Physical Chemistry Commons^™

Electrodeposition Of Cu-Co Multilayer Thin Films, Jiangyun Xue, Jixun Wu, Dejun Yang

Journal of Electrochemistry

A method has been developed to produce Cu-Co Multilayer from a single electrolyte by electrodeposition. The effects of the concentration of copper ions, current density and the speed of rotation were investigated, and the Cu-Co electrodeposition films were analysed by TEM, AES and X-ray diffraction. The results indicated that the film was alternating pure copper and coppercobalt alloy layers. If the content of copper in cobalt layer is to be small, the concentration of its ions in solution must be small and the rotation speed must be low.

The Inhibition And Desorption Behavior Of N,N-Dipropynoxy Methyl Amine Trimethyl Phosphonate In Hydrochloride Acid, Tianbao Du, Dianzhen Cao, Jiajian Chen, Chunan Cao

Journal of Electrochemistry

The performance of inhibition mechanism and desorption behavior of the N,N-dipropynoxy methyl amine trimethyl phosphonate for iron in hydrochloride acid were investigated by means of static polarization and electrochemical impedance spectroscopy technique. The data of the polarization curves were fitted by weak-polarization fitting technique.The results show that N,N-dipropynoxy methyl amine trimethyl phosphonate possesses high inhibiting efficiency and geometric blocking effect. It is also showed that this inhibitor obeys the Frendulich adsorption isotherm.With the increase of anodic potential, a low-frequency induce arc was observed.

A Study Of Ruo2-Co3O4-Tio2(60) Coating On Ti-Substrate For Chlorine Gas Evolution, Liguang Yao, Mingxian Wang

Journal of Electrochemistry

The chlorine gas evolution activity, electric conductivity, service life, microstructure and surface morphology of RuO₂-CO₃O₄-TiO₂(60) coating on Ti-subetrate were studied in 0～30 m/o CO₃O₄ range by steady-state pelarization, X-ray diffraction,TEM and SEM methods. Active surface area of the coating was also evaluated. The in fluences of coating composition, micrortructure and surface morphology on chlorine gas evolution activity and active surface area of the coating were discussed in detail. As a result, sole rutile-type solid solution of RuO₂, CO₃O₄ and TiO₂ which showed better …

Study On The Ionic Conductivity Of Comb Polymer Electrolytes, Liming Ding

Journal of Electrochemistry

A comb polymer (CP350) with oligo-oxyethylene side chains was prepared from methyl vinyl ether/maleic anhydride copolymer.The ionic conductivity of CP350/LiAsF₆ and CP350/LiAsF₆ complexes was studied as a function of temperature and [Li]/[EO] ratios. A equivalent circuit was given to interpret complex impedance spectra. At 25 ℃, the ionic conductivity maxima of the two systems are 1.38×10^-4, 8.32×10^-5 S/cm respectively. The appearance of the conductivity maxima has been interpreted as being due to the effect of microviscosity on ion transport. lonic conduction displays non-Arrhenius behaviour. The temperature dependence of ionic conductivity was attributed mainly to the …

Electrochemical Studies On Chemical Polishing Of Copper, Keping Han, Jingli Fang

Journal of Electrochemistry

Changes in specular reflectivity,weight loss,surface topograph and potential with time and current-potential curves during chemical polishing were determined. The results showed that chemical polishing was composed of the etching, polishing and pitting stage. The passivating film theory also applied to the chemical polishing.

The Effect Of Additive Ce4+ On The Properties Of Composite Coating Of Co-P-Ptfe, Jiaoning Tang, Ling Huang, Zhaoxong Xie, Shibing Yao, Shaoming Zhou

Journal of Electrochemistry

The effect of additive Ce⁴⁺ on the properties of composite coating of Co-P-PTFE was studied in this paper. The results show that additive Ce⁴⁺ can change the structures and properties of Co-P-PTFE composite coating. First, the surface of the compoite coating becomes smooth and the microhardness of the composite coating increased. Secondly, additive Ce⁴⁺ decreased the corrosion current lcorr of the composite coating in the solution of 3% NaCl and increased its property of anticorrosion. Finally additive Ce⁴⁺ can affect preferred orientation and grain size of composite coating of Co-P-PTFE. Preferred orientation of the composite varies …

Study On The Growth Process Of Lead Dioxide On Lead-Antimony Electrodes By Impedance Tracing Method, Guolin Wei, Hongxin Yang, Jiarong Wang

Journal of Electrochemistry

The growth process of PbO₂ formed by the oxidation of PbSO₄ in the anodic film on lead-(1,3,5,7)wt% antimony electrodes was investigated with impedance tracing method of single frequency and the current-time transient method. The influence of antimony on this process was studied.The simulation curves obtained for capacity-time transients fit the experimental results very well. It has been shown that the mentioned growth process is a two-dimentional instantaneous nucleation and growth process. Antimony will inhibit the growth of PbO₂ nucleus but enhance its nucleation.

The Relationship Between Ionic Conductivity And The Structure Of The New Polymer Electrolytes, Hongze Liang, Yongxiang Song, Liming Ding, Yuchen Qi, Lixia Li, Xiabin Jing, Fusong Wang

Journal of Electrochemistry

Ionic conductivity of polymer-eutectic composed of lithium perchlorate and lithium nitrate has been studied. The effects of eutectic and polymers upon the conductivities have been discussed.The lonic conductivity depends on the eutectic properties as well as the treatment method of samples.

The Role Of Written And Verbal Expression In Improving Communication Skills For Students In An Undergraduate Chemistry Program, Brian P. Coppola, Douglas S. Daniels

Chemistry Faculty Publications

Proofreading, editing, and critique, the customary assessment tools scientists use to evaluate professional journal articles, grant applications, and any other writing, can be applied equally well in introductory science instruction. Such feedback is, in fact, crucial to growth and development. When learning anything new, students and faculty alike rely heavily on sources other than themselves (‘external editors’) to assess their understanding as they develop self-assessment skills (or ‘internal editors’). Although they rarely describe it in these terms, faculty nonetheless assume that students have developed and refined their internal skills by the time they take examinations and write term papers. Unfortunately, …

Corosion Potential Imagingat The Interface Of Coating/Metal By A New Electrochemical Technique, Changjian Lin, Xiangdong Zhuo, Jidong Chen, Hui Wang, Rong-Zong Hu, Yi Song, Jian-Guang Tan

Journal of Electrochemistry

/

Problems On The Study Of Anodic Films On Pb In Sulfuric Acid Solution (Ⅱ), Houtian Liu, Qunzhou Wang, Yongqin Wan, Weifang Zhou

Journal of Electrochemistry

The conditions for the growth of the different phases in the anodic Pb(Ⅱ) film on Pb in sulfuric acid solution were discussed.

Status Of The Research And Development For Fuel Cell Technology Abroad, Naichao Li, Baolian Yi

Journal of Electrochemistry

Status of the research and development for fuel cell technology abroad was overviewed, and at the aim of accelerating the research and development for fuel cell technology in China, the corresponding stategy for our country was recommended.

Electroluminescent Property Of N Type Porous Si And Its Characterization By Xps And Lima, Guozheng Li, Chenqian Zhang, Qiang Zhang

Journal of Electrochemistry

The chemical composition and structure of electroluminescent porous Si(PS) on n-Si, prepared by photoelectrochemical etching method, were investigated by using XPS and LIMA. The results show that electroluminescence(EL) intensity depends on the formation potential of PS. The relation between EL property and the results of XPS and LIMA is also discussed.

In Situ Studies Of Copper Electrodepostion On Hopg By Using Ecstm, Zhaoxiong Xie, Bingwei Mao, Xiangdong Zhuo, Jiqian Mu, Zhaowu Tian

Journal of Electrochemistry

In this paper, copper electrodepostion on HOPG had been in situ studied by using a homebuilt electrochemical scanning tunneling microscopy (ECSTM). Three dimensional nucleation and subsequent growth of copper crystals were found as the initial stage of copper deposition on HOPG. In the case of lower overpotential or lower concentration of Cu²⁺ , the bulk deposited copper layer tended to form smooth terraces, and grow at the edge of steps. The terraces were stable to some extent, which made it possible to be observed with atomic resolution. At a higher overpotential, the crystal size of copper were somehow smaller. …

Statistical Mechanical Treatment For The Electrical Double Layer At Ities: Analysis Of Mvn Model, Jintian Wu, Shengpei Chen, Hui Wang, Wenduan Su

Journal of Electrochemistry

A statistical mechanical treatment for electrical double layer at the interface between two immiscible elecrolyte solution (ITIES) is presented by using grand canonical method based on the MVN model.

For the MVN model, the ITIES was represented by that the two space charge regions are separated by an inner layer of the oriented solvent molecules. Assuming that the ions were allowed to penetrated into the solvent compact layer over some distance, then the grand canonical partition function of the inner layer at ITIES can be given. While the mean field approximation is employed to estimate the interactive potential energy of …

A Study Of The Electroplated Fe-Cr-Ni Alloy Microstructure, Donglin Li, Jianping Liu, Fangzhou Guo, Jianrong Hua

Journal of Electrochemistry

The microstructure of the electroplated Fe-Cr-Ni alloys from the mixed carboxylic acid solution containing Cr(Ⅲ) and additives were determined with XRD and SEM. Experimental results showed that, under the experimental condition, the phase component, structure of Cu base electroplated Fe-Cr-Ni alloys had a critical thickness, which was 11 μm and a critical Ni content, which was 32%. Organic additives, formic acid or polyethylene Glycol, mainly affected the surface, cross section morphology of the electroplated Fe-Cr-Ni alloys. Adding Mo to the electroplated Fe-Cr-Ni alloys led to remarkable corrosion resistance in concentrated HCl.

Polarographic And Voltammetric Behaviour Of Complex Of Ciprofloxacin With Manganese, Jialing Zhang, Huizhi Fan, Jinghao Pan

Journal of Electrochemistry

In 0.1 mol·L^-1 NH₃NH₄Cl buffer solution (pH 9.2) ,a sensitive reduction peak of complex of ciprofloxacin (CPFX) with manganese (Mn) was obtained by single sweep oscillopolarograph. The peak potential (E_p) is -1.61 V (vs.SCE). The peak current (i_p) is proportional to the concentration of Mn(Ⅱ) over the range of 5×10^-6 ～2×10^-5 mol·L^-1. It is possible to be applied to the determination of Mn(Ⅱ). The polarographyic and voltammetric behaviour of complex was studied in detail. The ratio of CPFX∶Mn in the complex was 2:1. The electrode reaction mechanism …

Electrochemical Studies Of Zncl2 Urea Melts, Peng Liu, Qiqin Yang, Guankun Liu, Yexiang Tong

Journal of Electrochemistry

The electric conductivities of ZnCl₂ Urea melts were determined .The influences of temperature and concentration on the conductance have been studied. The cylic voltammetry, potentiostatic electrolysis and open circuit potential time curve after electrolysis, X-ray diffraction were used to investigate the electroreduction of Zn²⁺, electrodeposition of zinc on some electrodes in urea metal chlorides melt. The conductivity of urea-NaCl-ZnCl₂ melt can reach to over 30 ms·cm^-1 (125 ℃), and has a liner relationship with temperature from 108 to 140 ℃. The electroreduction of Zn²⁺ to zinc is reversible at one step, and CuZn_{5 …}

The Applications Of Poap Ni2+ Films Modified Electrode As Sensor For Alcohol, Bingzeng Hua, Wenyun Hu, Yanzhen Chen

Journal of Electrochemistry

POAP Ni²⁺ films modified electrode can electrocatalyzes significantly the oxidation of alcohol. The modified electrode can be used as the electrochemical sensor for the detection of alcohol. But the oxidation of alcohol is effected by the thickness of films、the concentration of nickel ion in films, pH of electrolyte, as well as temperative. All of those conditions have been studied in order to achieve stable response current during the oxidation of alcohol, and the relation between concentration and current has been made. At last the major characteristic parameters, such as the low limitation of concentration, the response time, the ability …

Surface Raman Spectra Of Pyridine And 2 Mercaptopyrimidine Adsorbed On Rough Nickel Electrode, Qunjian Huang, Jinsong Gao, Xiongwei Cai, Bingwei Mao, Mingsen Zheng, Zhongqun Tian

Journal of Electrochemistry

The Raman spectra of pyridine and 2-mercaptopyrimidine (2-MP) adsorbed on bare nickel electrodes roughened by a HNO₃ etching procedure have been obtained for the first time by utilizing a highly sensitive confocal Raman microscope. Their adsorption behaviours are discussed briefly. This primary result illustrates a great potential for in-situ Raman spectroscopy in the study of chemical and electrochemical processes of transition metal surfaces.

Electrocatalytic Oxidation Of Some C2 Compounds (Alcohols, Aldehydes, And Carboxylic Acids) On A Pt/SbAd Electrod, Hong Li, Lincai Jiang, Xiong Jiang

Journal of Electrochemistry

The electrocatalytic oxidation behavior of some C₂ compounds(alcohols, aldehydes and carboxylic acids) on a Pt/Sb_ad electrode prepared in-situ or ex-situ UPD was investigated using pontential sweep and rotating disc electrode methods. It is confirmed that Pt/Sb_ad electrode show the most electrocatalytical active to the oxidation of aldehyde functional group and only a little activity to the oxidation of hydroxyl group, but no activity for the oxidation of carboxyl group.

The experimental results show that the activity of the Pt/Sb_ad electrode prepared by ex-situ UPD is higher than that prepared by in-situ UPD.

The limitations of the …

Oxygen Charge Transfer Reaction At The Pt/Ysz Interface, Yi Jiang, Wenzhao Li, Jingwang Yan, Shizhong Wang

Journal of Electrochemistry

Oxygen Charge transfer reaction has been investigated by various degrees of potential polarization at the Pt/YSZ interface. Anodic and cathodic charge transfer coefficients were found to be unity over the wide range of oxygen partial pressures and temperatures. While the exchange current density of the interface was found dependent on the partial pressure of oxygen in accordance with the relation: i₀=2FKr(K_O2P_O2)^1/4(1+K_O2P_O2)^1/2. Several important parameters, such as electrochemical rate constant, equilibrium constant of oxygen adsorption on Pt surface had also been extracted.

Studies Of Surface Treatment Methods And Their Operating Mechanisms For Activation Of Hydrogen Storage Electrode, Ronghui Hu, Hanxi Yang, Shigang Lu, Shengxian Li, Jingcheng Liu, Chongzhi Yang

Journal of Electrochemistry

Surface treatment methods by use of charge discharge cycling, KBH₄ reduction and KOH etching were parallely investigated for the rapid activation of Mn(NiCoMnAl)₅ electrode. It is found that the MH electrode treated with hot and concentrated KOH solution exhibits rapid and full activation, and also gives lower discharge overvoltage, higher stable capacity and improved cycleability. It is also revealed from SEM, EDAX and ICP analysis that the KOH activation of the electrode proceeds mainly through the enrichment of mischmetal and nickel in surface to form electrocatalytically active surface for hydrogen absorption reaction, but the surface modification with KBH …

Electrocatalytic Reduction Of Nitrite In The Presence Of Complex Of Cobalt(Ⅱ) And 1,10 Phenanthroline, Jian Tong, Xiaojun Dang, Hulin Li

Journal of Electrochemistry

The electrochemistry of cobalt(Ⅱ)-1,10-phenanthroline Co(Phen)₂²⁺ complex and its ability to electrocatalyze the reduction of nitrite were studied, we found that this complex could act as a catalyst in alkaline or neutral solution for nitrite reduction. We have investigated the effect of the complex composition on electrocatalytic ability. The effects of pH value, complex concentration, regeneration and activation of electrocatalyst on the catalytic current have been studied and discussed.

The Electroless Nickel For Aluminium Honeycomb Shielded Vent Windows, Ronghua Wang, Jiaqian Bu

Journal of Electrochemistry

This report summarizes the electroless plating process of magnetic nickel and noncrystalline nickel for aluminium honeycomb shielded vent windows. The test results showed that the electroless nickel plating is bright in appearance, even in thickness, excellent in adhesion with aluminium substrate, good in conductivity, magnetism and corrosion resistance. Shielding efficiency obtained was 67～78 dB under 4 GHz～12 GHz frequency. Environmental reliability tests were made for 56 days under two environmental conditions, that is at 85 ℃ and 35 ℃, 95% relative humidity. The EMI shielding technical requirements of the electroless double nickel plating for aluminium honeycomb shielded vent windows of …

Effect Of Halide Ions On The Deposition Of Electroless Nickel, Keping Han, Jingli Fang

Journal of Electrochemistry

The effect of halide ions on the polarization curves and stationary potential of electroless nickel plating process were studied with electrochemical methods. The acceleration and stabilization mechanism of electroless nickel deposition by halide ions also has been discussed.

Application Of Taguchi Method To Phosphate Coating, Zidong Wei, Hetong Guo

Journal of Electrochemistry

The problems encountered in phosphating such as unstability of phosphating bath, too much sludge in phosphating and the poor microcosmic formation of phosphating films have been solved by improving the phosphating bath composition and phosphating procedures. As far as the non linear relationship between the coating weight and geometric area of coating in the phosphating of the steel is concerned, the Taguchi Method is used to optimize the phosphating process. The linear relationship between the coating weight and geometric area of coating is finally obtained. The operational property of the present phosphating bath is also dramatically improved by the adoption …

Study On Electrode Constructure And Electrical Performance Of Na/S Cell, Jianhua Yang, Jiadi Cao

Journal of Electrochemistry

A sodium wick for sodium electrode and trough shaped performs for sulfur electrode in Na/S cell were designed and investigated. The experiments suggested that the sodium wick for sodium electrode not only improved the discharge performance of cell but also reduced the quantity of sodium utilization, and increased the specific energy of Na/S cell. The trough shaped preform with alumina fibres for sulfur electrode decreased the polarization, improved the charge acceptance and prolonged the life of cell.

The Reduction Of Oxygen To Hydrogen Peroxide In An Acidic Trickle Bed Cell Using Graphite Chip Cathode, Zhaoe Lu, Guanyong Zhang, Tiangeng Zhong, Guonu Fang

Journal of Electrochemistry

The authors investigated the electrochemical reduction of oxygen to hydrogen peroxide in 0.05 mol/L H₂SO₄ solution by the trickle bed electrode using graphite chip. The bed dimension was 14×5×0.6 cm. The current efficiency and the concentration of H₂O₂ in the catholyte were determined at various current strengths and various rates of adding the electrolyte. The proper current was 0.15 A. i.e. the current density was 2.1 mA/cm² vertical cross section area of the bed. The concentration of H₂O₂ reached 7×10^-3 mol/L with the current efficiency of 0.2. If the …

Auger Resonant Raman Spectroscopy Used To Study The Angular Distributions Of The Xe 4d5/2 → 6p Decay Spectrum, B. Langer, N. Berrah, A. Farhat, Oliver Hemmers, J. Bozek

Environmental Studies Faculty Publications

The Auger resonant Raman effect can be used as a method to eliminate natural lifetime broadening in resonant Auger spectra. We have coupled this method with high-resolution photons from the Advanced Light Source to study angular distributions and decay rates of the Xe4d_5/2→6p resonant Auger lines. The angular distribution parameters β of almost all possible final ionic 5p⁴(³P, ¹D, ¹S)6p states have been determined. Our data, which remove the discrepancy between previous lower-resolution experimental results, are compared to different theoretical results.