Open Access. Powered by Scholars. Published by Universities.®

Physical Chemistry Commons™

Open Access. Powered by Scholars. Published by Universities.®

Chemical Engineering

Institution
Keyword
Publication Year
Publication
Publication Type

Articles 661 - 690 of 860

Full-Text Articles in Physical Chemistry

Degradation Of Aniline Wastewater By Electro-Heterogeneous Catalysis Reactor, Wei-Li Liu, Ai-Li Zhang, Ji-Ti Zhou, Bao-Jun Jia, Qun-Li Zhu Feb 2006

Degradation Of Aniline Wastewater By Electro-Heterogeneous Catalysis Reactor, Wei-Li Liu, Ai-Li Zhang, Ji-Ti Zhou, Bao-Jun Jia, Qun-Li Zhu

Journal of Electrochemistry

The treatment of aniline wastewater was investigated using novel electro-heterogeneous catalysis reactor.The effects of applied cell voltage,electrolysis lime,pH value and the electrolyte on electrolysis were investigated.The experimental results show that the reactor with a cell voltage of 30 V,an electrolysis time of 1 h,pH value of 7 and a salinity of 800 mg/L can achieve the best removal efficiency on aniline,which is more efficient than the sole electrochemical reactor.

Go to article

Electrocatalytic Oxidation Of Glucose On Nano Pt/C Electrode, Cui-Lian Chen, Xiao-Lan Wei, Pei Kang Shen Feb 2006

Electrocatalytic Oxidation Of Glucose On Nano Pt/C Electrode, Cui-Lian Chen, Xiao-Lan Wei, Pei Kang Shen

Journal of Electrochemistry

Nano Pt/C electrocatalysts were prepared by intermittent microwave heating method.The electrooxidation of glucose on smooth Pt and～Pt/C electrodes has been studied and compared.The results showed that the electrochemical properties on nano Pt/C were improved due to the reduction of the overpotential and the increase in the kinetic rate.The surface area would be significantly increased when the particle size of the catalyst was reduced to nano-scale,resulting in the increase in the activity.The enhancement in the resistance to poisoning could be explained that the oxygen-containing species are easier to react with poisoning species on nano Pt/C and re-active the electrode.

Go to article

The Effect Of Solution Concentration On Properties Of Ru-Ti-Ir Oxide Anode Coatings, Ke Wang, Yan Han, Jun-Tao Wang, Xiao-Ling Zhang, Yu-Pu Sun Feb 2006

The Effect Of Solution Concentration On Properties Of Ru-Ti-Ir Oxide Anode Coatings, Ke Wang, Yan Han, Jun-Tao Wang, Xiao-Ling Zhang, Yu-Pu Sun

Journal of Electrochemistry

The anode coatings of Ru-Ti-Ir oxide with various solution concentrations were prepared by thermal decomposition.The scanning electron microscope(SEM),energy dispersive X-ray detector(EDX),X-ray diffraction(XRD),accelerated life,polarization curve,cyclic voltammetry and electrochemical impedance.spectroscopy(EIS)tests were carried out.The results showed that there was an obvious effect of solution concentrations on the morphology of the coatings,but little effect on polarization of chlorine evolution.Voltammetric charges and double layer capacitances of anode coatings had a tendency to fall down firstly then increase afterwards as the solution concentration increased.

Go to article

Electrochemical Reduction Behavior Of Benzaldehyde In The Ionic Liquids, Ning Zhao, Wen-Ju Dong, Qi-Zeng Shi Feb 2006

Electrochemical Reduction Behavior Of Benzaldehyde In The Ionic Liquids, Ning Zhao, Wen-Ju Dong, Qi-Zeng Shi

Journal of Electrochemistry

In this paper, the electrochemical reduction of benzaldehyde was investigated in C4MIMBF4, C6MIMBF4  and C8MIMBF4 ionic liquids by cyclic linear sweep voltammetry,cyclic square-wave voltammetry and chronocoulometry.Benzaldehyde exhibits two successive one-electron irreversible reduction(EP1=-1.39 V, EP2=1.69 V) with GC electrode in C4MIMBF4, the voltammetric data for benzaldehyde give diffusion coefficients of 1.5*10-8cm2/s and 1.3*108cm2/s. There is one current peak in C6MIMBF4  and C8MIMBF4 ionic liquids due to their stronger alkalinity …

Go to article

Oxygen Enrichment Effect Of Ceo2 To The Cathode Performance Of Proton Exchange Membrane Fuel Cell, Xiang-Li Hou, Hong-Feng Xu, Jian-Hua Dong, Xin Sun Feb 2006

Oxygen Enrichment Effect Of Ceo2 To The Cathode Performance Of Proton Exchange Membrane Fuel Cell, Xiang-Li Hou, Hong-Feng Xu, Jian-Hua Dong, Xin Sun

Journal of Electrochemistry

CeO2 was added to Pt/C catalyst in the cathode of PEMFC by both sol and impregnation methods.The samples were evaluated by TEM,cyclic voltammogram techniques and proton exchange membrane fuel cell performance test.The addition of CeO2 obviously improved the performance of PEMFC and represented a notable function of oxygen enrichment in the cathode side.But with the addition of CeO2,part of the catalyst surface was covered and led to the performance drop of the PEMFC.The best content of CeO2 is 1% when it is added by impregnation method and 3% when it is added by sol method.

Go to article

The Deactivation Mechanism Of Metal Oxide Anodes Under Alternative Current Electrolysis Condition, Jun-Tao Wang, Yan Han, Guang-Zhang Chen, Wen-Fa Liu Nov 2005

The Deactivation Mechanism Of Metal Oxide Anodes Under Alternative Current Electrolysis Condition, Jun-Tao Wang, Yan Han, Guang-Zhang Chen, Wen-Fa Liu

Journal of Electrochemistry

The metal oxide anodes coated on titanium used in seawater electrolysis were prepared by thermal decomposition. Their morphologies, compositions and phase structures were determined by scanning electron microscope(SEM), energy dispersive X-ray detector(EDX) and X-ray diffraction(XRD). The electrochemical properties of the anodes were characterized by accelerated life test, cyclic voltammetry and electrochemical impedance spectroscopy. SEM, EDX and XRD showed that solid solution structures of (Ru, Ir, Ti)O2 and (Ir, Ti)O2 were formed after pyrolysis, the solid solution structures and active components were disappeared after the deactivation of the anodes. Electrochemical results indicated that the active area decreased and the …

Go to article

The Electrocatalystic Investigation Of 3,4-Dihydroxybenzoic Acid On The Modified Multiply Wall Carbon Nanotubes, Ming-Qi Li, Duo-Chang Cai, Xiao-Ying He Nov 2005

The Electrocatalystic Investigation Of 3,4-Dihydroxybenzoic Acid On The Modified Multiply Wall Carbon Nanotubes, Ming-Qi Li, Duo-Chang Cai, Xiao-Ying He

Journal of Electrochemistry

The electrochemical behavior of 3,4-Dihydroxybenzoic acid(DHBA) on modified multiply wall carbon nanotubes electrode was investigated by cyclic voltammetry(CV) and square wave voltammetry(SWV). Results show that in 0.1 mol/L HCl solutions the modified carbon nanotube electrode has an obvious electrocatalytic effect on the oxidation and deoxidization of DHBA. The oxidation current of DHBA is linear to it's concentration in the range of 4.0×10-6～1.0×10-4 mol/L and 2.0×10-4～8.0×10-4 1mol/L with correlation coefficient of 0.9995 and 0.9992. The detection limit is 1.0×10-6 mol/L.

Go to article

Solid Oxide Fuel Cells-Materials And Prospects, Molenda Janina, Marzec Jacek Nov 2005

Solid Oxide Fuel Cells-Materials And Prospects, Molenda Janina, Marzec Jacek

Journal of Electrochemistry

The paper summarizes and discusses the basic properties of solid oxide fuel cell (SOFC) components (electrode materials and electrolyte) from the point of view of their essential functional parameters suck as chemicalstability, transport, catalytic and thermomechanical properties under operational conditions in a SOFC. An interrela-tion between the defect structure of these materials related to oxygen nonstoichiometry and their electronic propertiesand catalytic activity was shown. Single-chamber fuel cell concept was also presented.

Go to article

A Continuous Operation For Electroreduction Of Oxalic Acid To Glyoxylic Acid, Xiao-Hui Hu, Xiang-Fei Yan, Yu-Zhong Su, Jun Li, Qing-Biao Li Nov 2005

A Continuous Operation For Electroreduction Of Oxalic Acid To Glyoxylic Acid, Xiao-Hui Hu, Xiang-Fei Yan, Yu-Zhong Su, Jun Li, Qing-Biao Li

Journal of Electrochemistry

A simulative-continuous-operation approach was proposed to study the continuous operation for electroreduction of oxalic acid to gloxylic acid using a packed bed reactor and a parallel reactor with cooled cathode in order to solve the low productivity problem in current state by using traditional reactor. The effects of the concentration of oxalic acid and temperature on this process were also studied. Results showed that,after 30min of the reaction(residence time), the mass fraction of the produced glyoxylic acid in the catholic solution could reach 3.76% and 3.66% with respect to a saturated oxalic acid method and a step-temperature decreasing method. From …

Go to article

Electrochemical Oxidation Of Organic Additives In Tin Plating Electrolytes, Yin-Mei Cheng, Lan-Kun Cai, Qiang Song Nov 2005

Electrochemical Oxidation Of Organic Additives In Tin Plating Electrolytes, Yin-Mei Cheng, Lan-Kun Cai, Qiang Song

Journal of Electrochemistry

Cyclic voltammetry(CV) was used to characterize the voltammetric behaviours of organic additives, e.g. PSA(phenolsulfonic acid) EN(ethoxylatedα-naphthol) and ENSA(ethoxylatedα-naphthol sulfonic acid), on the anode surface. In PSA solutions, an anodic peak was obtained and the peak potential was about 1.2V. In EN and ENSA solutions, two anodic peaks were obtained and the peak potentials were about(0.95V) and 1.3V. The products of galvanostatic electrolysis were separated by HPLC(high performance liquid chromatography) and analyzed by EI/MS(electron ionizing mass spectrometry). The mechnism of the electrochemical oxidation was also disussed.

Go to article

Nafion Emulsion Method For Fuel Cell Membrane-Electrode-Assembly Preparation, Chao-Yang Xia, Lin Zhuang, Jun-Tao Lu Aug 2005

Nafion Emulsion Method For Fuel Cell Membrane-Electrode-Assembly Preparation, Chao-Yang Xia, Lin Zhuang, Jun-Tao Lu

Journal of Electrochemistry

A Nafion emulsion method for fuel cell membrane-electrode-assembly (MEA) preparation was reported for the first time in this paper. 5 %(by mass) Nafion alcohol solution and non-polar solvent (e.g., cyclohexane) were ultrasonicallymixed to produce Nafion emulsion. The catalyst ink prepared using the thus-obtained Nafion emulsion can be directly cast onto Nafion membrane to make MEA. This method is simple in operation, and effectively preventsthe Nafion membrane swelling, hence is suitable for large-scale application. The MEA thus-prepared showed comparable catalyst efficiencywith respect to the popular transfer-method, and the preliminary performance in room-temperature H2/O2 fuel cell test was satisfying.

Go to article

Electrocatalytic Oxidation And Degration Of Active Red X-3b By Nanotubes Catalytic Electrodes, Yi Wen, Jian-Hui Fang, Wei-Min Cao, Li-Yi Shi Aug 2005

Electrocatalytic Oxidation And Degration Of Active Red X-3b By Nanotubes Catalytic Electrodes, Yi Wen, Jian-Hui Fang, Wei-Min Cao, Li-Yi Shi

Journal of Electrochemistry

The catalytic splitting decomposition of carbon nanotubes isprocessed by dispersing with dilute nitric acid and thermal oxidation. Then well-proportionedphenolic resin is mixed in the carbon nanotubes. Then, the carbon nanotubesare made into electrodes by hot-press molding after the process of milling with high speed. The surface of the carbon nanotubes electrodes is analyzed by SEM. Active red X-3B simulated waster water is disposed by carbon nanotubes catalyticelectrode (anode) and stainless steel(cathode). The influencing factors of degradation by current density, concentrationof electrolyte, systemtemperature and pH are investigated. The experimental results indicated that acidiccondition is propitious tothe degradationreaction of organicdyestuff and wastewater …

Go to article

Effect Of Sintering Temperatures On Synthesis Of Mgco0.4Mn1.6O4 Positive Materials In Magnesium Ion Battery, Xiu-Ling Gao, Li-Fang Jiao, Hua-Tang Yuan, Jian-Sheng Cao, Ming Zhao, Hai-Xia Li, Yong-Mei Wang Aug 2005

Effect Of Sintering Temperatures On Synthesis Of Mgco0.4Mn1.6O4 Positive Materials In Magnesium Ion Battery, Xiu-Ling Gao, Li-Fang Jiao, Hua-Tang Yuan, Jian-Sheng Cao, Ming Zhao, Hai-Xia Li, Yong-Mei Wang

Journal of Electrochemistry

The cathode material MgCo0.4Mn1.6O4 for magnesium ion battery was synthesized by sol-gel method. The TG-DTA and XRD analyses showed that the prepared samples has simple spinel structure. Effect of annealing temperature on electrochemical properties was researched. The result shows that the sample sintered at 700℃ has the best electrochemical properties.

Go to article

Electrochemical Reduction Characteristics Of Nitrobenzene At The Copper Electrode, Jin-Hong Fan, Wen-Ying Xu, Ting-Yao Gao Aug 2005

Electrochemical Reduction Characteristics Of Nitrobenzene At The Copper Electrode, Jin-Hong Fan, Wen-Ying Xu, Ting-Yao Gao

Journal of Electrochemistry

The electrochemical reduction characteristics and transition steps of nitrobenzene aqueous solution at the copper electrode, as well as its reduction mechanism were extensively investigatedby using the techniques such as cyclic voltammetry (CV) and linear scan voltammetry (LSV). The results showed that the reduction peaks of nitrobenzene at the copper electrode were located at 0.58 V and 1.32 V or so (vs. SCE), both acidity and alkalinesolutionsfavoredthe reduction of nitrobenzene. The adsorption of compounds followed by the reduction process, which is controlled by the mass transfer step at higher nitrobenzene concentration. In addition, the higher anaerobic degree led to faster reduction …

Go to article

Application Of Nickel Foam Electrode For Electroreduction Intermediate Of Purine, Hui-Wen Yang, Xi-En Hu, Xue-Jun Wang May 2005

Application Of Nickel Foam Electrode For Electroreduction Intermediate Of Purine, Hui-Wen Yang, Xi-En Hu, Xue-Jun Wang

Journal of Electrochemistry

Nickel foam with weight uniformity, good porosity ,pore size and low resistivity as a three-dimensional cathode was used in a filter-press electrochemical reactor. The H2SO4 as supporting electrolyte, separator of cation ion exchange membrane, and the lead plate as an anode were used. The cyclic system consisted of electroreduction reactor, pump, store tank and ampere meter. NAU was electroreduced in the cathode chamber of the reactor. Purine intermediate was synthesized with DAU, and the results were compared with those of iron powder reduction process. A peak current in the electroreduction process was detected. The current density of …

Go to article

The Preparation And Performance Of The Aqueous Matrix For Molten Carbonate Fuel Cells, Hua-Xin Lin, Mo-Jie Ceng, Bao-Lian Yi May 2005

The Preparation And Performance Of The Aqueous Matrix For Molten Carbonate Fuel Cells, Hua-Xin Lin, Mo-Jie Ceng, Bao-Lian Yi

Journal of Electrochemistry

PVA matrix of MCFC was prepared from the α-LiAlO2 powder, and polyvinylalcohol(PVA), Compared with the conventional PVB matrix, higher porosity, higher thermal weight loss and smaller maximum pore diameter were achieved for PVA matrix. Single cell was assembled with PVA matrix. At reaction gas pressure of 0.9 MPa, under reaction gas utilization of 20%, at 300 and 428.57 mA·cm-2, the cell voltage was 0.849 and 0.739 V respectively, and the output power density was 254.7 and 316.7 mW·cm-2 respectively, which are higher than those of the cell assembled with PVB matrix. During thermal cycles, the cell …

Go to article

The Synthesis, Characteristics And Performance Of Cnt Composites As Anodic Materials In Litium-Ion Battery, Quan-Feng Dong, Ming-Sen Zheng, Zhen-Cai Huang, Ming-Gang Jin, Ya-Ding Zhan, Zu-Geng Lin May 2005

The Synthesis, Characteristics And Performance Of Cnt Composites As Anodic Materials In Litium-Ion Battery, Quan-Feng Dong, Ming-Sen Zheng, Zhen-Cai Huang, Ming-Gang Jin, Ya-Ding Zhan, Zu-Geng Lin

Journal of Electrochemistry

As an anodic material for lithium ion battery the carbon nano-tube (CNT) and some compounds based on tin have ever been investigated intensively. The fruited progress has not been made yet, however. In this paper the composites of CNT and Sn/SnO2 were synthesized employing two methods and characterized by SEM and XRD. And the electrochemical performance of the composites was investigated.

Go to article

Investigation On Ru-Ti-Ir-Sn Oxide Anode Coatings For Electrolyzing Seawater, Ke Wang, Yan Han, Lei-Yuan Wang, Xiao-Ling Zhang, Yu-Pu Sun May 2005

Investigation On Ru-Ti-Ir-Sn Oxide Anode Coatings For Electrolyzing Seawater, Ke Wang, Yan Han, Lei-Yuan Wang, Xiao-Ling Zhang, Yu-Pu Sun

Journal of Electrochemistry

The anode coatings of Ru-Ti-Ir-Sn oxide with various compositions were prepared by thermal decomposition. The physical and electrochemical properties of the coatings were characterized by scanning electron microscope (SEM), energy dispersive X-ray detector (EDX), accelerated life, current efficiency, anti-Mn2+ contamination, polarization curveandcyclic voltammetry tests. The results showed thatthe anode coating with optimized formula possessed excellent overall properties for electrolyzing seawater.

Go to article

Study On Synthesis Of M-Phenoxy Benzoic Acid By Electrolysis Oxidation Method, Wei Xu, Chong-Tao Zhao May 2005

Study On Synthesis Of M-Phenoxy Benzoic Acid By Electrolysis Oxidation Method, Wei Xu, Chong-Tao Zhao

Journal of Electrochemistry

The m-phenoxy benzoic acid was synthesized by oxidation m-phenoxy toluene using Cr(Ⅵ)as oxidation media, which was prepared by electrolysis oxidation of Cr(Ⅲ)in the electrochemical bath using Nafion 417 as a diaphragm, Pb-PbO2 as an anode and Pb as cathode. The effect factors on the electrochemical oxidation of Cr(Ⅲ)to Cr(Ⅵ)in this electrolysis were studied. Furthermore, the optimal conditions for electronic synthesis of m-phenoxy benzoic acid were also discussed.

Go to article

The Effect Of Oxidant On Structure And Properties Of Pan/Ptfe Conducting Composite Membrane, Chang-Yuan Tao, Jing Chen, Jun Du, Cai-Xin Sun May 2005

The Effect Of Oxidant On Structure And Properties Of Pan/Ptfe Conducting Composite Membrane, Chang-Yuan Tao, Jing Chen, Jun Du, Cai-Xin Sun

Journal of Electrochemistry

The PAn/PTFE conducting composite membrane was prepared by means of in-situ permeating chemical polymerization, with (NH4)2S2O8 and Na3VO4 being used as an oxidant respectively. The polymerization-growth behavior of the aniline by using different oxidant was compared. In addition, the oxidant effect on the structure and properties of conducting composite membrane was discussed. The results of SEM micrographs, pore size distribution and electrochemical methods suggested that using either oxidants could also induce the product with small pore size and dense pore structure. Compared with (NH4)2S2O …

Go to article

Fundamental Chemistry Of U And Pu In The Tbp-Dodecane-Nitric Acid System: Quaterly Report January - March, 2005, Kenneth Czerwinski, Cynthia-May Gong, Amber Wright Mar 2005

Fundamental Chemistry Of U And Pu In The Tbp-Dodecane-Nitric Acid System: Quaterly Report January - March, 2005, Kenneth Czerwinski, Cynthia-May Gong, Amber Wright

Separations Campaign (TRP)

The speciation of hexavalent U and tetravalent Pu will be examined in the TBP-dodecane-nitric acid systems. This topic is chosen based on data needs for separation modeling identified by the AFCI. Emphasis will be placed on studying the influence of nitrate and acetohydroxamic acid on U and Pu speciation as well as conditions where a third phase forms in the organic phase. The organic phase will be 30% TBP in dodecane. Equal volumes of aqueous and organic phase will be used. The speciation of the actinides in the aqueous and organic phase will be determined by a number of different …

Go to article

Influence Of Rare Earth Oxide On The Performance Of Secondary Zinc Electrodes, Xian-Ling Meng, Hua-Bin Yang, Jun-Hong Wang, Zuo-Xiang Zhou Feb 2005

Influence Of Rare Earth Oxide On The Performance Of Secondary Zinc Electrodes, Xian-Ling Meng, Hua-Bin Yang, Jun-Hong Wang, Zuo-Xiang Zhou

Journal of Electrochemistry

Influence of La(OH)3 or Ce(OH)3 in secondary zinc electrode was investigated by the cyclic voltammetry, potentiodynamic polarizationand potentiostatic polarization tests and influence of La2O3 or CeO2 in the charge/discharge performance of Zn/Ni battery was studied by galvanostatic charge/discharge experiment. The results showed that the film of rare earth hydroxide prevented the zincate species from transferring toward solution, enhanced hydrogen overpotential and decreased thecorrosion current density (icorr), and therefore inhibited zinc corrosion. The potentiostatic polarization results at100mV overpotential showed that La(OH)3 or Ce(OH)3 oated on the zinc electrode effectively suppressed the …

Go to article

Research On Phenol Wastewater Treatment By Electrochemical Oxidation, Tian-Cheng Li, Shen-Lin Zhu Feb 2005

Research On Phenol Wastewater Treatment By Electrochemical Oxidation, Tian-Cheng Li, Shen-Lin Zhu

Journal of Electrochemistry

Electrochemical oxidation is an effective technology for the phenol wastewater treatment, and the anode properties are important to the electrochemical oxidationefficiency. The over-potentials of oxygen evolution have been measured for thestainless steel, feasible graphite and SnO2/Ti anode respectively. Moreover, the synthetic phenol wastewater was treated by the electrochemical oxidation with the stainless steel or feasible graphite anodes. The experimental results showed that the order of the over-potential is SnO2/Ti > graphite > stainless steel; meanwhile, the COD values of purified water were approaching to or less than 100 mg·L-1, and the phenol concentrations in the purified …

Go to article

Fundamental Chemistry Of U And Pu In The Tbp-Dodecane-Nitric Acid System: Quarterly Report, Kenneth Czerwinski, Cynthia-May Gong, Amber Wright Jan 2005

Fundamental Chemistry Of U And Pu In The Tbp-Dodecane-Nitric Acid System: Quarterly Report, Kenneth Czerwinski, Cynthia-May Gong, Amber Wright

Separations Campaign (TRP)

The speciation of hexavalent U and tetravalent Pu will be examined in the TBPdodecane- nitric acid systems. This topic is chosen based on data needs for separation modeling identified by the AFCI. Emphasis will be placed on studying the influence of nitrate and acetohydroxamic acid on U and Pu speciation as well as conditions where a third phase forms in the organic phase. The organic phase will be 30 % TBP in dodecane. Equal volumes of aqueous and organic phase will be used. The speciation of the actinides in the aqueous and organic phase will be determined by a number …

Go to article

Preparation And Photo-Catalyst Properties Of The α-Fe2O3-Tio2 Films On Sodium Alginate Polymer, Li-Qin Chen, Huai-Zhen Zhong, Ri-Yao Chen, Xi Zheng, Zhen Chen Nov 2004

Preparation And Photo-Catalyst Properties Of The α-Fe2O3-Tio2 Films On Sodium Alginate Polymer, Li-Qin Chen, Huai-Zhen Zhong, Ri-Yao Chen, Xi Zheng, Zhen Chen

Journal of Electrochemistry

Three new nano thin films of α-Fe2O3, TiO2 and α-Fe2O3-TiO2 by doping their powder with sodium alginate polymer were prepared. Surface structure and catalytic activities of the films were characterized by FTIR, XRD, PL, TEM and I-V techniques. The results of UV-visible absorption showed that the methylene blue was mineralized in aqueous of α-Fe2O3/SA, TiO2/SA and (α-(Fe2O3))-TiO2 /SA upon radiation with ultra violet light. α-Fe2O3 enhanced their photo-decolorized-activities by doping 15% TiO2.

Go to article

Electrochemical Behaviours Of Hemoglobin-Ddab-Modified Powder Microelectrode And The Application Of The Powder Microelectrode In Determination Of Nitric Oxide, Zhi-Mou Guo, Huan Liu, Jian Chen, Wen-Ting Zhang Nov 2004

Electrochemical Behaviours Of Hemoglobin-Ddab-Modified Powder Microelectrode And The Application Of The Powder Microelectrode In Determination Of Nitric Oxide, Zhi-Mou Guo, Huan Liu, Jian Chen, Wen-Ting Zhang

Journal of Electrochemistry

The electrochemical behaviours of DDAB-Hb-PME were studied in this paper. The (apparent) surface concentration of Hb was enhanced greatly by using the powder microelectrode (technique). NO reacts with Hb and absorbs on the surface of the modified carbon powder. Therefore, the output of the electrode was enhanced greatly by employing PME with higher reaction surface (area). The sensitivity of DDAB-Hb-PME is 3.1 mA/μmol·L-1·cm2, which is much larger than the values obtained with the traditional electrodes. The detection limit is 9 nmol·L-1 and the linear response range is 9～100 nmol·L-1.

Go to article

Anodic Dissolution Of Aluminum In Koh-Ethanol Solutions, Hai-Bo Shao, Jian-Ming Wang, Xiao-Yan Wang, Yi Zheng, Jian-Qing Zhang Nov 2004

Anodic Dissolution Of Aluminum In Koh-Ethanol Solutions, Hai-Bo Shao, Jian-Ming Wang, Xiao-Yan Wang, Yi Zheng, Jian-Qing Zhang

Journal of Electrochemistry

The feasibility of employing aluminum in KOH ethanol solution as a battery anode system was discussed. Weight loss measurement showed that the corrosion rate of Al is low enough to be used in sealed batteries. Through the measurements done by anodic polarization, EIS and galvanostatic discharge, it was found that Al is electrochemical active in a wide potential range in this system, and its discharge mechanism is similar to that of Al in aqueous solution. The discharge potential increased rapidly after a period of time, which might be caused by the discharge products depositing on the electrode surface.

Go to article

Electrocatalytic Performances Of Carbon Nanotube Air Electrode For Oxygen Reduction, Feng-Ming Zhao, Chun-An Ma Nov 2004

Electrocatalytic Performances Of Carbon Nanotube Air Electrode For Oxygen Reduction, Feng-Ming Zhao, Chun-An Ma

Journal of Electrochemistry

The air electrodes with different mass ratio of Pt/active carbon or carbon nanotube as catalyst layer material have been prepared. The electrocatalytic performances for oxygen reduction were evaluated by means of polarization curve and electrochemical impedance spectroscopy (EIS). The results disclosed that carbon nanotubes dealt with nitric acid in the catalyst layer had been improved obviously on the electrocatalytic activity. After the surface of carbon nanotube was oxygenated and aggraded with platinum, the catalyst had obviously effects on the electrocatalytic activity. The air electrode with the mass ratio of active carbon to Pt/carbon nanotube in 4∶1 showed better electrocatalytic activity, …

Go to article

Effect Of Fe3+ Dopen Of Titanium Dioxide Film On Absorption Spectra And Photo Catalysis, Mei-Qun Xiao, Jia-Nian Shen, Moucheng Li, Peng-Fei Wu, Dong Liu, Yu-Juan Zhang Nov 2004

Effect Of Fe3+ Dopen Of Titanium Dioxide Film On Absorption Spectra And Photo Catalysis, Mei-Qun Xiao, Jia-Nian Shen, Moucheng Li, Peng-Fei Wu, Dong Liu, Yu-Juan Zhang

Journal of Electrochemistry

Photo-catalytic titanium dioxide film in nano crystalline has been prepared by electrochemical oxidation process and adding different amount of ferric ion into the electrolyte during the anodic oxidation.The effects of Fe3+ dopen on absorption spectra and photo-catalytic of the titanium dioxide films have been studied. It shows that the Fe3+ dopen caused the red shife of the absorption edge for the incoming light and exhibited the improved photocatalytic reactivity.

Go to article

Lithium Insertion Into Tio2(B) Nanobelts Synthesized By The "Soft Chemical" Method, Cha-Geng Nie, Zheng-Liang Gong, Lan Sun, Juan Zuo, Yue-Kun Lai, Chang-Jian Lin Aug 2004

Lithium Insertion Into Tio2(B) Nanobelts Synthesized By The "Soft Chemical" Method, Cha-Geng Nie, Zheng-Liang Gong, Lan Sun, Juan Zuo, Yue-Kun Lai, Chang-Jian Lin

Journal of Electrochemistry

TiO2(B) Nanobelts were synthesized by using the "Soft chemical"method. The products were characterized by means of transmission electron microscope(TEM), X-ray diffraction(XRD), Raman spectrum and energy dispersive spectrum(EDS). Galvanostatic charging and discharging tests showed that lithium-ion intercalation/deintercalation occurred reversibly in the TiO2(B) nanobelts electrode, and a high capacity (265 mAh·g-1) can be obtained. The results suggested that TiO2(B) Nanobelts might be a promising negative electrode material of second Lithium battery.

Go to article

First Prev Next Last