Physical Chemistry Commons^™

Fabrication Of Mnox/Mwcnts-Gc Nanocatalyst For Oxygen Evolution Reaction, Yaser M. Asal Mr, Islam M. Al-Akraa Dr, Amr M. Arafa Eng.

Chemical Engineering

Manganese oxide (MnOx) and multiwalled carbon nanotubes (MWCNTs) are intended to modify the GC electrode for oxygen evolution reaction (OER). Optimization of MnOx loading is carried out and the deposition of 55 cycles was sufficient to obtain the highest activity toward OER. The stability of the catalyst is enhanced by the addition of MWCNTs. As a result, an amount of 22 kWh/Kg of O₂ of energy is saved. Several techniques including cyclic voltammetry, linear sweep voltammetry, chronoamperometry, chronopotentiometry, field-emission scanning electron microscopy, and energy dispersive X-ray spectroscopy will be combined to track the catalyst activity and to determine its …

Thermosetting Polymers Via Azide Alkyne Cycloaddition, Richard H. Cooke Iii

Dissertations

This dissertation exploits properties inherent to azide-alkyne cycloaddition and applies practical solutions to difficult problems. Chapter II addresses structure-property relationships in glassy azido-alkyne matrices by varying the identity of the central linkage within tetrapropargyl bis-aniline-type crosslinkers, and by the addition or omission of Cu(I) catalyst. This systematic study showed that an ether or methylene linkage yielded lower melting tetrapropargyl crosslinkers that were soluble in, and produced homogeneous, networks when cured with, a standard azido resin, di(3-azido-2-hydroxypropyl) ether of bisphenol-A; in contrast, a sulfone linkage yielded a relatively insoluble crosslinker and poorly dispersed, heterogeneous networks when reacted with the same …

Recent Progress For Fe-N-C Electrocatalysts In Alkaline Fuel Cells, Xin Deng, Heng-Quan Chen, Ye Hu, Qing-Gang He

Journal of Electrochemistry

Fuel cells are highly recommended nowadays due to their intrinsic advantages such as high energy conversion efficiency, nearly no pollution, and convenient operation. With the development of anion exchange membrane, alkaline fuel cells have gone through a renaissance thanks to their superiorities such as faster reaction kinetics, wider choices for both fuels and electrocatalysts. It is essential to find an appropriate electrocatalyst for oxygen reduction reaction (ORR) to improve the performance of alkaline fuel cells. Further commercialization of the widely used Pt-based materials has suffered from disadvantages such as scarcity and high cost. As alternatives to largely investigated Pt-based materials, …

A Study Of Pulse Electrodeposition On Suppressing The Formation Of Lithium Dendrite, Wen-Jun Guo, Zi-Qiong Li, Ruo-Hao Ke, Dong-Fang Niu, Heng Xu, Xin-Sheng Zhang

Journal of Electrochemistry

A pulse charge method was used to suppress the formation of lithium dendrite on the copper electrode in 0.5 mol·L^-1 LiBr/propylene carbonate (PC) electrolyte. The surface variation of lithium deposition was investigated by scanning electron microscope and impedance measurement. The SEM test showed that the lithium dendrites were formed on the copper electrode during the traditional process of electrodeposition. However, the formed dendrite was suppressed by pulse charge method. The results of the impedance measurement confirmed that the pulse electrodeposition could suppress the dendrite under the optimized duty ratio (0.5). The long single pulse deposition time decreased the resistance …

Pt/G-C3N4 Nanosheet For Visible Light-Induced Enhancement Of The Activity For Formic Acid Electro-Oxidation, Yong-Rong Sun, Chun-Yu Du, Guo-Kang Han, Ya-Jing Wang, Yun-Zhi Gao, Ge-Ping Yin

Journal of Electrochemistry

By using graphitic carbon nitride nanosheet (g-C₃N₄ nanosheet) as a support,Pt/g-C₃N₄ nanosheet catalyst was fabricated by microwave assisted polylol process. The nanoparticles size,composition,structure and optical properties of Pt/g-C₃N₄ nanosheet were characterized by TEM,XRD,XPS and UV-Vis diffuse reflectance spectroscopy. Comparing with the catalytic activities toward formic acid electro-oxidation under dark and visible light illumination,the superior activity of Pt/g-C₃N₄ nanosheet catalyst was achieved under visible light illumination. This visible light-driven enhancement in the formic acid performance could be attributed to the plasmon-induced electron-hole separation on g-C₃N₄ with …

Carbon Composite Fe3O4 Nanoparticles Based Electrochemical Sensor For Hydrogen Peroxide Detection, Si-Yu Zhang, Hui-Juan Wang, Shu-Fang Li, Jian-Ying Qu

Journal of Electrochemistry

In this work, a novel hydrogen peroxide electrochemical sensor was constructed with ferroferric oxide (Fe₃O₄) magnetic nanoparticles, which demonstrated good electrocatalytic activity for hydrogen peroxide. There existed a good linear relationship between the concentration of hydrogen peroxide and the oxidation peak current in the range of 1.00 × 10^-6 ~ 1.00 × 10^-3 mol·L^-1 (R = 0.9980) with the detection limit of 6.60 × 10-7 mol·L^-1. The sensor exhibited good anti-interference ability, high reproducibility and stability.

Simulation Of Fractal Growth On Metal Wire Electrode, Li-Feng Ding, Pei-Yuan Mao, Jun Cheng, Yu-Lan Niu, Yu-Hao Wen, Wei Chen

Journal of Electrochemistry

During processes of metal electrodepostion, there exist many complex morphological forms such as dendritic growing in the cathode deposited metal edge, which will seriously affect the quality of the electrodeposited product and current efficiency during machining. Investigations on dendritic crystal growing process and morphology could help controlling growth of electrolysis precipitate. In this work, Python and Matlab softwares were used, and the model of parallel electrode electrodeposition was established based on the diffusion-limited aggregation (DLA) model. By analyzing the law of fractal growth at different conditions of the particles number, probability, electrode spacing, the movement step length and orientation drift, …

Lead Modified Nanoporous Platinum Electro-Catalysts For Formic Acid Oxidation, Yuan-Yuan Zhang, Qing-Feng Yi, Ge-Kun-Kun Zuo, Tao Zou, Xiao-Ping Liu, Xiu-Lin Zhou

Journal of Electrochemistry

Platinum (Pt) catalysts modified by other suitable metals significantly enhance their electrochemical activities for formic acid oxidation. In this work, a titanium-supported nanoporous network platinum (nanoPt/Ti) electrode was prepared using a hydrothermal method. The as-prepared nanoPt/Ti electrode was modified with a certain amount of lead by using cyclic voltammetry for different scan cycle numbers (n), namely, n = 10, 15, 20 and 30, to synthesize the novel lead-modified nanoporous Pt (nanoPb_(n)-Pt/Ti) electrodes. Electro-oxidation of formic acid on these electrodes was studied with cyclic voltammetry (CV), chronoamperometry and chronopotentiometry in sulfuric acid solution. CV curves showed that both nanoPt/Ti …

Chemical Stability Investigations Of Catalyst Layer In Pemfc, Yan-Yan Gao, Ming Hou, Yong-Yi Jiang, Dong Liang, Jun Ai, Li-Min Zheng

Journal of Electrochemistry

This work was intended to study the effect of free radicals on the chemical stability of catalyst layer via ex situ accelerated stress test (AST). Fenton reagent was used as the free radical provider in this research. Apart from the decomposition of Nafion in catalyst layer, the agglomerated Pt nanoparticles and the corroded carbon support were also observed after being treated in Fenton reagent for 100 h. Firstly, the existence of fluoride (F) ions evidenced the chemical decomposation of Nafion after being attacked by trace radical species, which was supported by the intensity decrease in the C-F stretching and vibration …

Co3(Hcoo)6@Rgo As A Promising Anode For Lithium Ion Batteries, Heng Jiang, Jing-Min Fan, Ming-Sen Zheng, Quan-Feng Dong

Journal of Electrochemistry

Metal–organic framework(MOF) is a kind of novel electrode materials for lithium ion batteries. Here, a composite material Co₃(HCOO)₆@rGO was synthesized for the first time by in situ loading of Co₃(HCOO)₆ on rGO (reduced oxide graphene) through a solution chemistry method. As an anode material for lithium ion batteries, it exhibited an excellent cycle stability as well as a large reversible capacity of 926 mAh·g^-1 at a current density of 500 mA·g^-1 after 100 cycles within the voltage range of 0.02 ~ 3.0 V vs. Li/Li⁺ with a good rate capability. …

Preparations And Electrochemical Performances Of Carbon Coated Silicon/Graphite Composites, Tian-Yi Gao, Zheng-Liang Gong

Journal of Electrochemistry

In this work, the carbon coated silicon (Si@C) composite materials were synthesized based on the industrial silicon powder (600 meshes) via a high energy ball milling combing with in-situ carbon coating (carbonization) method. The Si@C/graphite (Si/C) composite anode materials were prepared by a simple mechanical ball-milling approach. The effects of carbon coating and the ratio of Si to graphite on electrochemical performances of Si/graphite composite materials were investigated systematically. Compared with the nano-Si/graphite composites, the Si/C composites showed higher reversible capacity, better rate capability and cycle performance. The Si@C materials composited of amorphous carbon and crystal silicon with the primary …

Preparation And Electrochemical Performance Of Ag-Tio2-Mno2 Composites, Ling-Xiao Zhang, Hui-Hui Zhao, Li-Juan Zhang, Yu Fu

Journal of Electrochemistry

The silver-titanium dioxide  co-modified manganese dioxide (Ag-TiO₂-MnO₂) cathode material was prepared through high temperature solid state reaction. The microstructure, phase composition and electrochemical performance of the prepared samples were characterized by X-ray diffraction spectroscopy (XRD), scanning electron microscopy (SEM), Fourier transform infrared spectrometry (FT-IR), X-ray photoelectron spectroscopy (XPS), Energy-dispersive X-ray spectroscopy (EDS), Cyclic voltammetry (CV), galvanostatic discharge and electrochemical impedance spectroscopy (EIS). Results showed that the unmodified and Ag-TiO₂ modified MnO₂ samples both exhibited β-MnO₂ structurebut with different morphologies. The EDS mapping results revealed that Ag was uniformly dispersed on the surface of …

Nanocomposites Of Polypyrrole And Cobalt Oxide As Efficient And Stable Multifunctional Materials For Supercapacitors And Overall Water Splitting, Ahlam Alghamdi

Electronic Theses & Dissertations

NANOCOMPOSITES OF POLYPYRROLE AND COBALT OXIDE AS EFFICIENT AND STABLE MULTIFUNCTIONAL MATERIALS FOR SUPERCAPACITORS AND OVERALL WATER SPLITTING

An Abstract of the Thesis by

Ahlam Alghamdi

The main objective of this study is to synthesize nanostructured cobalt oxide decorated on polypyrrole using a facile method for energy applications. For this, polypyrrole was first synthesized using a chemical polymerization method. In the second step, a varying amount of cobalt oxide was decorated on polypyrrole using a hydrothermal process. The synthesized materials were structurally and electrochemically characterized. It was observed that the electrochemical properties of the composites depend on their composition. The …

Photoelectrochemical Studies On Non-Noble Metal Based Catalysts Towards Tandem Solar Water Splitting, Arun Siddarth Sridhar

Dissertations

Photoelectrochemical (PEC) water splitting makes direct use of solar energy incident on semiconductor photoelectrodes, and it is a convenient, economic option to produce high purity hydrogen at low temperatures. The use of multiple light absorbers can increase overall solar energy utilization and provide a solution to the trade-off between overall band gap and band edge positioning of photoelectrodes specific to solar water oxidation and water reduction. The study of non-noble metal based catalysts for hydrogen evolution reaction (HER) and oxygen evolution reactions (OER) are essential for economic practical commercialization of photo-electrolyzers. This dissertation focuses on the use of a variety …

A Label-Free Immunosensor Based On K3[Fe(Cn)6] And Aldehyde-Functionalized Pyridinium, Xia Hu, You-Ming Shen, Guang-Yu Shen

Journal of Electrochemistry

A novel aldehyde-functionalized pyridinium was successfully synthesized. Using K₃[Fe(CN)₆] as a redox species modified on the surface of the electrode through Poly(diallyldimethylammonium chloride), we developed a label-free immunosensor based on aldehyde-functionalized pyridinium that was applied to simplify antibody immobilization on the electrode surface, in which no additional chemical cross-linking was required. In addition, the introduction of K₃[Fe(CN)₆] on the surface of electrode avoided the use of other redox species in the electrolyte solution. Under the optimal experimental conditions, differential pulse voltammetry (DPV) signals corresponding to different α-Fetoprotein (AFP) concentrations were measured. After …

One-Step Co-Deposition Of Zsm-5/Pani/Pss Electroactive Film And Its Kinetics Characteristics Of Electrochemical Control Selective Separation For Pb2+ Ions, Wen-Lei Qiao, Xiao Du, Feng-Feng Gao, Jun-Lan Zheng, Sha-Sha Li, Xiao-Gang Hao

Journal of Electrochemistry

A novel electroactive composite film consisting of ZSM-5/polyaniline/polystyrene sulfonate(ZSM-5/PANI/PSS) was prepared by double pulse one step co-deposition method. The ZSM-5/PANI/PSS composite film was characterized by FT-IR, SEM, XRD, and XPS techniques. The highly crystalline nano-ZSM-5 was synthesized by hydrothermal method, which could be evenly dispersed in aqueous solution by ultrasonic treatment. The synthesis condition of composite film was optimized through changing the pH value of solution. The ZSM-5/PANI/PSS composite film showed higher adsorption capacity for Pb²⁺ ions. Langmuir model was applied to analyze the adsorption process. The adsorption capacity of composite film for Pb²⁺ ions was 235 mg·g …

Synthesis And Electrochemical Properties Of Li3V2(Bo3)3/C Anode Materials For Lithium-Ion Batteries, You Wang, Yi-Wen Zeng, Xing Zhong, Xing Liu, Quan Tang

Journal of Electrochemistry

The Li₃V₂(BO₃)₃/C (LVB/C) composite materials were successfully synthesized in two steps:Firstly, a stoichiomertric mixture of Li₂C₂O₄, V₂O₅, H₃BO₃, H₂C₂O₄•H₂O and ethanol was thoroughly ball-milled to get the precursors. Secondly, the precursors were post-calcinated to get the ultimate products. The calcination temperatures of 750 ℃, 800 ℃ and 850 ℃ were selected based on TG-DTA analyses. The crystal structures, surface morphologies and carbon contents of the samples calcinated at five conditions, …

Electrochemical Performance Of Moo2-C Composite Coatings, Quan-Yi Li, Qi Yang, Yan-Hong Zhao

Journal of Electrochemistry

The molybdenum dioxide-carbon(MoO₂-C)composite coatings on the surface of Cu foils were prepared by simple knife coating route and followed by sintering in vacuum. The morphology, composition, structure and electrochemical performance of the MoO₂-C composite coatings were investigated. The results demonstrated that the MoO₂-C composite coatings consist of MoO₂ nano-particles with monoclinic crystal structure and amorphous carbon. Some MoO₂ nano-particles with a size range of 5-30nm were loaded on the surface of carbon matrices; while some MoO₂ nano-particles with a size of ~5nm were encapsulated inside. The composite coatings showed porous structure …

Preparation Of Ni(Dpim)2Cl2 Complex For The Electrocatalytic Reduction Of Co2, Li-Pu Zhang, Dong-Fang Niu, Xin-Sheng Zhang

Journal of Electrochemistry

A new Ni(dpim)₂Cl₂complex using 2-(diphenylphosphino)-1-methylimidazole (dpim) as ligand was prepared and served as a catalyst for the electrochemical reduction of CO₂. The electrochemical redox behavior of Ni(dpim)₂Cl₂ in CH₃CN/TPABF₄ solution under nitrogen atmosphere showed the two-electron irreversible reduction at -0.7 V and one-electron quasi-reversible reduction at -1.3 V. After bubbling CO₂ into the electrolyte, the reduction peak appeared at -1.3 V became irreversible and the peak current increased from 0.48 mA·cm^-2 to 0.55 mA·cm^-2. Moreover, the peak current at -1.3 V could further increase …

Preparation Of Co3O4/Ti Electrocatalytic Membrane Electrode For Catalytic Oxidation Of Benzyl Alcohol, Yu-Mei Zheng, Zhen Yin, Hong Wang, Jian-Xin Li

Journal of Electrochemistry

The cobalt oxide(Co₃O₄) nanoparticles were loaded on microporous Ti membrane to prepare Co₃O₄/Ti electrocatalytic membrane electrode by dip-coating method. The microstructures and electrochemical properties of Co₃O₄/Ti electrocatalytic membrane were investigated. The Co₃O₄/Ti electrocatalytic membrane reactor (ECMR) assembled by using the Co₃O₄/Ti electrocatalytic membrane as an anode was adopted for catalytic oxidation of benzyl alcohol to produce benzaldehyde and benzoic acid.The effects of different operation parameters on benzyl alcohol conversion, and selectivity to benzaldehyde and benzoic acid of ECMR were studied. …

Electrochemical Oxidation Of P-Chlorophenol On Porous Ti/Bdd Electrode Cooperated With Cathode Dechlorination, Rong-Ling Chen, Wei-Min Huang, Ya-Peng He, Jun Shi, Hai-Bo Lin

Journal of Electrochemistry

The electrochemical oxidation of p-chlorophenol on porous Ti/BDD electrode cooperated with synergistic effect of cathode dechlorination was studied. Electrochemical degradation tests of p-chlorophenol were conducted in single and double compartment electrolytic cells separately, and the results showed that the mineralization happened mainly in the anode region. The product of chloride ions produced from the cathodic reduction of 4-chlorophenol in the single cell migrated to the anode region and further generated active chlorine toward electro-catalytic oxidation. At the same time, the chloride ion produced from the cathode of the double cell was difficult to be migrated to the anode region, which …

Preparation And Properties Of Manganese Oxide And Polyaniline-Carbon Composite Electrode, Tian-Tian Zhou, Bing Wu, Chao Deng, Ying Gao

Journal of Electrochemistry

The polyaniline-carbon (PAnC) electrode was prepared by the polymerization of aniline monomer and activated carbon in ice water bath, and followed by chemical deposition of manganese dioxide MnO₂-PAnC composite material. The specific capacitance of MnO₂-PAnC reached 459 F•g^-1. The cyclic voltammetric results showed a small deformation in the voltammogram curve obtained with the MnO₂-PAnC electrode at high scan rate, indicating good reversibility and capacitive properties. The AC impedance results revealed that the MnO₂-PAnC electrode displayed the smallest charge transfer resistance and the fastest diffusion
rate of surface ions than other …

Preparations And Corrosion Protection Investigations Of Diethylene Triamine Penta(Methylene Phosphonic Acid)-Zn2+ Conversion Coatings On Cold Rolled Steel Substrates, Wei He, Ru Yan, Ying-Qi Wang, Xiang Gao, Hou-Yi Ma

Journal of Electrochemistry

Novel diethylene triamine penta(methylene phosphonic acid) (DTPMPA)-zinc ion (Zn²⁺) conversion coatings with uniform blue color and excellent corrosion protection were directly formed on the cold rolled steel (CRS) substrates by immersing a CRS plate into the film-forming solutions containing the appropriate concentrations of DTPMPA and Zn²⁺ ion at the proper pH. In this paper, surface morphologies and elemental compositions of DTPMPA-Zn²⁺ conversion coatings were characterized by SEM and EDS, respectivey. The surface functional groups, chemical constituents and binding modes to the substrates were investigated by means of FTIR and XPS methods. The influences of DTPMPA concentrations …

Simulation Analysis In Dynamic Performance Of Proton Exchange Membrane Fuel Cell Under Starting Condition, Yan Xiao, Ying-Jie Chang, Wei Zhang, Qiu-Hong Jia

Journal of Electrochemistry

Based on the equivalent circuit model, by considering both the dynamic gas pressure model and the dynamic heat transfer model, a lumped parameter model is developed. The start process of the fuel cell is simulated by using SIMULINK software. The undershoot of the voltage is observed from the simulation results, and the response time of the voltage is basically the same as that of the fuel cell temperature, which indicates that the temperature has great influence on the dynamic performance of the fuel cell. From the perspective of the temperature, the dynamic responses of the thermodynamic potential, the activation overvoltage, …

Interaction Between Energy And Electrocatalysis —— A Review On The 1st Young Scientist Forum On Energy Electrocatalysis, Hong Li, Wen-Bin Cai

Journal of Electrochemistry

No abstract provided.

Effects Of Rotating Magnetic Fields On Pem Fuel Cell Performance, Mao-Liang Wu, En-Ze Wang, Guang-De Pan, Zhong-Jun Liu, Fei Xie

Journal of Electrochemistry

Proton Exchange Membrane (PEM) fuel cell performance may be improved by application of additional magnetic fields. In this work, one square permanent magnet, made of either 16 combination cylinder magnets with homopolarity or 16 combination cylinder magnets with heteropolarity, was exerted on the fuel cell surface to produce additional magnetic field affecting PEM fuel cell performance. The influences of magnetic field status (rotating, static and none) on polarization and power density curves measured in a PEM fuel cell were investigated. The results verified the benefit of magnetic field, proving that the magnetic field distribution could improve the fuel cell output. …

From Flasks To Applications: Design And Optimization Of Giant Quantum Dots Using Traditional And Automated Synthetic Methods, Christina J. Hanson

Nanoscience and Microsystems ETDs

Semiconducting nanocrystals, also known as quantum dots (QDs), that emit light with near-unity quantum yield and are extremely photostable are attractive options as down-conversion and direct electricity-to-light materials for a variety of applications including solid-state lighting, display technologies, bio-imaging and optical tracking. Standard QDs with a core/thin shell structure display fluorescence intermittency (blinking) and photobleaching when exposed to prolonged room temperature excitation for single dot measurements, as well as significant reabsorption and energy transfer when densely packed into polymers or at high solution concentrations.

We have developed thick shell “giant” QDs (gQDs), ultra-stable photon sources both at the ensemble and …

Preparation And Characterization Of Titanate-Phosphate Passivation Film On Tinplate, Zi-Yu Wang, Ming-Hao Wang, De-Yu Li, Ning Li

Journal of Electrochemistry

A passivation film was prepared on tinplate surface with a composite passivating agent made of titanate and phosphate. The surface morphologies, chemical compositions and corrosion resistances of the passivation films were characterized by scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), salt spray test, Tafel polarization measurement and electrochemical impedance spectroscopy (EIS). The results were compared with those films untreated and treated with titanate or phosphate passivation. It was shown that the titanate and phosphate passivation film was mainly composed of Ti₃(PO₄)₄·nH₂O and TiO₂. The finely crystallized surface could seal …

Preparation And Properties Of Nanocrystalline Nickel By Pulse Electrodeposition On Glassy Carbon, Ya-Li Zhang, Ming-Xian Zhang, Teng-Da Guo, Yan-Jie Zhao, Sheng-Xue Yu

Journal of Electrochemistry

Nanocrystalline nickel exhibits electrocatalytic activity for methanol. In this work, nanocrystalline nickel coating has been obtained by using the double pulse method on glassy carbon materials surface. The influence of pulse conditions on the grain size of nanocrystalline nicke was studied. The concentrations and compositions of the plating bath were  300 g·L^-1 NiSO₄·6H₂O,45 g·L^-1 NiCl₂·6H₂O,40 g·L^-1 H₃BO₃,5 g·L^-1 C₇H₅NO₃S,and 0.05 g·L^-1 C₁₂H₂₅NaO₄S. The optimal pulse process parameters including the average pulse …

Synthesis And Electrochemical Properties Of Nickel-Rich Cathode Material Lini0.6Co0.2Mn0.2O2 With High Initial Coulombic Efficiency, Xiao-Yun Guan, Chao-Yu Hong, Jian-Ping Zhu, Wei-Li Wang, Yi-Xiao Li, Yong Yang

Journal of Electrochemistry

Nickel-rich cathode materials LiNi_0.6Co_0.2Mn_0.2O₂(NCM622)were synthesized by a co-precipitation-solid state sintering method at different temperatures. The structure, morphology and electrochemical performance of the as-prepared materials were investigated by X-ray powder diffraction (XRD) /Rietveld refinement, scanning electron microscope (SEM) and electrochemical experiments. It is found that NCM622 calcined at 800 ℃ showed the lowest degree of cation disorder (~1.97%) with a high initial Coulombic effiency of 92.2% and the capacity retention of 81.4% after 100 cycles.