Physical Chemistry Commons^™

Development Of Novel Adsorbent For Industrial Waste Water Treatment, Islam M. Al-Akraa, Hassan M. Shehata Eng, Dalia A. Ali Eng., Hoda A. Elsawy Dr

Chemical Engineering

The main objective of this research project is to perform some experimental procedures to inform the ability of the novel adsorbent used in this project. The chemical modification of the adsorbent is the chemical oxidation of pure powder chitosan using some specific redox pairs which are potassium dichromate and sodium bisulphite. After preparing the modified chitosan, there are some parameters that must be discussed during the adsorption process. The first parameter is the time parameter, showing experimentally the optimum time for adsorption under certain conditions by collecting values of absorbance and concentration of thymol blue adsorbed after the process from …

Correlating The Physicochemical Properties Of Magnesium Stearate With Tablet Dissolution And Lubrication, Julie L. Calahan

Theses and Dissertations--Pharmacy

Magnesium stearate (MgSt) is the most commonly used pharmaceutical excipient and is present in over half the tablet formulations on the market. In spite of its popularity as an effective lubricant, it has been repeatedly recognized that there is significant variability between MgSt samples, which can cause inconsistent lubrication between batches of MgSt. The hypothesis of this research is that the batch-to-batch variability in tablet lubrication and dissolution observed in tablet formulations containing different MgSt samples can be correlated with differences in MgSt physicochemical properties (fatty acid salt composition, crystal hydrate form, particle size and surface area). Developing correlations between …

Carbon Oxidation At The Atomic Level: A Computational Study On Oxidative Graphene Etching And Pitting Of Graphitic Carbon Surfaces, Simon Schmitt

Theses and Dissertations--Mechanical and Aerospace Engineering

In order to understand the oxidation of solid carbon materials by oxygen-containing gases, carbon oxidation has to be studied on the atomic level where the surface reactions occur. Graphene and graphite are etched by oxygen to form characteristic pits that are scattered across the material surface, and pitting in turn leads to microstructural changes that determine the macroscopic oxidation behavior. While this is a well-documented phenomenon, it is heretofore poorly understood due to the notorious difficulty of experiments and a lack of comprehensive computational studies. The main objective of the present work is the development of a computational framework from …

Recent Developments In The Pyscf Program Package, Qiming Sun, Xing Zhang, Samragni Banerjee, Peng Bao, Marc Barbry, Nick S. Blunt, Nikolay A. Bogdanov, George H. Booth, Jia Chen, Zhi-Hao Cui, Janus J. Eriksen, Yang Gao, Sheng Gun, Jan Hermann, Matthew R. Hermes, Kevin Koh, Peter Koval, Susi Lehtola, Zhendong Li, Junzi Liu, Narbe Mardirossian, James D. Mcclain, Mario Motta, Bastien Mussard, Hung Q. Pham, Artem Pulkin, Wirawan Purwanto, Paul J. Robinson, Enrico Ronca, Elvira R. Sayfutyarova, Maximillian Scheurer, Henry F. Schurkus, James E.T. Smith, Chong Sun, Shi-Ning Sun, Shiv Upadhyay, Lucas K. Wagner, Xiao Wang, Alec White, James Daniel Whitfield, Mark J. Williamson, Sebastian Wouters, Jun Yang, Jason M. Yu, Tianyu Zhu, Timothy C. Berkelbach, Sandeep Sharma, Alexander Yu Sokolov, Garnet Kin-Lic Chan

University Administration Publications

PySCF is a Python-based general-purpose electronic structure platform that supports first-principles simulations of molecules and solids as well as accelerates the development of new methodology and complex computational workflows. This paper explains the design and philosophy behind PySCF that enables it to meet these twin objectives. With several case studies, we show how users can easily implement their own methods using PySCF as a development environment. We then summarize the capabilities of PySCF for molecular and solid-state simulations. Finally, we describe the growing ecosystem of projects that use PySCF across the domains of quantum chemistry, materials science, machine learning, and …

Reactions At The Critical Point Of Solution, Jason Mote

Summer Community of Scholars Posters (RCEU and HCR Combined Programs)

No abstract provided.

Effect Of The Electrodeposition Potential Of Platinum On The Catalytic Activity Of A Pt/Gc Catalyst Toward Formic Acid Electro−Oxidation, Islam M. Al-Akraa, Bilquis A. Al-Qodami Ms., Ahmad M. Mohammad Prof

Chemical Engineering

The electrocatalytic activity of platinum (Pt)–modified glassy carbon (GC) (referred as Pt/GC) electrodes toward the formic acid electro−oxidation (FAO) was investigated. The Pt deposition on the GC substrate was carried out by a potentiostatic technique at different potentials (from 0.2 V to −0.2 V vs. Hg/Hg2Cl2/KCl (sat.) reference electrode) and the corresponding influence on the catalytic activity toward FAO was monitored. The electrocatalytic inspection revealed a potential role for the Pt deposition potential in boosting the catalytic efficiency of the catalyst toward FAO and further in mitigating the CO poisoning that eventually deactivate the catalyst. Interestingly, the highest activity toward …

A Spin-Coated Tiox/Pt Nanolayered Anodic Catalyst For The Direct Formic Acid Fuel Cells, Islam M. Al-Akraa, Ahmad M. Mohammad Prof

Chemical Engineering

The CO poisoning of the platinum anodic catalyst which typically functions the catalytic deterioration of the direct formic acid fuel cells could be minimized with a simple modification for Pt with titanium oxide. The fabrication scheme involved the spin-coating of a Ti precursor onto a Pt thin layer that was physically sputtered onto a Si substrate. The whole assembly was subjected to a post-annealing processing to produce the TiOx layer (60 nm) in a porous structure (mostly Anatase) atop of the Pt surface. The porous nature of the TiOx layer permitted the participation of Pt in the electrocatalysis of the …

Multi-Component Material For Solar Energy Conversion And Fundamentals Of Lead Acid Batteries, Crystal Ferels

Graduate Research Theses & Dissertations

Synthesis of complex inorganic materials is desirable because their complex composition allows more degrees of freedom and tunability, whose properties differ from their parent components. As an expansion on this concept, we synthesized a quinary compound Ce3FeWS3O6, using a molten flux method and a solvothermal method. The compound crystallizes into a hexagonal crystal system with space group P63/m. Its electric partition shows an anion with the form [(Ce3+)3W6+(S2-)3(O2-)6]3- forcing the transition metal Fe3+ state and leaving no conduction electrons, making the material a semiconductor. This compound is the right candidate as photoelectric material capable of absorbing photons from the solar …

Effects Of Hole Transporting Layers And Surface Ligands On Interface Energetics And Photovoltaic Performance Of Methylammonium Lead Iodide Perovskites, So Min Park

Theses and Dissertations--Chemical and Materials Engineering

Organic metal halide perovskites are promising materials for various optoelectronic device applications such as light emitting diodes (LED) and photovoltaic (PV) cells. Perovskite solar cells (PSCs) have shown dramatic increases in power conversion efficiency over the previous ten years, far exceeding the rate of improvement of all other PV technologies. PSCs have attracted significant attention due to their strong absorbance throughout the visible region, high charge carrier mobilities, color tunability, and ability to make ultralight weight devices. However, organic metal halide perovskites still face several challenges. For example, their environmental stability issue must be overcome to enable widespread commercialization. Meeting …

A Theoretical And Experimental Study Of Charge Transport In Organic Thermoelectric Materials And Charge Transfer States In Organic Photovoltaics, Ashkan Abtahi

Theses and Dissertations--Physics and Astronomy

Applications of organic electronics have increased significantly over the past two decades. Organic semiconductors (OSC) can be used in mechanically flexible devices with potentially lower cost of fabrication than their inorganic counterparts, yet in many cases organic semiconductor-based devices suffer from lower performance and stability. Investigating the doping mechanism, charge transport, and charge transfer in such materials will allow us to address the parameters that limit performance and potentially resolve them. In this dissertation, organic materials are used in three different device structures to investigate charge transport and charge transfer. Chemically doped π-conjugated polymers are promising materials to be used …

Structure, Morphology And Composition-Property Elucidation Of Ni–Mo And Ni−Mo−P Nanocrystals For Water Splitting Reactions And Group Iv Alloy And Silicate Nanocrystals For Visible To Near Ir Optoelectronics, Ebtesam Hassan Abuelenein Eladgham

Theses and Dissertations

Abstract

Structure, Morphology and Composition-Property Elucidation of Ni–Mo and Ni−Mo−P Nanocrystals for Water Splitting Reactions and Group IV Alloy and Silicate Nanocrystals for Visible to Near IR Optoelectronics

by

Ebtesam Hassan Abuelenein Eladgham

A dissertation submitted in partial fulfillment of the requirements for the degree of Doctor of Philosophy at Virginia Commonwealth University.

Advisor: Indika U Arachchige

Associate Professor, Department of Chemistry

Nanomaterials have gained a great attention because of their unique physical properties with size intermediate between molecular materials and extended solids. They have a large surface to volume ratio and display size tunable physical properties that was not …

Morphology Controlled Preparations And Electrochemical Properties Of Znco2O4 Electrode Materials For Supercapacitors, Yue-Shen Zhou, Meng Li, Shuang Wu, Zhao-Lei Li, Yan-Min Gao

Journal of Electrochemistry

In this work, hydrothermal reaction and high temperature were used to grow ZnCo₂O₄ active materials on Ni foam. The crystal stuctures and surface morphlogies of four samples were investigated by X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM) and transmission electron microscopy (TEM). The electrochemical performances were characterized by cyclic voltammetry (CV), galvanostatic charge/discharge (GCD) testing and electrochemical impedance spectroscopy (EIS) on an electrochemical station. It can be seen that active materials tended to form denser stuctures with an increasing amount of NH₄F in the solution system and four different morphologies of ZnCo_{2 …}

Electrochemical Preparation And Photocatalytic Performance Of Lanio3/Tio2 Nanotube Arrays, Cheng Gong, Ze-Yang Zhang, Si-Wan Xiang, Lan Sun, Chen-Qing Ye, Chang-Jian Lin

Journal of Electrochemistry

The LaNiO₃/TiO₂ nanotube arrays were prepared by pulse electrodeposition combined with high temperature annealing. The LaNiO₃ nanoparticles modified on the TiO₂ nanotube arrays had small particle size (< 10 nm), uniform distribution and controllable loading. Some LaNiO₃ nanoparticles were deposited inside the TiO₂ nanotubes. The UV-visible absorption spectra displayed that the absorption band edge of LaNiO₃/TiO₂ nanotube arrays was obviously red-shifted as compared with that of TiO₂ nanotube arrays, and the visible light absorption was enhanced significantly. The photocatalytic degradation results of rhodamine B (RhB) under visible light showed that the LaNiO₃/TiO₂ nanotube arrays prepared …

Electrochemical Determination Of Trace Copper Ions In Drinking Water Source, Jing-Ji Peng, Hong Zheng, Yi-Song Zou, Guo-Kun Liu, Dong-Xing Yuan

Journal of Electrochemistry

Aiming at the on-site and quick safety evaluation of the dissolved trace copper ions (Cu²⁺) in drinking water source, an electrochemical detection platform was developed on the basis of the square wave anodic stripping voltammetry using the gold nanoparticles (Au NPs) modified glassy carbon electrode, where Au NPs were deposited via electrochemical cyclic voltammetry. The proposed method displayed the limit of detection as low as 1.3 μg·L^-1 in the linear range of 2 ~ 50 μg·L^-1. The proposed method was applied to the determination of Cu²⁺ in the midstream of Minjiang River, one of …

Electrochemical Behaviors Of Azopurine On Gold Electrodes, Ming-Xue Li, Hang Shi, Jia Liu, Meng Zhang, Jian-Zhang Zhou, De-Yin Wu, Zhong-Qun Tian

Journal of Electrochemistry

In this paper, we studied the electrochemical behaviors of azopurine on polished gold electrodes with cyclic voltammetry (CV). On the basis of analyzing scan rate and peak current, it was supposed that the redox process belonged to a reversible process controlled by adsorption in 0.2 mol·L^-1 PBS (pH = 4.0 ~ 10.0) solutions. The potentials of redox peaks moved more negatively with increasing pH value. This proved that the H⁺ proton has participcted in the electrochemical reaction. The further data analysis and the calculation of surface adsorption excess demonstrated that the reaction was a two-proton and two-electron process. …

Electrochemical Cycling Stability Of Polyaniline Films In Different Color Ranges, Kun Xu, Kai-Ling Zhou, Hao Wang, Jing-Bing Liu, Hui Yan

Journal of Electrochemistry

The electrochromic behaviors of polyaniline films were investigated by potential step and cyclic voltammetry coupled with UV viscosity photometer. The polyaniline films show colorful changes from pale yellow to green and then to blue. Electrochromic stability, electrochemical behavior, coloring performance, optical properties and surface formations of the produced films were studied in detail. The working electrode was the flexible PANI electrode, and the counter electrode and the reference electrode were a platinum sheet and Ag/AgCl, respectively. The in situ optical transmittance of the PANI film at 650 nm was measured using an ultraviolet-visible-near-infrared spectrophotometer (Shimadzu UV-3101PC) combining with a square …

Polyaniline Coated Hollow Sulfur Prepared Using Sublimate 2,4,6-Tri(Propan-2-Yl)-1,3,5-Trioxane As Template For Sulfur Electrode, Zhang-Feng Li, Xiao-Rui Wang, Wen-Sheng Tian, Jin-Ze Yang, Ping Zhang, Li-Ping Ma, Yang Chen, Xiao-Li Cui, Zhi-Yu Jiang

Journal of Electrochemistry

An advance method for preparing polyaniline-coated hollow sulfur material using sublimate material ADD(2,4,6-tri(propan-2-yl)-1,3,5-trioxane) as a template was developed for lithium-sulfur battery. At first, the smashed ADD particles were coated by a sulfur layer through the reaction of Na₂S₂O₃ with diluted HCl. Then polyaniline layer was coated again on the surface of sulfur layer through the reaction of aniline with (NH₄)₂S₂O₈. After being dried at 60 ^oC for 12 h, the ADD in such a composite evaporated totally, and resulted in the formation of polyaniline-coated hollow sulfur …

Study On Electro-Sorption Of Heavy Metals And Sulfamethoxazole On Activated Carbon Fibers, Wen-Jun Zhao, Bing-Xin Jia, Ya-Nan Zhang, Jiu-Nian Guan, Jiao Qu, Ying Lu

Journal of Electrochemistry

To study the optimal removal condition, adsorption mechanism and comparative analysis of the three typical cationic pollutants, i.e., Zn(II), anionic pollutant Cr(VI) and molecular pollutant sulfamethoxazole (SMX), using self-made upflowed electro-sorption device for adsorptions of above three pollutants by modified activated carbon fiber were researched. The activated carbon fiber (ACF) was modified by hydrochloric acid. The ACF morphology and structure before and after modification were characterized by SEM, BET and FTIR. The characterization results show that the modified ACF had fewer surface impurities than the modified surface and the gully is more obvious, the specific surface area was increased by …

Bipolar-Membrane Electrodialysis Method To Treat Industrial High Saline Perfume Wastewater, Jian Zhang, Dong-Fang Niu, Shuo-Zhen Hu, Xin-Sheng Zhang

Journal of Electrochemistry

Large amount of organic saline wastewater is generated from various chemical industries. The contents of organic saline wastewater are more and more complicated as they are created from different types of industries. Directly discharging the organic saline wastewater without pre-treatment can generate severe environmental problem and waste useful resources. It is necessary to use an economical method to treat the organic saline wastewater and recover the salt into useful materials to achieve resource reuse. Bipolar-membrane electrodialysis (BMED) is one of the methods that can remove salt from the wastewater and convert it into certain acid and base with higher value …

Transient Electrochemical Surface-Enhanced Raman Spectroscopic Study In Electrochemical Reduction Of P-Nitrothiophenol, Yun Ling, Jing Tang, Guo-Kun Liu, Cheng Zong

Journal of Electrochemistry

P-nitrothiophenol (PNTP) is one of the most common probe molecules studied by surface-enhanced Raman spectroscopy (SERS). The research in electrochemical reduction behavior of PNTP will help understanding the mechanism for the nitrobenzene reduction. In this paper, we used transient electrochemical surface-enhanced Raman spectroscopy (TEC-SERS) to study the SERS of PNTP with cyclic voltammetry and chronoamperometry on gold electrodes. The results show that the TEC-SERS provide a time resolution that equals the transient electrochemical methods, and we concluded that the reaction was so quick that we did not observe the spectral information of intermediate species described in the literatures with a …

Electrochemical Properties Of Sulfur In Different Carbon Support Materials, Bo Zhang, Jia Liu, Xiao-Chen Liu, De-Jun Li

Journal of Electrochemistry

In order to investigate the effect of carbon structure on electrochemical performance of sulfur/carbon composite in lithium-sulfur battery, in this paper, sublimation sulfur was incorporated into three types of carbon materials, namely, graphene, carbon black and porous carbon. The three sulfur/carbon composites were characterized by scanning electron microscopy (SEM), Brunauer-Emmett-Teller (BET), and X-ray diffraction (XRD) techniques, and their electrochemical performances were also studied. The results showed that the sulfur/porous carbon composite offered an initial discharge capacity of 1623.2 mA·h·g^-1 and remained 845 mA·h·g^-1 after 100 cycles. Compared with graphene and carbon black, the mesopores and micropores in porous …

Electrochemical Sensor Based On Magnetic Electrode Modified With Magnetic Molecularly Imprinted Nanoparticles Immobilized Hemoglobin For Determination Of Hydrogen Peroxide, Yang Yuan, Jia-Xin Wang, Yu-Hua Cao

Journal of Electrochemistry

In this work, the surface-imprinted technique was used to prepare magnetic hemoglobin (Hb) imprinted nanoparticles, using Fe₃O₄@SiO₂ NPs as the carrier, Hb as the template molecule, and tetraethyl orthosilicate (TEOS) as the imprinted polymer monomer. The nanoparticles had a core-shell structure, with magnetic Fe₃O₄ NPs as the core and Hb imprinted polymers as the shell. Therefore, Hb could be concentrated and fixed on the surface of the magnetic imprinted nanoparticles (MMIPs NPs). Furthermore, MMIPs NPs were immobilized with chitosan (CS) on the surface of a magnetic electrode to constitute Hb enzyme-like biosensor …

An Aptasensor Based On Aunps/Pani/Tnts Nanocomposite For Electrochemical Detection Of Tobramycin, Yong-Ling Nong, Ni-Na Qiao, Ying Liang

Journal of Electrochemistry

A novel well-constructed electrochemical aptamer-based sensor for the detection of tobramycin was presented, using differential pulse voltammetry (DPV) as a detection technique and methylene blue(MB) as an electrochemical indicator. A glassy carbon electrode modified with a nanocomposite of Au nanoparticles/polyaniline/titania nanotubes (AuNPs/PANI/TNTs) was constructed as the electrode scaffold. The nanocomposite was characterized by transmission electron microscopy and X-ray photoelectron spectroscopy in detail. The results of cyclic voltammetry and electrochemical impedance measurements demonstrated that the AuNPs/PANI/TNTs nanocomposites can improve greatly the electron transfer on the interface. For the detection of tobramycin, the DPV results showed a linear relationship between the current …

Zif-67-Derived Ag/Co-Embedded N-Enriched Mesoporous Carbon For Oxygen Reduction Reaction, Zheng-Ling Di, Jing Zhu, Lei Dai, Wei Meng, Yue-Hua Li, Zhang-Xing He, Ling Wang

Journal of Electrochemistry

Nitrogen-doped porous carbon materials are considered as one of the most promising catalysts for oxygen reduction reaction (ORR). Herein, in order to further improve the activity of the nitrogen-doped porous carbon, Ag/Co bimetal is embedded into nitrogendoped porous carbon to form Ag/Co-embedded nitrogen-doped porous carbon material (AgCo@NC). The AgCo@NC was derived by the wet impregnation of Ag+ into ZIF-67 precursor, followed by chemical reduction and a subsequent pyrolysis process under Ar atmosphere at different temperatures (500 ℃, 600 ℃, 700 ℃). The morphologic characterization shows that the Ag/Co nanoparticles were successfully embedded in the mesoporous carbon framework with abundant nitrogen …

Quantitative Detection Of Levofloxacin Hydrochloride By Differential Pulse Stripping Voltammetry With Electrodeposited Bismuth Film Electrodes, Zi-Ying Guo, Zuo-Peng Li, Jiang Li, Jian-Guo Zhao, Feng Feng

Journal of Electrochemistry

In this study, differential pulse stripping voltammetry was developed for the quantitative detection of levofloxacin hydrochloride indirectly. Levofloxacin hydrochloride contains organic amine, which can be precipitated upon interaction with Zn(SCN)₄^2-. By means of differential pulse stripping voltammetry, the concentration of Zn²⁺ can be determined using an in-situ formed bismuth film electrode, which allows determining indirectly the amount of levofloxacine hydrochloride. The linearity equation, I = 1.1401c - 0.5309 with the correlative coefficient R = 0.9979, was presented in the experiment. The results showed that this approach is very sensitive, having a limitation of detection of 3.18 …

Ionic Liquid Assisted Synthesis Of Porous Carbons From Rice Husk For Supercapacitors, Han-Fang Zhang, Feng Wei, Jian Sun, Meng-Ying Jing, Xiao-Jun He

Journal of Electrochemistry

It is still a challenge to prepare carbon materials with high specific surface area at low cost from renewable resources. Herein, the authors report an efficient approach to synthesize porous carbons (PCs) from rice husk with ionic liquid (1-butyl-3-methylimidazolium hexafluorophosphate (BMIMPF₆)) as a template and an activation agent. The as-made PCs featured the high specific surface area up to 1438 m²·g^-1. As electrodes for supercapacitors, PCs showed a high specific capacitance of 256 F·g^-1 at 0.05 A·g^-1 in 6 mol·L^-1 KOH aqueous electrolyte and a good rate performance of 211 F·g …

Evaluation Of The Mechanisms And Effectiveness Of Nano-Hydroxides, Wood And Dairy Manure-Derived Biochars To Remove Fluoride And Heavy Metals From Water, Anna Rose Wallace, Wenjie Sun Dr, Chunming Su Dr

Civil and Environmental Engineering Theses and Dissertations

The development of effective treatment processes for the removal contaminants, such as fluoride and heavy metals, from polluted water have been urgently needed due to serious environmental health and safety concerns. In this dissertation, a variety of materials including various (hydro)oxide nanomaterials, biochars and surface modified biochar were studied to evaluate their effectiveness and mechanism on removing fluoride or mixed heavy metals from water.

In the Chapter 2, this study investigated the adsorptive removal of fluoride from water using various (hydro)oxide nanomaterials, focusing on ferrihydrite, hydroxyapatite (HAP) and brucite, which have the potential to be used as sorbents for surface …

Three-Dimensional Porous Vn Octahedron Catalyst With High Electrocatalytic Efficiency Toward Hydrogen Evolution Reaction, Can Yin, Wei-Wei Fu, Ling Fang, Shi-Li You, Hui-Juan Zhang, Yu Wang

Journal of Electrochemistry

With the rapid development of China’s economy, the demand for energy is increasing, and environmental problems are becoming more and more serious. The development and utilization of highly-clean new energy fuel can effectively alleviate the energy crisis and environmental pollution. Nowadays, exploring high-efficiency, environment-friendly and low-cost catalysts remains the focus of research in the hydrogen evolution reaction (HER). In this research, firstly, we proposed a three-dimensional porous vanadium nitride (VN) with octahedral structure, which was prepared by a calcination treatment method. The VN catalyst showed a good electrocatalytic activity toward HER, involving a small overpotential of 94.0 mV at -10 …

Influences Of Morphology And Nitrogen Doping On The Electrocatalytic Characteristics For Oxygen Reduction Reaction Of Nio/Rgo, Dong Liang, Heng-Yi Fang, Shuo Yao, Jie-Mei Yu, Zhao-Liang Zhang, Zhan-Kun Jiang, Xue-Ping Gao, Tai-Zhong Huang

Journal of Electrochemistry

In this research, the reduced graphene oxide (rGO) supported sheet-like NiO (NiO/rGO) and spherical-like NiO (NiO/N-rGO) catalysts for oxygen reduction reaction (ORR) were prepared. The structures, morphologies and chemical states of the two catalysts were characterized by X-ray diffraction (XRD), Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The electrochemical catalytic performance of the two catalysts for ORR were investigated by cyclic voltammetry (CV), Tafel, linear sweeping voltammetry (LSV), rotating disc electrode (RDE) and rotating ring disc electrode (RRDE) tests. Electrochemical results showed that the current density and onset potential (about 0.89 V) …

Preparation Of Nanostructural Mno-Porous Graphene Hybrid Material By Thermally-Driven Etching Of Mno For Lithium-Air Batteries, Juan Yang, Jun-Wei Lang, Peng Zhang, Bao Liu

Journal of Electrochemistry

In this paper, improving the surface morphology of graphene(GNSs) as designed concept. we describe a MnO/porous-graphene(MnO-PGNSs) was synthesized by a simple site-localized Mn²⁺ on GO (Mn-GO) by charge adsorption and then driving by high-temperature calcination, growing MnO nanoparticles and etching GNSs achieved on step. And Then focus on the key factors of influenced the etch hole formation are analyzed, founded the dispersion of Mn-GO; layer number of GO and calcination temperature also affected the formation of holes. In addition, the MnO-PGNSs as lithium-air battery cathode exhibits high reversible capacity compared with GNSs and PGNs and it is able to …