Open Access. Powered by Scholars. Published by Universities.®

Physical Chemistry Commons™

Open Access. Powered by Scholars. Published by Universities.®

Journal of Electrochemistry

Articles 1771 - 1800 of 2389

Full-Text Articles in Physical Chemistry

Electrochemical Response Of Deformed Marine Steel In Sea-Mud Containing Sulfate Reducing Bacteria, Yan-Liang Huang Aug 2003

Electrochemical Response Of Deformed Marine Steel In Sea-Mud Containing Sulfate Reducing Bacteria, Yan-Liang Huang

Journal of Electrochemistry

The corrosion failure behavior of marine steel is affected by stress,which exists in offshore structures at sea-mud region. In order to conduct the study of stress on the electrochemical response of a selected steel, a kind of natural sea-mud containing sulfate reducing bacteria (SRB) was collected. The electrochemical response of cyclic stress of the specimen with and without cracks in sea-mud was analyzed.

Go to article

Severe Corrosivity And Its Eletrochemical Mechanism Of Seawater In Xiamen Sea Area To Al-Mg Alloys, Le-Yun Lin, Yue-Hong Zhao Aug 2003

Severe Corrosivity And Its Eletrochemical Mechanism Of Seawater In Xiamen Sea Area To Al-Mg Alloys, Le-Yun Lin, Yue-Hong Zhao

Journal of Electrochemistry

The surface layer seawater of different sea areas in China exhibit different corrosivity to Al-Mg alloys according to the experiment results of 16 years exposure in seawater. The seawater in Xiamen sea area possesses severe corrosivity while seawater in Qingdao possesses the mildest corrosivity to Al-Mg alloys with better regularity of corrosion behavior. The present paper illustrates by experiment data that the strongest corrosivity of Xiamen seawater to Al-Mg alloys is owing to the low salinity of the seawater and the “electrolyte effect” come from it. The 16 year corrosion data and corrosion morphology of the typical Al-Mg alloys from …

Go to article

Discussion On Factors Of Unstable 304 Stainless Steel Stress Corrosion Cracking, Xin-Sheng Zhang, Chun-Chun Xu, Gang Hu Aug 2003

Discussion On Factors Of Unstable 304 Stainless Steel Stress Corrosion Cracking, Xin-Sheng Zhang, Chun-Chun Xu, Gang Hu

Journal of Electrochemistry

The 304 stainless steels were stretched at low temperatures to get different martensite phase transformation. Ferrmagnetometer was used to measure the martensite phase content. It was found that the dislocation density of 304 stainless sted was increased unavoidably with increase of deformation. Transmission electron microscope (TEM) was used to study the distribution of the dislocation. The influence of microstructure change on SCC of 304 stainless steel was discussed by slow strain rate testing (SSRT) in 42% MgCl2 boiling solution,metallurgical microscope and scanning electron microscope (SEM).The results showed that martensite phase and dislocation flaw act together on the SCC susceptibility …

Go to article

The Electroless Plating Ni-Fe-P Alloy And Its Voltammetric Behavior, Sen-Lin Wang, Hui-Huang Wu Aug 2003

The Electroless Plating Ni-Fe-P Alloy And Its Voltammetric Behavior, Sen-Lin Wang, Hui-Huang Wu

Journal of Electrochemistry

Electroless Ni-Fe-P alloy deposition from an alkaline bath, containing sodium hypophosphite as reducer, boric acid as buffer agent and sodium citrate as complexing agent, was investigated. To increase the plating rate and to inprove the bath stability, the deposition parameters were optimized. The effects of process parameters (pH, temperature and mole ratio of [Fe2+]/([Ni2+]+[Fe2+]) on the plating rate and deposit composition were examined and it was found that the presence of ferrous sulfate in the bath has an inhibitory effect on the alloy deposition. As a consequence, the percentage of iron in the electroless …

Go to article

The Mechanism Of Electrocatalytic Reduction Of Oxygen On Manganese Dioxide, Yu-Liang Cao, Han-Xi Yang, Xin-Ping Ai, Li-Fen Xiao Aug 2003

The Mechanism Of Electrocatalytic Reduction Of Oxygen On Manganese Dioxide, Yu-Liang Cao, Han-Xi Yang, Xin-Ping Ai, Li-Fen Xiao

Journal of Electrochemistry

The oxygen electroreduction on the MnO2 electrode was investigated by analysis of the polarzation properties of oxygen reduciton and its dependence on MnO2 discharge state, in combination with the characterization of discharge intermediate and the kinetic parameters of the oxygen reduction. Based on the experimental observation and mechanistic analysis, it was suggested that the reduction of oxygen was closely related to the discharge behaviors of MnO2. When MnO2 was electrochimically reduced to MnOOH, it was immediately oxidized by oxygen molecules. Thus the oxygen reduction proceeds through continuous oxidation of the discharge product of MnO2 …

Go to article

Study Of Electrolyzed Pure Iron And Rrr-H Method, Wei-Min Cao, Ren-He Yin, Hui-Gen Yan, Yi-Bing Zhang, Ying-Chun Dai Aug 2003

Study Of Electrolyzed Pure Iron And Rrr-H Method, Wei-Min Cao, Ren-He Yin, Hui-Gen Yan, Yi-Bing Zhang, Ying-Chun Dai

Journal of Electrochemistry

The high purity electrolytic iron was made from scrap iron chips. The purity of electrolyzed pure iron was above 99.98% by chemical analysis. The resistivity was measured at 298 K and at 4.2 K under an applied longitudinal-magnetic field of 8000 e. The ratio of resistivity at 298 K to that at 4.2 K, The value of residual resistivity ratio (RRR H) roughly depended on the purity of iron. Pure iron electrolyzed on Ti substrate had very compact texture as evident by SEM.

Go to article

Study Of Marine Biocorrosion Using Afm And Molecular Techniques, Herbert H.P.Fang, Lichong Xu, Tong Zhang May 2003

Study Of Marine Biocorrosion Using Afm And Molecular Techniques, Herbert H.P.Fang, Lichong Xu, Tong Zhang

Journal of Electrochemistry

Biofilm is ubiquitous in nature.However,corrosin caused by biofilm is still by and large overlooked. This presentation is to demonstrate the applications of several newly developed analytical techniques in chemisrty and microbiology for the study of marine biocorrosion on steel. AFM(atomic force microscopy) was applied to investigate the initial formation mechanism of biofilm and the degree of corrosion of steel in polluted seawater. DNA/RNA-related molecular techniques were used to analyze the microbial composition corrosive biofilm. Results showed that microbial corrosion began within six days, and the corroded volume in the increased as a power function of time with an index 2.83. …

Go to article

A Bilayer Self-Assembled Membrane Electrode For Fluorescence And Its Electrochemical Characterization, Xiang-Ying Sun, Bin Liu, Yun-Bao Jiang May 2003

A Bilayer Self-Assembled Membrane Electrode For Fluorescence And Its Electrochemical Characterization, Xiang-Ying Sun, Bin Liu, Yun-Bao Jiang

Journal of Electrochemistry

The bilayer membrane was assemblied on Au electrode by the electrostatic interaction between the fluorescence regent 1-naphthylamine diacetate acid (NADA) and DL-Cysteine. The SAMs electrode NADA/Cys/Au can be used as fluorescence and electrochemical sensor for metal ions. This paper states the electrochemical characterization of NADA/Cys/Au and SAMs' application in continous determination for Cu2+ and Ni2+.

Go to article

The Electrochemical Behaviors Of A Novel Ferrocene Alkylthiol Sams On Au Electrode, Xiao-Gang Zhang, Yan-Li Shi, Hu-Lin Li May 2003

The Electrochemical Behaviors Of A Novel Ferrocene Alkylthiol Sams On Au Electrode, Xiao-Gang Zhang, Yan-Li Shi, Hu-Lin Li

Journal of Electrochemistry

A novel alkylthiol molecule containing ferrocene and pyridium moieties and its hydrogenated products were synthesized and subsequently assembled on Au electrode as SAMs. Cyclic voltammogram(CV) was used to investigate the structure-dependent electrochemical response of the SAMs in 0.1 mol/L HClO4 aqueous solution.

Go to article

Initial Stages Of Pd Deposition Onto Au(111) Electrodes From Pdso4, Jing Tang, Petri M., Kibler L.A., Kolb D.M. May 2003

Initial Stages Of Pd Deposition Onto Au(111) Electrodes From Pdso4, Jing Tang, Petri M., Kibler L.A., Kolb D.M.

Journal of Electrochemistry

Metal thin films have attracted considerable interest in relation to catalysis, energy, material, corrosion and environmental protection. Pd thin film is capable of proton reduction and strong hydrogen absorption, which has shown electrocatalytic activity to the oxidation of small organic molecules. In this paper, in-situ STM measurements are performed to study the deposition process and the influence of the surface structure and anion adsorption. When Pd is deposited from PdSO4 solution on Au(111) in the UPD range, a monolayer of Pd with pseudomorphic (1×1) structure was formed on the substrate with induced (3×7) R19° SO42- adsorption. With …

Go to article

Recent Progress In The Research On Electrodeposition Of Composite Coatings, Xiao-Bing Liu, Xu-Cheng Wang, Yu Chen, Dan-Hong Cheng, Zu-Zhan Yu May 2003

Recent Progress In The Research On Electrodeposition Of Composite Coatings, Xiao-Bing Liu, Xu-Cheng Wang, Yu Chen, Dan-Hong Cheng, Zu-Zhan Yu

Journal of Electrochemistry

Recent progress in the research on composite coatings prepared by electroplating technology is reviewed. The nanoscaled particles, electrocatalytic, photoactive composite coatings are emphatically discussed. The composite coatings prepared by dispersing nanoscaled particles could attain better hardness, wear resistance and corrosion resistance than those of composite coatings which prepared by adding micronscaled particles. As compared with pure metal electrode and alloy electrode, some electrocatalytic composite coatings electrode could markedly reduce the overvoltages of cathodic and anodic electrode reaction. In recent years, the electrocatalytic composite coatings which based on metal oxides and conductive polymer as matrix materials become a newest field of …

Go to article

Preparation And Electrochemical Preformance Of Zn-La Alloys, Xian-Ling Meng, Hua-Bin Yang, En-Dong Yang, Xiao-Dan Wang, Hai-Chang Zhang, Jun-Hong Wang, Zuo-Xiang Zhou May 2003

Preparation And Electrochemical Preformance Of Zn-La Alloys, Xian-Ling Meng, Hua-Bin Yang, En-Dong Yang, Xiao-Dan Wang, Hai-Chang Zhang, Jun-Hong Wang, Zuo-Xiang Zhou

Journal of Electrochemistry

Zn-La alloys were prepared by solid phase diffusion method and the effects of La on the electrochemical performance of zinc electrodes were investigated using potentiostatic polarization technique and charging/discharging cycle test. The results showed that adding La to zinc electrode remarkably suppressed the zinc dendrite, the shape of zinc electrode and zinc corrosion, and hence, markedly improved the cycle performance of zinc electrodes. The discharging capacity of the zinc electrode containing 0.5at.% La which was the optimum was still 520 mAh/g after it cycled 80s at the current of 100 mA. The XPS showed that La element mainly adhered on …

Go to article

Microstructure And Electrochemical Characteristics Of The Anodic Film Formed On Aluminum Surface, Jeng-Kuei Chang, Chi-Min Liao, Chih-Hsiung Chen, Wen-Ta Tsai May 2003

Microstructure And Electrochemical Characteristics Of The Anodic Film Formed On Aluminum Surface, Jeng-Kuei Chang, Chi-Min Liao, Chih-Hsiung Chen, Wen-Ta Tsai

Journal of Electrochemistry

The thickness, morphology, chemical composition, and crystallinity of the anodized film formed on aluminum were examined in a transmission electron microscope (TEM). Thin foil for TEM analysis was prepared by ultramicrotomy. The relationship between the microstructure and the electrochemical characteristics of the alumina film forming on the pure aluminum was discussed in this investigation. At the forming voltage less than 100V, the anodized films formed at 85 ℃in aqueous ammonium adipate electrolyte was amorphous in nature. Although the film resistance was increased with the forming voltage, its dielectric constant was not changed significantly. As the forming voltage exceeded 100V, crystalline …

Go to article

Oxidation Behavior Of Zr-Cu-Al-Ni Amorphous Alloys In Air At 300～500℃, H. H. Hsieh, W. Kai, T. G. Neih, Y. Kawamura May 2003

Oxidation Behavior Of Zr-Cu-Al-Ni Amorphous Alloys In Air At 300～500℃, H. H. Hsieh, W. Kai, T. G. Neih, Y. Kawamura

Journal of Electrochemistry

The oxidation behavior of the Zr- based bulk amorphous alloy (BMG; Zr-30Cu-10Al-5Ni in at.%) was studied in dry air over the temperature range 300～500 ℃. The kinetic results indicated that the amorphous alloy oxidized linearly at 300 ℃, while the parabolic oxidation was observed at 350～425 ℃, and the oxidation behavior at 500 ℃ was irregular and complicated. In general, the scales formed on the surface of the amorphous alloy were temperature-dependent, consisting of tetragonal-ZrO2 at 300 ℃, and of mostly tetragonal-ZrO2 as well as minor amounts of monoclinic-ZrO2 and CuO at T ≥ 350 ℃.

Go to article

Cavitation Erosion Behavior Of Ni-Al Intermetallic Coatings, J-T Chang, H-C Yeh, J-L He, K-C Chen May 2003

Cavitation Erosion Behavior Of Ni-Al Intermetallic Coatings, J-T Chang, H-C Yeh, J-L He, K-C Chen

Journal of Electrochemistry

A cathodic arc plasma ion plating process was demonstrated to deposlt deposit Ni-Al film on AISI 1045 carbon steel to evaluate the cavitation protection. Three target materials with Ni52Al48, Ni60Al4o, and Ni70Al30 compositions were used to reveal the microstructural of coatings. Experimental results show that the nickel content in these deposits increased with the nickel contenof the target material. The major phase of deposited film was NigAl regardless of the target materials. All of the as- deposited films presented very strong adhesion and reflects their cavitation erosion behavior in …

Go to article

Selective Corrosion In Duplex Stainless Steel, Wen-Ta Tsai, Kuen-Ming Tsai, Chang-Jian Lin, Yan Fu May 2003

Selective Corrosion In Duplex Stainless Steel, Wen-Ta Tsai, Kuen-Ming Tsai, Chang-Jian Lin, Yan Fu

Journal of Electrochemistry

In duplex stainless steel, the two constituent phases, namely ferritic (α) and austenitic (γ) phases, have different crystal structure and chemical composition. They may thus exhibit different corrosion resistances in aqueous environment. In this investigation, an electrochemical technique with spatial resolution was employed to measure the potential difference between these two constituent phases in 2205 duplex stainless steel. Image analyzing techniques were also used to examine the preferential corrosion between α and γ phases. The experimental results showed that ferrite had a higher potential than austenite in 0.01 mol/L NaCl solution. In 2 mol/L H2SO4+x mol/L …

Go to article

Electrochemical Monitoring On The Deactivation Of A Metallic Oxide Anode, Li-Kun Xu, Shi-Zhe Song, Ting-Yong Wang, Guang-Zhang Chen May 2003

Electrochemical Monitoring On The Deactivation Of A Metallic Oxide Anode, Li-Kun Xu, Shi-Zhe Song, Ting-Yong Wang, Guang-Zhang Chen

Journal of Electrochemistry

The process of accelerated life test of an IrO2/Ta2O5 coated titanium anode was monitored using cyclic voltammetry and electrochemical impedance spectroscopy. The vatiation with electrolysis time of anodic voltammetric charge Q*, the double layer capacitance Cdl,the oxide film resistance Rf and the charge transfer resistance Rct for oxygen evolution was measured. A deactivation mechanism was proposed based on the observation results.

Go to article

Metastable Pitting Of Aluminum Anodic Film In Neutral Sodium Chloride Solution, Jing-Mao Zhao, Zhi-Jun Bai, Yu Zuo May 2003

Metastable Pitting Of Aluminum Anodic Film In Neutral Sodium Chloride Solution, Jing-Mao Zhao, Zhi-Jun Bai, Yu Zuo

Journal of Electrochemistry

Potentiodynamic polarization,electrochemical noise and SEM were used to study the corrosion behavior of L2 aluminum anodic film in 1 mol/L NaCl solutions. The results showed that anodic oxidization of aluminum increases its corrosion resistance greatly. However metastable pits were also observed when the film was thin or was exposed to the solutions for a long time. These pits with a diameter less than 10μm often occurred around the metallic inclusions in film.

Go to article

Corrosion Behavior Of Reinforcing Steel In Concrete Subjected To Chloride Contamination By Eis, Rong-Gang Hu, Rong-Gui Du, Chang-Jian Lin May 2003

Corrosion Behavior Of Reinforcing Steel In Concrete Subjected To Chloride Contamination By Eis, Rong-Gang Hu, Rong-Gui Du, Chang-Jian Lin

Journal of Electrochemistry

Electrochemical impedance spectroscopy(EIS) was employed to study the influence of chloride on the corrosion behavior of reinforcing steel in concrete. In Nyquist plot, the spectrum consists of two semicircles, indicating that the reinforced concrete system contained two time constants,one derived from electrical double layer of reinforcing steel and the other from the deposition film of concrete layer. The depressed semicircle in lower frequency featured the non-faradic behavior of the electrical double layer (EDL) deviated from idea capacitor due to diffusive effect which was attributed to the surface roughness of rebar and the inhomogenity of concrete layer. Then the EDL was …

Go to article

Corrosion Behavior Of Mg1.85Mm0.15Ni Hydrogen Storage Alloy Modified By Electroless Cu In Ch3Ohâ·H2O Solutions, Hua-Bin Yang, Hai-Chang Zhang, Hua Sun, Xiao-Dan Wang, Zuo-Xiang Zhou May 2003

Corrosion Behavior Of Mg1.85Mm0.15Ni Hydrogen Storage Alloy Modified By Electroless Cu In Ch3Ohâ·H2O Solutions, Hua-Bin Yang, Hai-Chang Zhang, Hua Sun, Xiao-Dan Wang, Zuo-Xiang Zhou

Journal of Electrochemistry

The corrosion behavior of the Mg1.85Mm0.15Ni (Mm:Ce-rich mischmetal) alloy modified by electroless Cu coating in different CH3OH-H2O solutions has been investigated by potentiodynamic polarization and electrochemical impedance spectroscopy. These results showed that the corrosion behavior was improved after electroless Cu. The potentiodynamic polarization and electrochemical impedance spectroscopy results showed that the alloy electrode had more promising anti-corrosion behavior after coated in a 40%CH3OH-H2O solution. The values of corrosion current density and electrode reaction resistance were 5.6 mA·cm-2 (11.7 mA·cm-2 for uncoated alloy electrode) and 22.25 Ω·cm …

Go to article

Synthesis And Electrochemical Characteristics Of Nickel-Based Complex Oxide LiANi0.78Co0.2Cd0.02O2, Rong-Zhong Yuan, Mei-Zhen Qu, Zuo-Long Yu May 2003

Synthesis And Electrochemical Characteristics Of Nickel-Based Complex Oxide LiANi0.78Co0.2Cd0.02O2, Rong-Zhong Yuan, Mei-Zhen Qu, Zuo-Long Yu

Journal of Electrochemistry

The nickel-based complex oxide LiaNi0.78Co0.02O2 cathode materials for lithium-ion rechargeable batteries was synthesized by the improved solid-state reaction method with LiOH·H2O, ball-like Cd-doped Ni(OH)2 and Co2O3 as raw materials. The analysis ICP-AES proved that the as-prepared compounds were near the stoichiometric form. The XRD, SEM and electrochemical characteristics testing were also carried out. The results showed that the complex cathode material LiaNi0.78Co0.2Cd0.02O2 has layered structure, homogeneous surface distributions,uniform particles with good crystal morphology as well as stable electrochemical …

Go to article

Perfluorinated Sulfonic Acid Lithium Conductivity Humidity Sensor, Hong-Feng Xu, Jing Liu, Li Wan May 2003

Perfluorinated Sulfonic Acid Lithium Conductivity Humidity Sensor, Hong-Feng Xu, Jing Liu, Li Wan

Journal of Electrochemistry

Treat carbon paper with 3% PTFE solution and dried in 340 ℃ for 40 minutes to enhance its intension, and level off the surface of the carbon paper with a mixture of XC-72 carbon black and PTFE solution. With those treated carbon paper as electrodes, recast Nafion thin film from 5% Nafion solution as humidity sensitive material, a solid polymer electrolyte humidity sensor was prepared on a thin PET film. Take the relative humidity data from several saturated salt solutions, the relationship between conductivity response and relative humidity was studied at different relative humidies .The results showed: when the polymer …

Go to article

Conductance Properties For Electrolyte Of Lithium Ion Battery At Low Temperature, Jing-Li Han, Yan-Mei Yu, Jian Chen, Chun-Tong Wang May 2003

Conductance Properties For Electrolyte Of Lithium Ion Battery At Low Temperature, Jing-Li Han, Yan-Mei Yu, Jian Chen, Chun-Tong Wang

Journal of Electrochemistry

The system of LiPF6-ethylene carbonate (EC)-methy1 acetate (MA) was studied. The conductivities of this system were measured under various composition and various salt concentrations at temperature range of 20～-50 ℃. The optimum composition of this system was selected. The tests of cyclic voltammography and charge-discharge were carried out. This system was compared with commercial electrolyte solution.

Go to article

Corrosion Prediction Of Carbon Steel In Concentrated Lithium Bromide Solutions At High Temperature Using Bp Neural Network, Nai-Bao Huang, Cheng-Hao Liang May 2003

Corrosion Prediction Of Carbon Steel In Concentrated Lithium Bromide Solutions At High Temperature Using Bp Neural Network, Nai-Bao Huang, Cheng-Hao Liang

Journal of Electrochemistry

Neutral network model has been developed for the computation of corrosion rate of carbon steel in LiBr solutions.The results indicate that the model is capable of reproducing the effects of changes in alkalinity, temperatures, LiBr and Na2MoO4 concentrations on the rates of general corrsion and good agreement between calculated and experimental corrosion rate is obtained. The model can be used to satisfactorily predict the corrosion rate of carbon steel in different concentrations of LiBr solutions containing different inhibitors at different temperatures. It also provides a novel method for corrosion monitoring of metals used in LiBr absorption chiller.

Go to article

Effect Of Scn- On The Transition Current Of Zn During The Electrodeposition Zn-Co Alloys, Ren-He Yin, Wei-Min Cao, Zheng-Hua Fang May 2003

Effect Of Scn- On The Transition Current Of Zn During The Electrodeposition Zn-Co Alloys, Ren-He Yin, Wei-Min Cao, Zheng-Hua Fang

Journal of Electrochemistry

For co-deposition of Zn-Co alloys at sufphate baths with micro-concentration of SCN- the transition current of Zn was found with the deposition process changing from normal Co-deposition to anomalous co-deposition, and the value of transition current increased with increasing SCN- concentration, but decreased with increasing value of pH. The existence of SCN- decreases the evolution overpotential of Co metal, but has no effects on the evolution overpotential of Zn metal and H2.

Go to article

In Situ Measurements Of Solution Conductivity In Microwave Field, Yong-Qing Su, Chun-Peng Liu Feb 2003

In Situ Measurements Of Solution Conductivity In Microwave Field, Yong-Qing Su, Chun-Peng Liu

Journal of Electrochemistry

The curves of the conductivity as a function of temperature for 24 kinds of solutions have been in situ measured both in the microwave field and in absence of microwave field. The results indicated that the relationship between the conductivity in microwave field (Lw) and temperature (T) can be expressed by an equation Lw=a′+b′T+c′T2 , similar to the one that is valid in absence of the microwave field Ln=a+bT+cT2. Conductivity in the absence and presence of microwave field can be linked by the equation lnLw=A+BLn+CL2n …

Go to article

Magnetic Resonance Studies On Lithium Intercalation Into Carbons, Xiao-Rong Zhou, Zhen-Ming Du, Lin Zhuang, Jun-Tao Lu Feb 2003

Magnetic Resonance Studies On Lithium Intercalation Into Carbons, Xiao-Rong Zhou, Zhen-Ming Du, Lin Zhuang, Jun-Tao Lu

Journal of Electrochemistry

The electron spin resonance(ESR) and 7Li-NMR magnetic resonance (7Li-NMR) studies on lithium intercalation into carbons were reviewed based on recently published papers, including those by the authors of this review. Two kinds of electronic spins were found in ESR studies. One corresponds to the charge carrier electrons and is called the Pauli spin. From the ESR intensity of Pauli spins, the curve of the density of electronic states can be deduced for the carbon material studied and, in turn, the contribution of the band model mechanism to the lithium intercalation can be calculated for the given carbon sample. The other …

Go to article

The Electrochemical Performance Studies On Novel Lifepo4 Cathode Materials For Li-Ion Batteries, Zhi-Cong Shi, Chen Li, Yong Yang Feb 2003

The Electrochemical Performance Studies On Novel Lifepo4 Cathode Materials For Li-Ion Batteries, Zhi-Cong Shi, Chen Li, Yong Yang

Journal of Electrochemistry

The cathode materials of LiFePO4 and  LiFePO4 coated with carbon were synthesized by means of solid state reaction and ballmilling. The samples were characterized by X-ray diffraction, scanning electron microscopy, gas-phase element analysis and titration analysis methods. Electrochemical tests of two kinds of materials showed that both of them exhibit a 3.4V discharge voltage plateau, however, the coated samples demonstrated the improved performance in terms of discharge capacity and cyclic stability.

Go to article

The Study On The Synthesis And Electrochemical Property Of K2Feo4, Yong-Long Wang, Ning Zhou, Shi-Hai Ye, Xue-Ping Gao, Feng Wu, Zuo-Xiang Zhou, De-Ying Song Feb 2003

The Study On The Synthesis And Electrochemical Property Of K2Feo4, Yong-Long Wang, Ning Zhou, Shi-Hai Ye, Xue-Ping Gao, Feng Wu, Zuo-Xiang Zhou, De-Ying Song

Journal of Electrochemistry

The synthesis,characterization and electrochemical property of K2FeO4 for positive materal of lithium ion battery were studied. K2FeO4 with low purity was gained through the reaction of KCIO and Fe(NO3)3 in KOH solution and after recrystalization the purity of K2FeO4 reached 97%～98%. The methods of XRD and FTIR were used to measure the structure of K2FeO4 and its initial discharge performance was tested.

Go to article

Study Of Electrochemical Lithium Intercalation Performance Of Ni0.67Mg0.33O, Zhen-Cai Huang, Mao-Hui Chen, Guo-Tao Wu, Jin-Kua You, Zu-Geng Lin Feb 2003

Study Of Electrochemical Lithium Intercalation Performance Of Ni0.67Mg0.33O, Zhen-Cai Huang, Mao-Hui Chen, Guo-Tao Wu, Jin-Kua You, Zu-Geng Lin

Journal of Electrochemistry

In the present work, Ni0.67Mg0.33O and NiO were produced by sol-gel method, and characterized by XRD, a rietveld refinement and the discharge/charge test.It was found that the magnesium-doping restrained the reduction of Ni and decreased the reversible capacity for the sample of Ni0.67Mg0.33O. But the formation of the solid solution after the magnesium-doping facilitated the high dispersion of NiO, and accordingly improved the electrochemical performance.

Go to article

First Prev Next Last