin, Eddy Sumarno Siradj

Journal of Materials Exploration and Findings

The production of metal and alloy products requires the use of heat treatment, when during the heat treatment process, quenching is a crucial step. The quenching medium can be anything from water, a salt bath, oil, air and gas. In a vacuum furnace, pressurized gas, most frequently nitrogen (N₂) gas, serves as one of the quenching mediums. One of the drawbacks of the quenching process is the distortion and dimensional change of the parts. This paper aims to investigate the influence of nitrogen gas quenching pressure on the distortion and dimensional change of aerospace actuator gear planet parts …

Characterization Of Interlayer Laser Shock Peening During Fused Filament Fabrication Of Polylactic Acid (Pla), Fabien Denise

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

The field of additive manufacturing (AM) has gained a significant amount of popularity due to the increasing need for more sustainable manufacturing techniques and the adaptive development of complex product geometries. The problem is that AM parts routinely exhibit flaws or weaknesses that affect functionality or performance. Over the years, surface treatments have been developed to compensate certain flaws or weaknesses in manufactured products. Combining surface treatments with the modularity of additive manufacturing could lead to more adaptable and creative improvements of product functions in the future. The current work evaluates the feasibility of pursuing a new research axis in …

Characterization Of Mechanically Recycled Polylactic Acid (Pla) Filament For 3d-Printing By Evaluating Mechanical, Thermal, And Chemical Properties And Process Performance, Mahsa Shabani Samghabady

All Theses

Polylactic acid (PLA) is a biopolymer made from renewable resources such as sugar and corn. PLA filament is a popular material used in Fused Deposition Modeling (FDM) 3D-printing. While this material has many advantages, all the failed parts, support structures, rafts, nozzle tests, and the many prototype iterations during the 3D-printing process contribute to the plastic pollution and release of greenhouse gases. Although PLA is biodegradable, it can take years to degrade in landfills. Instead of throwing away PLA waste and buying new filaments, PLA can be recycled. Amongst the different recycling technologies, mechanical recycling is the most environmentally friendly. …

The Effect Of Heat Treatment And Chemical Treatment On Natural Fibre To The Durability Of Wood Plastic Composites – A Review, Nuratiqah Asyiqin Mohd Nasharudin, Nur Fatihah Sulaiman, Nurul Aziemah Mohammad, Wan Nor Raihan Wan Jaafar, Falah Abu Dr., Siti Norasmah Surip

Journal of Materials Exploration and Findings

The application of WPC is not only limited to indoor applications but has been extended to exterior applications where properties of WPC could compromise during service life. WPC was derived from wood fiber of various sizes to reinforce polymers. Wood fiber has the advantage of a cheaper price, being abundantly available, and ease of processing, however, the critical factor is its hydrophilic nature, where moisture absorption is likely to occur. Thus, treatments for reducing the hydrophilicity of wood fibers are applied. By treatment of wood fiber, the surface impurities were removed, leaving the roughened surface of fibers, thus providing a …

Covalent Adaptable Networks For Wood Coatings, Jachin Boaz Clarke

Materials Engineering

Wood swells and shrinks causing problems with seasonal humidity. Applying thick coatings of reactive finishes based on cross-linked polyurethane, epoxy, or polyesters can slow moisture-vapor exchange. However, the use of thick coatings leads to cracking and crazing sooner than thin finishes. This research proposes the addition of 3.3 mol % triazabicyclodecene, a conventionally used covalent adaptable network catalyst, in a commercially available polyester-based wood coating. The self-healing of the wood coating is tested using DMA stress relaxation and compression molding. The result from DMA renders inconclusive and compression molding indicates the novel wood coating oxidizes at elevated temperatures. The wood …

Enhancing Compatibility And Mechanical Properties Of Natural Rubber Composites, Krisma Yessi Sianturi, Adam Febriyanto Nugraha, Belle Kristaura, Mochamad Chalid

Journal of Materials Exploration and Findings

Pure natural rubber (NR) exhibits low mechanical properties, necessitating the incorporation of additives like vulcanizing agents and fillers. Carbon black and silica, conventional fillers, are relatively expensive and not environmentally friendly. This study explores using Oil Palm Empty Fruit Bunch (OPEFB) fiber as an affordable, abundant, and biodegradable alternative filler for NR. However, compatibility issues arise between the nonpolar NR and the polar OPEFB fiber. A latex-starch hybrid coupling agent (CA (NR-St)) was added to the composite formulation to address this. NR, OPEFB fiber, and the coupling agent were mixed using an open roll mill with a 10 phr OPEFB …

Separation Of Organic Acids Through Direct Catalysis From Sugars, Katelyn Robinson

Chemical Engineering Undergraduate Honors Theses

Society relies on plastic products, whether they are single use or durable. A downside of plastic is that the most common type is a product of oil and oil is not only a limited resource but also a climate-damaging resource. Polylactic acid (PLA) is a bio-based, biodegradable plastic. However, the process of converting biomass to polylactic acid polymer has the largest environmental impact of the PLA production process, so alternative methods of conversion are needed (Moretti et al., 2021). The polylactic acid polymer can be made with lactic acid, which can be converted from glucose.

The Influence Of Diamine Curing Additives On The Network Architecture Of Phthalonitrile Thermosetting Polymers, Tyler J. Richardson

Dissertations

Phthalonitrile monomers undergo diamine-promoted polymerization by a complex reaction mechanism involving two competitive cure pathways, forming two primary network architectures: linear polyisoindoline chains and branched triazine crosslinks. The influence of the diamine curing additive on the polymerization pathway, and the influence of the resulting network architectures on cured network properties, have not been adequately explored within the phthalonitrile field. Two structurally different diamine curing additives, bis[4-(3-aminophenoxy)phenyl] sulfone (mBAPS) and 1,3-phenylenebis((4-(4-aminophenoxy)phenyl)methanone) (AEK-134), were studied for the polymerization of resorcinol phenylphosphate phthalonitrile (RPPhPN), where the influence of diamine structure and concentration on the polymerization behavior, network architecture, and bulk thermal and thermomechanical …

Hydrothermal Liquefaction Of Saccharina Latissima For The Production Of Biofuel, Mayokun A. Oke

Mechanical Engineering Theses

We performed hydrothermal liquefaction of brown macroalga (Saccharina latissima) in the presence of homogenous and heterogenous catalysts such as KOH, Na₂CO₃, Pd/C, HZSM-5, Ce/HZSM-5, and Ni/SiO₂-Al₂O₃ in hot compressed water, to investigate their effects on product yield and composition in the biocrude. To investigate hydrocarbon production, we used methanol as co-solvent (methanol-to-water 1/4 vol.%) and as the only liquefaction solvent. We carried out the experiments in a batch reactor at 330^oC and 120-130 bar, and varying temperature, algae-to-water ratio, residence time, and pretreatment method. The biocrude yields …

Polyethersulfone Thin-Film Nanocomposite Membrane Embedded With Amine-Functionalized Graphene Oxide For Desalination Applications, Ahmed Bahaeldin

Theses and Dissertations

Thin-film nanocomposite (TFN) desalination membranes were prepared based on a polyethersulfone (PES) support, where the polyamide (PA) layer was embedded with amine-functionalized graphene oxide (GO). The effect of adding various concentrations of functionalized and un-functionalized GO on the desalination performance, hydrophilicity, and morphology of the membranes was additionally assessed throughout this work. Scanning electron microscopy (SEM) measurements were used to assess the morphology of the membranes in combination with Brunauer-Emmett-Teller (BET) analysis. Contact angle measurements were used to gauge the hydrophilicity of the synthesized membranes. The membrane with the best desalination performance contained 1x10^-3 wt/vol% of functionalized GO in …

Potential Of Biduri Fiber (Calotropis Gigantea) As Material For Oil Spill Absorbent, Anne Sukmawati, Wulan Septiani

Journal of Materials Exploration and Findings

Biduri fiber (Calotropis gigantea) is a natural hollow fiber with hydrophobic and oleophilic properties potentially used as oil spilled sorbent from seawater. This study aims to determine the absorption capacity and efficiency of the Biduri fiber and membrane to fuel oil. Measurement of oil absorption to seawater was carried out at various fiber weights (0.5-1.5 g), fiber composition (50-95%), contact time (10-90 minutes), temperature (30 and 50°C), and compared with commercial products. The results showed that the fiber weight variation of 0.5-1.5 g has an average absorption efficiency of 96.67%, and the highest absorption was obtained in a weight of …

The Application Of Photoelectron Spectroscopies In Analyzing The Impact Of Interfacial Energetics On Perovskite Solar Cells, Tuo Liu

Theses and Dissertations--Chemistry

In recent years, organic-inorganic metal halide perovskites (HP) have garnered tremendous attention in photovoltaic research. This attention is attributed to their low cost and excellent optoelectronic properties, including large absorption coefficients, tunable bandgaps, long charge-carrier diffusion lengths, and low densities of deep trap states. Inverted p-i-n architecture perovskite solar cells (PSCs) are of intense interest and are generally regarded as more amenable to low-temperature solution processing. Nevertheless, the development of inverted PSCs is lagging the conventional architecture devices. Imperfect energy level alignments and charge carrier recombination, especially at the interface between perovskite and electron transport layers (ETLs), are two main …

Bbt Acoustic Alternative Top Bracing Cadd Data Set-Norev-2022jun28, Bill Hemphill

STEM Guitar Project’s BBT Acoustic Kit

This electronic document file set consists of an overview presentation (PDF-formatted) file and companion video (MP4) and CADD files (DWG & DXF) for laser cutting the ETSU-developed alternate top bracing designs and marking templates for the STEM Guitar Project’s BBT (OM-sized) standard acoustic guitar kit. The three (3) alternative BBT top bracing designs in this release are
(a) a one-piece base for the standard kit's (Martin-style) bracing,
(b) 277 Ladder-style bracing, and
(c) an X-braced fan-style bracing similar to traditional European or so-called 'classical' acoustic guitars.

The CADD data set for each of the three (3) top bracing designs includes …

Large Area Projection Sintering Of Semicrystalline Polymers And Part Analysis Of The Printed Specimens, Taranjot Kaur

USF Tampa Graduate Theses and Dissertations

As the requirements posed to products have increased in recent years. The trend towards individualized serial products steps up the need for respective manufacturing techniques to be more and more flexible. Conventional techniques of serial production, such as injection molding, are unable to fully meet the requirements of this trend. Additive manufacturing techniques generate components directly from a CAD data set while requiring no specific mold, producing minimal waste, and reaching satisfactory geometric accuracy. This is how, as opposed to conventional techniques, they comply with these increased demands to processing technology. Over the last two decades, the research community has …

Bbt Side Mold Assy, Bill Hemphill

STEM Guitar Project’s BBT Acoustic Kit

This electronic document file set covers the design and fabrication information of the ETSU Guitar Building Project’s BBT (OM-sized) Side Mold Assy for use with the STEM Guitar Project’s standard acoustic guitar kit. The extended 'as built' data set contains an overview file and companion video, the 'parent' CADD drawing, CADD data for laser etching and cutting a drill &/or layout template, CADD drawings in AutoCAD .DWG and .DXF R12 formats of the centerline tool paths for creating the mold assembly pieces on an AXYZ CNC router, and support documentation for CAM applications including router bit specifications, feeds, speed, multi-pass …

A Modular Synthesis Of Processable And Thermally Stable Semi-Fluorinated Aryl Ether Polymers Via Step-Growth Polymerization Of Fluoroalkenes, Ketki Eknath Shelar

Theses and Dissertations

Tailored fluoropolymers remain the leading choice for a wide variety of advanced high-performance applications, including electronic/optical and energy conversion, owing to their unique blend of complementary high-performance properties. Amorphous semi-fluorinated polymers exhibit improved solubility and melt processability when compared to traditional perfluoropolymers. A leading class of semi-fluorinated aryl ether polymers includes perfluorocyclobutyl (PFCB), perfluorocycloalkenyl (PFCA), and fluoroarylene vinylene ether (FAVE) polymers. Monomers containing aromatic trifluorovinyl ethers (TFVE) are used to synthesize PFCB polymers via radical-mediated [2+2] cyclodimerization. On the other hand, FAVE and PFCA polymers are polymerized via base-mediated nucleophilic addition/elimination of bisphenols with TFVE monomers and decafluorocyclohexene respectively. The …

Extractive Membranes For The Detection And Screening Of Waterborne Plutonium, James Foster

All Dissertations

The development of rapid screening tools for special nuclear materials remains a crucial focus for nonproliferation efforts. Traditional approaches for the analysis of trace-level Pu isotopes in water requires tedious and time-consuming sample preparation steps that do not lend well to expeditious screening. Therefore, a novel analytical method that combines both Pu concentration and source preparation into a single detection system would make for an invaluable tool for nuclear security applications. Extractive membranes absorbers can help to fulfill this role as they are capable of concentrating Pu to detectable limits while subsequently serving as alpha spectrometry sample sources. In Chapter …

Synthesis And Molecular Processes Governing Self-Healing Polymeric Materials, Siyang Wang

All Dissertations

Self-healing polymers capable of recovering from physical damages are promising materials for advanced technologies. In these studies, we developed routes to achieve self-healable properties in acrylic-based copolymers that rely on non-covalent dipolar interactions present in essentially all polymeric materials. Using a combination of spectroscopic tools, thermo-mechanical analysis, and molecular dynamic (MD) simulations, these studies have shown that dipolar interactions lead to conformational changes of macromolecular segments which, in turn, result in self-healing without external intervention. This dissertation also describes the development of novel self-healable acrylic-based covalent adaptable networks (CANs) that combine reprocessing and self-healing properties. The utilization of dipolar interactions …

Simplified Synthesis Of Conjugated Polymers Enabled Via 1,4-Dihydropyrrolo[3,2-B]Pyrrole, Kenneth-John Jack Bell

Master of Science in Chemical Sciences Theses

Conjugated polymers have attracted significant attention as the active layer material in organic electronics, such as organic photovoltaics and light-emitting diodes, partly due to the ability to influence a broad range of properties through structural design motifs. However, high performance conjugated polymers suffer from numerous synthetic steps, generation of toxic waste, and harsh reaction conditions all of which impart additional costs that inhibit their widespread utilization. Therefore, an emphasis on reducing synthetic complexity and utilizing abundant, commercially available starting materials is needed for organic electronics to reach their full potential. Dihydropyrrolo[3,2-b]pyrrole (H₂DPP) chromophores offer a simple one-pot synthesis …

Block Copolymer Directed Self-Assembly: Exploring The Efficacy Of Applications In Semiconductor Fabrication, Jakin Bryce Delony

USF Tampa Graduate Theses and Dissertations

Over the course of the past 80 years, semiconductor devices have become increasingly ubiquitous in everyday life.From constructing mainframes that encompassed entire rooms during the 1940s, to inventing personal computers in the 1980s, to developing progressively faster smartphones and wearable technology in the 2010s, the primary driving force behind the Digital Revolution has been increasing transistor counts, and thus computing power, via incremental improvements in optical lithography. In 1965, Intel co-founder Gordon Moore boldly predicted that the transistor density of semiconductor devices would double approximately every 18-24 months. While this prediction -- now colloquially referred to as Moore's Law -- …