Open Access. Powered by Scholars. Published by Universities.®

Physical Chemistry Commons™

Open Access. Powered by Scholars. Published by Universities.®

Engineering Science and Materials

Institution
Keyword
Publication Year
Publication
Publication Type

Articles 1351 - 1380 of 1756

Full-Text Articles in Physical Chemistry

Electrochemical Monitoring On The Deactivation Of A Metallic Oxide Anode, Li-Kun Xu, Shi-Zhe Song, Ting-Yong Wang, Guang-Zhang Chen May 2003

Electrochemical Monitoring On The Deactivation Of A Metallic Oxide Anode, Li-Kun Xu, Shi-Zhe Song, Ting-Yong Wang, Guang-Zhang Chen

Journal of Electrochemistry

The process of accelerated life test of an IrO2/Ta2O5 coated titanium anode was monitored using cyclic voltammetry and electrochemical impedance spectroscopy. The vatiation with electrolysis time of anodic voltammetric charge Q*, the double layer capacitance Cdl,the oxide film resistance Rf and the charge transfer resistance Rct for oxygen evolution was measured. A deactivation mechanism was proposed based on the observation results.

Go to article

Corrosion Behavior Of Reinforcing Steel In Concrete Subjected To Chloride Contamination By Eis, Rong-Gang Hu, Rong-Gui Du, Chang-Jian Lin May 2003

Corrosion Behavior Of Reinforcing Steel In Concrete Subjected To Chloride Contamination By Eis, Rong-Gang Hu, Rong-Gui Du, Chang-Jian Lin

Journal of Electrochemistry

Electrochemical impedance spectroscopy(EIS) was employed to study the influence of chloride on the corrosion behavior of reinforcing steel in concrete. In Nyquist plot, the spectrum consists of two semicircles, indicating that the reinforced concrete system contained two time constants,one derived from electrical double layer of reinforcing steel and the other from the deposition film of concrete layer. The depressed semicircle in lower frequency featured the non-faradic behavior of the electrical double layer (EDL) deviated from idea capacitor due to diffusive effect which was attributed to the surface roughness of rebar and the inhomogenity of concrete layer. Then the EDL was …

Go to article

Corrosion Behavior Of Mg1.85Mm0.15Ni Hydrogen Storage Alloy Modified By Electroless Cu In Ch3Ohâ·H2O Solutions, Hua-Bin Yang, Hai-Chang Zhang, Hua Sun, Xiao-Dan Wang, Zuo-Xiang Zhou May 2003

Corrosion Behavior Of Mg1.85Mm0.15Ni Hydrogen Storage Alloy Modified By Electroless Cu In Ch3Ohâ·H2O Solutions, Hua-Bin Yang, Hai-Chang Zhang, Hua Sun, Xiao-Dan Wang, Zuo-Xiang Zhou

Journal of Electrochemistry

The corrosion behavior of the Mg1.85Mm0.15Ni (Mm:Ce-rich mischmetal) alloy modified by electroless Cu coating in different CH3OH-H2O solutions has been investigated by potentiodynamic polarization and electrochemical impedance spectroscopy. These results showed that the corrosion behavior was improved after electroless Cu. The potentiodynamic polarization and electrochemical impedance spectroscopy results showed that the alloy electrode had more promising anti-corrosion behavior after coated in a 40%CH3OH-H2O solution. The values of corrosion current density and electrode reaction resistance were 5.6 mA·cm-2 (11.7 mA·cm-2 for uncoated alloy electrode) and 22.25 Ω·cm …

Go to article

Synthesis And Electrochemical Characteristics Of Nickel-Based Complex Oxide LiANi0.78Co0.2Cd0.02O2, Rong-Zhong Yuan, Mei-Zhen Qu, Zuo-Long Yu May 2003

Synthesis And Electrochemical Characteristics Of Nickel-Based Complex Oxide LiANi0.78Co0.2Cd0.02O2, Rong-Zhong Yuan, Mei-Zhen Qu, Zuo-Long Yu

Journal of Electrochemistry

The nickel-based complex oxide LiaNi0.78Co0.02O2 cathode materials for lithium-ion rechargeable batteries was synthesized by the improved solid-state reaction method with LiOH·H2O, ball-like Cd-doped Ni(OH)2 and Co2O3 as raw materials. The analysis ICP-AES proved that the as-prepared compounds were near the stoichiometric form. The XRD, SEM and electrochemical characteristics testing were also carried out. The results showed that the complex cathode material LiaNi0.78Co0.2Cd0.02O2 has layered structure, homogeneous surface distributions,uniform particles with good crystal morphology as well as stable electrochemical …

Go to article

Perfluorinated Sulfonic Acid Lithium Conductivity Humidity Sensor, Hong-Feng Xu, Jing Liu, Li Wan May 2003

Perfluorinated Sulfonic Acid Lithium Conductivity Humidity Sensor, Hong-Feng Xu, Jing Liu, Li Wan

Journal of Electrochemistry

Treat carbon paper with 3% PTFE solution and dried in 340 ℃ for 40 minutes to enhance its intension, and level off the surface of the carbon paper with a mixture of XC-72 carbon black and PTFE solution. With those treated carbon paper as electrodes, recast Nafion thin film from 5% Nafion solution as humidity sensitive material, a solid polymer electrolyte humidity sensor was prepared on a thin PET film. Take the relative humidity data from several saturated salt solutions, the relationship between conductivity response and relative humidity was studied at different relative humidies .The results showed: when the polymer …

Go to article

Conductance Properties For Electrolyte Of Lithium Ion Battery At Low Temperature, Jing-Li Han, Yan-Mei Yu, Jian Chen, Chun-Tong Wang May 2003

Conductance Properties For Electrolyte Of Lithium Ion Battery At Low Temperature, Jing-Li Han, Yan-Mei Yu, Jian Chen, Chun-Tong Wang

Journal of Electrochemistry

The system of LiPF6-ethylene carbonate (EC)-methy1 acetate (MA) was studied. The conductivities of this system were measured under various composition and various salt concentrations at temperature range of 20～-50 ℃. The optimum composition of this system was selected. The tests of cyclic voltammography and charge-discharge were carried out. This system was compared with commercial electrolyte solution.

Go to article

Corrosion Prediction Of Carbon Steel In Concentrated Lithium Bromide Solutions At High Temperature Using Bp Neural Network, Nai-Bao Huang, Cheng-Hao Liang May 2003

Corrosion Prediction Of Carbon Steel In Concentrated Lithium Bromide Solutions At High Temperature Using Bp Neural Network, Nai-Bao Huang, Cheng-Hao Liang

Journal of Electrochemistry

Neutral network model has been developed for the computation of corrosion rate of carbon steel in LiBr solutions.The results indicate that the model is capable of reproducing the effects of changes in alkalinity, temperatures, LiBr and Na2MoO4 concentrations on the rates of general corrsion and good agreement between calculated and experimental corrosion rate is obtained. The model can be used to satisfactorily predict the corrosion rate of carbon steel in different concentrations of LiBr solutions containing different inhibitors at different temperatures. It also provides a novel method for corrosion monitoring of metals used in LiBr absorption chiller.

Go to article

Effect Of Scn- On The Transition Current Of Zn During The Electrodeposition Zn-Co Alloys, Ren-He Yin, Wei-Min Cao, Zheng-Hua Fang May 2003

Effect Of Scn- On The Transition Current Of Zn During The Electrodeposition Zn-Co Alloys, Ren-He Yin, Wei-Min Cao, Zheng-Hua Fang

Journal of Electrochemistry

For co-deposition of Zn-Co alloys at sufphate baths with micro-concentration of SCN- the transition current of Zn was found with the deposition process changing from normal Co-deposition to anomalous co-deposition, and the value of transition current increased with increasing SCN- concentration, but decreased with increasing value of pH. The existence of SCN- decreases the evolution overpotential of Co metal, but has no effects on the evolution overpotential of Zn metal and H2.

Go to article

Magnetic Resonance Studies On Lithium Intercalation Into Carbons, Xiao-Rong Zhou, Zhen-Ming Du, Lin Zhuang, Jun-Tao Lu Feb 2003

Magnetic Resonance Studies On Lithium Intercalation Into Carbons, Xiao-Rong Zhou, Zhen-Ming Du, Lin Zhuang, Jun-Tao Lu

Journal of Electrochemistry

The electron spin resonance(ESR) and 7Li-NMR magnetic resonance (7Li-NMR) studies on lithium intercalation into carbons were reviewed based on recently published papers, including those by the authors of this review. Two kinds of electronic spins were found in ESR studies. One corresponds to the charge carrier electrons and is called the Pauli spin. From the ESR intensity of Pauli spins, the curve of the density of electronic states can be deduced for the carbon material studied and, in turn, the contribution of the band model mechanism to the lithium intercalation can be calculated for the given carbon sample. The other …

Go to article

The Electrochemical Performance Studies On Novel Lifepo4 Cathode Materials For Li-Ion Batteries, Zhi-Cong Shi, Chen Li, Yong Yang Feb 2003

The Electrochemical Performance Studies On Novel Lifepo4 Cathode Materials For Li-Ion Batteries, Zhi-Cong Shi, Chen Li, Yong Yang

Journal of Electrochemistry

The cathode materials of LiFePO4 and  LiFePO4 coated with carbon were synthesized by means of solid state reaction and ballmilling. The samples were characterized by X-ray diffraction, scanning electron microscopy, gas-phase element analysis and titration analysis methods. Electrochemical tests of two kinds of materials showed that both of them exhibit a 3.4V discharge voltage plateau, however, the coated samples demonstrated the improved performance in terms of discharge capacity and cyclic stability.

Go to article

The Study On The Synthesis And Electrochemical Property Of K2Feo4, Yong-Long Wang, Ning Zhou, Shi-Hai Ye, Xue-Ping Gao, Feng Wu, Zuo-Xiang Zhou, De-Ying Song Feb 2003

The Study On The Synthesis And Electrochemical Property Of K2Feo4, Yong-Long Wang, Ning Zhou, Shi-Hai Ye, Xue-Ping Gao, Feng Wu, Zuo-Xiang Zhou, De-Ying Song

Journal of Electrochemistry

The synthesis,characterization and electrochemical property of K2FeO4 for positive materal of lithium ion battery were studied. K2FeO4 with low purity was gained through the reaction of KCIO and Fe(NO3)3 in KOH solution and after recrystalization the purity of K2FeO4 reached 97%～98%. The methods of XRD and FTIR were used to measure the structure of K2FeO4 and its initial discharge performance was tested.

Go to article

Study Of Electrochemical Lithium Intercalation Performance Of Ni0.67Mg0.33O, Zhen-Cai Huang, Mao-Hui Chen, Guo-Tao Wu, Jin-Kua You, Zu-Geng Lin Feb 2003

Study Of Electrochemical Lithium Intercalation Performance Of Ni0.67Mg0.33O, Zhen-Cai Huang, Mao-Hui Chen, Guo-Tao Wu, Jin-Kua You, Zu-Geng Lin

Journal of Electrochemistry

In the present work, Ni0.67Mg0.33O and NiO were produced by sol-gel method, and characterized by XRD, a rietveld refinement and the discharge/charge test.It was found that the magnesium-doping restrained the reduction of Ni and decreased the reversible capacity for the sample of Ni0.67Mg0.33O. But the formation of the solid solution after the magnesium-doping facilitated the high dispersion of NiO, and accordingly improved the electrochemical performance.

Go to article

Application Of Biphenyl Electroploymerization For Overcharge Protection In Li-Ion Batteries, Li-Fen Xiao, Xin-Ping Ai, Yu-Liang Cao, Han-Xi Yang Feb 2003

Application Of Biphenyl Electroploymerization For Overcharge Protection In Li-Ion Batteries, Li-Fen Xiao, Xin-Ping Ai, Yu-Liang Cao, Han-Xi Yang

Journal of Electrochemistry

The electropolymerization of biphenyl at overcharged positive electrode was investigated for overcharge protection of Li-ion batteries. Biphenyl in electrolyte as an additive can electrochemically polymerize at 4.5～4.75 V(vs. Li/Li+) to form a layer of conductive film on cathode surface. The surface film increases the internal resistance and the gases released during the electropolymerization also increases the internal pressure of the batteries, which therefore enhance the sensitivities of the electrical disconnecting devices. During prolonged overcharge, the growth of the conductive polymer film can create short circuit between the positive and negative electrodes and cause self-discharge of the batteries to …

Go to article

The Preparation And Characterization Of Zno-Pani Composite Film, Yan-Yan Xi, Huai-Guo Huang, Zhi-Xin Zheng, Ping Dong, Jian-Zhang Zhou, Ling-Ling Wu, Zhong-Hua Lin Feb 2003

The Preparation And Characterization Of Zno-Pani Composite Film, Yan-Yan Xi, Huai-Guo Huang, Zhi-Xin Zheng, Ping Dong, Jian-Zhang Zhou, Ling-Ling Wu, Zhong-Hua Lin

Journal of Electrochemistry

ZnO nanoparticle films were prepared on the Au film, PANI film and ITO by sol-gel method, and their morphological optical and photoelectrochemical properties were also studied. The results showed that the porous structure of PANI can suppress the aggregation of ZnO particles, resulting in the blue shift of on-set in the UV-Vis spectra and fluorescence spectra of ZnO-PANI composite film compared with that of ZnO-Au film. It was suggested that the ZnO-PANI composite film can be used in photoelectric coversion.

Go to article

The Electrochemical Behavior Of Amorphous Ni-P And Ni-B Alloys In 0.5 Mol/L H2So4, Xu-Cheng Wang, Wei-Jiang Wang, Hou-Tian Liu, Zu-Zhan Yu Feb 2003

The Electrochemical Behavior Of Amorphous Ni-P And Ni-B Alloys In 0.5 Mol/L H2So4, Xu-Cheng Wang, Wei-Jiang Wang, Hou-Tian Liu, Zu-Zhan Yu

Journal of Electrochemistry

Polarization curves and impedance spectra were used to investigate the electrochemical behavior of amorphous Ni-P and Ni-B alloys in 0.5 mol/L H2SO4 solutions. The possible reason about the remarkable difference in the electrochemical behavior between amorphous Ni-P and Ni-B alloys was discussed.

Go to article

An Eqcm Study Of Water Adsorption And Oxidation On Pt Electrodes In Sulfate Acid Sulotions, Heng Lin, Sheng-Pei Chen, Jin-Mei Lin, Ai-Lan Lin, Guo-Liang Chen Feb 2003

An Eqcm Study Of Water Adsorption And Oxidation On Pt Electrodes In Sulfate Acid Sulotions, Heng Lin, Sheng-Pei Chen, Jin-Mei Lin, Ai-Lan Lin, Guo-Liang Chen

Journal of Electrochemistry

Simultaneous frequency and current responses during potential cycling of Pt electrode were measured in 0.1 mol·L-1 H2SO4 solution by using EQCM. Quantitative analysis of the mass change revealed that the increase of mass in the hydrogen and double-layer regions in a positive-going potential scan was due to water adsorption on the Pt electrode, further calculation indicated that water molecules adsorbed on Pt electrode in the double-layer regions through a low discharge quomodo .The EQCM studies provided quantitative results of surface mass variation during water adsorption and oxidation,and have thrown new light in elucidating the structure of …

Go to article

Behaviors Of Fe-Cr Alloys During Cavitation Damage, Xia Bai, Dong-Bai Sun, Hong-Ying Yu, Hui-Ming Meng, Hui-Qin Li, Zi-Shuang Fan Feb 2003

Behaviors Of Fe-Cr Alloys During Cavitation Damage, Xia Bai, Dong-Bai Sun, Hong-Ying Yu, Hui-Ming Meng, Hui-Qin Li, Zi-Shuang Fan

Journal of Electrochemistry

The influence of the surface galvanic effect on the behaviors of three Fe-Cr alloys during cavitation damage in NaCl solutions have been investigated. The results showed that the galvanic effect caused by the inhomogeneity between the undamaged surface of the alloy and the damaged one will be enhanced by the area ratio of the undamaged and the damaged. The behaviors of alloys during cavitation are closely related to both their mechanical performance and anti-corrosion capabilities.

Go to article

Study On The Corrosion & Electrochemical Properties Of Alloy Aa5083 And The Effect Of Active Chlorine In Seawater, Hong-Ren Wang, Jian-Hua Wu, Jun-Tao Wang, Hong-Bin Wang, Zhi-Gang Fang Feb 2003

Study On The Corrosion & Electrochemical Properties Of Alloy Aa5083 And The Effect Of Active Chlorine In Seawater, Hong-Ren Wang, Jian-Hua Wu, Jun-Tao Wang, Hong-Bin Wang, Zhi-Gang Fang

Journal of Electrochemistry

In this paper potentiodynamic technique, cyclic polarization technique and immersion corrosion method were used to study the corrosion and electrochemical properties of AA5083 alloy in quiescent seawater, the effect of active chlorine on its properties was also studied. The results obtained indicate that the active chlorine has no remarkable impact on the corrosion and electrochemical properties of AA5083 alloy in area of design concentration which range from 0.2 to 0.5 mg/L, and it has favorable influence on the improvement of pitting corrosion resistance. While the pH value of seawater has evident influence on the corrosion resistance of AA5083 alloy.

Go to article

Study For The Cathodic Behavior Of Active Chlorine On 316l Ss Electrode Surface, Hui Yu, Ming-Xian Sun, Yan Ma, Xiao-Bin Wang Feb 2003

Study For The Cathodic Behavior Of Active Chlorine On 316l Ss Electrode Surface, Hui Yu, Ming-Xian Sun, Yan Ma, Xiao-Bin Wang

Journal of Electrochemistry

The cathodic reducing reactions of active chlorine on 316 L SS electrode surface have been investigated by electrochemical techniques. The open circuit potential shifted positively and the limited diffusion current density increased significantly with the increasing content of active chlorine in the 3.5% sodium chloride solution. The two cathodic reduction processes of HClO and ClO- exhibited on the surface of electrode with the active chlorine added to the 3.5%sodium chloride solution and the corresponding potentials of the two reducing reactions were confirmed. The linear relationship of the mass transport-limited Faradaic current, Id vs. the square root of the angular …

Go to article

Development And Study Of The (Ag)-Ni/Cr Composite Plating With Antibacterial Properties And Corrosion Resistance, Ya-Ping Zhao, Jin-Hua Wang, Ren-He Yin, Jin Zheng, Le-Shu Yu Feb 2003

Development And Study Of The (Ag)-Ni/Cr Composite Plating With Antibacterial Properties And Corrosion Resistance, Ya-Ping Zhao, Jin-Hua Wang, Ren-He Yin, Jin Zheng, Le-Shu Yu

Journal of Electrochemistry

The 3-factor and 3-level orthogonal experiment was designed and through the comparison of the different films' antibacterial properties measured by bacterial colony counting and the corrosion resistance studied with the AC impedance method. The optimal plating conditions of the (Ag)-Ni/Cr composite plating, a novel functional plating, were determined. The results have indicated that the (Ag)-Ni/Cr composite plating is characterized by both antibacterial and corrosion resisting properties and has its wide applied prospect.

Go to article

Synthesis By Complexation Processes And Characterization Of Lini0.8Co0.2O2 Cathode Materials, Jing Liu, Zhao-Yin Wen, Zhong-Hua Gu, Xiu-Jian Zhu, Zu-Xiang Lin Feb 2003

Synthesis By Complexation Processes And Characterization Of Lini0.8Co0.2O2 Cathode Materials, Jing Liu, Zhao-Yin Wen, Zhong-Hua Gu, Xiu-Jian Zhu, Zu-Xiang Lin

Journal of Electrochemistry

The layered LiNi0.8Co0.2O2 compound, which has been of great interest for lithium ion batteries, was prepared at low temperatures by calcining a complex precursor at different temperatures. The physical properties of the synthesized cathode materials were discussed in the light of structural (XRD). The charge and discharge cycling of the cells containing the synthesized oxide as the positive electrode in conjunction with lithium metals and employing a non-aqueous electrolyte showed that LiNi0.8Co0.2O2 treated at 900 ℃ exhibited excellent performances. The first discharge capacity of LLiNi0.8Co0.2O2 …

Go to article

Fabrication Of SncuX/Cms Composite Materials For Lithium-Ion Batteries, Yu Liu, Jing-Ying Xie, Jun Yang, Ke Wang, Bao-Feng Wang Feb 2003

Fabrication Of SncuX/Cms Composite Materials For Lithium-Ion Batteries, Yu Liu, Jing-Ying Xie, Jun Yang, Ke Wang, Bao-Feng Wang

Journal of Electrochemistry

The composite material were prepared by sub-ctrochemical cycling tests showed that coulombic efficiency of the electrodes prepared by the composite materials was near 100 % after second cycle and the capacity dropped less than 5% after the 30th cycle, versus 390 mAh⋅g-1 special capacity, improving 26% special capacity of pure CMS electrode. The electrochemical performance of the composite materials is depended strongly on the alloy content in the composite, the addhesive strength between alloy particles and CMS matrix, the distribution of particles on the surface of CMS and the particle size of alloy. The composite material can be applied …

Go to article

Pure Iron Electrolyzed From Scrap Iron Chips And Its Corrosion Characteristics, Wei-Min Cao, Ren-He Yin, Hui-Ceng Yan, Zhi-Qiang Ye Feb 2003

Pure Iron Electrolyzed From Scrap Iron Chips And Its Corrosion Characteristics, Wei-Min Cao, Ren-He Yin, Hui-Ceng Yan, Zhi-Qiang Ye

Journal of Electrochemistry

The high purity electrolytic iron was made from scrap iron chips. Electrolytic conditions of pure iron were determined in chloride baths and the highest purity was 99.983% by chemical analysis. Pure iron had very compact texture and high mechanical strength by SEM figures of cross section. In deaerated 0.5 kmol·m-3 H2SO4 and 0.5 kmol·m-3 NaCl solutions, the corrosion rate of iron decreased with increasing purity.

Go to article

Electroreduction Of Cd(Ⅱ) In Dmso And Complexation Of Cd(Ⅱ) With Coumarin Derivates, Ji-Guo Song, Hua-Can Song, Qi-Qin Yang, Yi-Wen Chen, Zun-Le Xu Feb 2003

Electroreduction Of Cd(Ⅱ) In Dmso And Complexation Of Cd(Ⅱ) With Coumarin Derivates, Ji-Guo Song, Hua-Can Song, Qi-Qin Yang, Yi-Wen Chen, Zun-Le Xu

Journal of Electrochemistry

Cadmium p-toluenesulfonate was synthesized and tested electrochemically for the first time. This salt can lose all the hydrated water easily and the dehydrated salt do not deliquesce in the air.Hence,the cadmium p-toluenesulfonate is suitable for the electrochemical studies in organic solvents.When the Cd(Ⅱ) reduced on Pt electrode in Cd(p-CH3C6H4SO3)2+TBAP+DMSO, underpotential deposition of cadmium occurred at first, and then cadmium deposited. 4-Methyl-7-hydroxylcoumarin and 3-aminocoumarin coordinate with Cd(Ⅱ) respectively, as a result the reductive potentials of Cd(Ⅱ) moved to the negative direction.

Go to article

Lithium Intercalation Performance Of P-Doped Phenolic Resin Pyrolysis Carbon, Bao-Hua Li, Kai-Xi Li, Yonggen Lv, Chun-Xiang Lv, Dong Wu, Li-Cheng Ling Nov 2002

Lithium Intercalation Performance Of P-Doped Phenolic Resin Pyrolysis Carbon, Bao-Hua Li, Kai-Xi Li, Yonggen Lv, Chun-Xiang Lv, Dong Wu, Li-Cheng Ling

Journal of Electrochemistry

Phosphorus-doped phenolic resin carbon was prepared by low temperature (700 ℃) pyrolysis of thermoplastic phenolic resin containing different amounts of phosphorus pentoxide after curing. X-ray diffraction pattern and the constang-current charge-discharge properties of phenolic resin carbon were studied. The results showed that the phenolic resin carbon microstructure became out of order with increasing of content phosphorus pentoxide, otherwise, the first discharge reversible capacities increased firstly and then decreased. The first discharge reversible capacity of phenolic resin carbon containing 9wt% phosphorus pentoxide was 528 mA·h·g-1 which was higher than that of non-phosphorus doped phenolic resin carbon(230 mA·h·g-1) did.

Go to article

Studies On The Inhibition Of Yki-05 Corrosion Inhibitor To 907a Steel In Different Immersed Environments, Hui Yu, Jian-Hua Wu, Hong-Ren Wang, Jian-Hua Qian, Guang-Zhang Chen Nov 2002

Studies On The Inhibition Of Yki-05 Corrosion Inhibitor To 907a Steel In Different Immersed Environments, Hui Yu, Jian-Hua Wu, Hong-Ren Wang, Jian-Hua Qian, Guang-Zhang Chen

Journal of Electrochemistry

The inhibition of YKI-05 Corrosion inhibitor in different conditions was studied using potentiodynamic polarization technique. The resuled shown that (i) the inhibitor film layer was formed stably on the surface of 907A steel electrode when it was persistently immersed in static seawater and the inhibition efficiency reached 90% or so. The inhibition mechanism is negative catalytic effect. (ii) the inhibitior film layer was not stable when the electrode was periodically immersed in seawater and was destroyed more significantly with the increase of electrode exposing time. The film was only a covered layer on the surface of electrode and it retarded …

Go to article

Steady State Simulation Of Ysz Intermediate-Temperature Fuel Cell, Zi-Jing Lin, Ye Gu, Xiao-Hua Zhang Nov 2002

Steady State Simulation Of Ysz Intermediate-Temperature Fuel Cell, Zi-Jing Lin, Ye Gu, Xiao-Hua Zhang

Journal of Electrochemistry

With a coupled 2D electrochemical and thermal modeling software, the characteristics of the steady state operation of the intermediate-temperature fuel cell with thin yttria-stabilized zirconia(YSZ) electrolyte was analyzed. The parameters of I-V equation were obtained from fitting the experiment results and the choice of grid points was determined by balancing the accuracy requirement and computational efficiency. The temperature fields at different operation circumstances such as flow designs, material choices for interconnect, were examined. The dependences of the output power and cell efficiency on the operating voltage at different temperatures were studied. Based upon the analysis of the temperature profile, it …

Go to article

Preparation And Performance Of Lifeo2 Coated Nickel Oxide Cathode For Molten Carbonate Fuel Cells, Chun-Ming Wang, Fei Li, Ke-Ao Hu Nov 2002

Preparation And Performance Of Lifeo2 Coated Nickel Oxide Cathode For Molten Carbonate Fuel Cells, Chun-Ming Wang, Fei Li, Ke-Ao Hu

Journal of Electrochemistry

A novel cathode for molten carbonate fuel cells was prepared by coating LiFeO2 over the surface of porous NiO cathode by a simple combustion process. The analytical results of X-ray diffraction (XRD), energy dispersive analysis of X-ray (EDAX), scanning electron microscopy (SEM) and transmission electron microscopy (TEM) indicated that the LiFeO2 coating on the surface of NiO particles consisted of nonometer-sized LiFeO2 grains and sintered tightly with the NiO particles. The LiFeO2 coating dramatically reduced the contacting area of NiO with the carbonate melts, thus the solubility of NiO in the carbonate melts was decreased. Meanwhile, …

Go to article

Review Of Mathematical Model For Proton Exchange Membrane Fuel Cell, Shan-Hai Ge, Bao-Lian Yi, Hua-Min Zhang Nov 2002

Review Of Mathematical Model For Proton Exchange Membrane Fuel Cell, Shan-Hai Ge, Bao-Lian Yi, Hua-Min Zhang

Journal of Electrochemistry

In the review with 49 references, the mathematical models for proton exchange membrane fuel cell (PEMFC) were summarized. The mechanistic model and empirical model were introduced. Transfer in the membrane, catalyst layer, diffusion layer and flow field of PEMFC were described. The importance of water and heat management was analyzed. The dimension, complexity and solving methods of the PEMFC model were discussed. The importance and validity to develop a model with time dimension are put forward.

Go to article

Mechanistic Study Of Oxidation Of Hypophosphite On Pt Electrodes By Sniftirs, Tai-Xiang Jiang, Hui-Huang Wu Nov 2002

Mechanistic Study Of Oxidation Of Hypophosphite On Pt Electrodes By Sniftirs, Tai-Xiang Jiang, Hui-Huang Wu

Journal of Electrochemistry

The oxidation of hypophosphite on a polycrystalline platinum electrode was studied by SNIFTIRS and cyclic voltammetry, the in-situ IR spectra were analyzed as a function of Pt electrode potentials in the solution of 0.5 mol/L H2SO4+0.1 mol/L NaH2PO2. It was found that the dissociative adsorption of hypophosphite ions occurs on Pt surface, and the oxidation product is H3PO4, rather than H2PO3- which was considered to produce on Ni electrodes, thereby a new insight into mechanism of hypophosphite oxidation on Pt in acidic media was …

Go to article

First Prev Next Last