Physical Chemistry Commons^™

Electrodeposition Of Copper Into Trenches Under Rotating Hydrodynamic Condition, Jian-Jun Sun, Bu-Gao Xie, Wen-Hui Yin, Guo-Nan Chen

Journal of Electrochemistry

Silicon chips patterned with treneches were fixed onto a rotating electrode. Copper was electrodeposited into the trenches under rotating hydrodynamic conditions The sizes of the trenches are 1 m in height and 0.35 m, 0.50 m and 0.70 m in width, respectively. The effects of rotating of the chip, the current density and the concentration of Cu²⁺ on the filling of thetrenches were studied. It is found that lower current density and moderate concentration of Cu²⁺ resulted in a void free filling of the trenches.

Two Kinds Of Polarons Observedin Polyaniline In Aqueous H2So4, Qin Zhou, Lin Zhuang, Jun-Tao Lu

Journal of Electrochemistry

Simultaneous electrochemistry electron spin resonance (ESR) conductance measurements were carried out on electropolymerized polyaniline and ESR spectra were obtained with high signal/noise ratio. Spectral simulation revealed that in the early stage of polymerization, there were two kinds of polarons. According to the potential dependence of the ESR line width and the corresponding conductivitychange of the polymer, the two polarons are thought to be in ordered and disordered domains, respectively. With increasing doping level, the two polarons underwent similar transfer from Curie spin to Pauli spin and both polarons were charge carriers in the conducting polymer. This deduction was further supported …

Electrochemical Lithium Insertion Of Nanosized Tio2, Ying Lan, Jian-Wen Liu, Xue-Ping Gao, Xing-Di Zhou, Jin-Qiu Qu, Feng Wu, De-Ying Song

Journal of Electrochemistry

The protonic titanate nanotubes with the diameter of 10～15 nm were synthesized via hydrothermal method in NaOH solution and the calcined nanotubes at 500 ℃ were transferred to anatase nanorods with the diameter of 12～20 nm due to dehydration.The electrochemical behavior of the anatase nanorods as lithium insertion materials was examined. The results showed that the nanorod electrode had the high initial discharge capacity of 232 mAh/g and second reversible capacity of 198 mAh/g. The capacity of nanorod electrode maintained 152mAh/g after 20 cycles.

Electrocatalytic And Lifetime Studies Of Commercial Catalystsin A Pemfc, Cheng Xuan, Yan-Yun Ma, Li Qi, Cheng Peng, Ling Chen, Jun Zhao, Ying Zhang, Qin-Bai Fan

Journal of Electrochemistry

A particularly designed H-type cell was used to simulate the operating condition of a hydrogen-air proton exchange membrane fuel cell (PEMFC). The electrocatalytic activity, morphology, structure and lifetime of commercially available catalysts, carbon support platinum (Pt/C) and unsupported platinum-ruthenium (Pt-Ru), were preliminary studied by carrying out electrochemical measurements and by SEM, XRD techniques. The catalysts were simultaneously tested in the H-cell under operation, and also separately tested in a conventional electrochemical cell for comparison. It was found that the characteristic peaks of hydrogen adsorption/desorption on cyclic voltammograms shifted considerably to a more positive direction for Pt/C, while a more negative …

Direct Electron Transfer Of Redox Proteins And Enzymes Promoted By Carbon Nanotube, Chen-Xin Cai, Jing Chen

Journal of Electrochemistry

The redox proteins (enzymes), such as hemoglobin (Hb), horseradish peroxidase (HRP) and glucose oxidase (GOx) were immobilized on the surface of the carbon nanotube modified with glassy carbon (CNT/GC) electrode, respectively. The experimental results showed that the redox proteins (enzymes) underwent effective and stable direct electron transfer reaction at the surface of CNT/GC electrode with a pair of nearly symmetrical redox peaks in phosphate buffer solution. The formal redox potential, E^0' , is almost independent on the scan rates, the average value of E^0'  for Hb, HRP and GOx is -0.343±0.001, -0.319±0.002 and -0.456±0.001 V (vs.SCE,pH 6.9), respectively. …

Exceptional Electrochemical Activities Of Amorphous Fe-B And Co-B Alloy Particles Used As High Capacity Anode Materials, Ya-Dong Wang, Xin-Ping Ai, Han-Xi Yang

Journal of Electrochemistry

Ultrafine amorphous alloy particles (UAAP) of Fe-B and Co-B were synthesized and tested for possible use as electroactive anode materials. It is found that unlike their parent elements, the alloy particles of transition metal (TM) and boron, the Fe-B and Co-B showed superior electrochemical activities when used as anodic materials in aqueous alkaline solution. The discharge capacities of Fe-B and Co-B electrodeswere observed to be 1200 mAh/g and 1100 mAh/g at moderately high rate of 100 mAh/g, respectively, much higher than the theoreticalcapacity of currently used zinc metal (820 mAh/g). The exceptional high capacities of the boride alloys were probably …

Stability And Electrochemical Performance Of Nio Cathode Modified By Zno Additive For Mcfc In Molten Carbonates, Bo Huang, Fei Li, Qing-Chun Yu, Gang Chen, Ke-Ao Hu

Journal of Electrochemistry

The ZnO/Ni composite cathode was fabricated by tape-casting method, which microstructures and phases were studied. The electrochemical behaviors of ZnO impregnated NiO cathodes were also evaluated in molten 62 mol%Li₂CO₃ + 38 mol%K₂CO₃eutectic at 650 ℃ by electrochemical impedance spectroscopy (EIS) as a function of ZnO content and immersion time. The ZnO impregnated nickel cathodes showed the similar porosity, pore size and morphology to the reference nickel cathode. The stability tests of ZnO impregnated NiO cathodes showed that the ZnO additive could dramatically reduce the solubility of NiO in a eutectic carbonate mixture …

Structures And Redox Activities Of Poly(M-Methoxyaniline), Yun-You He, Yi-Ting Xu, Li-Zong Dai, Jean-Yves Gal, Hui-Huang Wu

Journal of Electrochemistry

Poly(m-methoxyaniline), PmMAn, was prepared in the presence of HCl, p-toluene-sulfonic acid and perchloric acid. By using cyclic voltammetry, the effect of different acid dopant on electrochemical activities of PmMAn was studied. The results showed that perchloric acid is the best acid to prepare PmMAn with good electrochemical activities The FTIR spectra indicate that the acid radical anions have embedded into PmMAn molecularchain as counter-ion during synthetic process, and this great influences the redox activities of PmMAn. SEM and XRD measurements illustrate that PmMAn is characterized by its typical molecular crystalline being monoclinic.

Study On Electrochemical Properties Of Peo-Based Composite Polymer Electrolytes, Hong-Yan Du, Hu Cheng, Yong Yang

Journal of Electrochemistry

Composite polymer electrolytes were prepared by introducing nano-scale SiO₂ into PEO₈-LiClO₄ matrix. The ionic conductivity, lithium transference number and the electrochemical stability windows were measured. The phase component was evaluated with DSC techniques. The results showed that the introduction of nano fillers enhanced the ionic conductivity. It reached 4.3×10^-5 S·cm^-1 at 22 ℃. The conductivity enhancement of the composite polymer electrolytes is analyzed and proposed.

Study Of Anti-Corrosion Property On Poly(An-Co-Oas)/Epoxy, Qing-Wu Wang, Geng-Chao Wang

Journal of Electrochemistry

Polyaniline, polyanisidine and their copolymer poly(An-co-oAs) were synthesized via the solution chemical oxidative polymerization of aniline and anisidine in an acidic aqueous medium, and their properties and structure were characterized. The electrochemical method were applied to evaluate the corrosion behavior of tined iron uncoated or coated by polyaniline, poly(An-o-oAs), polyanisidine and poly(An-co-oAs)/epoxy blend in acid or saline aqueous solution. The result showed that with the increase of anisidine content, the solubility of polymers is improved apparently but their oxidation extent decreases accordingly. It is also founded that polyaniline, poly(An-co-oAs) and polyanisidine all have good anti-corrosion properties, and their anti-corrosion capacity …

Study On Reduction Process Of Electrolyic Manganese Dioxide In Situ By Ultraviolet-Visible Absorption Spectroscopy, Li-Cai Zhu, Zhong-Zhi Yuan, Wei-Shan Li

Journal of Electrochemistry

The concentrationsof soluble Mn(Ⅲ) species, during the reduction ofelectrolytic MnO₂ (EMD) in alkaline solution,have been monitored in situ by UV-visible spectroscopy. The concentration of Mn(Ⅲ) ion in solution changes with discharge time. The first electron discharge process of EMD can be described by three different steps: 1) the reduction of Mn⁴⁺ ions on the surface of EMD particles and the structural defect regions within the EMD, 2) the reduction of Mn⁴⁺ ions in ramsdellite, 3)the reduction of Mn⁴⁺ ions in pyrolusite. During the second electron discharge of EMD, the soluble Mn(Ⅲ) is reduced to Mn(Ⅱ) , …

Fundamental Chemistry Of U And Pu In The Tbp-Dodecane-Nitric Acid System, Kenneth Czerwinski, Byron Bennett

Separations Campaign (TRP)

The speciation of hexavalent U and tetravalent Pu will be examined in the TBP-dodecane-nitric acid systems. This topic is chosen based on data needs for separation modeling identified by the AFCI. Emphasis will be placed on studying the influence of nitrate and acetohydroxamic acid on U and Pu speciation as well as conditions where a third phase forms in the organic phase. The organic phase will be 30% TBP in dodecane. Equal volumes of aqueous and organic phase will be used. The speciation of the actinides in the aqueous and organic phase will be determined by a number of different …

Infrared Spectrum And Stability Of A Π-Type Hydrogen-Bonded Complex Between The Oh And C2h2 Reactants, James B. Davey, Margaret E. Greenslade, Mark D. Marshall, Marsha I. Lester, Martyn D. Wheeler

Chemistry

A hydrogen-bonded complex between the hydroxyl radical and acetylene has been stabilized in the reactant channel well leading to the addition reaction and characterized by infrared action spectroscopy in the OH overtone region. Analysis of the rotational band structure associated with the a-type transition observed at 6885.53(1) cm−1 (origin) reveals a T-shaped structure with a 3.327(5) Å separation between the centers of mass of the monomer constituents. The OH (v = 1) product states populated following vibrational predissociation show that dissociation proceeds by two mechanisms: intramolecular vibrational to rotational energy transfer and intermolecular vibrational energy transfer. The highest observed OH …

Synthesis Of Nanocrystalline Nickel-Zinc Ferrites Via A Microemulsion Route, Vuk Uskoković, Miha Drofenik

Pharmacy Faculty Articles and Research

Nanostructured NiZn-ferrites were synthesized using a low-temperature co-precipitation method within the reverse micelles of ternary CTAB/1-hexanol/water microemulsions. The influence of pH on the precipitation reaction was investigated. It was found that a higher pH resulted in more crystalline particles. Subsequent oxidation of the ferrous ions precipitate, which leads to the formation of spinel ferrites, is discussed. Diffraction-lines broadening and specific surface area measurements yielded an average particle size of ~ 3 nm. The saturation magnetization of the samples was 20 times smaller than for traditionally synthesized NiZn-ferrites, while the coercivities were 10 - 100 times larger than bulk NiZn-ferrites, which …

Immobilization Of Fission Iodine By Reaction With A Fullerene Containing Carbon Compound And Insoluble Natural Organic Matrix, Spencer M. Steinberg

Separations Campaign (TRP)

The recovery of iodine released during the processing of used nuclear fuel poses a significant challenge to the transmutation of radioactive iodine. During the first two years of this program the use of Fullerene Containing Carbon (FCC) compounds and Natural Organic Matter (NOM) as potential sorbents for iodine release from the reprocessing of nuclear fuel was examined. This work also included the development of bench-scale testing capabilities at UNLV to allow the testing of the FCC and NOM materials in a simulated process off-gas environment. In the final year of the project we will complete studies of FCC and NOM …

The Electrochemical Separation Of Curium And Americium: Quaterly Report January - March 2004, David W. Hatchett, Kenneth Czerwinski

Separations Campaign (TRP)

This research report outlines the current status and progress associated with the electrochemical separation of Curium and Americium.

Data collection and analysis of the Ce³⁺/Ce⁴⁺ redox couple in various supporting electrolytes has continued. All electrolyte systems were investigated at Pt, Au, and Glassy Carbon working electrodes. Analysis of these data was accomplished by performing appropriate background subtractions to reveal net peaks due to Ce redox behavior. Successful identification of the Ce redox couple was achieved with all electrolyte/electrode systems, although a decline in peak resolution was observed with increasing acid concentration. Optimal conditions in this experiment were …

Progress In Research For Biofuel Cell, Yue Bao, Xia-Qin Wu

Journal of Electrochemistry

In this article, research progresses of the biofuel cell in recent years were summarized. The operation principle and classification of the biofuel cells were described. The role of the mediator for promoting electron transfer in biofuel cells and the techniques for improving the electric properties of biofuel cells, such as output potential, were discussed with some attracting research instances. Finally, the choke points for research of biofuel cell were explored, and the application prospect of biofuel cells was forecasted.

An Electrochemical Study Of The Effects Of Chelating Agents And Additives On Electroless Copper Plating, Xin Gu, Zhou-Cheng Wang, Chang-Jian Lin

Journal of Electrochemistry

In this study, ethylenediaminetetraacetic acid disodium salt (Na₂EDTA), triethanolamine(TEA), and 2,2′-dipyridine were adopted as chelating agents or additives in the electrolyte for electroless copper plating, and formaldehyde (HCHO) was as the reducting agent. Linear sweep voltammetry was applied to analyze the polarization behavior. The peak current of formaldehyde oxidation which increased by the addition of 2,2′-dipyridine is beneficial to formaldehyde oxidation in a specific range of concentration, While TEA decreased the peak current of formaldehyde oxidation. Two cathodic peaks due to copper(Ⅱ)reduction of TEA chelatation and copper(Ⅱ)reduction of EDTA chelatation were examined. EDTA increased the reduction peak current …

Effect Of Thiourea On Nickel Deposition, Guang-Hui Hu, Hui-Huang Wu, Fang-Zu Yang, Sheng-Lin Wang

Journal of Electrochemistry

Effect of thiourea on nickel deposition at glassy carbon and nickel-deposited glass carbon electrodes was investigated with cyclic voltammograms and impetance-potential curves. It was found that the nucleation processes occurred at the glassy carbon electrode. However, this characteristics disappeared at the nicked-deposited glassy carbon electrode. It was suggested that the presence of thiourea hindered the nucleation processes, yet accelerated grain growth. Curves of impetance-potential could sensitively detect effect of thiourea on nickel depositon and reflect changes in rate-determining step with potential.

Preparation, Structure And Electrochemical Hydrogenation Of Carbon Nanotubes Supported Platinum Catalysts, Qing-Gang He, Xiao-Zi Yuan, Xian-Xia Yuan, Zi-Feng Ma

Journal of Electrochemistry

In this paper, Pt/CNTs catalyst was prepared and its electrocatalytic property was studied by obtaining cycling voltammetry curves (C-V) and Tafel curves. In addition, the XRD,XPS and TEM tests were carried out to determine the structure and composition of the catalysts. It can be found that the platinum loading has been increased significantly using a carbon nanotubes support. Dispersion of Platinum was better and gave more active sites. The electrochemical characteristic of Pt/CNTs was also more desirable than that of Pt/C catalys t(Johnson Matthey). In conclusion, carbon nanotubes can played a conspicuous role in "electrogenerative" processes of PEMFC hydrogenation reactor.

Study On The Electrochemical Impedance Spectroscopy (Eis) Of Al-Bronze At Different Anodic Potentials, Hui Yu, Sa-Ying Dong, Hai-Bo Xu, Ming-Xian Sun

Journal of Electrochemistry

The corrosion dissolution mechanism of Al-bronze has been investigated by Electrochemical Impedance Spectroscopy (EIS) at different anodic potentials. In the active region, the corrosion products are complex compounds of cupreous chloride and the diffusion of CuCl_2^- is the control process of electrochemical reaction. In the transition region, there exhibits two capacitance loops on EIS because CuCl and cupreous oxides films deposit on the electrode surface. In the limiting current region, an inductance loop appears on the EIS because the breakdown of the oxides film leads to serious pit corrosion.

Electrochemical Study On The Anodic Process Of Fes, Hong-Hui Xu, Hui Xu, Yong Du, Zhu Pan, Yun-He Zhang, Yu-De Shu

Journal of Electrochemistry

Ferrous sulfide (FeS) was synthesized with spectrum-pure Fe and S at high-temperature, and its anodic behaviors in the solution of 0.5 mol·L^-1 H₂SO₄ + 0.5 mol·L^-1 K₂SO₄ was studied by using voltage sweep and step voltage techniques. The effects of acidity on the anodic polarization curves of FeS were investigated. The transfer coefficient β and exchange current density I_0 in the anodic electrode process, and the solid diffusion coefficient D_Fe of Fe²⁺ in FeS were measured. And also the activation energies of anodic reaction at different voltages was also determined.

Substrates Made By Electrodeposition For Measuring Electrical Properties Of One Dimensional Nanomaterials, Jin-Xuan Liu, Juan Xiang, Zhong-Qun Tian, Bing-Wei Mao

Journal of Electrochemistry

A method to prepare alternating conducting/insulating substrates by electrodeposition-oxidation was established to facilitate I-E measurements of one-dimensional nanomaterial by CT-AFM. The prepared Au/CuO and HOPG/CuO substrates showed low roughness as well as high uniformity of the alternating conducting/insulating structure, Qualitative I-E measurements were performed on a single carbon nanotube attached to the two above-mentioned substrates, both showing metallic characteristics at room temperature and in air.

Study Of Sptfs/Ptfe Composite Membranes With Different Ews, Yong-Zhu Fu, Dan-Min Xing, Bao-Lian Yi, Hua-Min Zhang

Journal of Electrochemistry

In this paper, sPTFS/PTFE composite membranes for PEMFC were obtained by impregnating two kinds of sulfonated poly-α,β,β- trifluorostyrene resin with different EWs into the porous PTFE substrate membranes. Water uptake, proton conductivity, mechanical strength and fuel cell performance of these two composite membranes were measured. Water uptake and proton conductivity were greatly reduced and mechanical strength was increased by composition in comparison with homogeneous membranes. Under the operating condition: T_Cell=80 ℃, P_H2=0.2 MPa, P_O2=0.2 MPa, fuel cell performance of the two composite membranes were better than that of Nafion 115. The fuel cell performance …

Studies On The Mechanism Of Electroreduction Of Oxalic Acid, Yu-Zhan Li, Xin Liu, Rui-Sheng Hu, Deng-Ping Gu

Journal of Electrochemistry

The electroreduction mechanism of oxalic acid on Pb electrode in Na₂SO₄ solution were investigated using high scan rate cyclic voltammetry and chronoamperometry. The dynamic parameters for the first step electron transter reaction of oxalic acid electroreduction by were determined. The corresponding reduction peak potentials of oxalic acid, glyoxylic acid and glycolic acid in the cyclic voltammogranis obtained in the same condition were compared, and the intermediate reduction products of oxalic acid were suggested. The results showed that oxalic acid is weakly absorbed on the lead electrode.

Coulometric-Weighing Test Method And Its Application In Determination Of Tin Coating Mass For Electrolytic Tinplate, Xiu-Wen Dong, Yan Li, Jian-Guo Liu, Guo-Wei Lin

Journal of Electrochemistry

The coulometric-weighing test method was established and applied to determine the tin coating mass for electrolytic timplate. The effects of electric quantity, the current efficiency and the electrochemical equivalent in the coulometric test method were overcome. The inaccuracy in the determination of final point at the anodic dissolution curve in the weighing method was avoided when applied to the electrolytic timplate, higher accuracy was obtained, the SD is less than 0.04 g/m²,RSD is as small as 0.36%.

Electrochemical Character Of Water Containing Gel Electrolyte And Its Preliminary Examination In Lithium Water Cell, Jing-Dong Liu, Wen-Ji Wang, Xin-Zheng Yi

Journal of Electrochemistry

AC impedance technique has been used to characterize the system of poly(methyl acrylic acid)-poly(methyl acrylic lithiumate)-glycerol (referred to as GPE).The results showed that the conductivity of GPE increased with increasing both temperature and its water content.The glass transition temperature of GPE polymer could be lowered by water. Its conducting characteristic was just like liquid electrolyte,The electrolysis of GPE was almost the same as the electrolysis of water. Its composition voltage was about 1.50V. The GPE has been used to manufacture lithium water cell. When the graphite was used as cathode, the cell could discharge continuously for 2 hours under constant …

Template Synthesis Of Highly Ordered Monocrystalline Metal Nanowire Arrays By A Two-Step Ac Electrodeposition, Juan Xiang, Jing-Hua Tian, Zi-Mian Ni, Zhi-Feng Huang, Bo Liu, Zhong-Qun Tian

Journal of Electrochemistry

The monocrystalline metal nanowire arrays were prepared by using a two-step AC electrodeposition in porous anodic aluminum oxide (AAO) template. The growth mechanism of nanowires was discussed. As a result, it has been found that the second voltage pulse has a considerable effect on the pore-filling ratio, the uniformity and the crystal structure, whereas the initial voltage pulse affects only the pore-filling ratio. Using the two-step AC electrodeposition, a highly ordered monocrystalline metal nanowire arrays with a pore-filling ration above 95% can be easily obtained.

The Interaction In Doping Lithium Of Carbonaneous Anode In Lithium Ion Battery, Chang-Guo Chen, Hong-Min Zhang, Jia Chen, Dan-Mei Yu

Journal of Electrochemistry

The quantum chemical DV-X_α method was used to calculate the lithium-doped models from one-Li-dopant to LiC₆ and LiC₂. It was found that Li⁺ has an tendency to attract electrons from the carbon plane through the C₆ hexagons lying above or below it by the graph of charge-density difference. It was shown that LiC₆ can exist steadily,while LiC₂ can not exist steadily.

Study On Determination Of Iodine Ion At Chitosan Modified Glassy Carbon Electrode, Bin Liu, Xiang-Ying Sun, Jin-Rui Xu

Journal of Electrochemistry

In this paper, a chitosan modified glassy carbon electrode was prepared by the method of covalent-bond reaction, and the anodic stripping voltammetric characteristics of iodine on the modified electrode was studied. The results showed that the modified electrode has higher adsorption and selectivity for I^- , and the sensitivity for I^-  has been much improved in 0.1 mol·L^-1 KH₂PO₄ solution (pH=4.0). The anodic stripping peak current of I^- on the modified electrode varied linearly with I^-  concentration in the range of 2.0×10^-6～2.0×10^-3 mol·L^-1, and the detection limit …