Open Access. Powered by Scholars. Published by Universities.®

Physical Chemistry Commons™

Open Access. Powered by Scholars. Published by Universities.®

Electrical and Computer Engineering

Institution
Keyword
Publication Year
Publication
Publication Type

Articles 1081 - 1110 of 1310

Full-Text Articles in Physical Chemistry

Synthesis And Electrochemical Characteristics Of Nickel-Based Complex Oxide LiANi0.78Co0.2Cd0.02O2, Rong-Zhong Yuan, Mei-Zhen Qu, Zuo-Long Yu May 2003

Synthesis And Electrochemical Characteristics Of Nickel-Based Complex Oxide LiANi0.78Co0.2Cd0.02O2, Rong-Zhong Yuan, Mei-Zhen Qu, Zuo-Long Yu

Journal of Electrochemistry

The nickel-based complex oxide LiaNi0.78Co0.02O2 cathode materials for lithium-ion rechargeable batteries was synthesized by the improved solid-state reaction method with LiOH·H2O, ball-like Cd-doped Ni(OH)2 and Co2O3 as raw materials. The analysis ICP-AES proved that the as-prepared compounds were near the stoichiometric form. The XRD, SEM and electrochemical characteristics testing were also carried out. The results showed that the complex cathode material LiaNi0.78Co0.2Cd0.02O2 has layered structure, homogeneous surface distributions,uniform particles with good crystal morphology as well as stable electrochemical …

Go to article

Perfluorinated Sulfonic Acid Lithium Conductivity Humidity Sensor, Hong-Feng Xu, Jing Liu, Li Wan May 2003

Perfluorinated Sulfonic Acid Lithium Conductivity Humidity Sensor, Hong-Feng Xu, Jing Liu, Li Wan

Journal of Electrochemistry

Treat carbon paper with 3% PTFE solution and dried in 340 ℃ for 40 minutes to enhance its intension, and level off the surface of the carbon paper with a mixture of XC-72 carbon black and PTFE solution. With those treated carbon paper as electrodes, recast Nafion thin film from 5% Nafion solution as humidity sensitive material, a solid polymer electrolyte humidity sensor was prepared on a thin PET film. Take the relative humidity data from several saturated salt solutions, the relationship between conductivity response and relative humidity was studied at different relative humidies .The results showed: when the polymer …

Go to article

Conductance Properties For Electrolyte Of Lithium Ion Battery At Low Temperature, Jing-Li Han, Yan-Mei Yu, Jian Chen, Chun-Tong Wang May 2003

Conductance Properties For Electrolyte Of Lithium Ion Battery At Low Temperature, Jing-Li Han, Yan-Mei Yu, Jian Chen, Chun-Tong Wang

Journal of Electrochemistry

The system of LiPF6-ethylene carbonate (EC)-methy1 acetate (MA) was studied. The conductivities of this system were measured under various composition and various salt concentrations at temperature range of 20～-50 ℃. The optimum composition of this system was selected. The tests of cyclic voltammography and charge-discharge were carried out. This system was compared with commercial electrolyte solution.

Go to article

Corrosion Prediction Of Carbon Steel In Concentrated Lithium Bromide Solutions At High Temperature Using Bp Neural Network, Nai-Bao Huang, Cheng-Hao Liang May 2003

Corrosion Prediction Of Carbon Steel In Concentrated Lithium Bromide Solutions At High Temperature Using Bp Neural Network, Nai-Bao Huang, Cheng-Hao Liang

Journal of Electrochemistry

Neutral network model has been developed for the computation of corrosion rate of carbon steel in LiBr solutions.The results indicate that the model is capable of reproducing the effects of changes in alkalinity, temperatures, LiBr and Na2MoO4 concentrations on the rates of general corrsion and good agreement between calculated and experimental corrosion rate is obtained. The model can be used to satisfactorily predict the corrosion rate of carbon steel in different concentrations of LiBr solutions containing different inhibitors at different temperatures. It also provides a novel method for corrosion monitoring of metals used in LiBr absorption chiller.

Go to article

Magnetic Resonance Studies On Lithium Intercalation Into Carbons, Xiao-Rong Zhou, Zhen-Ming Du, Lin Zhuang, Jun-Tao Lu Feb 2003

Magnetic Resonance Studies On Lithium Intercalation Into Carbons, Xiao-Rong Zhou, Zhen-Ming Du, Lin Zhuang, Jun-Tao Lu

Journal of Electrochemistry

The electron spin resonance(ESR) and 7Li-NMR magnetic resonance (7Li-NMR) studies on lithium intercalation into carbons were reviewed based on recently published papers, including those by the authors of this review. Two kinds of electronic spins were found in ESR studies. One corresponds to the charge carrier electrons and is called the Pauli spin. From the ESR intensity of Pauli spins, the curve of the density of electronic states can be deduced for the carbon material studied and, in turn, the contribution of the band model mechanism to the lithium intercalation can be calculated for the given carbon sample. The other …

Go to article

The Electrochemical Performance Studies On Novel Lifepo4 Cathode Materials For Li-Ion Batteries, Zhi-Cong Shi, Chen Li, Yong Yang Feb 2003

The Electrochemical Performance Studies On Novel Lifepo4 Cathode Materials For Li-Ion Batteries, Zhi-Cong Shi, Chen Li, Yong Yang

Journal of Electrochemistry

The cathode materials of LiFePO4 and  LiFePO4 coated with carbon were synthesized by means of solid state reaction and ballmilling. The samples were characterized by X-ray diffraction, scanning electron microscopy, gas-phase element analysis and titration analysis methods. Electrochemical tests of two kinds of materials showed that both of them exhibit a 3.4V discharge voltage plateau, however, the coated samples demonstrated the improved performance in terms of discharge capacity and cyclic stability.

Go to article

The Study On The Synthesis And Electrochemical Property Of K2Feo4, Yong-Long Wang, Ning Zhou, Shi-Hai Ye, Xue-Ping Gao, Feng Wu, Zuo-Xiang Zhou, De-Ying Song Feb 2003

The Study On The Synthesis And Electrochemical Property Of K2Feo4, Yong-Long Wang, Ning Zhou, Shi-Hai Ye, Xue-Ping Gao, Feng Wu, Zuo-Xiang Zhou, De-Ying Song

Journal of Electrochemistry

The synthesis,characterization and electrochemical property of K2FeO4 for positive materal of lithium ion battery were studied. K2FeO4 with low purity was gained through the reaction of KCIO and Fe(NO3)3 in KOH solution and after recrystalization the purity of K2FeO4 reached 97%～98%. The methods of XRD and FTIR were used to measure the structure of K2FeO4 and its initial discharge performance was tested.

Go to article

Study Of Electrochemical Lithium Intercalation Performance Of Ni0.67Mg0.33O, Zhen-Cai Huang, Mao-Hui Chen, Guo-Tao Wu, Jin-Kua You, Zu-Geng Lin Feb 2003

Study Of Electrochemical Lithium Intercalation Performance Of Ni0.67Mg0.33O, Zhen-Cai Huang, Mao-Hui Chen, Guo-Tao Wu, Jin-Kua You, Zu-Geng Lin

Journal of Electrochemistry

In the present work, Ni0.67Mg0.33O and NiO were produced by sol-gel method, and characterized by XRD, a rietveld refinement and the discharge/charge test.It was found that the magnesium-doping restrained the reduction of Ni and decreased the reversible capacity for the sample of Ni0.67Mg0.33O. But the formation of the solid solution after the magnesium-doping facilitated the high dispersion of NiO, and accordingly improved the electrochemical performance.

Go to article

Application Of Biphenyl Electroploymerization For Overcharge Protection In Li-Ion Batteries, Li-Fen Xiao, Xin-Ping Ai, Yu-Liang Cao, Han-Xi Yang Feb 2003

Application Of Biphenyl Electroploymerization For Overcharge Protection In Li-Ion Batteries, Li-Fen Xiao, Xin-Ping Ai, Yu-Liang Cao, Han-Xi Yang

Journal of Electrochemistry

The electropolymerization of biphenyl at overcharged positive electrode was investigated for overcharge protection of Li-ion batteries. Biphenyl in electrolyte as an additive can electrochemically polymerize at 4.5～4.75 V(vs. Li/Li+) to form a layer of conductive film on cathode surface. The surface film increases the internal resistance and the gases released during the electropolymerization also increases the internal pressure of the batteries, which therefore enhance the sensitivities of the electrical disconnecting devices. During prolonged overcharge, the growth of the conductive polymer film can create short circuit between the positive and negative electrodes and cause self-discharge of the batteries to …

Go to article

An Eqcm Study Of Water Adsorption And Oxidation On Pt Electrodes In Sulfate Acid Sulotions, Heng Lin, Sheng-Pei Chen, Jin-Mei Lin, Ai-Lan Lin, Guo-Liang Chen Feb 2003

An Eqcm Study Of Water Adsorption And Oxidation On Pt Electrodes In Sulfate Acid Sulotions, Heng Lin, Sheng-Pei Chen, Jin-Mei Lin, Ai-Lan Lin, Guo-Liang Chen

Journal of Electrochemistry

Simultaneous frequency and current responses during potential cycling of Pt electrode were measured in 0.1 mol·L-1 H2SO4 solution by using EQCM. Quantitative analysis of the mass change revealed that the increase of mass in the hydrogen and double-layer regions in a positive-going potential scan was due to water adsorption on the Pt electrode, further calculation indicated that water molecules adsorbed on Pt electrode in the double-layer regions through a low discharge quomodo .The EQCM studies provided quantitative results of surface mass variation during water adsorption and oxidation,and have thrown new light in elucidating the structure of …

Go to article

Synthesis By Complexation Processes And Characterization Of Lini0.8Co0.2O2 Cathode Materials, Jing Liu, Zhao-Yin Wen, Zhong-Hua Gu, Xiu-Jian Zhu, Zu-Xiang Lin Feb 2003

Synthesis By Complexation Processes And Characterization Of Lini0.8Co0.2O2 Cathode Materials, Jing Liu, Zhao-Yin Wen, Zhong-Hua Gu, Xiu-Jian Zhu, Zu-Xiang Lin

Journal of Electrochemistry

The layered LiNi0.8Co0.2O2 compound, which has been of great interest for lithium ion batteries, was prepared at low temperatures by calcining a complex precursor at different temperatures. The physical properties of the synthesized cathode materials were discussed in the light of structural (XRD). The charge and discharge cycling of the cells containing the synthesized oxide as the positive electrode in conjunction with lithium metals and employing a non-aqueous electrolyte showed that LiNi0.8Co0.2O2 treated at 900 ℃ exhibited excellent performances. The first discharge capacity of LLiNi0.8Co0.2O2 …

Go to article

Fabrication Of SncuX/Cms Composite Materials For Lithium-Ion Batteries, Yu Liu, Jing-Ying Xie, Jun Yang, Ke Wang, Bao-Feng Wang Feb 2003

Fabrication Of SncuX/Cms Composite Materials For Lithium-Ion Batteries, Yu Liu, Jing-Ying Xie, Jun Yang, Ke Wang, Bao-Feng Wang

Journal of Electrochemistry

The composite material were prepared by sub-ctrochemical cycling tests showed that coulombic efficiency of the electrodes prepared by the composite materials was near 100 % after second cycle and the capacity dropped less than 5% after the 30th cycle, versus 390 mAh⋅g-1 special capacity, improving 26% special capacity of pure CMS electrode. The electrochemical performance of the composite materials is depended strongly on the alloy content in the composite, the addhesive strength between alloy particles and CMS matrix, the distribution of particles on the surface of CMS and the particle size of alloy. The composite material can be applied …

Go to article

Fenton Reagent Produced In Electrolysis Cell And Its Using In Degradation And Decolourization Of Dye, Xi Zheng, Ri-Yao Chen, Rui-Fang Lan, Xiao Chen, Zhen Chen Feb 2003

Fenton Reagent Produced In Electrolysis Cell And Its Using In Degradation And Decolourization Of Dye, Xi Zheng, Ri-Yao Chen, Rui-Fang Lan, Xiao Chen, Zhen Chen

Journal of Electrochemistry

The electro-chemical processing to produce Fenton reagent has been described. Fenton reagent having a high redox potential has been used as an oxidant in treatment of dye wastewater. Results show that both of the degradation and decolourization of dyes are efficient. The decolourization of dye wastewater reaches 100%.The COD removing rate is about 80%.

Go to article

Electroreduction Of Cd(Ⅱ) In Dmso And Complexation Of Cd(Ⅱ) With Coumarin Derivates, Ji-Guo Song, Hua-Can Song, Qi-Qin Yang, Yi-Wen Chen, Zun-Le Xu Feb 2003

Electroreduction Of Cd(Ⅱ) In Dmso And Complexation Of Cd(Ⅱ) With Coumarin Derivates, Ji-Guo Song, Hua-Can Song, Qi-Qin Yang, Yi-Wen Chen, Zun-Le Xu

Journal of Electrochemistry

Cadmium p-toluenesulfonate was synthesized and tested electrochemically for the first time. This salt can lose all the hydrated water easily and the dehydrated salt do not deliquesce in the air.Hence,the cadmium p-toluenesulfonate is suitable for the electrochemical studies in organic solvents.When the Cd(Ⅱ) reduced on Pt electrode in Cd(p-CH3C6H4SO3)2+TBAP+DMSO, underpotential deposition of cadmium occurred at first, and then cadmium deposited. 4-Methyl-7-hydroxylcoumarin and 3-aminocoumarin coordinate with Cd(Ⅱ) respectively, as a result the reductive potentials of Cd(Ⅱ) moved to the negative direction.

Go to article

Lithium Intercalation Performance Of P-Doped Phenolic Resin Pyrolysis Carbon, Bao-Hua Li, Kai-Xi Li, Yonggen Lv, Chun-Xiang Lv, Dong Wu, Li-Cheng Ling Nov 2002

Lithium Intercalation Performance Of P-Doped Phenolic Resin Pyrolysis Carbon, Bao-Hua Li, Kai-Xi Li, Yonggen Lv, Chun-Xiang Lv, Dong Wu, Li-Cheng Ling

Journal of Electrochemistry

Phosphorus-doped phenolic resin carbon was prepared by low temperature (700 ℃) pyrolysis of thermoplastic phenolic resin containing different amounts of phosphorus pentoxide after curing. X-ray diffraction pattern and the constang-current charge-discharge properties of phenolic resin carbon were studied. The results showed that the phenolic resin carbon microstructure became out of order with increasing of content phosphorus pentoxide, otherwise, the first discharge reversible capacities increased firstly and then decreased. The first discharge reversible capacity of phenolic resin carbon containing 9wt% phosphorus pentoxide was 528 mA·h·g-1 which was higher than that of non-phosphorus doped phenolic resin carbon(230 mA·h·g-1) did.

Go to article

Steady State Simulation Of Ysz Intermediate-Temperature Fuel Cell, Zi-Jing Lin, Ye Gu, Xiao-Hua Zhang Nov 2002

Steady State Simulation Of Ysz Intermediate-Temperature Fuel Cell, Zi-Jing Lin, Ye Gu, Xiao-Hua Zhang

Journal of Electrochemistry

With a coupled 2D electrochemical and thermal modeling software, the characteristics of the steady state operation of the intermediate-temperature fuel cell with thin yttria-stabilized zirconia(YSZ) electrolyte was analyzed. The parameters of I-V equation were obtained from fitting the experiment results and the choice of grid points was determined by balancing the accuracy requirement and computational efficiency. The temperature fields at different operation circumstances such as flow designs, material choices for interconnect, were examined. The dependences of the output power and cell efficiency on the operating voltage at different temperatures were studied. Based upon the analysis of the temperature profile, it …

Go to article

Preparation And Performance Of Lifeo2 Coated Nickel Oxide Cathode For Molten Carbonate Fuel Cells, Chun-Ming Wang, Fei Li, Ke-Ao Hu Nov 2002

Preparation And Performance Of Lifeo2 Coated Nickel Oxide Cathode For Molten Carbonate Fuel Cells, Chun-Ming Wang, Fei Li, Ke-Ao Hu

Journal of Electrochemistry

A novel cathode for molten carbonate fuel cells was prepared by coating LiFeO2 over the surface of porous NiO cathode by a simple combustion process. The analytical results of X-ray diffraction (XRD), energy dispersive analysis of X-ray (EDAX), scanning electron microscopy (SEM) and transmission electron microscopy (TEM) indicated that the LiFeO2 coating on the surface of NiO particles consisted of nonometer-sized LiFeO2 grains and sintered tightly with the NiO particles. The LiFeO2 coating dramatically reduced the contacting area of NiO with the carbonate melts, thus the solubility of NiO in the carbonate melts was decreased. Meanwhile, …

Go to article

Review Of Mathematical Model For Proton Exchange Membrane Fuel Cell, Shan-Hai Ge, Bao-Lian Yi, Hua-Min Zhang Nov 2002

Review Of Mathematical Model For Proton Exchange Membrane Fuel Cell, Shan-Hai Ge, Bao-Lian Yi, Hua-Min Zhang

Journal of Electrochemistry

In the review with 49 references, the mathematical models for proton exchange membrane fuel cell (PEMFC) were summarized. The mechanistic model and empirical model were introduced. Transfer in the membrane, catalyst layer, diffusion layer and flow field of PEMFC were described. The importance of water and heat management was analyzed. The dimension, complexity and solving methods of the PEMFC model were discussed. The importance and validity to develop a model with time dimension are put forward.

Go to article

Mechanistic Study Of Oxidation Of Hypophosphite On Pt Electrodes By Sniftirs, Tai-Xiang Jiang, Hui-Huang Wu Nov 2002

Mechanistic Study Of Oxidation Of Hypophosphite On Pt Electrodes By Sniftirs, Tai-Xiang Jiang, Hui-Huang Wu

Journal of Electrochemistry

The oxidation of hypophosphite on a polycrystalline platinum electrode was studied by SNIFTIRS and cyclic voltammetry, the in-situ IR spectra were analyzed as a function of Pt electrode potentials in the solution of 0.5 mol/L H2SO4+0.1 mol/L NaH2PO2. It was found that the dissociative adsorption of hypophosphite ions occurs on Pt surface, and the oxidation product is H3PO4, rather than H2PO3- which was considered to produce on Ni electrodes, thereby a new insight into mechanism of hypophosphite oxidation on Pt in acidic media was …

Go to article

Preparation And Electrochemical Lithium Intercalation Performance Of Different Shaped Carbon Nanotube, Mao-Hui Chen, Zhen-Cai Huang, Guo-Tao Wu, Jin-Kua You, Zu-Geng Lin Nov 2002

Preparation And Electrochemical Lithium Intercalation Performance Of Different Shaped Carbon Nanotube, Mao-Hui Chen, Zhen-Cai Huang, Guo-Tao Wu, Jin-Kua You, Zu-Geng Lin

Journal of Electrochemistry

In the present work, different shaped carbon nanotubes were produced by the general CVD and the template method at different temperature (600 ℃,700 ℃) with the reaction gas of acetylene. The morphology, structure and the electrochemical lithium intercalation performance were comparatively studied and characterized by TEM, HRTEM, SEM, XRD, Raman techniques and Charge/Discharge Test. It was found that the different preparation methods and temperatures all had an obvious effect on these properties of carbon nanotubes. In our samples, with the increase of preparation temperature, the degree of crystallinity decreased, and the reversible specific capacity increased respectively.

Go to article

Nano-Sized Cobalt-Based Oxides As Negative Electrode For Lithium-Ion Batteries, Feng Huang, Zheng-Yong Yuan, Yun-Hong Zhou, Ju-Tang Sun Nov 2002

Nano-Sized Cobalt-Based Oxides As Negative Electrode For Lithium-Ion Batteries, Feng Huang, Zheng-Yong Yuan, Yun-Hong Zhou, Ju-Tang Sun

Journal of Electrochemistry

Nanosized cobalt-based oxide (Co3O4, CoB1.36O2.8 and CoB0.5Al0.1O1.5) samples were prepared by rheological phase method and were tested as anodes in secondary lithium batteries. The cells were cycled between 0.01V and 3.00 V. The best electrochemical performance was obtained from the Co3O4 cell, which retained 95% of its initial capacity (931 mAh/g) after 30 cycles. The doping of B, Al reduced the reversible capacity during the first discharge/charge cycle, and the quantity of reversible capacity reduced with B, Al increasing. The modifying structures at difference …

Go to article

Properties Of Domestic Natural Graphite Used For Li-Ion Batteries, Cui-Wei Du, Yu-Juan Zhao, Gang Zhang, Yin-Shun Wu, Qing-Guo Liu Nov 2002

Properties Of Domestic Natural Graphite Used For Li-Ion Batteries, Cui-Wei Du, Yu-Juan Zhao, Gang Zhang, Yin-Shun Wu, Qing-Guo Liu

Journal of Electrochemistry

The structure, physical characteristics and electrochemical properties of the natural graphite produced in Shandong province have been studied. The result of X-ray diffraction showed that the graphite consisted of hexagonal structure and rhombic structure (30% rhombic structure). It was fine crystal graphite. Used as a negative material of Lithium ion battery, the natural graphite showed excellent voltage and high energy capacity, but poor compatibility with electrolyte solution containing propylene carbonate (PC) for its own structure limitation.

Go to article

Electrocatalytic Oxidation Of Formic Acid On Molybdate-Modified Platinum Electrode, Jun-Hua Du, Xue-Hui Xu, Hong Li, Hong-Yu Cheng, Wei-Shan Li Nov 2002

Electrocatalytic Oxidation Of Formic Acid On Molybdate-Modified Platinum Electrode, Jun-Hua Du, Xue-Hui Xu, Hong Li, Hong-Yu Cheng, Wei-Shan Li

Journal of Electrochemistry

The electrochemical behavior of molybdates on a platinum electrode in H2SO4 solutions with different H2SO4 concentrations was studied by cyclic voltammetry and double chronoamperometry. Molybdates were reduced to adsorb hydrogen molybdenum bronzes on the platinum electrode in H2SO4 solutions during cathodically potential sweep. The hydrogen molybdenum bronzes were oxidized to different forms of hydrogen molybdenum bronzes with less hydrogen, depending on the H2SO4 concentration. Platinum electrode was modified by these hydrogen molybdenum bronzes. However, this modified electrode was not stable in H2SO4 solutions. The modified …

Go to article

Manufacture Of 1 Kw Molten Carbonate Fuel Cell Stack, Sheng Sui, Xin-Jian Zhu, Zheng-Yu Fan, Guang-Yi Cao Nov 2002

Manufacture Of 1 Kw Molten Carbonate Fuel Cell Stack, Sheng Sui, Xin-Jian Zhu, Zheng-Yu Fan, Guang-Yi Cao

Journal of Electrochemistry

A molten carbonate fuel cell stack with an active area of 240 mm×140 mm consisted of 30 cells. The gas feed system works via interior manifolds, and the stack placed in a couple of self-chest, coupled with a heater at the bottom and other fours surrounded,to keep uniformity of temperature.Under ambient pressure and 650 ℃, fed with hydrogen and air as anode and cathode gases respectively, the stack gave a current density of 150 mA/cm2 at an average cell voltage of 0.7 V. The peak output of the stack was 1.06 kW during its performance of 300 h.

Go to article

Optimum Of Catalyst Layers For Direct Methanol Fuel Cells, Jun Zhang, Lei Li, Li Xu, Yu-Xin Wang Aug 2002

Optimum Of Catalyst Layers For Direct Methanol Fuel Cells, Jun Zhang, Lei Li, Li Xu, Yu-Xin Wang

Journal of Electrochemistry

The performances of membrane electrode assemblies (MEAs)with various Pt loading were compared. The amount of Nafion in a catalytic layer was optimized, and the effect of Nafion loading on the resistance of MEAs was investigated with ac impedance spectroscopy. For a MEA with both Pt 4 mg/cm2 in the anode and the cathode, suitable Nafion loading was 21.4 wt% in the anode. With 21.4 wt% Nafion loading in the cathode, the Direct Methanol Fuel Cells(DMFC) showed the highest performance at high current density. While, the DMFC performances came down, as Nafion loading increasing,for ohm and concentration polarization.

Go to article

Study On Modification Of Spinel Limn2O4 By Overcoating, Ren-Gang Zhang, Shi-Xi Zhao, Jung-Lei Xia, Han-Xing Liu Aug 2002

Study On Modification Of Spinel Limn2O4 By Overcoating, Ren-Gang Zhang, Shi-Xi Zhao, Jung-Lei Xia, Han-Xing Liu

Journal of Electrochemistry

The surface of spinel LiMn2O4 was modified by the sol-gel process with LiCoO2-coated LiMn2O4 and studied by XRD, SEM and EPMA. The results have shown that the surface of the coated grains heated at 700 ℃ for 10h, which is cubic spinel, were Co-rich. The amount of Co3+ in the grains changed owing to different place of the grain and decreased from surface to inner parts. Using the coated as the cathode of Li-ion cells, the initial capacity deceased slightly, but the amount of Mn2+ solving in electrolyte decreased, Jahn-Teller …

Go to article

Some Consideration For Lithium-Ion Cells' Safety, Guang-Xia Hu, Jing-Ying Xie Aug 2002

Some Consideration For Lithium-Ion Cells' Safety, Guang-Xia Hu, Jing-Ying Xie

Journal of Electrochemistry

The safety is the most important problem for lithium ion cells, especially for large lithium ion cells. In this paper, some information about lithium ion cells' safety can be learned by discussing several aspects of lithium ion cells, such as, materials of lithium ion cell, manufacturing processes, using conditions and so on.

Go to article

Synthesis And Characterization Of Lini0.8-XAlXCo0.2O2 As Cathodes For Lithium-Ion Batteries, Jun Zhang, Zhong-Kao Jin, Qing-He Yang, Qing-Mei Song, Xiao-Hua Ma, Xiang-Fu Zong Aug 2002

Synthesis And Characterization Of Lini0.8-XAlXCo0.2O2 As Cathodes For Lithium-Ion Batteries, Jun Zhang, Zhong-Kao Jin, Qing-He Yang, Qing-Mei Song, Xiao-Hua Ma, Xiang-Fu Zong

Journal of Electrochemistry

Single-phase solid solution of LiNi0.8-xAlxCo0.2O2 (0≤ x <0.1)had been synthesized and characterized by X-ray diffraction(XRD) and scanning electron microscopy (SEM). Their electrochemical performance was examined by charge-discharge cycling. The LiNi0.71Al0.09Co0.2O2 compound showed a discharge capacity of 152 mAh/g after 20 cycles that corresponds to 97.4% capacity retention. The beneficial effect of co-doping with Al and Co elements was corro-borated by slow scanning cyclic voltammograms(SSCV), electrochemical impedance spectrum (EIS) and differential scanning calorimetry (DSC) data on charged cathodes. These results show that the 2D-character of the crystal lattice was stabilized by co-doping with Al and Co, the phase transitions that occur during deintercalation or intercalation of Li-ions were significantly suppressed, …

Go to article

Research Progress On Electrode Material In All-Vanadium Redox Battery, Hua Li, Shou-Wen Chang, Chuan-Wei Yan Aug 2002

Research Progress On Electrode Material In All-Vanadium Redox Battery, Hua Li, Shou-Wen Chang, Chuan-Wei Yan

Journal of Electrochemistry

An all-vanadium redox flow storage battery possesses many advantages over conventional storage batteries.The development statue of two types electrode materials (metal and compound type) is introduced in this article.

Go to article

Initial Stages Of Copper Electrodeposition On Glassy Carbon Electrode, Ling Huang, Rui Zhang, Min Gu, Fang-Zu Yang, Shu-Kai Xu, Shao-Min Zhou Aug 2002

Initial Stages Of Copper Electrodeposition On Glassy Carbon Electrode, Ling Huang, Rui Zhang, Min Gu, Fang-Zu Yang, Shu-Kai Xu, Shao-Min Zhou

Journal of Electrochemistry

Initial stages of copper electrodeposition on glassy carbon electrode from acid sulphate solutions were studied using cyclic voltammetry and chronoamperometry. The electrolyte solution was a 0.05 mol.L-1 copper sulphate, 1.4～1.8 mol⋅L-1 sulphuric acid containing 1 mg·L-1 2-mercaptobenzoimidazole, Results show that 2-mercaptobenzoimidazole produced an inhibition of the copper deposition, probably related to the adsorption,sulphuric acid promote copper electrodeposition. The initial deposition kinetics corresponded to a model including instantaneous nucleation and diffusion controlled growth.Addition of 2-mercaptobenzoimidazole and sulphuric acid did not change the initial nucleation of copper electrocrystallization, it increased the nucleation rate and the number density of nuclei …

Go to article

First Prev Next Last