Chemistry Commons^™

A Study Of The Electroplated Fe-Cr-Ni Alloy Microstructure, Donglin Li, Jianping Liu, Fangzhou Guo, Jianrong Hua

Journal of Electrochemistry

The microstructure of the electroplated Fe-Cr-Ni alloys from the mixed carboxylic acid solution containing Cr(Ⅲ) and additives were determined with XRD and SEM. Experimental results showed that, under the experimental condition, the phase component, structure of Cu base electroplated Fe-Cr-Ni alloys had a critical thickness, which was 11 μm and a critical Ni content, which was 32%. Organic additives, formic acid or polyethylene Glycol, mainly affected the surface, cross section morphology of the electroplated Fe-Cr-Ni alloys. Adding Mo to the electroplated Fe-Cr-Ni alloys led to remarkable corrosion resistance in concentrated HCl.

Polarographic And Voltammetric Behaviour Of Complex Of Ciprofloxacin With Manganese, Jialing Zhang, Huizhi Fan, Jinghao Pan

Journal of Electrochemistry

In 0.1 mol·L^-1 NH₃NH₄Cl buffer solution (pH 9.2) ,a sensitive reduction peak of complex of ciprofloxacin (CPFX) with manganese (Mn) was obtained by single sweep oscillopolarograph. The peak potential (E_p) is -1.61 V (vs.SCE). The peak current (i_p) is proportional to the concentration of Mn(Ⅱ) over the range of 5×10^-6 ～2×10^-5 mol·L^-1. It is possible to be applied to the determination of Mn(Ⅱ). The polarographyic and voltammetric behaviour of complex was studied in detail. The ratio of CPFX∶Mn in the complex was 2:1. The electrode reaction mechanism …

Electrochemical Studies Of Zncl2 Urea Melts, Peng Liu, Qiqin Yang, Guankun Liu, Yexiang Tong

Journal of Electrochemistry

The electric conductivities of ZnCl₂ Urea melts were determined .The influences of temperature and concentration on the conductance have been studied. The cylic voltammetry, potentiostatic electrolysis and open circuit potential time curve after electrolysis, X-ray diffraction were used to investigate the electroreduction of Zn²⁺, electrodeposition of zinc on some electrodes in urea metal chlorides melt. The conductivity of urea-NaCl-ZnCl₂ melt can reach to over 30 ms·cm^-1 (125 ℃), and has a liner relationship with temperature from 108 to 140 ℃. The electroreduction of Zn²⁺ to zinc is reversible at one step, and CuZn_{5 …}

The Electroless Nickel For Aluminium Honeycomb Shielded Vent Windows, Ronghua Wang, Jiaqian Bu

Journal of Electrochemistry

This report summarizes the electroless plating process of magnetic nickel and noncrystalline nickel for aluminium honeycomb shielded vent windows. The test results showed that the electroless nickel plating is bright in appearance, even in thickness, excellent in adhesion with aluminium substrate, good in conductivity, magnetism and corrosion resistance. Shielding efficiency obtained was 67～78 dB under 4 GHz～12 GHz frequency. Environmental reliability tests were made for 56 days under two environmental conditions, that is at 85 ℃ and 35 ℃, 95% relative humidity. The EMI shielding technical requirements of the electroless double nickel plating for aluminium honeycomb shielded vent windows of …

Effect Of Halide Ions On The Deposition Of Electroless Nickel, Keping Han, Jingli Fang

Journal of Electrochemistry

The effect of halide ions on the polarization curves and stationary potential of electroless nickel plating process were studied with electrochemical methods. The acceleration and stabilization mechanism of electroless nickel deposition by halide ions also has been discussed.

The Reduction Of Oxygen To Hydrogen Peroxide In An Acidic Trickle Bed Cell Using Graphite Chip Cathode, Zhaoe Lu, Guanyong Zhang, Tiangeng Zhong, Guonu Fang

Journal of Electrochemistry

The authors investigated the electrochemical reduction of oxygen to hydrogen peroxide in 0.05 mol/L H₂SO₄ solution by the trickle bed electrode using graphite chip. The bed dimension was 14×5×0.6 cm. The current efficiency and the concentration of H₂O₂ in the catholyte were determined at various current strengths and various rates of adding the electrolyte. The proper current was 0.15 A. i.e. the current density was 2.1 mA/cm² vertical cross section area of the bed. The concentration of H₂O₂ reached 7×10^-3 mol/L with the current efficiency of 0.2. If the …

Auger Resonant Raman Spectroscopy Used To Study The Angular Distributions Of The Xe 4d5/2 → 6p Decay Spectrum, B. Langer, N. Berrah, A. Farhat, Oliver Hemmers, J. Bozek

Environmental Studies Faculty Publications

The Auger resonant Raman effect can be used as a method to eliminate natural lifetime broadening in resonant Auger spectra. We have coupled this method with high-resolution photons from the Advanced Light Source to study angular distributions and decay rates of the Xe4d_5/2→6p resonant Auger lines. The angular distribution parameters β of almost all possible final ionic 5p⁴(³P, ¹D, ¹S)6p states have been determined. Our data, which remove the discrepancy between previous lower-resolution experimental results, are compared to different theoretical results.

Effects Of Ph, Ligand Cn-, Metallic Ions Hg2+, Cd2+ And Pb2+ On Electroactivity Of Cytochrome C, Jin Luo, Lingling Wu, Jintain Wu, Shaohua Huang, Zhonghua Lin

Journal of Electrochemistry

The effects of pH, ligtlnd CN^-, metallic ions, Hg²⁺, Cd²⁺ and Pb²⁺ on electroactivity of cytochrome c have been studied with cyclic voltammetry and UV/Vis spectroseopy. In the phosphate buffer solution containing 5 mg/mL cytochrome c, cytochrome c is electroactive at a glod electrode with suitable pretreatment if the pH value is equal to 7.0, but it is electroinactive at the gold electrode if the pH value is equal to 2.0 or 10.0. The existence of CN^- ions in the solution would cause deactivation of cytochrome c in the bulk sulurion, and would …

An Indirect Electrochemical Oxidation Of Toluene─Catalytic Effects Of Ag(Ⅰ) On Mn(Ⅱ)/Mn(Ⅲ) Couple Transition At Pt Electrode, Zhonghua Wang, Yunan Qu, Xingguo Yan, Qngmin Hua, Guacai Chen, Zhongquan Wang

Journal of Electrochemistry

The Catalytic effects of Ag(Ⅰ) on toluene oxidation by Mn(Ⅲ) as well as the anodic generation of Mn(Ⅲ) were investigated. The rates of toluene oxidation were first order with respect to both Ag(Ⅰ) and Mn(Ⅲ). Ag(Ⅱ) formed on the surface of the platinum anode when Ag(Ⅰ) was present in the anolyte, which catalyic the Mn(Ⅱ) to Mn(Ⅲ) in solution.

Ftis Observation Of Twin Adsorbates Of Co On Rh Electrode In Acid Solution, Wenfeng Lin, Shigang Sun

Journal of Electrochemistry

Because of its great importance both in electrocatalysis and C1 chemistry applications, the adsorption of CO on metallic electrodes such as Pt, Pd, Au, Ag, RhF, etc. has been extensively studied by in situ infrared spectroscopy Since 1981. In all these studies only three types of CO adsorbates, i. e., linear (2090～2000 cm^-1), bridgrd (2000～1900 cm^-1) or multi-bonded (1900～1800 cm^-1) species, were identified. A different absorbate, twin CO on rhodium (Rh(CO)₂), does exist on the solid/gas interface of highly dispersed Rh or Rhn clusters on supports, this species originating a doublet at …

Electrochemical Ploymerization Of Aniline In The Alkaline Solution And Properties Of Polymer, Shaolin Mu, Jinqing Kan, Aiguang Zhang

Journal of Electrochemistry

A deep yellow polyaniline was formed at the anodic electrode during electrochemical oxidation of aniline in the alkaline solution. The peak of oxidation potential for aniline in the alkaline solution was 0.7 V (vs.Ag/AgCl with a saturated KCl solution), which is about 0.3V less than that in the acidic solution. The results from rotating ring-disk electrode experiment show that two soluble intermediates were generated during electrochemical oxidation of aniline. The colour of the polymer in the alkaline solution is independent of applied potential and pH values. An adsorption peak was observed in the UV region at 500 nm for the …

Preparation Techique Of Foamed Nickel By Electrodeposition, Xihua He, Ronghui Hu, Hanxi Yang, Zhengzhong Zuo

Journal of Electrochemistry

This paper describes the preparation technique and operation conditions for manufacturing foamed nickel by chemilcal pretreament, electrodeposition and heat treatment. The foamed nickel made in this method showed high porosity, uniformity and considerable strength and tenacity,applicable for various secondary battery electrodes.

Study Of The Calcium-Thionyl Chloride Cells, Baohong Zhang, Meng Chen, Yingdong Wang, Dongsheng Xu

Journal of Electrochemistry

The properties of CaCl₂ SEI covered on the ca electrode surface in thionyl chloride, the influence of various salts in thionyl chloride on the porformance of the Ca anode and carbon cathode, and the function of the additive CuCl₂ and CuBr₂ to cathode in the improvement of the cathode performance were studied by AC impedance, constant current discharge, and SEM. As a result, the Ca-SOCl₂ cell was able to discharge at 50 mA·cm^-2 and the capacity reached 17.5 mAh·cm^-2.

A Study On Performance Of Electroless Nickel Coatings Containing Low Phsphorus, Huilin Guo, Xinguo Hu, Guipin Su

Journal of Electrochemistry

The low phosphorus coatings (LP) had superior corrosion resistence to that of high phosphorus (HP) in alkaline and neutral NaCl solutions. The microhardness of the coatings increaed from 454 Hv to 890 Hv when they were heated at 350℃ for one hour. Two exothermic peaks were observed at 341.6 ℃and 406.2 ℃, which respectively corresponded to form the new phases Ni₅P₂ and Ni₃P in the differential thermal analysis. The atomic structure of as-deposited coatings in the terms of X-ray diffraction had confirmed that the coatings coasisted of extremely fine crystallites.

Research On Molten Carbnate Fuel Cell, Naichao Li, Baolian Yi, Lianying Kong, Enjun Zhang, Huaxin Lin, Tianxi Qu, Yingcai Cheng

Journal of Electrochemistry

Cold-roll-milling has been evaluated as a technique for preparing porous LiAlO₂ matrices for use as a molten carbonate fuel cell electrolyte matrix. This technique produces reliable electrolyte structures with the following characteristics and advantages: ease of handling, uniform thickness, using nontoxic inorganic solvents, controlled pore size distribution, and ability to be impregnated with the alkali carbonate without fracrure.

The Molren Carbnatod Fuel Cell (MCFC) was assembled from sintered Ni electrodes and LiAlO₂ electrolyte matrix, the electrode area is 28 cm², the effect of operating conditions on cell performance was tested, it was found that the cell …

The Electrochemical Behavior Of C60-Chemically Modified Poly(N-Vinylcarhzole)In 1 Mol/L Liclo4-Thf Solutions, Yu Chen, Zuen Huang, Ruifang Cai, Fupin Zhang

Journal of Electrochemistry

The electrochemical behavior of C₆₀-PNVC copolymer in 1 mol/L LiClO₄-THF solutions has been studied by cyclic voltammetry. The results demonstrated that there are considerable differences of electronic structure between PNVC (Poly (N-vinylcarbazole)) and C₆₀-PNVC copolymer, this being consistent with the ESR results and the oxidstion-reduction activarion of pure PNVC by C₆₀-chemical modification. In the potential region, 1.3V～-3.5V, five steps, 0. 90V/0.60V, 0.20V/0.00V, -1.05V/-1.30 V, -1.25V/-1.75 V, -2.00V/-2.50V, of oxidation/reduction proceases were indicated in the cyclic voltammetry for pure PNVC, whereas seven steps, 0.20V/0.20V, -0.30V/-0.50 V, -0. 60V/-0.60 V, -0.80V/-1.10 V, -1.95V/-2.10 V, …

Study On The Manufacture Of Pt/C Gas-Diffusion Electrodes, Yonglin Ma

Journal of Electrochemistry

The various methods of manufacturing gas-diffusion electrodes are reviewed and a new method of preparing the Pt/C electrocatalyst and the gas-diffusion electrodes is explored in this paper. The electrochemical performance of resulting electrodes in concentrated phosphoric acid for oxygen reduction at 150℃ are compared with the commercial electrode which purched from Giner Inc. (U. S. A). The results show that the performance of the Pt/C electrodes which manufactured by the method in this paper has been greatly improved. Therefor, a fuel cell using such electrodes has high industrial value.

Determination Of Transport Number Of The Modified Liclo4-(Peo)20 Polymer Electrolyte, Ruqi Zhou, Qngguo Liu, Weihua Qiu, Yun Zhang, Yuee Zhao, Leiling Yang

Journal of Electrochemistry

In this work a combination method of A.C. Impedance and chronoamperometry was used to determine the lithium ion transport number of LiClO₄·(PEO)₂₀·(PC)₁₂·(EC)₁₂ polymer electrolyte. It is known that lithium is thermodynamically unstable in non-aqueous or polymer electrolytes, leading to the formtion of a film on lithium surface, called as solid electrolyte interphase (SEI). The presence of SEI layer will greatly influence the experimental result of lithium ion transport number. The new method avoid the effect of SEI layer, and can give correct transport number of lithium ion in the electrolyte of DCIO_{4 …}

Applicadons Of Laser In Electrochemistry (Ⅰ), Bin Ren, Zhongqun Tian

Journal of Electrochemistry

This paper is the first part of a comprehensive review of laser applied in electrochemistry. At first, it briefly introduces the advantages, history and exporimental setup of laser electrochamistry. Then it reviews laser applications in electrochemical deposition, polymerization, etching, polishing, corrosion, adsorption/desorption and reactions as well as photoelectrochemical switching and storage.

Study Of Electrochemical Behaviour Of Myoglobin Using Cyclic Voltammetry And Synchronous Fluorescence Spectroscopy, Ju Chou, Haihong Zhou, Tianhong Lu, Yue Wu

Journal of Electrochemistry

/

The Inhibition Of Amphipathic S- And N-Containing Compounds On Carbon Steel Corrosion, Wei Xing, Yibin Shan, Du Guo, Tianhog Lu, Shiquan Xi

Journal of Electrochemistry

Ordered monolayers of S- and N-containing amphipathic corrosion inhibitors were depoitod onto the surfaces of carbon steel electrode with super-molecular assembly technique. The effect of molecular aggregation of monolayers on carbon steel corrosion in 0.05 mol·cm^-3 H₂SO₄ and the mechanisms of these inhibitors were discussed in details. It was found that the transport of hydrated hydrogen ion to the surface of steel depends strongly on the inhibitor molecular aggregation in the monolayers.

Development Of The High Capacity Sintered Type Nickel Positive Electrode, Guohua Yu, Shijie Zhang, Xiaolin Wang, Jingqi Wei

Journal of Electrochemistry

By improving the design and technologies of the sintered type nickel oxide positive electrode for the NiMH batteries, We do our best to increase the sinter volume and porosity,the amount of the active materals and their utilization, so we have fabricated the high capacity sintered typo nickel electrodes fitting for the NiMH battreies. The sfecitic capacity of the lot produced electrodes is up to 550 mA/cm^-3.

The Influence Of Cathode Ingredients In Zinc Chloride Type Battery On The Discharge Ability, Qi Shen, Biao Zhuang

Journal of Electrochemistry

The influence of cathodic powder ingredients in ZnCl₂ type heavy duty battery on the discharge ability has been studied, a suitable battery ingredients is founds.

Electrochemical Studies On Corroding Metallic Electrodes In Frequency Domain, Chunan Cao

Journal of Electrochemistry

The electrochemical studies on corroding metallic electrodes carried out in the State Key Laberatory for Corrosion and Protection are reviewed briefly: (1) General equations of faradaic admittance under potential-control condition were derived based on the stabillity conditions of steady processes. The faradaic admittance at mixed potential then was deduced based on these equations and the electrochemical impedance spectroscopy (EIS) at corrosion potentials in the solutions containing interface inhibitors was diseussed by application of the thecetical results obtained. (2) The spectral power density (SPD) curves for electrochemical noise (EN) during the initial stagu of pitting corrosion were observed for iron and …

Kinetic Behavior Of The Pt/Ysz Solid Electrolyte Interface Exposed To O2+He Mixture, Yi Jiang, Wenzhao Li, Lixin Cao, Jingwang Yan

Journal of Electrochemistry

Electrochemical behavior of the Pt/YSZ solid electrolyre interface has been investigated by cyclic voltammetry and linear potential sweep technique. It was found that the electrochemical adsorption of oxygen on the Pt surface follows the Temkin adsorption model. The amount of oxygen species increases logarithmically with time. Two oxygen species are electrochemically formed on the Pt surface. One is atomically adsorbed, the other probably subsurface oxygen or Pt oxide. The electrochemical reduction of adsorbed oxygen is kinetically irreverable. The cathodic peak potential is affected both by the potential sean rate and the amount of oxygen ahorbed on the surface. Kinetic parameters, …

Hydrogen Evolution Reaction On Nanocrystalline Co-Mo/Ni Composite-Coated Electrodes, Weizeng Yu, Jie Ma, Yiming Chu, Huizhe Zhu, Hongjie Wang, Shuncheng Liu

Journal of Electrochemistry

The electrochemical behaviours of the hydrogen evolution reaction (HER) at electrodes prepared by composite coating of nanocrytstalline Co-Mo alloy particles formed by ball milling on nickel base has been sludied by using sleady-state polarization and ac impedance techiu ques. The microstructure and the size of the nanocrystals of Co-Mo alloy and the morphology of the composite-coating surface of the electrodes are measured by XRD, TEM and SEM. Results show that the nanocrystalline Co-Mo alloys prepared by high energy ball milling has high electrocatalytic activity for HER. The electrocatalytic activity for the HER is enhanced and the energy of activation for …

Ohmic Drop Compensation In Voltammetry:  Iterative Correction Of The Applied Potential, David O. Wipf

CAS Publications

A new method of ohmic potential drop correction for use with potential step and sweep voltammetric methods is described. The method, iterative correction of the applied potential (ICAP), essentially replaces an electronic positive feedback correction with a digital positive feedback correction. This paper will present one form of the ICAP procedure, in which voltammetric current data acquired by a high-speed digital oscilloscope are used to iteratively generate a compensating potential waveform that is then synthesized by an arbitrary waveform generator. The ICAP method is advantageous for high-speed measurements, since many of the difficulties caused by electronic positive feedback compensation are …

Dynamic Phenomena In Organic Metal (Bedt-Ttf)3ta2f11, Juana Acrivos

Faculty Publications, Chemistry

Dynamic electron spin resonance, ESR measurements suggest that this paramagnetic, layered organic metal behaves similarly to cuprate superconductors. There is a dynamic equilibrium between doublet, D and triplet, T* states near the transition temperature to superconductivity Tc= 10±3 K; antiferromagnetic, AF resonance is observed from room temperature to ≈ 150 K, in this temperature region the temperature dependence of the D Lorentzian ESR line widths obtains a first order rate constant for the disappearance of the state (k1 = 3.5 ×107 e−111/T/s) and T* ESR is not observed, it is detected only below 44 K when the lifetime of AF …

Studies Of In-Situ Raman Spectroscopy On Deprotonation And Degeneration Of Ppy Films, Jinsong Gao, Jing Chen, Yanzhen Chen, Qi Xue, Zhongqun Tian

Journal of Electrochemistry

By combining the in-situ Raman spectroscopic technique with the normal electrochemical measurements, the behavior and structure of PPY films in neutral or basic solutions were studied. The oxidized PPY loses protons on the N atoms of pyrrole rings and is deprotonated in these solutions, resulting the formation of the quinoid structure. It makes the C=C stretching vibration bonds of PPY split. Because this quinoid structure can′t be further oxidized, the PPY becomes more difficult to be oxidized and less reversible with the increasing of pH value of solutions and the degree of deprotonation of PPY. In the strong basic solution …

Catalytic Oxidation Of Methanol On Pt/C-Spe And Ptru/C-Spe Electodes, Aihua Su, Changzhi Li, Gongquan Sun, Ying Zhang, Tianhong Lu

Journal of Electrochemistry

Anode catalysts of methanol oxidation for direct methanol fuel cell, Pt/C and PtRu/C, ere prepared by chemical reduction in this work. The results indicated that the PtRu/C showed higher electrocatalytic activity than that of Pt/C. It was explained by XRD and XPS analyses that the existence of Ru enhanced the catalytic activity for electrochemical oxidation of methanol.