Chemistry Commons^™

Progresses In The Studies On Electrochemical And Surface Properties Of Hydrogen Storage Alloy Materials, Yong Yang, Jum Li, Zugeng Lin

Journal of Electrochemistry

Recent progresses in the studies on electrochemical and surface properties of hydrogen storage alloy materials are reviewed. This paper includes three sections: 1) Thermodynamic and kinetic studies of metal hydride electrodes, 2) Effects of micro structure and alloy elements of the materials on the electrochemical properties of the electrodes and 3) Correlation between surface properties of the alloy materials and performance of the negative electrode in the nickel metal hydride batteries.

Quantitative Evaluation Of Electrochemical Properties Of Mh Alloy By Powder Microelectrode, Ronghui Hu, Hanxi Yang, Jingcheng Liu, Shengxian Li, Chuanxin Cha

Journal of Electrochemistry

In this paper, a quantitative method by use of powder microelectrode combined with cyclic voltammetry and galvanostatic step is described for studying the electrochemical performance characteristic of hydrogen storage alloy(MH). Since the powder microelectrode uses only MH powder and has its depth and diameter of several tens of micrometer, the ohmic and concentration ploarization are greatly reduced and the influences of the technical factors in electrode preparation on the material performance are simply eliminated. Thus, with accurate determination of the load quantity of MH alloy in power microelectrode by absorption spectrometric technique, it is feasible to evaluate quickly and quantitatively …

Comparison Of The Charge/Discharge Charasteristics Between Ni-Cd And Ni-Mh Battery And Its Improvement Of Manufacture Technique, Yumimg Wang, Jinsheng Chen

Journal of Electrochemistry

Based on the difference of charge discharge charasteristies between Ni-Cd and Ni-MH battery, some appropriate manufacture technoque to improve the battery performances or to extend its service life are adopted.

An Esr Study Of Free Radicals In Electroreduction Process Of Allyl Alcohol, Jindong Zhang, Yafei Kuang, Shukun Huang, Naixian Xie, Fengzhen Wang, Dewen Chen

Journal of Electrochemistry

Electrochemical-ESR technique with spin trap phenyl-t-butyl nitrone(PBN)was used to study the intermediates of electroreduction of allyl alcohol at platinized platinum electrode in acidic alcohol-aqua solution. Hydrogen and allyl group and(or)propyl group radicals were identified by a hyperfine spectrum of the radical adducts, and that provided a direct evidence for the presence of these radicals in the electroreduction of allyl alcohol.

A Study On Solid Polymer Electrolyte Fuel Cell, Hongfeng Xu, Ming Han, Baolian Yi, Xinge Zhang, Shanhai Ge

Journal of Electrochemistry

Solid polymer electrolyte fuel cell (SPEFC) show promise of a high level of performance in the present fuel cell. In this paper, we report the method of SPEFC electrode preparation,and the effects of temperature, pressure and gas flow rate on the performance.

Improvement Of The Anti-Interference Characteristics Of God Electrode By Using The Powder Microelectrode Technique, Chen Jian, Chuansin Cha

Journal of Electrochemistry

The electrochemical behavior of ascorbic acid(AA), uric acid(UA), L-cystein(L-Cys) and acetaminophen (APAP), i.e. The main interference to the GOD electrode, were studied at the Pt,GC and powder microelectrode. Experimental results indicated that, due to the electrochemical activity of these interference, it is difficult to eliminate their interference effects by manipulation of electrode materials or working potential of the GOD electrode. However, it was found that the limiting curtents at the KB electrode are mainly controlled by mass transfer in liquid phase, so it is only related to the geometer size of the electrode, not its real surface area. Therefore, it …

Studies On The Charge And Discharge Reaction Of Li/Lini0.3Co0.7O2 Battery, Fupjng Zhang

Journal of Electrochemistry

The charge and discharge reaction of Li/LiNi_0.3Co_0.7O₂ battery have been studied by using CV,CT,XRD and GCP. It is shown that the discharge capacity of the cell reaches 120-140 mA·h·g^-1 in the 4.30-3.00 V in 1 mol/L LiClO₄/PC electrolyte system. The discharge mechanism involve a two-step Li⁺ intercalation reaction. The thermodynamic data such as ΔG,ΔS, ΔH, of the reaction are given. Furthermore, the changes of the D or σ_i of Li⁺ with its composition have been discussed.

The Effect Of Co On The Proton Diffusion Coefficient For The Ni(Oh)2 Electrodes, Xiaoyan Cao, Zuoxiang Zhou, Huatang Yuan, Yunshi Zhang

Journal of Electrochemistry

The diffusion coefficients of protons moving in the Ni(OH)₂ electrodes have being investigated by constant current, cyclic voltammetry and potential step technineques. The electrodes were prepared by cathodic deposition and their active material contained 0～53% cobalt. It was found that the diffusion coefficients are about 10^-9～10^-10 cm²/s during charging and about 10^-11 cm²/s during discharging. Moreover the value increases with the increacing content of Co in the electrodes. During the calculation, the relevant fomulars were modified especially the wrong fomular for constant current methode.

Electrochemical Study Of The Corrosion Behavior Of Coalesced Copper And Sw-206 Stainless Steel In The Acetic-Acid Solution, Rongzong Hu, Changjian Lin, Jianguang Tan, Zhanmei Sun, Xueqin Wu, Biao Wang

Journal of Electrochemistry

In order to provide a theoretic and experimental consideration for the material selection and anit-corrosion in the petrochemical industries the corrosion behavior of coalesced copper and sw-206 stainless steel in the acetic acid solution was studied by electrochemical impedance spectroscopy and polarization techniques. The effects of the temperature, acetic acid concentration and solubilized oxygen in the acetic acid solution on the corrosion process of this two metals were analyzed. It was found that these effects obviously accelerate corrosion process for the coalesced copper, but no apparent influnce for the sw-206 stainless steel.In the the acetic acid solution, containing water and …

Electrodeposition Of Cu-Co Multilayer Thin Films, Jiangyun Xue, Jixun Wu, Dejun Yang

Journal of Electrochemistry

A method has been developed to produce Cu-Co Multilayer from a single electrolyte by electrodeposition. The effects of the concentration of copper ions, current density and the speed of rotation were investigated, and the Cu-Co electrodeposition films were analysed by TEM, AES and X-ray diffraction. The results indicated that the film was alternating pure copper and coppercobalt alloy layers. If the content of copper in cobalt layer is to be small, the concentration of its ions in solution must be small and the rotation speed must be low.

A Study On Electrochemical Oxidation Of Reduced Nicotinamide Coenzyme Nadh In Organic Media, Fangzu Yang, Huihuang Wu, Shukai Xu, Shaomin Zhou

Journal of Electrochemistry

The behaviour of electrochemical oxidation of the reduced nicotinamide coenzyme NADH on glassy carbon was studied and some kinetic parameters were measured by means of voltammometry in the N-dimethylformamide (DMF) and 1,4-dioxane media respectively. The eletrochemical oxidation of NADH shows completely irriversable both in the two solvents,and the diagnostic experiments support that the process involves a fast chemical step.The oxidation rate and the diffusion coefficient of NADH in DMP are smaller than those in 1,4-dioxane, but the response current is more stable in DMF. The experimental results are discussed by solvent effects.

Study On The Growth Process Of Lead Dioxide On Lead-Antimony Electrodes By Impedance Tracing Method, Guolin Wei, Hongxin Yang, Jiarong Wang

Journal of Electrochemistry

The growth process of PbO₂ formed by the oxidation of PbSO₄ in the anodic film on lead-(1,3,5,7)wt% antimony electrodes was investigated with impedance tracing method of single frequency and the current-time transient method. The influence of antimony on this process was studied.The simulation curves obtained for capacity-time transients fit the experimental results very well. It has been shown that the mentioned growth process is a two-dimentional instantaneous nucleation and growth process. Antimony will inhibit the growth of PbO₂ nucleus but enhance its nucleation.

A Preliminary Study Of Electrochemically Amplified Measurement Of Gold Electrodeposition, Bingwei Mao, Caihui Shi, Xiaoqin Li, Lihua Xiong

Journal of Electrochemistry

Gold electrodeposition onto a glassy carbon microelectrode is studied using an electrochemical amplification method. Taking the advantage that the electrochemical reduction of K₂Cr₂O₇ has significantly higher reaction activity on gold electrode than carbon electrode, it is tentatively used to amplify the gold electrodeposition current. The results show that there is a marked increase in current of gold electrodeposition in presence of K₂Cr₂O₇ in comparison with that absent of K₂Cr₂O₇.The electrochemical amplification method can be applied to study the electrodeposition of very in intial stage …

Surface Raman Spectra Obtained From Various Electrodeposited Transidon Metals, Jingsong Gao, Bin Ren, Qunjian Huang, Zhongqun Tian

Journal of Electrochemistry

Good quality potential-dependent surface Raman spectra of pyridine were obtained for the first time from a series of transition metals, e. g., Fe, Co, Ni, Ru, Rh, Pd and Pt, which were electrodeposited on non-SERS-active substrates. The influences of the applied potential and the nature of metal on the adsorption behaviors were discussed briefly. This result illustrates that Raman spectroscopy is becoming a more general and powerful tool to study various electrochemical interfaces.

Electrocatalytic Reduction Of Nitrite In The Presence Of Complex Of Cobalt(Ⅱ) And 1,10 Phenanthroline, Jian Tong, Xiaojun Dang, Hulin Li

Journal of Electrochemistry

The electrochemistry of cobalt(Ⅱ)-1,10-phenanthroline Co(Phen)₂²⁺ complex and its ability to electrocatalyze the reduction of nitrite were studied, we found that this complex could act as a catalyst in alkaline or neutral solution for nitrite reduction. We have investigated the effect of the complex composition on electrocatalytic ability. The effects of pH value, complex concentration, regeneration and activation of electrocatalyst on the catalytic current have been studied and discussed.

Study On Electrode Constructure And Electrical Performance Of Na/S Cell, Jianhua Yang, Jiadi Cao

Journal of Electrochemistry

A sodium wick for sodium electrode and trough shaped performs for sulfur electrode in Na/S cell were designed and investigated. The experiments suggested that the sodium wick for sodium electrode not only improved the discharge performance of cell but also reduced the quantity of sodium utilization, and increased the specific energy of Na/S cell. The trough shaped preform with alumina fibres for sulfur electrode decreased the polarization, improved the charge acceptance and prolonged the life of cell.

Studies Of Surface Treatment Methods And Their Operating Mechanisms For Activation Of Hydrogen Storage Electrode, Ronghui Hu, Hanxi Yang, Shigang Lu, Shengxian Li, Jingcheng Liu, Chongzhi Yang

Journal of Electrochemistry

Surface treatment methods by use of charge discharge cycling, KBH₄ reduction and KOH etching were parallely investigated for the rapid activation of Mn(NiCoMnAl)₅ electrode. It is found that the MH electrode treated with hot and concentrated KOH solution exhibits rapid and full activation, and also gives lower discharge overvoltage, higher stable capacity and improved cycleability. It is also revealed from SEM, EDAX and ICP analysis that the KOH activation of the electrode proceeds mainly through the enrichment of mischmetal and nickel in surface to form electrocatalytically active surface for hydrogen absorption reaction, but the surface modification with KBH …

The Applications Of Poap Ni2+ Films Modified Electrode As Sensor For Alcohol, Bingzeng Hua, Wenyun Hu, Yanzhen Chen

Journal of Electrochemistry

POAP Ni²⁺ films modified electrode can electrocatalyzes significantly the oxidation of alcohol. The modified electrode can be used as the electrochemical sensor for the detection of alcohol. But the oxidation of alcohol is effected by the thickness of films、the concentration of nickel ion in films, pH of electrolyte, as well as temperative. All of those conditions have been studied in order to achieve stable response current during the oxidation of alcohol, and the relation between concentration and current has been made. At last the major characteristic parameters, such as the low limitation of concentration, the response time, the ability …

Problems On The Study Of Anodic Films On Pb In Sulfuric Acid Solution (Ⅱ), Houtian Liu, Qunzhou Wang, Yongqin Wan, Weifang Zhou

Journal of Electrochemistry

The conditions for the growth of the different phases in the anodic Pb(Ⅱ) film on Pb in sulfuric acid solution were discussed.

Status Of The Research And Development For Fuel Cell Technology Abroad, Naichao Li, Baolian Yi

Journal of Electrochemistry

Status of the research and development for fuel cell technology abroad was overviewed, and at the aim of accelerating the research and development for fuel cell technology in China, the corresponding stategy for our country was recommended.

Surface Raman Spectra Of Pyridine And 2 Mercaptopyrimidine Adsorbed On Rough Nickel Electrode, Qunjian Huang, Jinsong Gao, Xiongwei Cai, Bingwei Mao, Mingsen Zheng, Zhongqun Tian

Journal of Electrochemistry

The Raman spectra of pyridine and 2-mercaptopyrimidine (2-MP) adsorbed on bare nickel electrodes roughened by a HNO₃ etching procedure have been obtained for the first time by utilizing a highly sensitive confocal Raman microscope. Their adsorption behaviours are discussed briefly. This primary result illustrates a great potential for in-situ Raman spectroscopy in the study of chemical and electrochemical processes of transition metal surfaces.

Electrocatalytic Oxidation Of Some C2 Compounds (Alcohols, Aldehydes, And Carboxylic Acids) On A Pt/SbAd Electrod, Hong Li, Lincai Jiang, Xiong Jiang

Journal of Electrochemistry

The electrocatalytic oxidation behavior of some C₂ compounds(alcohols, aldehydes and carboxylic acids) on a Pt/Sb_ad electrode prepared in-situ or ex-situ UPD was investigated using pontential sweep and rotating disc electrode methods. It is confirmed that Pt/Sb_ad electrode show the most electrocatalytical active to the oxidation of aldehyde functional group and only a little activity to the oxidation of hydroxyl group, but no activity for the oxidation of carboxyl group.

The experimental results show that the activity of the Pt/Sb_ad electrode prepared by ex-situ UPD is higher than that prepared by in-situ UPD.

The limitations of the …

In Situ Studies Of Copper Electrodepostion On Hopg By Using Ecstm, Zhaoxiong Xie, Bingwei Mao, Xiangdong Zhuo, Jiqian Mu, Zhaowu Tian

Journal of Electrochemistry

In this paper, copper electrodepostion on HOPG had been in situ studied by using a homebuilt electrochemical scanning tunneling microscopy (ECSTM). Three dimensional nucleation and subsequent growth of copper crystals were found as the initial stage of copper deposition on HOPG. In the case of lower overpotential or lower concentration of Cu²⁺ , the bulk deposited copper layer tended to form smooth terraces, and grow at the edge of steps. The terraces were stable to some extent, which made it possible to be observed with atomic resolution. At a higher overpotential, the crystal size of copper were somehow smaller. …

The Reduction Of Oxygen To Hydrogen Peroxide In An Acidic Trickle Bed Cell Using Graphite Chip Cathode, Zhaoe Lu, Guanyong Zhang, Tiangeng Zhong, Guonu Fang

Journal of Electrochemistry

The authors investigated the electrochemical reduction of oxygen to hydrogen peroxide in 0.05 mol/L H₂SO₄ solution by the trickle bed electrode using graphite chip. The bed dimension was 14×5×0.6 cm. The current efficiency and the concentration of H₂O₂ in the catholyte were determined at various current strengths and various rates of adding the electrolyte. The proper current was 0.15 A. i.e. the current density was 2.1 mA/cm² vertical cross section area of the bed. The concentration of H₂O₂ reached 7×10^-3 mol/L with the current efficiency of 0.2. If the …

A Study Of The Electroplated Fe-Cr-Ni Alloy Microstructure, Donglin Li, Jianping Liu, Fangzhou Guo, Jianrong Hua

Journal of Electrochemistry

The microstructure of the electroplated Fe-Cr-Ni alloys from the mixed carboxylic acid solution containing Cr(Ⅲ) and additives were determined with XRD and SEM. Experimental results showed that, under the experimental condition, the phase component, structure of Cu base electroplated Fe-Cr-Ni alloys had a critical thickness, which was 11 μm and a critical Ni content, which was 32%. Organic additives, formic acid or polyethylene Glycol, mainly affected the surface, cross section morphology of the electroplated Fe-Cr-Ni alloys. Adding Mo to the electroplated Fe-Cr-Ni alloys led to remarkable corrosion resistance in concentrated HCl.

An Indirect Electrochemical Oxidation Of Toluene─Catalytic Effects Of Ag(Ⅰ) On Mn(Ⅱ)/Mn(Ⅲ) Couple Transition At Pt Electrode, Zhonghua Wang, Yunan Qu, Xingguo Yan, Qngmin Hua, Guacai Chen, Zhongquan Wang

Journal of Electrochemistry

The Catalytic effects of Ag(Ⅰ) on toluene oxidation by Mn(Ⅲ) as well as the anodic generation of Mn(Ⅲ) were investigated. The rates of toluene oxidation were first order with respect to both Ag(Ⅰ) and Mn(Ⅲ). Ag(Ⅱ) formed on the surface of the platinum anode when Ag(Ⅰ) was present in the anolyte, which catalyic the Mn(Ⅱ) to Mn(Ⅲ) in solution.

Preparation Techique Of Foamed Nickel By Electrodeposition, Xihua He, Ronghui Hu, Hanxi Yang, Zhengzhong Zuo

Journal of Electrochemistry

This paper describes the preparation technique and operation conditions for manufacturing foamed nickel by chemilcal pretreament, electrodeposition and heat treatment. The foamed nickel made in this method showed high porosity, uniformity and considerable strength and tenacity,applicable for various secondary battery electrodes.

Research On Molten Carbnate Fuel Cell, Naichao Li, Baolian Yi, Lianying Kong, Enjun Zhang, Huaxin Lin, Tianxi Qu, Yingcai Cheng

Journal of Electrochemistry

Cold-roll-milling has been evaluated as a technique for preparing porous LiAlO₂ matrices for use as a molten carbonate fuel cell electrolyte matrix. This technique produces reliable electrolyte structures with the following characteristics and advantages: ease of handling, uniform thickness, using nontoxic inorganic solvents, controlled pore size distribution, and ability to be impregnated with the alkali carbonate without fracrure.

The Molren Carbnatod Fuel Cell (MCFC) was assembled from sintered Ni electrodes and LiAlO₂ electrolyte matrix, the electrode area is 28 cm², the effect of operating conditions on cell performance was tested, it was found that the cell …

Study On The Manufacture Of Pt/C Gas-Diffusion Electrodes, Yonglin Ma

Journal of Electrochemistry

The various methods of manufacturing gas-diffusion electrodes are reviewed and a new method of preparing the Pt/C electrocatalyst and the gas-diffusion electrodes is explored in this paper. The electrochemical performance of resulting electrodes in concentrated phosphoric acid for oxygen reduction at 150℃ are compared with the commercial electrode which purched from Giner Inc. (U. S. A). The results show that the performance of the Pt/C electrodes which manufactured by the method in this paper has been greatly improved. Therefor, a fuel cell using such electrodes has high industrial value.

The Inhibition Of Amphipathic S- And N-Containing Compounds On Carbon Steel Corrosion, Wei Xing, Yibin Shan, Du Guo, Tianhog Lu, Shiquan Xi

Journal of Electrochemistry

Ordered monolayers of S- and N-containing amphipathic corrosion inhibitors were depoitod onto the surfaces of carbon steel electrode with super-molecular assembly technique. The effect of molecular aggregation of monolayers on carbon steel corrosion in 0.05 mol·cm^-3 H₂SO₄ and the mechanisms of these inhibitors were discussed in details. It was found that the transport of hydrated hydrogen ion to the surface of steel depends strongly on the inhibitor molecular aggregation in the monolayers.