Chemistry Commons^™

Electropolymerization And Characterization Of Thin Film Dielectrics, Christopher White Ii

Department of Chemistry: Dissertations, Theses, and Student Research

Graphene is a two-dimensional allotrope of carbon, with several superlative properties, including high electron and hole conductivities, high tensile strength, and chemical robustness. Its chemical and physical properties make it attractive for in use in a myriad of applications, including transistors. However, graphene’s chemical inertness and its physical and electrical properties’ dependency on its conjugated structure make building composite materials with graphene difficult. In 2015, Lipatov, et. al. demonstrated that a film derived from electropolymerized phenol could be used as a dielectric layer on transistor devices fabricated from exfoliated graphene. This thesis extends that research, detailing experiments of phenol and …

A Simple And Effective Way To Overcome Carbon Monoxide Poisoning Of Platinum Surfaces In Direct Formic Acid Fuel Cells, Yaser M. Asal Mr., Islam M. Al-Akraa Dr, Sohair A. Darwish Ms

Chemical Engineering

A glassy carbon (GC) electrode modified with multi-walled carbon nanotubes (MWCNTs) and platinum nanoparticles (PtNPs), Pt/MWCNTs-GC, has been introduced for formic acid electro-oxidation (FAO). A similar loading of PtNPs has been conserved for a proper comparison between the Pt/MWCNTs-GC and the unmodified Pt/GC electrodes. The modification with MWCNTs could enhance the loading of PtNPs onto the GC electrode in a way that minimizes its agglomeration and increases its dispersion in the CNTs network. This not only increases the surface area exposed to the reaction but also interrupts the contiguity of the Pt active sites minimizing the adsorption of the poisoning …

A Promising Modification Of Pt Surfaces With Cnts For Decreasing Poisoning Impact In Direct Methanol Fuel Cells, Yaser M. Asal Mr., Islam M. Al-Akraa Dr, Aya A. Khalifa Ms.

Chemical Engineering

Direct methanol fuel cells (DMFCs) are clean energy sources that have many applications due to the high energy density of methanol as a fuel. However, this type of fuel cells (FCs) has limitations that are preventing it from being commercialized. One such limitation is the adsorption of intermediates such as CO into the surface of the Platinum (Pt) catalyst during methanol oxidation (MO) which deactivates its active sites, where the reaction is taking place, and leads to poisoning of the electrode over the long term. In this study, multi-walled carbon nanotubes (MWCNTs) have been introduced to the Pt-modified glassy carbon …

Photoswitchable Self-Complementary Hydrogen Bond Arrays, Suendues Noori, James A. Wisner

Western Research Forum

Background: Photochromism is the reversible transformation of a chemical material to another form by the absorption of electromagnetic radiation (light), where the two metastable forms have distinct absorption spectra and other properties. Photochromism in materials allows for the switching of their function solely based on irradiation with light. Polymers are used frequently as the building blocks for materials as they are versatile, multifunctional, can carry charge and be processed by solution-based deposition methods. Supramolecular polymers share the same definition as polymers with the exception that they are held together by reversible and directional non-covalent interactions such as hydrogen bonds. Synthesizing …

Recent Advances In Nanofluidic Electrochemistry For Biochemical Analysis, Zhong-Qiu Li, Zeng-Qiang Wu, Xing-Hua Xia

Journal of Electrochemistry

Nanofluidics, as a young research field, has been receiving more and more attentions. It has been successfully applied in various fields including nanoscale separation, biochemical sensing and energy conversion. The development of nanofluidics is closely related to electrochemistry that can provide a driving force for the study of the material transport characteristics in nanopores/nanochannels. On the other hand, nanopores/nanochannels can creat a microenvironment for study of spatially nanoconfined electrochemistry. The combination of nanofluidics and electrochemistry has given rise to many new theories and technologies for single molecule/particle analysis and nanofluid manipulation. Herein, we provide a review of the recent progresses …

Study On The Relationship Between Structure Of Supramolecular Ion Material And Performance Of Humidity Sensing, Hui-Min Tang, Hai-Long Yan, Li Zhang, Jun-Jie Fei, Ping Yu, Lan-Qun Mao

Journal of Electrochemistry

Humidity measurement and control is one of the most notable issues in various areas, such as climate, industry,
agriculture, electronics, especially human comfort and health. In our previous study, we have found that a new kind of supramolecular
ionic material (SIM), consisting of an imidazolium-based dication (e.g., 1,10-bis(3-methylimidazolium-1-yl) decane, C₁₀(mim)₂) and
electroactive dianionic (e.g., 2,2'-azino-bis (3-ethylbenzothiazoline-6-sulfonic acid), ABTS), shows ultrasensitive and ultrafast
response towards humidity sensing. Herein we prepared six kinds of imidazolium-based dications with different carbon chain
lengths (i.e., C₄, C₆, C₈, C₁₀, C₁₂, C …

Electrocatalytic Nanomaterials For Reduction Of Hydrogen Peroxide As Potential Radioprotectors, Rui-Hong Jia, Jin-Xuan Zhang, Xiao-Dong Zhang, Mei-Xian Li

Journal of Electrochemistry

Nanomaterials have shown many potential application prospects in the biomedical field, such as medical imaging, drug delivery and biosensing due to their unique physical and chemical properties. In this review we focus on nanomaterials that have shown not only abilities of radiation protection, but also good electrocatalytic activities toward reduction reactions of hydrogen peroxide and oxygen. We discuss the abilities of radiation protection of these nanomaterials that are ascribed to their enzyme-like activities because their catalytic properties provide an effective pathway for scavenging free radicals in vivo via rapid reactions with reactive oxygen species. We also provide insights into electrocatalytic …

Electrochemical Biosensors For Wastewater-Based Epidemiology, Yu-Wei Pan, Kang Mao, Franziska Tuerk, Zhu-Gen Yang

Journal of Electrochemistry

Wastewater-based epidemiology (WBE) has been shown to be an innovative approach for evaluation of drug use trends and public health assessment by quantifying drug residues and/or metabolites (so-called biomarkers) in wastewater collected in a local treatment plant. Community sewage sensors have been proposed and demonstrated to be powerful tools for the analysis of sewage biomarkers. In particular, electrochemical biosensors have emerged as a rapid method for the analysis of biomarkers and pathogens in wastewater due to low cost, minimal sample processing and the ability to test in the field. It has been widely used for biomedical diagnosis, environmental monitoring and …

A Low Noise Temperature Control System For Nanopore-Based Single Molecule Analysis, Cheng-Yu Yang, Zhen Gu, Zheng-Li Hu, Yi-Lun Ying, Yi-Tao Long

Journal of Electrochemistry

Nanopore employs a single bio-molecule interface, which is a highly sensitive single-molecule detection technology for measuring single biomolecules such as DNA, RNA, protein, and peptide. The interaction between single molecule and nanopore is thermodynamically controlled. Therefore, it is urgent to precisely control the temperature of the nanopore system without introduction of any noise. In this paper, we have developed a low-noise temperature control system for single-molecule detection of nanopores to achieve precise regulation at the ambient temperature during measurements. The system utilizes the thermoelectric effect of the semiconductor refrigerating chip to heat or cool the detection chamber, while adopts electromagnetically …

Single Particle Impact Electrochemistry: Analyses Of Nanoparticles And Biomolecules, Jian-Hua Zhang, Yi-Ge Zhou

Journal of Electrochemistry

Single particle impact electrochemistry (SPIEC) has grown rapidly in recent years and shown great promise in the analysis of nanoparticle properties as well as the detection of biomolecules including DNA, RNA, protein, enzyme, bacteria, virus, vesicles and others. This minireview summarizes recent advances in electroanalytical applications of SPIEC according to different analytical methods, i.e., direct electrolysis of nanoparticles or labeled nanoparticles, direct electrolysis of soft particles encapsulated redox molecule, indirect electrochemistry of particles, area and diffusion blocking, and changes in current magnitude and collision frequency.

Cysteine And Cystamine Co-Self-Assembled Monolayers For In Vivo Detection Of Ascorbic Acid, Yue Zhang, Tao-Tao Feng, Wen-Liang Ji, Mei-Ning Zhang

Journal of Electrochemistry

Self-assembled monolayers (SAMs), which form highly ordered monolayers on the electrode surface through the gold-suffer bond, have attracted much attention in recent years. This stable layer not only can regulate the wettable properties of surface, but also can act as a promoter towards redox-active molecules. Here, we developed a simple and effective method to construct cysteine and cystamine co-self-assembled monolayer on gold microelectrode for  in vivo detection of ascorbic acid (AA). The molar ratio at 1:1 of mixed monolayer has been found the optimum to enhance the electron-transfer kinetics of AA oxidation at low potential (ca. 0.10 V), meanwhile, it …

Current Statuses And Challenges Of Wearable, Flexible Electronic Sensors And Energy Storage Devices, Zhong-Qian Song, Fang-Jie Han, Hui-Jun Kong, Jia-Nan Xu, Yu Bao, Dong-Xue Han, Li Niu

Journal of Electrochemistry

With the developments in the internet of things, artificial intelligence and human-computer interaction technology, soft, flexible and wearable electronic devices provide a novel platform for monitoring of the human vital signs, and recognition of human behaviors to connect human being and machine without consciousness. Recent progresses about wearable and flexible electronics that can provide accurate, non-invasive, long-term and continuous monitoring of human vital sings including pulse, temperature, skin activities, breathing and heart rate are summarized. The working mechanisms, current statuses and challenges in temperature sensor, strain sensor and pressure sensor are discussed. The review concludes with a prospect of current …

Approaches For Sample Characterization And Lithography With Nanoparticles Using Modes Of Scanning Probe Microscopy, Jayne C. Garno, Temitope O. Jegede, Kathryn B. Mckee, Melissia Porter, Autumn E. Webb, Jin Gyun Lee, Neepa Mk Kuruppu Arachchige, Justin R. Ragains, Noémie Elgrishi

Faculty Publications

Measurement and imaging modes of scanning probe microscopy (SPM) have been routinely applied for characterizing systems of nanoparticles; however the evolution of fabrication methods to prepare arrangements of nanoparticles remains a challenge. Reproducible fabrication of surface structures which integrate nanoparticles within ultra-small patterns will require innovative approaches to achieve high throughput and precision. Strategies for nanoscale lithography have been introduced for preparing defined arrangements of nanoparticles on surfaces based on physical or chemical interactions. For example, physisorption was employed for attaching nanoparticles based on colloidal lithography and site-directed assembly. Microfabricated atomic force microscope (AFM) tips with capillary channels have been …

Implementation Of Multivariate Artificial Neural Networks Coupled With Genetic Algorithms For The Multi-Objective Property Prediction And Optimization Of Emulsion Polymers, David Chisholm

Master's Theses

Machine learning has been gaining popularity over the past few decades as computers have become more advanced. On a fundamental level, machine learning consists of the use of computerized statistical methods to analyze data and discover trends that may not have been obvious or otherwise observable previously. These trends can then be used to make predictions on new data and explore entirely new design spaces. Methods vary from simple linear regression to highly complex neural networks, but the end goal is similar. The application of these methods to material property prediction and new material discovery has been of high interest …

Monolayer Triphosphates Mp3 (M = Sn, Ge) With Excellent Basal Catalytic Activity For Hydrogen Evolution Reaction, Hong-Hui Wu, He Huang, Jie Zhong, Song Yu, Qiaobao Zhang, Xiao Cheng Zeng

Xiao Cheng Zeng Publications

Atomically thin two-dimensional (2D) materials have received intense research interest due to their novel properties and promising applications in nanodevices. By using density functional theory (DFT) calculations, we investigate catalytic activities of several newly predicted two-dimensional (2D) triphosphides GeP₃, SnP₃ and InP₃ monolayers for hydrogen evolution reaction (HER). The calculation results show that GeP₃ and SnP₃ monolayers are active catalysts for HER with suitable free energy of hydrogen adsorption in the basal plane. In particular, the Gibbs free energy of hydrogen adsorption (ΔG_H*) of GeP₃ is 0.024 eV, a value even …

Rheological Investigations Of Latex-Surfactant-Associative Thickener Aqueous Systems, Bishop I. Hammack

Master's Theses

Surfactants and Thickeners are both additives used in fully-formulated waterborne coatings to provide colloidal stability, thickening, and other functionality. The behavior of each ingredient in a coating must be understood and controlled to maintain colloidal stability as well as balance other desired properties of the liquid coating and the dry paint film. In this work, quaternary systems of Water-Latex-Thickener-Surfactant were investigated to further the understanding of their behavior in coatings. The thickener used was a well characterized, hydrophobically-modified, ethoxylated urethane (HEUR) with two C18 terminal hydrophobes and 795 average repeat units of ethylene oxide as the hydrophilic spacer. Two latexes, …

Nano Fab Lab 63, Brian K. Deemer, Josh Clemons, Nick Brodine, Delaney Fitzsimmons

Mechanical Engineering

Lawrence Livermore National Laboratories (LLNL) has several steps in the production process for ceramic nanofiber tubes that they would like to improve - electrospinning, cutting, rolling, sealing and heat treating. We undertook the challenge to deliver LLNL with a semi-automated process that efficiently integrates the steps of cutting, rolling, and sealing to save time and improve control over end dimensions. In this document, we discuss the technical background of the manufacturing steps currently followed to create nanofiber tubes, identify which steps are incorporated in our prototype and explain how they will interface with one another, define the design requirements, present …

Incorporation Of Gold Nanowires Into Photovoltaic Devices, Scott W. Gordon

LSU New Orleans Theses and Dissertations

To this day, fossil fuels still make up over 80% of the earth’s energy production. Many sources of renewable energy are available, but photovoltaics is the only source with the capacity proven to meet the increasing world energy needs. Third generation devices such as dye-sensitized and organic solar cells have gained much interest due to their cost effectiveness and flexibility but have yet to become commercially viable. Here methods have been studied to improve these devices with the use of Gold nanowire arrays. These additions provide plasmonic and light scattering enhancements in dye-sensitized solar cells. Different TiO2 deposition methods have …

An In-Situ Study Of The Aqueous Speciation Of Uranium (Vi) Under Hydrothermal Conditions, Diwash Dhakal

Graduate Theses/Dissertations

Rigorous study of the speciation distribution of uranyl-chloride bearing solutions under hydrothermal conditions is important to understand the transport mechanism of uranium underground, which is of uttermost interest to parties studying the geological uranium deposits and those studying the possibilities of geological repositories for spent nuclear waste. I report an in-situ Raman spectroscopic study of the speciation distribution of aqueous uranyl-chloride complexes upto 500°C conducted using a HDAC as the high PT spectroscopic cell. The samples studied contained the species UO₂²⁺, UO₂Cl⁺, UO₂Cl₂⁰ and UO₂Cl₃^{- …}

Concentration-Dependent Magnetic Properties Of Mnxnio1-X Novel Inverted Core-Shell Nanoparticles, Md Nazmul Alam

Graduate Theses/Dissertations

The doping concentration (Mn concentration) dependent magnetic properties of NiO@NixMn1-xO novel inverted core-shell magnetic nanoparticles are of great interest of this present research. Primarily, we investigated the oxidation state of Ni from size-dependent four NiO NPs samples, and then studied the variation in the magnetic properties of Mn concentration-dependent NiO@NixMn1-xO CNPs. The NiO nanoparticles were synthesized using a thermal decomposition method. The XRD data indicates that the crystal structure (rock salt) remains fixed in all NiO samples and XPS data shows the oxidation state of size-dependent NiO nanoparticles is 2+. The hydrothermal epitaxy method was used to incorporate Mn in …

Photo-Physical Properties Of Novel Gumbos For Optoelectronic Applications, Thenahandi Prasanthi Deepthika De Silva

LSU Doctoral Dissertations

Organic Light Emitting Diodes (OLEDs) are predicted to revolutionize next generation consumer electronics by offering many advantageous device characteristics, including low power consumption, low heat dissipation, a tunable and wider color gamut, high resolution and contrast, light weight, flexibility, and semi-transparency. However, a major limiting factor for OLEDs to reach their full potential is that only a few known blue OLED emitters with substantial spectral purity and longevity are available to date. Therefore, focus of this research is on understanding and addressing limitations of OLED emitters, with an emphasis on improving the characteristics of blue emitters.

The work presented in …

Application Of X-Ray Grating Interferometry To Polymer/Flame Retardant Blends In Additive Manufacturing, Omoefe Joy Kio

LSU Doctoral Dissertations

X-ray grating interferometry is a nondestructive tool for visualizing the internal structures of samples. Image contrast can be generated from the absorption of X-rays, the change in phase of the beam and small-angle X-ray scattering (dark-field). The attenuation and differential phase data obtained complement each other to give the internal composition of a material and large-scale structural information. The dark-field signal reveals sub-pixel structural detail usually invisible to the attenuation and phase probe, with the potential to highlight size distribution detail in a fashion faster than conventional small-angle scattering techniques. This work applies X-ray grating interferometry to the study of …

Synthesis, Characterization And Crystal Growth Of I2-Ii-Iv-Vi4 And I4-Ii-Iv2-Vi7 Diamond-Like Semiconductors With Potential In Ir-Nlo Applications, Jennifer Glenn

Electronic Theses and Dissertations

In this dissertation, several new and existing diamond-like semiconductors (DLSs) were synthesized and investigated for their potential in infrared nonlinear optical (IR-NLO) applications. In Chapter 2 growth of large single crystals of Li₂MnGeS₄ was carried out using iodine vapor transport and a newly created graphite-tube containment system. This crystallization method produced sizable single crystals on the scale of 2x1x1 mm³, that were used to determine the material’s magnetic properties. Magnetization data indicate that the compound is antiferromagnetic with a Néel temperature of 10 K and an effective magnetic moment of 5.6 /f.u.. The specific heat …

Engineering Multifunctional And Morphologically Diverse Polymer Brush Surfaces, Cassandra M. Reese

Dissertations

The combination of surface-initiated polymerization (SIP) and post-polymerization (PPM) serves as a powerful approach to fabricate complex, multifunctional polymer films, which can be precisely tuned for desired surface engineering applications. Careful manipulation of PPM parameters such as reaction conditions, the tethered brush parameters, and the physical properties of the unbound post-modifier greatly influence the depth of penetration of the post-modifier and the polymer brush compositional heterogeneity. This dissertation focuses on engineering polymer brush surfaces with multifunctional chemistries and tunable morphologies by investigating the PPM parameters that dictate the distribution of post-modifiers on grafted polymer brush surfaces.

The first chapter of …

Deposition Of Platinum Particles On Surface-Modified Carbon Ultramicroelectrodes, Caitlin Millsaps

Undergraduate Honors Theses

Nanoparticles are used as electrocatalysts due to their large surface area-to-volume ratios. Most studies of nanoparticle electrocatalysis are performed on collections of particles on a support, which represent ensemble average behavior influenced by spatial distribution of the nanoparticles. Therefore, recent emphasis has been placed on analyzing electrocatalytic behavior of single particles. The focus here is to develop carbon ultramicro- and nanoelectrode platforms for studying the electrocatalytic properties of single metal nanoparticles. Ultramicroelectrodes were prepared using chemical vapor deposition of carbon in pulled quartz capillaries. Electrode diameters were determined by cyclic voltammetry. Electrodes were modified using a soft nitriding technique to …

Surface Immobilization Of Terpyridine Compounds, Elizabeth Hallett

Chemical Engineering Undergraduate Honors Theses

The deoxydehydration (DODH) of polyols to alkenes is a promising method of producing high-value chemical feedstocks from biomass-derived materials. Current catalytic systems for DODH require the use of costly reducing agents that generate stoichiometric amounts of chemical waste. Immobilizing catalysts on electrode surfaces using chemical linking groups eliminates the need for sacrificial reductants. In this work, glassy carbon electrodes were modified with 4’-(3,4-dihydroxyphenyl)-2,2’:6’,2’’-terpyridine to investigate o-benzoquinone as a potential linking group for DODH, and possibly for other reactions. Previous studies involving electrodes modified with quinone-containing compounds have primarily been focused on catalyzing the oxidation of NADH; the nature or …

Synthesis And Characterization Of Dielectric And Multiferroic Nanocrystalline Transition Metal Oxide Materials And Nanocomposites, Frederick A. Pearsall

Dissertations, Theses, and Capstone Projects

Nanocrystalline transition metal oxides with unique chemical, physical, magnetic and dielectric properties have very broad applications, ranging from photocatalysis, capacitor energy storage and 4-state memory. Frequency stable, high permittivity nanocomposite capacitors produced under mild processing conditions offer an attractive replacement to MLCCs derived from conventional ceramic firing. In one project reported herein, 0-3 nanocomposites were prepared using BaTiO₃ (barium titanate, BTO) nanocrystals, suspended in a poly(furfuryl alcohol) matrix, resulting in a stable, high effective permittivity, low and stable loss dielectric. Effective medium approximations were used to compare this with similar nanocomposite systems. The use of synthesized BTO nanocrystal photocatalysts …

Mild Synthesis Of Perylene Tetracarboxylic Monoanhydrides With Potential Applications In Organic Optoelectronics, Xizhe Zhao

Dissertations, Theses, and Capstone Projects

Perylene tetracarboxylic derivatives are considered good n-type semi-conductors. In past decades, there has been extensive study on their synthesis and electronic properties. Because of the high electron affinity, the ability to form π-π stacks, they have been widely utilized in organic photovoltaic solar cells, field-effect transistors and light-emitting diodes. Many of those applications prefer unsymmetrically substituted perylene tetracarboxylic derivatives. Perylene monoanhydrides are the most versatile intermediates for the preparation of unsymmetrically substituted perylene tetracarboxylic derivatives. In this thesis, I focused on introducing new synthesis methods for perylene monoanhydrides with labile functional group and their potential applications in organic optoelectronics.

In …

Peptide Mediated Co-Assembly Of Porphyrin: Towards Sustainable Biomaterials For Light Harvesting And Catalysis, Wsm Nadeesha K. Wijerathne

Dissertations, Theses, and Capstone Projects

The diverse molecular functions of naturally occurring biomaterials designed from proteins are fundamentally based on a set of conserved building blocks, namely the 20 gene coded amino acids. The supramolecular structures and functions of proteins dictates by the self-assembly, where the complexity of proteins arise from a large number of amino acids. Generation of biomimetic systems that resemble the structures and functions of proteins is of great interest yet challenging due to the tremendous complexity of the natural systems. It is important to investigate alternative strategies to design much simpler systems that exhibit the same or similar function as proteins. …

Raman And Surface Enhanced Raman Spectroscopy For Forensic Analysis: Case Studies On The Identification Of Illicit Substances And Artist Pigments, Abed Haddad

Dissertations, Theses, and Capstone Projects

Raman spectroscopy is an effective tool for detecting trace amounts of material by fingerprint-like vibrational spectra. At times, the weak intensity of Raman scattering can make it difficult to distinguish trace materials. This shortcoming is addressed by surface‐enhanced Raman spectroscopy (SERS), which produces strong signal enhancements when target compounds are near metal nanoparticles. For the first part of this thesis, the identification of fentanyl and carfentanil, main culprits in the opioid epidemic, was done using normal Raman and the SERS spectroscopy. As an aid in the assignment of the spectral lines, a computational model was built using Density Functional Theory …