Materials Chemistry Commons^™

Synthesis Of Polyunit Vapor Phase Inhibitor And Its Volatile Corrosion Inhibition Performance, Da-Quan Zhang, Li-Xin Gao, Guo-Ding Zhou

Journal of Electrochemistry

A Mannich Base derivative (BMMCH), containing two morpholinum moieties and one cyclohexylamnonium moiety, was synthesized through aminomethy1 reaction. Its configuration was verified by IR and ¹H-NMR. Its volatile rustproofing effect was appraised by volatile rustproofing sieve test and vapor inhabitability test. The result shows that BMMCH has good protection effect for carbon steel. BMMCH has lower volatility compared with dicyclohexylamnonium nitrite (DICHAN) via closed space volatile weight-loss test. The inhibition mechanism was studied by potentiodynamic polarization electrochemistry technique in ASTM simulated atmospheric water. The corrosion potential of carbon steel electrode shifted to a negative direction when BMMCH was joined …

The Technique Of Rare-Earth Conversion Coatings On Aluminum Alloy, Jun-Tao Wang, Jian-Hua Wu, Guang-Zhang Chen

Journal of Electrochemistry

The orthogonal design was used to screen the film_forming technique on LY12 aluminum alloy using quadrivalent cerium salt, and the corrosion-resistance performance of the coating was studied. The results revealed that: after LY12 aluminum alloy was treated by cerium salt, its pitting potential shifts to positive direction while the corrosion potential slightly decreases, showing that the alloy becomes less sensitive to pitting corrosion was greatly improved, comparable to that after chromate treatment; in addition, by combining the results of electrochemical measurements with surface analysis, the mechanism of corrosion-resistance on the race-earth conversion coating of the aluminum alloy was also discussed.

An Electrochemical Prediction Method For Caustic Scc Of Fe-Cr-Ni Alloy, Chun-Bo Huang, Zhan-Peng Lv, Wu Yang

Journal of Electrochemistry

Stress corrosion cracking (SCC) of Fe-Cr-Ni alloy (alloy 800 M) in hot concentrated caustic solution was investigated by means of tests of C-rings under controlled potentials. The steady dissolution current densities (i_st) of the plate specimens and C-rings polarized potentiostatically were measured. The simplifed steady potentiostatical curves were drawn on the basis of i_st. The ratio R_PD measured from i_st and steady passive current density i p at low potentials (R_PD = i_st/i_p) was designed as a polarization dissolution susceptibility parameter. The parameter R_PD values of both plate …

Corrosion Fatigue And Dynamic Strain Aging Of Duplex Stainless Steel In Aqueous Solution, Chuan-Ming Tseng, I-Hsuang Lo, Wen-Ta Tsai

Journal of Electrochemistry

The corrosion fatigue and dynamic strain aging behaviors of 22%Cr duplex stainless steel (DSS) in sodium chloride solutions were investigated. Austenitic 316L SS and ferrtic 430 SS were also used in this study for a comparison. The experimental results showed that no stress corrosion cracking (SCC) occurred in all these SSs tested in 3.5wt% NaCl solution at 80 ℃. However, dynamic strain aging (DSA) occurred in 316L austenitic SS and 22%Cr DSS during slow strain rate testing (SSRT) in this solution.The occurrence of DSA was dependent on solution temperature,strain rate and the presence of austenitic phase. The corrosion rate of …

Comparison Of Thermal Cyclic Oxidation Of The Pvd Ni-Al And Hvof-Mcraly Coatings, J-T Chang, C-H Yeh, J-L He, K-C Chen

Journal of Electrochemistry

A PVD process-cathodic arc plasma ion plating was used to deposit Ni-Al films on Inconel 600 superalloy. The oxidation behaviors of PVD Ni-Al coating and the thermal sprayed CoCrAlY coatings were revealed and compared by performing cyclic thermal oxidation test at 1100 ℃ to evaluate its feasibility. Experimental results showed that the films with different compositions of Ni₆₂Al₃₈, Ni₆₃Al₃₇ and Ni₆₉Al₃₁ could be obtained when using Ni₅₂Al₄₈, Ni₆₀Al₄₀ and Ni₇₀Al₃₀ as targets, respectively. During the cyclic thermal oxidation test, the …

Fabrication Of Scanning Micro Cl- Probe And In Situ Imaging Of Cl- At The Interface Of 2024 Al Aloy/Solution, Yu-Hua Lin, Min-Hua Shao, Rong-Gang Hu, Yan Li, Rong-Gui Du, Chang-Jian Lin

Journal of Electrochemistry

Micro combination Ag/AgCl electrode with a tip measuring tens micron in diameter was fabricated. The probe satisfied in situ imaging of Cl^- distribution at metal surface in chloride solution because of its excellent linearity between potential and Cl- concentration, rapid response, good stability and selectivity. With the aid of the home made Micro Electrode Scanning system and scanning Cl^- probe, the effect of the [Cl^-] at 2024-Al/solution interface on localized corrosion process was investigated. It was demonstated directly that Cl^- ion in solution immigrated toward, then adsorbed preferentially and accumulated at the junction between the …

Effect Of Heat Laminating Aggregation Status Of Polymer Lithium-Ion Battery Cathode On Battery Performance, Ming-Gang Jin, Quan-Feng Dong, Ming-Sen Zheng, Li Huang, Hui-Qun Cai, Jin-Qua You, Zu-Geng Lin

Journal of Electrochemistry

Multi-layer heat laminated polymer lithium ion battery was made, the effect of temperature of cathode laminating on battry performance was also investigated. It was discovered that suitable temperature of cathode laminating is critical to battery performance and is a key parameter to manufacture process control of polymer lithium ion battery.

Electrochemistry And Electrocatalysis Of A Novel Μ-Oxamido Copper(Ⅱ) Binuclear Complex, Gui-Lian Gao, Guo-Bao Li, Qiu-Xia Yang, Xue-Lin Wang

Journal of Electrochemistry

In this paper, the cyclic voltammetric and spectroelectrochemical behaviors of μ-oxamido Copper(Ⅱ) Binuclear Complex (deCu) in PBS were studied. Cyclic voltammograms of this complex in PBS (pH=9) exhibited two reductive peaks (E_pc1 =-0.25 V, E_pc2 = -0.50 V) at hanging mercury drop electrode(HMDE), peaks at -0.50 V and -0.25 V corresponded to the reduction of ligand and copper(Ⅱ) complex, respectively. The spectroelectrochimical experiments showed that there was a new absorption band at 440 nm, and the absorption peaks at 270 nm, 280 nm red shifted to 300 nm, 310 nm under potential of -0.75 V. It was meant …

Influence Of Marine Organisms Upon Corrosion Of Steel Piling Systems, Jiunn-Shyong Luo, Cliff Rau, Kuei-Ching Chen

Journal of Electrochemistry

To study the influence of marine organisms upon corrosion of ASTM A36 steel piling sysems, specimens were immersed in both natural and synthetic seawater. Electrochemical techniques such as linear polarization resistance and electrochemical impedance scan(EIS) were applied to evaluate corrosion of the steel. The results indicated that attachment of marine organisms to form fouling layers on the steel surface reduced general corrosion, but localized corrosion occurred underneath marine organisms. An equivalent circuit model was established to simulate attachment of marine organisms upon carbon carbon steel surfaces.

Severe Corrosivity And Its Eletrochemical Mechanism Of Seawater In Xiamen Sea Area To Al-Mg Alloys, Le-Yun Lin, Yue-Hong Zhao

Journal of Electrochemistry

The surface layer seawater of different sea areas in China exhibit different corrosivity to Al-Mg alloys according to the experiment results of 16 years exposure in seawater. The seawater in Xiamen sea area possesses severe corrosivity while seawater in Qingdao possesses the mildest corrosivity to Al-Mg alloys with better regularity of corrosion behavior. The present paper illustrates by experiment data that the strongest corrosivity of Xiamen seawater to Al-Mg alloys is owing to the low salinity of the seawater and the “electrolyte effect” come from it. The 16 year corrosion data and corrosion morphology of the typical Al-Mg alloys from …

Discussion On Factors Of Unstable 304 Stainless Steel Stress Corrosion Cracking, Xin-Sheng Zhang, Chun-Chun Xu, Gang Hu

Journal of Electrochemistry

The 304 stainless steels were stretched at low temperatures to get different martensite phase transformation. Ferrmagnetometer was used to measure the martensite phase content. It was found that the dislocation density of 304 stainless sted was increased unavoidably with increase of deformation. Transmission electron microscope (TEM) was used to study the distribution of the dislocation. The influence of microstructure change on SCC of 304 stainless steel was discussed by slow strain rate testing (SSRT) in 42% MgCl₂ boiling solution,metallurgical microscope and scanning electron microscope (SEM).The results showed that martensite phase and dislocation flaw act together on the SCC susceptibility …

The Electroless Plating Ni-Fe-P Alloy And Its Voltammetric Behavior, Sen-Lin Wang, Hui-Huang Wu

Journal of Electrochemistry

Electroless Ni-Fe-P alloy deposition from an alkaline bath, containing sodium hypophosphite as reducer, boric acid as buffer agent and sodium citrate as complexing agent, was investigated. To increase the plating rate and to inprove the bath stability, the deposition parameters were optimized. The effects of process parameters (pH, temperature and mole ratio of [Fe²⁺]/([Ni²⁺]+[Fe²⁺]) on the plating rate and deposit composition were examined and it was found that the presence of ferrous sulfate in the bath has an inhibitory effect on the alloy deposition. As a consequence, the percentage of iron in the electroless …

The Mechanism Of Electrocatalytic Reduction Of Oxygen On Manganese Dioxide, Yu-Liang Cao, Han-Xi Yang, Xin-Ping Ai, Li-Fen Xiao

Journal of Electrochemistry

The oxygen electroreduction on the MnO₂ electrode was investigated by analysis of the polarzation properties of oxygen reduciton and its dependence on MnO₂ discharge state, in combination with the characterization of discharge intermediate and the kinetic parameters of the oxygen reduction. Based on the experimental observation and mechanistic analysis, it was suggested that the reduction of oxygen was closely related to the discharge behaviors of MnO₂. When MnO₂ was electrochimically reduced to MnOOH, it was immediately oxidized by oxygen molecules. Thus the oxygen reduction proceeds through continuous oxidation of the discharge product of MnO_{2 …}

Modeling Corrosion In Oxygen Controlled Lbe Systems With Coupling Of Chemical Kinetics And Hydrodynamics - Phase Three, Samir Moujaes, Yitung Chen

Transmutation Sciences Materials (TRP)

The proposed work will combine chemical kinetics and hydrodynamics in target and test-loop lead-bismuth eutectic (LBE) systems to model system corrosion effects. This approach will result in a predicative tool that can be validated with corrosion test data, used to systematically design tests and interpret the results, and provide guidance for optimization in LBE system designs. The task includes two subtasks. The first subtask is to try to develop the necessary predictive tools to be able to predict the levels of oxygen and corrosion products close to the boundary layer through the use of Computational Fluid Dynamics (CFD) modeling. The …

Environment-Induced Degradation And Crack-Growth Studies Of Candidate Target Materials: Annual Progress Report (May 2002 – May 2003), Ajit K. Roy, Brendan O'Toole

Transmutation Sciences Materials (TRP)

As indicated in the original proposal, the primary objective of this task is to evaluate the effect of hydrogen on environment-assisted cracking of candidate target materials for applications in spallationneutron- target (SNT) systems such as accelerator production of tritium (APT) and accelerator transmutation of waste (ATW). The materials selected for evaluation and characterization are martensitic stainless steels including Alloy HT-9, Alloy EP 823 and Type 422 stainless steel. The susceptibility to stress corrosion cracking (SCC) and hydrogen embrittlement (HE) of these materials are being evaluated in aqueous environments of interest using tensile specimens under constant load and slow-strain-rate (SSR) conditions. …

Quarterly Report For The Trp Project, March–June 2003, Samir Moujaes, Yitung Chen, Kanthi Kiran Daiska, Chao Wu

Transmutation Sciences Materials (TRP)

The MTL is assumed to be a 5m long rectangular loop with a circular cross-section. Because of the non-symmetry, and due to the active participation of the secondary flows due to the elbows present in the rectangular loop model, the geometry is considered as a 3D model.

When the regions of maximum corrosion and precipitation are compared, they fall in the same zone for both the analytical and simulated models. The reason for a larger concentration flux in the case of turbulent flow than for the laminar flow can be explained by the concept of higher lateral diffusion in the …

Study Of Marine Biocorrosion Using Afm And Molecular Techniques, Herbert H.P.Fang, Lichong Xu, Tong Zhang

Journal of Electrochemistry

Biofilm is ubiquitous in nature.However,corrosin caused by biofilm is still by and large overlooked. This presentation is to demonstrate the applications of several newly developed analytical techniques in chemisrty and microbiology for the study of marine biocorrosion on steel. AFM(atomic force microscopy) was applied to investigate the initial formation mechanism of biofilm and the degree of corrosion of steel in polluted seawater. DNA/RNA-related molecular techniques were used to analyze the microbial composition corrosive biofilm. Results showed that microbial corrosion began within six days, and the corroded volume in the increased as a power function of time with an index 2.83. …

A Bilayer Self-Assembled Membrane Electrode For Fluorescence And Its Electrochemical Characterization, Xiang-Ying Sun, Bin Liu, Yun-Bao Jiang

Journal of Electrochemistry

The bilayer membrane was assemblied on Au electrode by the electrostatic interaction between the fluorescence regent 1-naphthylamine diacetate acid (NADA) and DL-Cysteine. The SAMs electrode NADA/Cys/Au can be used as fluorescence and electrochemical sensor for metal ions. This paper states the electrochemical characterization of NADA/Cys/Au and SAMs' application in continous determination for Cu²⁺ and Ni²⁺.

The Electrochemical Behaviors Of A Novel Ferrocene Alkylthiol Sams On Au Electrode, Xiao-Gang Zhang, Yan-Li Shi, Hu-Lin Li

Journal of Electrochemistry

A novel alkylthiol molecule containing ferrocene and pyridium moieties and its hydrogenated products were synthesized and subsequently assembled on Au electrode as SAMs. Cyclic voltammogram(CV) was used to investigate the structure-dependent electrochemical response of the SAMs in 0.1 mol/L HClO₄ aqueous solution.

Initial Stages Of Pd Deposition Onto Au(111) Electrodes From Pdso4, Jing Tang, Petri M., Kibler L.A., Kolb D.M.

Journal of Electrochemistry

Metal thin films have attracted considerable interest in relation to catalysis, energy, material, corrosion and environmental protection. Pd thin film is capable of proton reduction and strong hydrogen absorption, which has shown electrocatalytic activity to the oxidation of small organic molecules. In this paper, in-situ STM measurements are performed to study the deposition process and the influence of the surface structure and anion adsorption. When Pd is deposited from PdSO₄ solution on Au(111) in the UPD range, a monolayer of Pd with pseudomorphic (1×1) structure was formed on the substrate with induced (3×7) R19° SO₄^2- adsorption. With …

Recent Progress In The Research On Electrodeposition Of Composite Coatings, Xiao-Bing Liu, Xu-Cheng Wang, Yu Chen, Dan-Hong Cheng, Zu-Zhan Yu

Journal of Electrochemistry

Recent progress in the research on composite coatings prepared by electroplating technology is reviewed. The nanoscaled particles, electrocatalytic, photoactive composite coatings are emphatically discussed. The composite coatings prepared by dispersing nanoscaled particles could attain better hardness, wear resistance and corrosion resistance than those of composite coatings which prepared by adding micronscaled particles. As compared with pure metal electrode and alloy electrode, some electrocatalytic composite coatings electrode could markedly reduce the overvoltages of cathodic and anodic electrode reaction. In recent years, the electrocatalytic composite coatings which based on metal oxides and conductive polymer as matrix materials become a newest field of …

Preparation And Electrochemical Preformance Of Zn-La Alloys, Xian-Ling Meng, Hua-Bin Yang, En-Dong Yang, Xiao-Dan Wang, Hai-Chang Zhang, Jun-Hong Wang, Zuo-Xiang Zhou

Journal of Electrochemistry

Zn-La alloys were prepared by solid phase diffusion method and the effects of La on the electrochemical performance of zinc electrodes were investigated using potentiostatic polarization technique and charging/discharging cycle test. The results showed that adding La to zinc electrode remarkably suppressed the zinc dendrite, the shape of zinc electrode and zinc corrosion, and hence, markedly improved the cycle performance of zinc electrodes. The discharging capacity of the zinc electrode containing 0.5at.% La which was the optimum was still 520 mAh/g after it cycled 80s at the current of 100 mA. The XPS showed that La element mainly adhered on …

Microstructure And Electrochemical Characteristics Of The Anodic Film Formed On Aluminum Surface, Jeng-Kuei Chang, Chi-Min Liao, Chih-Hsiung Chen, Wen-Ta Tsai

Journal of Electrochemistry

The thickness, morphology, chemical composition, and crystallinity of the anodized film formed on aluminum were examined in a transmission electron microscope (TEM). Thin foil for TEM analysis was prepared by ultramicrotomy. The relationship between the microstructure and the electrochemical characteristics of the alumina film forming on the pure aluminum was discussed in this investigation. At the forming voltage less than 100V, the anodized films formed at 85 ℃in aqueous ammonium adipate electrolyte was amorphous in nature. Although the film resistance was increased with the forming voltage, its dielectric constant was not changed significantly. As the forming voltage exceeded 100V, crystalline …

Oxidation Behavior Of Zr-Cu-Al-Ni Amorphous Alloys In Air At 300～500℃, H. H. Hsieh, W. Kai, T. G. Neih, Y. Kawamura

Journal of Electrochemistry

The oxidation behavior of the Zr- based bulk amorphous alloy (BMG; Zr-30Cu-10Al-5Ni in at.%) was studied in dry air over the temperature range 300～500 ℃. The kinetic results indicated that the amorphous alloy oxidized linearly at 300 ℃, while the parabolic oxidation was observed at 350～425 ℃, and the oxidation behavior at 500 ℃ was irregular and complicated. In general, the scales formed on the surface of the amorphous alloy were temperature-dependent, consisting of tetragonal-ZrO₂ at 300 ℃, and of mostly tetragonal-ZrO₂ as well as minor amounts of monoclinic-ZrO₂ and CuO at T ≥ 350 ℃.

Selective Corrosion In Duplex Stainless Steel, Wen-Ta Tsai, Kuen-Ming Tsai, Chang-Jian Lin, Yan Fu

Journal of Electrochemistry

In duplex stainless steel, the two constituent phases, namely ferritic (α) and austenitic (γ) phases, have different crystal structure and chemical composition. They may thus exhibit different corrosion resistances in aqueous environment. In this investigation, an electrochemical technique with spatial resolution was employed to measure the potential difference between these two constituent phases in 2205 duplex stainless steel. Image analyzing techniques were also used to examine the preferential corrosion between α and γ phases. The experimental results showed that ferrite had a higher potential than austenite in 0.01 mol/L NaCl solution. In 2 mol/L H₂SO₄+x mol/L …

Electrochemical Monitoring On The Deactivation Of A Metallic Oxide Anode, Li-Kun Xu, Shi-Zhe Song, Ting-Yong Wang, Guang-Zhang Chen

Journal of Electrochemistry

The process of accelerated life test of an IrO₂/Ta₂O₅ coated titanium anode was monitored using cyclic voltammetry and electrochemical impedance spectroscopy. The vatiation with electrolysis time of anodic voltammetric charge Q^*, the double layer capacitance C_dl,the oxide film resistance R_f and the charge transfer resistance R_ct for oxygen evolution was measured. A deactivation mechanism was proposed based on the observation results.

Corrosion Behavior Of Reinforcing Steel In Concrete Subjected To Chloride Contamination By Eis, Rong-Gang Hu, Rong-Gui Du, Chang-Jian Lin

Journal of Electrochemistry

Electrochemical impedance spectroscopy(EIS) was employed to study the influence of chloride on the corrosion behavior of reinforcing steel in concrete. In Nyquist plot, the spectrum consists of two semicircles, indicating that the reinforced concrete system contained two time constants,one derived from electrical double layer of reinforcing steel and the other from the deposition film of concrete layer. The depressed semicircle in lower frequency featured the non-faradic behavior of the electrical double layer (EDL) deviated from idea capacitor due to diffusive effect which was attributed to the surface roughness of rebar and the inhomogenity of concrete layer. Then the EDL was …

Corrosion Behavior Of Mg1.85Mm0.15Ni Hydrogen Storage Alloy Modified By Electroless Cu In Ch3Ohâ·H2O Solutions, Hua-Bin Yang, Hai-Chang Zhang, Hua Sun, Xiao-Dan Wang, Zuo-Xiang Zhou

Journal of Electrochemistry

The corrosion behavior of the Mg_1.85Mm_0.15Ni (Mm:Ce-rich mischmetal) alloy modified by electroless Cu coating in different CH₃OH-H₂O solutions has been investigated by potentiodynamic polarization and electrochemical impedance spectroscopy. These results showed that the corrosion behavior was improved after electroless Cu. The potentiodynamic polarization and electrochemical impedance spectroscopy results showed that the alloy electrode had more promising anti-corrosion behavior after coated in a 40%CH₃OH-H₂O solution. The values of corrosion current density and electrode reaction resistance were 5.6 mA·cm^-2 (11.7 mA·cm^-2 for uncoated alloy electrode) and 22.25 Ω·cm …

Synthesis And Electrochemical Characteristics Of Nickel-Based Complex Oxide LiANi0.78Co0.2Cd0.02O2, Rong-Zhong Yuan, Mei-Zhen Qu, Zuo-Long Yu

Journal of Electrochemistry

The nickel-based complex oxide Li_aNi_0.78Co_0.02O₂ cathode materials for lithium-ion rechargeable batteries was synthesized by the improved solid-state reaction method with LiOH·H₂O, ball-like Cd-doped Ni(OH)₂ and Co₂O₃ as raw materials. The analysis ICP-AES proved that the as-prepared compounds were near the stoichiometric form. The XRD, SEM and electrochemical characteristics testing were also carried out. The results showed that the complex cathode material Li_aNi_0.78Co_0.2Cd_0.02O₂ has layered structure, homogeneous surface distributions,uniform particles with good crystal morphology as well as stable electrochemical …

Perfluorinated Sulfonic Acid Lithium Conductivity Humidity Sensor, Hong-Feng Xu, Jing Liu, Li Wan

Journal of Electrochemistry

Treat carbon paper with 3% PTFE solution and dried in 340 ℃ for 40 minutes to enhance its intension, and level off the surface of the carbon paper with a mixture of XC-72 carbon black and PTFE solution. With those treated carbon paper as electrodes, recast Nafion thin film from 5% Nafion solution as humidity sensitive material, a solid polymer electrolyte humidity sensor was prepared on a thin PET film. Take the relative humidity data from several saturated salt solutions, the relationship between conductivity response and relative humidity was studied at different relative humidies .The results showed: when the polymer …