Physical Chemistry Commons^™

Investigation Of Electrochemical Noise In The Crevice Corrosion Of Q235 Carbon Cteel, Qian Hu, Yu-Bing Qiu, Xing-Peng Guo

Journal of Electrochemistry

The crevice corrosion behavior of Q235 carbon steels in a NaHCO₃+NaCl solution was investigated by electrochemical noise(EN) and electrochemical impedance spectroscopy(EIS).Three stages of crevice corrosion including the induction,the rapid transform and the stable development could be clearly distinguished.The characteristics of the electrochemical noise and the noise resistance Rn showed remarkable differences at each stage.The electrode area ratio(r) of outside to inside the crevice had a significant influence in the development of crevice corrosion.The time of the induction stage increased with increasing r.However,under the stable development stage of the crevice corrosion,the surface outside the crevice was at an active …

Effect Of Naphthalene Water Reducer On Corrosion Behavior Of Reinforcing Steel In Concrete, Yu-Ming Tang, Jie Zhang, Yu Zuo

Journal of Electrochemistry

The influence of naphthalene water reducer on corrosion behavior of reinforcing steel in concrete was studied by the methods of corrosion potential measurement,linear polarization and EIS test.The values of concrete resistance(Rc) and polarization resistance(Rp) of the samples with naphthalene water reducer were higher than those without naphthalene water reducer,especially in the concrete with 0.2 percent naphthalene water reducer.A suitable amount of water reducer can improve the pore structures of concrete,increase the concrete compactness and impermeability,and decrease corrosion rate of rebars in concrete.

Effect Of Electrochemical Property Of Uns J91450 Stainless Steel On Stress Corrosion Cracking In Hydrogen Sulfide Solutions, Zhi-Yong Liu, Chao-Fang Dong, Xiao-Gang Li, Li-Xian Wang

Journal of Electrochemistry

Effect of electrochemical behaviours on stress corrosion cracking(SCC) of UNS J91450 stainless steel in hydrogen sulfide environment was investigated using slow-strain-rate test(SSRT) and electchemial techniques.Results show that UNS J91540 stainless steel was susceptible to SCC in varying H₂S solutions,and the SCC susceptibility reduced with the increase of pH value.The electrochemical property plays an important role in the SCC occurrence,as a combined effect of hydrogen embritlement and anodic dissolution at SCC cracktip at open circuit potential.In the solution with a lower pH the hydrogen revolution was intensive and the cracktip anodic dissolution was weaker,however,in the higher pH solution the …

Developments Of Scanning Electrochemical Probes And Their Applications In Studying Of Localized Corrosions, Chang-Jian Lin, Yan Li, Bin Lin, Rong-Gang Hu, Min Zhang, Xiang-Dong Zhuo, Rong-Gui Du

Journal of Electrochemistry

The electrochemical inhomogeneities always exist at the interface of metal/solution,and play an important and often controlling role in localized corrosion of metals in a given environment.It is necessary to develop in situ imaging techniques for further studying the electrochemical and environmental inhomogeneities at the interface of metal/solution for the localized corrosion system.In this paper,various techniques with spatial resolution,such as scanning micro reference electrode(SMET),scanning electrochemical microscope(SECM),atomic force microscope(AFM),and scanning Kelvin probe(SKP),and their applications in corrosion studies were briefly reviewed.The chemical probes and array electrode have been developed.It was concentrated to describe our newly developed techniques of the scanning electrochemical probes,including SMET …

Preparation And Electrochemical Properties Of Layered Manganese Oxide(Li-Birnessite Type), Xing-Kang Huang, Hai-Tao Chang, Jian-Long Gan, Qing-Shun Zhang, Hong-Jun Yue, Dong-Ping Lv, Yong Yang

Journal of Electrochemistry

Layered Li-birnessite was prepared by means of oxidizing Mn²⁺ with O₂ gas in alkaline media.The as-prepared sample was characterized by scanning electron microscopy(SEM), X-ray diffraction(XRD), BET and thermogravimetric/diffenential thermal analysis(TG/DTA) techniques. The electrochemical properties of the material were also investigated. The results show that such a Li-birnessite consists of well-crystallized spherical particles with an interlayer distance of 0.70 nm. The Li-birnessite delivered a high discharge capacity of 203 mAh/g at a rate of 0.2 C(40 mA/g), and had good rate capability as well.

Electrochemical Behavior Of Mg-Li Electrodes In Nacl Solution, Lin Wu, Yan-Zhuo Lv, Xue Cao, Gui-Ling Wang, Dian-Xue Cao

Journal of Electrochemistry

The Mg-Li electrodes containing 8.5% and 14% Li were prepared using an induction melting method. Their electrochemical behavior in NaCl solution was investigated by means of potentiodynamic polarization, potentiostatic oxidation,electrochemical impedance technique and mass-loss measurements. The morphology of the electrodes after discharge was examined using scanning electron microscopy. The Mg-14Li electrode showed more negative open circuit potential and higher discharge current density than Mg-8.5Li electrode. The oxidation products of Mg-14Li loosely attached on the electrode surface and peeled off easily. The Mg-8.5Li exhibited higher utilization efficiency. Both electrodes gave higher utilization efficiencies when discharged at lower anodic potential.

Electrochemical Performance Of The Exfoliated Graphite Containing Sulfur Cathode Material For Lithium Sulfur Battery, Ke-Guo Yuan, Wei-Kun Wang, Zhong-Bao Yu, An-Bang Wang

Journal of Electrochemistry

The exfoliated graphite containing sulfur cathode material was prepared by the high temperature sulfur gas diffusion adsorption method.This cathode material could obtain an initial discharge specific capacity 972 mAh·g^-1,capacity retention ratio 78% and cycling efficiency above 80%,respectively.The exfoliated graphite containing sulfur cathode could decrease the reaction interphase charge transfer impedance,and restrain the sulfur or polysulfide shuttle phenomenon during the charge-discharge process through improving the diffusion impedance.

Effects Of Kscn On Kinetic Characters Of The Positive Couple And Performance For Vanadium Redox Flow Battery, Jian-Guo Liu, Dong Shi, Yue Men, Chuan-Wei Yan

Journal of Electrochemistry

In order to improve the reaction activity of VO²⁺/VO²⁺ and the battery performance of Vanadium redox flow battery,different concentration of potassium sulfocyanates KSCN were added into 0.1mol/L VOSO₄/ H₂SO₄ solution,and the kinetic characters of electrochemical reaction of VO²⁺/VO²⁺ was studied by CV and EIS.The results showed that the addition of KSCN could improve the oxidative peak current value of positive couple VO²⁺/VO²⁺ reaction,but had little influence in the reductive peak.The addition of KSCN decreased the impedance at 1.0 V.And the value of standard rate constant k0 …

Effect Of Impurity Cu(2+) On Oxygen Electrode In Pemfc, Xiao Jie, Jun-Bo Hou, Zhi-Gang Shao, Bao-Lian Yi

Journal of Electrochemistry

Rotating disk electrode was adopted in this paper to simulate the cathode in PEMFC.In the Cu²⁺ electrolyte,the influence of impurity Cu²⁺ on Carbon-Supported Pt Catalysts was investigated by using electrochemical measurements such as chronocoulometry,cyclic voltammetry and linear sweep.Experimental results showed that,after constant voltage at 0.49 V,the ECA of Pt/C decreased dramatically,it's perhaps under potential deposition of Cu might occur on the substrate.Meanwhile the change of ORR Tafel scope reaction is very large.It might be because oxygen adsorption sites are occupied by Cu atoms after they under potential deposit on surface of Pt/C catalyst,and the adsorption of oxygen on …

Electro-Oxidation Of Methanol On Fe-Doped Pt-Zro2/C Catalyst, Mao-Cai Lin, Dong-Dong Liu, Qing-Chun Yu, Ming-Ruo Hu, Heng-Yong Tu

Journal of Electrochemistry

The Fe-doped ZrO₂ powders were prepared by so-gel method.After that,Pt-Zr_1-xFe_xO₂/C catalysts were made by reducing platinum salts with ethylene glycol.The physical property of the catalyst was characterized by XRD and TEM.It was found that the distribution of the catalyst was narrow,the particle sizes of Pt and ZrO₂ particles were 2~4 nm and 3~7 nm,respectively.The Cyclic Voltammetry and Chronoamperometry testing indicated that the electro-catalytic activity for methanol electro-oxidation on Pt-ZrO₂/C catalyst increased when ZrO₂ was doped with Fe.And Pt-Zr_0.95Fe_0.05O₂/C catalyst showed the highest activity …

Investigation On Electrogenerated Active Chlorine From Diluted Nacl Solutions At Ti/Pt Anode, Hao Shen, Jin-Hong Fan, Lu-Ming Ma

Journal of Electrochemistry

Electrogeneration of active chlorine from diluted NaCl solutions was investigated in an undivided cell with Ti/Pt anode and Ti plate cathode.The effects of electrolysis time,current density(i),chloride concentration and pH value on the electrogeneration of active chlorine and current efficiency(CE) were analyzed.Meanwhile,the changing trends of the electrolyte's conductivity(TSD) and pH value in the electrolysis process were discussed.The results showed that the concentration of active chlorine increased with electrolysis time,but the trend became slow.During this process,the current efficiency reduced steadily.When i was 4.93～7.39 mA/cm²,the concentration of active chlorine increased with the increase of i,but no longer increased when the i …

Influence Of Nano-Al2O3 Particles In Nickel Electro-Crystallization Process, Cheng-Yu Tan, Wei Hu, Hang Cui, Yu Liu

Journal of Electrochemistry

The influence of nano-Al₂O₃ particles in nickel electro-deposition on copper matrix from acid sulphate solution was studied under various potentials by using cyclic voltammetry(CV) and chronoamperometry(CA).The results show that the beginning potential of electro-deposition was about-740 mV(vs.SCE) for Ni-Al₂O₃ solution system.With the step-potential moving to the negative direction,the nucleation time of electro-deposition for Ni-Al₂O₃ solution system was shortened gradually.Compared with that of pure Ni deposition system,the nucleation time tm,corresponding to the peak current of Ni-Al₂O₃ deposition system was apparently shortened under the lower step-potential:-740~-830 mV,which indicates that Al …

Investigation Into Select Isoquinolines As A Putative Causal Agent Of Ethanol Addiction In Mammals, Jacob Christopher Strawbridge

Dissertations

Alcohol is the most abused drug in America today. The neurological root of the problem is still a much debated subject and many differing views exist on the nature of alcoholism, be it a social dysfunction or a neurochemical imbalance. Some researchers have proposed that a skewed metabolism of dopamine that results in the formation of tetrahydroisoquinoline (THIQ) alkaloids plays a major role in the neurochemical acquisition and maintenance of alcohol addiction. In an effort to better understand the relationship of THIQ's to alcohol addiction, a series of experiments have been conducted. The chiral separation via high pressure liquid chromatography …

The Rotational Spectrum Of The Fed Radical In Its X4Δ State, Measured By Far-Infrared Laser Magnetic Resonance, Michael Jackson, Lyndon R. Zink, Jonathan P. Towle, Neil Riley, John M. Brown

All Faculty Scholarship for the College of the Sciences

Transitions between the spin-rotational levels of the FeD radical in the v = 0level of the X ⁴Δ ground state have been detected by the technique of laser magnetic resonance at far-infrared wavelengths. Pure-rotational transitions have been observed for the three lowest spin components. Lambda-type doubling is resolved on all the observed transitions; nuclear hyperfine structure is not observed. The energy levels of FeD are strongly affected by the breakdown of the Born–Oppenheimer approximation and cannot be modeled accurately by an effective Hamiltonian. The data are therefore fitted to an empirical formula to yield term values and g-factors for …

A Theoretical Study Of Methanol Oxidation Mechanisms By Methanol Dehydrogenase Enzymes For Fuel Cell Applications, Nagesh B. Idupulapati

Doctoral Dissertations

Enzymes are considered for electrochemical generation of power in fuel cells. Methanol dehydrogenase (MDH) is one such enzyme, which has been used as an anodic catalyst for a methanol-fed biofuel cell producing enough power for small electronic device applications. In practice, however, there are power output limitations associated with this MDH fuel cell, which may potentially be eliminated or reduced if the reactivity of this enzyme during the oxidation of methanol at the molecular level is clearly understood.

Two mechanisms for the methanol oxidation process by MDH have been proposed in the literature, Addition-Elimination (A-E) and Hydride Transfer (H-T), but …

Computational Study Of Pristine And Titanium-Doped Sodium Alanates For Hydrogen Storage Applications, Gopi Krishna Phani Dathar

Doctoral Dissertations

The emphasis of this research is to study and elucidate the underlying mechanisms of reversible hydrogen storage in pristine and Ti-doped sodium aluminum hydrides using molecular modeling techniques. An early breakthrough in using complex metal hydrides as hydrogen storage materials is from the research on sodium alanates by Bogdanovic et al., in 1997 reporting reversible hydrogen storage is possible at moderate temperatures and pressures in transition metal doped sodium alanates. Anton reported titanium salts as the best catalysts compared to all other transition metal salts from his further research on transition metal doped sodium alanates. However, a few questions remained …

Q-Switched And Mode Locked Short Pulses From A Diode Pumped, Yb-Doped Fiber Laser, Seth M. Swift

Theses and Dissertations

A diode-pumped, ytterbium (Yb)-doped fiber laser system was designed and demonstrated to operate in continuous wave (cw), passively Q-switched and possibly passively mode locked operation. To our knowledge, this was the first fiber laser oscillator built at the Air Force Institute of Technology. A Cr⁴⁺:YAG (Chromium: Ytterbium Aluminum Garnett) crystal was used as a saturable absorber to generate Q-switched pulses. Attempts to mode lock the laser were performed using a semiconductor saturable absorber mirror (SESAM) and through nonlinear polarization rotation (NPR). The best output power result was 5 Watts (W) while pumping at 8.3 W, yielding 60% efficiency …

Beta-Peptides With Improved Affinity For Hdm2 And Hdmx, Elizabeth A. Harker, Douglas S. Daniels, Danielle A. Guarracino, Alanna S. Schepartz

Chemistry Faculty Publications

We previously described a series of 314-helical β-peptides that bind the hDM2 protein and inhibit its interaction with a p53-derived peptide in vitro. Here we present a detailed characterization of the interaction of these peptides with hDM2 and report two new β-peptides in which non-natural side chains have been substituted into the hDM2-recognition epitope. These peptides feature both improved affinity and inhibitory potency in fluorescence polarization and ELISA assays. Additionally, one of the new β-peptides also binds the hDM2-related protein, hDMX, which has been identified as another key therapeutic target for activation of the p53 pathway in tumors.

The Effect Of Sintering Time On The Performance Of Spherical And Nano-Sized Lifepo4 Cathode Material, Zhong-Qiang Shan, Guo-Zeng Wang, Di Tian, Jian-Hua Tian

Journal of Electrochemistry

The spherical LiFePO₄ with nano-size is expected as an important direction for LiFePO₄ cathode materia1.With the method of liquid co-deposited-carbonthermal reduction,we prepared spherical LiFePO₄ cathode material with nano-size and we put our emphasis on the effect of sintering time on the material.By XRD,SEM,TEM and charge & discharge analysis,we found the sample sintered at 550 ℃ for 10 hours showed the best electrochemical properties and good degree of sphericity,with the size of 40～100 nm.

Preparation And Performance Of Co And La Co-Doped Li-Rich Lithium Manganate, Da-Qiao Zhou

Journal of Electrochemistry

The cathode material of Li_1.1Co_0.02La_0.01Mn₂O₄ was successfully synthesized by the method of co-precipitation followed by a solid state reaction.In the sintering temperature range of 700～850 ℃,X-ray diffraction(XRD) results showed a single phase of each material and the increase of crystallization degree,and scanning electron microscopic(SEM) images indicated that the particle size increased and the specific surface area decreased,respectively,with increasing the sintering temperature.Due to its lower polarization resistance,the Co and La co-doped lithium-rich lithium manganate(sintered at 800 ℃) positive electrodes showed the most promising electrochemical performance.The capacity retention after 50 cycles reached 98.5%.

Electrochemical Properties Of Functionalized Carbon Nanotubes And Their Applications In Analysis Of 6-Mercaptopurine, Bao-Yi Lu, Yan-Yan Lai, Hong Li

Journal of Electrochemistry

The electrochemical behaviors and adsorption properties of single-walled carbon nanotubes such as SWNT,SWNT-COOH,and SWNT-OH and multi-walled carbon nanotubes including MWNT,MWNT-COOH,and MWNT-OH modified at a graphite electrode have been investigated by using [Fe(CN)₆]^3-anion and [Co(phen)₃]³⁺ cation.It was shown that shows good redox reversibility of [Fe(CN)₆]^3-/4-reactions on the existed carbon nanotubes(CNT) modified electrode.Based on the strong adsorptive property of [Co(phen)₃]³⁺ on the CNT surface,the [Co(phen)₃]³⁺/CNT modified graphite electrode can be obtained by progressive potential sweeping and developed to monitor quantitatively 6-mercaptopurine(6-MP).The adsorption capacity of …

High Utilization Aupt Nanoparticles Supported On Mwcnts For Methanol Electro-Oxidation In Alkaline Medium, Xun Guo, Dao-Jun Guo, Xin-Ping Qiu, Li-Quan Chen, Wen-Tao Zhu

Journal of Electrochemistry

We synthesized gold-platinum electrocatalysts supported on multi-walled carbon nanotubes(MWCNTs) with high utilization by a simple one-step method.A high Pt loading series of bimetallic AuPt/MWCNTs catalysts were prepared by the improved ethylene glycol reduction method,and then were compared in terms of the electrocatalytic activity for methanol electro-oxidation using cyclic voltammetry(CV) and chronoamperometry in alkaline solutions.The structure of AuPt/MWCNTs was characterized by the transmission electron microscopy(TEM),X-ray diffraction(XRD) and energy-dispersive X-ray spectroscopy(EDS).The results showed that the AuPt/MWCNTs catalysts had high Pt utilization,uniform AuPt nanoparticles size and good electrocatalytic activity for methanol electro-oxidation.The effect of Au/Pt mass ratio on electrocatalytic activity was also investigated.The …

A Conducance Detection System Applying Constant Current Source For Ion Chromatography, Hua-Bin Chen, Wei-Xiong Huang, Rong-Zong Hu

Journal of Electrochemistry

Being different from bipolar pulse technique,a new type conductivity detection circuit system applying constant current source for ion chromatography was designed which effectively reduces the complexity of bipolar pulse technique,accurately and intelligently completes the signal amplification,collection,processing and spectrum displaying.In this article the detection principle and the hardware of the system were described and the experimental results with accurate and reliable measurements were shown.

Preparation And Electrochemical Performance Of Li3V2(Po4)3, Hou-Gang Fan, Tao Jiang, Chun-Zhong Wang, Gang Chen, Ying-Jin Wei

Journal of Electrochemistry

The carbon coating Li₃V₂(PO₄)₃ powder samples were synthesized by carbon incorporation solid state reaction.The structure,morphology and electrochemical properties have been studied by X-ray powder diffraction,scanning electron microscopy and automatic battery tester system,respectively.Carbon coating on Li₃V₂(PO₄)₃ would prevent the particles from agglomerating,reduce the particle size,raise the conductivity and improve the samples′ electrochemical performance.

Silicon Nanowires As Anode Materials For Lithium Ion Batteries, Yan-Peng Fu, Hui-Xin Chen, Yong Yang

Journal of Electrochemistry

The SiNWs electrodes were fabricated by coating and direct growth methods,respectively.The structure,morphology and electrochemical performance of such materials were characterized by XRD,SEM and charge-discharge tests.The results show that the electrodes prepared by direct growth method had higher capacity,better battery life and also displayed and excellent cyclability at higher currents.During the process of lithiation,the initial crystalline Si transformed to amorphous LixSi,and the average diameter of the SiNWs increased.Despite the large volume changed,the SiNWs remained intact and did not break into smaller particles.

Electrocatalytic Reduction Of Oxygen On Tungsten Carbide Electrode, Chun-An Ma, Yun Huang, Ying-Hong Zhu, Zhao-Yang Chen

Journal of Electrochemistry

Tungsten carbide(WC) catalysts were prepared by gas-solid reaction using ammonium metatungstate as precursors which were pretreated with spray drying sphere miniaturation,carbon monoxide as carrier gas and hydrogen as deoxidizing gas.The WC electrode was fabricated using WC catalyst powders and PTFE as binding agent,and characterized by XRD and SEM.Electrocatalyst behavior of WC for oxygen reduction reaction in the sulphuric acid solution was studied by steady-state voltammetry and cyclic voltammetry.The results show that the WC powders obtained were in spheric particles and the prepared WC electrode had a good electrocatalyst activity to the oxygen reduction reaction.The electrode reaction was controlled by adsorption.The …

Nano-Sn/Hard Carbon Composite As Anode Material For Lithium Ion Batteries, Bing-Kun Guo, Jie Shu, Kun Tang, Ying Bai, Zhao-Xiang Wang, Li-Quan Chen

Journal of Electrochemistry

The tin(Sn) nano particles were embedded into the mesopores of hard carbon spherules(HCS) to form a composite anode material for lithium ion batteries.The structure of the obtained composite was characterized by X-ray diffraction(XRD) while its electrochemical performances were evaluated with galvanostatic cycling.It is found that the embedding Sn nanoparticles into porous HCS not only result in a composite material with high lithium storage capacity and capacity retention,but also increase the initial coulombic efficiency of the composite.Based on the infrared spectroscopic analysis,the enhanced initial coulombic efficiency is attributed to the inductive decomposition of the ROCO₂Li species in the solid …

19th International Symposium Of Fine Chemistry And Functional Polymers (Fcfp-Xix) & Iupac 5th Internaitonal Symoposium On Novel Materials And Synthesis (Nms-V), Editorial Office Of J.Electrochem.

Journal of Electrochemistry

No abstract provided.

Information Of The Electrochemistry And Relative Science & Technique Conferencein China, Editorial Office Of J.Electrochem.

Journal of Electrochemistry

No abstract provided.

Preparation Of The Protic Ionic Liquid/Pvdf-Hfp Composite Membranes And Its Performance For Dmfc, Rui-Ying Miao, Jian-Ling Li, Yong Fang, Xin-Dong Wang

Journal of Electrochemistry

The protic ionic liquid(PIL) α-methyl pyridinium trifluoroacetate([α-MPyH]Tfa) was synthesized by acid & alkali neutralization.Then PIL/PVDF-HFP composite membranes were prepared by means of phase inversion method using acetone as solvent.The conductivities of the composite membrane increased with the temperature and reached 8×10^-3 S/cm,1×10^-2 S/cm and 3×10^-2 S/cm at room-temperature,30 ℃ and 80 ℃,respectively,by electrochemical impedance method.The properties of the methanol-rejecting of the membranes were measured by chronoamperometry as well.The results indicate that the properties of methanol-resistance of the membranes before and after IL combination were equivalent approximately.