Open Access. Powered by Scholars. Published by Universities.®

Chemistry Commons™

Open Access. Powered by Scholars. Published by Universities.®

Engineering Science and Materials

Institution
Keyword
Publication Year
Publication
Publication Type

Articles 1531 - 1560 of 1823

Full-Text Articles in Chemistry

The Applications Of Confocal Raman Micro-Spectroscopy For Study Of Practical Electrode Materials, Yong Yang, Wei Chu, Jun-Min Nan, Xun-Guang Chen, Zu-Geng Lin Feb 2001

The Applications Of Confocal Raman Micro-Spectroscopy For Study Of Practical Electrode Materials, Yong Yang, Wei Chu, Jun-Min Nan, Xun-Guang Chen, Zu-Geng Lin

Journal of Electrochemistry

Some recent research work about applications of confocal Raman micro spectroscopy for study of practical electrode materials carried out in our lab has been briefly introduced. The examples include study of electrochemical Li+ intercalation process, characterization of surface oxide film on AB5 type electrodes and passive film and pitting corrosion of Rebar electrodes.

Go to article

A Study On The Performance Of Matrix Prepared By Tape Cast And Its Molten Carbonate Fuel Cells (Mcfcs), Hua-Xin Lin, Bao-Lian Yi, Li Zhou, Chang-Qing He, Lian-Ying Kong, En-Jun Zhang Feb 2001

A Study On The Performance Of Matrix Prepared By Tape Cast And Its Molten Carbonate Fuel Cells (Mcfcs), Hua-Xin Lin, Bao-Lian Yi, Li Zhou, Chang-Qing He, Lian-Ying Kong, En-Jun Zhang

Journal of Electrochemistry

The matrix prepared with γ-LiAlO2 powder and by tape cast displayed higher ability of preventing from gas cross over and lower ohmic polarization. The voltages of the stack (three cells, 122 cm2) stacked with the matrix were 2.02 and 1.78 V at 200 and 246 mA/cm2, respectively, and the output power reached 53.4 W. The cell (28 cm 2) voltages were 0.85 and 0.75 V at 200 and 300 mA/cm2, respectively, and the output power was about 6.6 W. Compensating the shrinkage of matrix in stacking cells promoted the enhancement of the …

Go to article

Two-Dimensional Surface Raman Imaging Of A Roughened Iron Electrode In Saline Water, Pei-Gen Cao, Jian-Lin Yao, Jun-Wei Zheng, Bin Ren, Ren-Ao Gu, Zhong-Qun Tian Feb 2001

Two-Dimensional Surface Raman Imaging Of A Roughened Iron Electrode In Saline Water, Pei-Gen Cao, Jian-Lin Yao, Jun-Wei Zheng, Bin Ren, Ren-Ao Gu, Zhong-Qun Tian

Journal of Electrochemistry

The analysis of the composite and distribution of iron oxide due to pit corrosion in saline solutions (3.4% NaCl) is of great importance. Many electrochemical methods, XPS, and other photoelectronic techniques have been applied to this domain. Surface enhanced Raman scattering (SERS) spectroscopy can provide the vibrational information of surface species with high sensitivity and is very useful in the study of surface chemistry of iron. Notwithstanding, the application of SERS in iron corrosion is hampered for its SERS-inactivity. Efforts have been devoted to extend the use of SERS to the study of iron.

Go to article

How Can Direct Mthanol Fuel Cell Benefit From Carbonate Media, Lin Zhuang, Yang Wang, Jun-Tao Lu Feb 2001

How Can Direct Mthanol Fuel Cell Benefit From Carbonate Media, Lin Zhuang, Yang Wang, Jun-Tao Lu

Journal of Electrochemistry

The kinetics of methanol oxidation and oxygen reduction in 0.5 mol/L K2CO3 were compared with those in 0.5 mol/L H2SO 4. Experiments revealed that carbonate media could be more beneficial to direct methanol fuel cell(DMFC). Firstly, both electrode reactions show better performance in the carbonate than in the acid; secondly, materials other than noble metals become possible to be used as the anodic and cathodic catalysts; thirdly, the potential dectease caused by methanol crossover could be depressed by using metal oxide catalysts not stable in acid, such as MnO2.

Go to article

Synthesis Of Limn2O4-ΔClΔ Cathode Material By Like-Sol-Gel Methode, Zhao-Yong Chen, Yi He, Xing-Quan Liu, Zhi-Jie Li, Zuo-Long Yu Feb 2001

Synthesis Of Limn2O4-ΔClΔ Cathode Material By Like-Sol-Gel Methode, Zhao-Yong Chen, Yi He, Xing-Quan Liu, Zhi-Jie Li, Zuo-Long Yu

Journal of Electrochemistry

LiMn2O4-δClδ was synthesized by like sol gel methode, with calculated LiOH·H2O, Mn(No3)2⋅6H2O and LiCl·H2O, and made electrochemical test with these compounds as positive materials. Result demostrated that LiMn2O4-δClδ cathode material has exellent stability and nearly no capacity loss after reaching stability.

Go to article

In Situ Raman Spectroelectrochemical Characterization Of The Prussian Blue/Platinum Modified Electrode, Xiao-Wei Cao, Rong Wang, Gui-Hua Wang, Zong-Rang Zhang Feb 2001

In Situ Raman Spectroelectrochemical Characterization Of The Prussian Blue/Platinum Modified Electrode, Xiao-Wei Cao, Rong Wang, Gui-Hua Wang, Zong-Rang Zhang

Journal of Electrochemistry

Prussian Blue is known to be deposited electrochemically on the electrode surface, producing a dense redox active layer. Since the Prussian Blue modified electrode was first reported by Neff in 1978, different in situ spectroelectrochemical techniques have been widely used to investigate its electrochemical mechanism. But no research work related to the in situ Raman spectroscopic studies on it has been reported. In this paper we try to characterize the nature of thin Prussian Blue films on platinum substrates with in situ Raman spectroelectrochemical technique.

Go to article

Adsorption Behavior Of Co At The Ultrathin Rh And Pt Film Electrodes, Yong Xie, Xiao-Qin Li, Bin Ren, Zhong-Qun Tian Feb 2001

Adsorption Behavior Of Co At The Ultrathin Rh And Pt Film Electrodes, Yong Xie, Xiao-Qin Li, Bin Ren, Zhong-Qun Tian

Journal of Electrochemistry

Pt group metals have been widely used in catalysis such as hydrogenation of organic compounds and the oxidation of carbon monoxide. The information about CO adsorption on the Pt group surfaces and the influence of other surface species, such as hydrogen and CO2 will be greatly helpful to elucidate the adsorption behavior of CO on Pt group metal surfaces and get a deeper understanding of catalytic mechanisms of Pt group metals. Surface enhanced Raman spectroscopy (SERS) has been becoming an increasingly important means to characterize the electrochemical metal solution interface over the past two decades. Our laboratory has successfully …

Go to article

Adsorption And Oxidation Of Ethanol On Nm-Pt/Gc Electrode Ii. Eqcm And In-Situ Ftir Spectroscopic Studies In Acid Media, Guo-Liang Chen, Sheng-Pei Chen, Zhi-You Zhou, Chun-Hua Zhen, Shi-Gang Sun Feb 2001

Adsorption And Oxidation Of Ethanol On Nm-Pt/Gc Electrode Ii. Eqcm And In-Situ Ftir Spectroscopic Studies In Acid Media, Guo-Liang Chen, Sheng-Pei Chen, Zhi-You Zhou, Chun-Hua Zhen, Shi-Gang Sun

Journal of Electrochemistry

The adsorption and oxidation of ethanol on nm Pt/GC electrode in acid solutions containing 0.1 mol·L -1 H2SO4 +0.1 mol·L -1 CH3CH2OH was investigated by using cyclic voltammetry, EQCM and in situ FTIR spectroscopy. The experimental results demonstrated that the oxidation of CH3CH2OH is closely relaed to solution acidity and oxygen species on electrode surface; CH3CH2OH was oxidized on nm Pt/GC electrode in acidic media via a dual path reaction mechanism, i.e . CH3CH2OH may be oxidized into CO2 through …

Go to article

The Photoelectrochemistry Of Tio2-Polyaniline Composite Film, Huai-Guo Huang, Zhi-Xin Zheng, Jin Luo, Hong-Ping Zhang, Ling-Ling Wu, Zhong-Hua Lin Feb 2001

The Photoelectrochemistry Of Tio2-Polyaniline Composite Film, Huai-Guo Huang, Zhi-Xin Zheng, Jin Luo, Hong-Ping Zhang, Ling-Ling Wu, Zhong-Hua Lin

Journal of Electrochemistry

A TiO2 and polyaniline (PANI) composite film was obtained by electrochemical methods. The SEM image of the composite film showed that the PANI film is almost completely covered with TiO2 efficiency. The spectra of photocurrent for the TiO2-PANI composite film were different from these of TiO2 film photosensitized by PANI. The bandgap energy of TiO2 film on partially oxidized PANI film was determined as 3.0 eV by the threshold energy of photocurrent band for TiO2. The spectra of photocurrent for partially oxidized PANI film electrode suggested that it has the characteristics of …

Go to article

Catalytic Effect Of Cl- On Electrodeposition Of Binary Zinc Alloys With Iron Group Metals, Ren-He Yin, Zheng-Hua Fang, Wei-Min Cao, A.Za Karia, Rong-Ming Zhou Feb 2001

Catalytic Effect Of Cl- On Electrodeposition Of Binary Zinc Alloys With Iron Group Metals, Ren-He Yin, Zheng-Hua Fang, Wei-Min Cao, A.Za Karia, Rong-Ming Zhou

Journal of Electrochemistry

Zinc iron group metal alloys were deposited under coulostatic (10C⋅cm-2) at 40 ℃ chloride baths. The deposited alloys were quantitatively analyzed by Atomic Absorption Spectrometry. The current efficiency, percent content and partial polarization curves were obtained by the results. The morphology of the deposits was observed by means of Scanning Electron Microscopy(SEM). We observe that the electrodeposition of zinc iron group metal alloys is one of the best known examples of anomalous codeposition. We found the catalytic effect of Cl- on the electrodeposition behavior of iron group metal. Overpotential of iron group metal droped abruptly at high …

Go to article

Electrochemical Hydrogen Storage Properties Of Carbon Nanotubes, Xue Qin, Xue-Ping Gao, Feng Wu, Hong Liu, Ying Lan, Hua-Tang Yuan, De-Ying Song, Pan-Wen Shen Nov 2000

Electrochemical Hydrogen Storage Properties Of Carbon Nanotubes, Xue Qin, Xue-Ping Gao, Feng Wu, Hong Liu, Ying Lan, Hua-Tang Yuan, De-Ying Song, Pan-Wen Shen

Journal of Electrochemistry

The electrochemical properties of carbon nanotubes (CNTs) electrode have been investigated in this paper. The high discharge capacity of 200 mAh·g-1 was measured for the CNTs Ni electrode at a discharge density of 200 mAh·g-1 . CNTs-Ni electrode, the high electrochemical activity and the long cycle life were observed. The electrochemical mechanism of hydrogen adsorption and oxidation at the CNTs Ni electrode was studied by cyclic voltammertry method.

Go to article

Template Synthesis Of Nano-Structured Electrode Materials And Its Electrochemical Performance, Jian Zhao, Quan-Yong Gao, Yong Yang, Zu-Geng Lin Nov 2000

Template Synthesis Of Nano-Structured Electrode Materials And Its Electrochemical Performance, Jian Zhao, Quan-Yong Gao, Yong Yang, Zu-Geng Lin

Journal of Electrochemistry

In this letter, various nano structured materials such as spinel LiMn2O4 nanotubes/nanowires and carbon nanotubes have been prepared by using porous alumina template. The prepared template and materials have been characterized by AFM and TEM techniques. It is shown that size of the nanotubes can be conveniently controlled by using template method. Some preliminary results of cyclic voltammetry about nano structured LiMn2O4 are also reported.

Go to article

A Study Of Monitoring Corrosion Of Metal Via An Optic Waveguide Sensing Method, Xue-Ming Li, Wei-Ming Chen, Shang-Lian Huang, Na Zhang, Zong-Qing Huang Nov 2000

A Study Of Monitoring Corrosion Of Metal Via An Optic Waveguide Sensing Method, Xue-Ming Li, Wei-Ming Chen, Shang-Lian Huang, Na Zhang, Zong-Qing Huang

Journal of Electrochemistry

An optical wave guide sensing method was proposed for monitoring corrosion of metal in outdoors steel structures. Replacing the cladding of wave-guide with metal film in a particular location, the method takes the metal film as the corrosion sensitive film. The experiment of waveguide sensor was carried out on a 721 colorimetric vessel, with which the soution is held in itself and the light is propagated in its sidewall. A Fe-C alloy film was electroplated onto the inner sied of vessel to form the corrosion sensitive film. The structure of the Fe-C alloy film was studied by XRD, EDX and …

Go to article

The Study Of Pretreatment For The Determination Of The Conventional Anion In Sea Water By Ic——The Method Of Electrolysing Argentine Electrode, Lei Guo, Wei Yang, Rong-Zong Hu Nov 2000

The Study Of Pretreatment For The Determination Of The Conventional Anion In Sea Water By Ic——The Method Of Electrolysing Argentine Electrode, Lei Guo, Wei Yang, Rong-Zong Hu

Journal of Electrochemistry

The method of pretreatment to determine trace amounts of Br-, NO3- and SO42- in sea water by ion chromatography was proposed, by which the electrolysing argentine electrode was used to minimize the disturbance of Cl-. The results indicate that the method is simple, convenient, quick and efficient with recovery rates over 95 percent.

Go to article

Study On Electrodeposition Of Ingaas Thin Film, Yu-Chun Li, Xi-Lian Wang, Jing-Ke Han, Ai-Zhen Han, Yuan-Kai Gao, Zhi-Wei Yang Nov 2000

Study On Electrodeposition Of Ingaas Thin Film, Yu-Chun Li, Xi-Lian Wang, Jing-Ke Han, Ai-Zhen Han, Yuan-Kai Gao, Zhi-Wei Yang

Journal of Electrochemistry

The principle and the experimental method of the electrodeposition are discribed in detail in this paper. InGaAs thin film was prepared by using optimized electrodeposited conditions. The radiative wave length of the film was between 1.3～1.5 μm, the composition of the film was analyzed by energy spectrometer and the transmission spectrum of the film was measured by spectrophotometer and monochromator. The V-I chractristic of the conductive type and the topography of the InxGa1-xAs film were also studied.

Go to article

The Memory Effect Of Mh-Ni Battery, De-Ming Xie, Jian-Ming Wang, Jian-Qing Zhang, Chu-Nan Cao Nov 2000

The Memory Effect Of Mh-Ni Battery, De-Ming Xie, Jian-Ming Wang, Jian-Qing Zhang, Chu-Nan Cao

Journal of Electrochemistry

The memory effect of MH-Ni battery was investigated. The depth of discharge, discharge rate and cycle number influence the memory effect greatly. A few completely full charge/discharge cycles could eliminate it. The existence of the memory effect had nothing to do with zinc element. During the course of life cycling at low DOD (degree of discharge), the smaller the discharge current was, the lower was the maximum charge voltage. In addition, discharge voltage and discharge capacity drop fast at the beginning, gradually leveled off at about a value. If the discharge current was increased, the discharge capacity was obviously less …

Go to article

The Development Of Carbon Monoxide Tolerant Catalysts For Proton-Exchange Membrane Fuel Cell, Zhong-Jun Hou, Hong-Mei Yu, Bao-Lian Yi, Ming Han Nov 2000

The Development Of Carbon Monoxide Tolerant Catalysts For Proton-Exchange Membrane Fuel Cell, Zhong-Jun Hou, Hong-Mei Yu, Bao-Lian Yi, Ming Han

Journal of Electrochemistry

High over-potential of proton exchange membrane fuel cell (PEMFC) anode caused by carbon monnoxide poisoning when reformate or methanol is used as fuel is main obstacle to the high performance of PEMFCs. Using carbon monoxide tolerant catalysts is the most hopeful way to solve the CO problem. The CO poisoning problem is reviewed briefly in this paper, and the development of CO tolerant catalysts is introduced in details, including electrocatalysts activity, preparation method and mechanism of tolerance to CO.Mo and W can improve catalysts' CO tolerance. Multi-component catalysts are expected to be more tolerant to CO.

Go to article

Investigation Of A Complex Lithium Cobalt Nickel Oxide As Lithium Ion Battery Cathode Materials Prepared By A New Citrate Sol-Gel Method, Jing-Li Han, Qing-Guo Liu Nov 2000

Investigation Of A Complex Lithium Cobalt Nickel Oxide As Lithium Ion Battery Cathode Materials Prepared By A New Citrate Sol-Gel Method, Jing-Li Han, Qing-Guo Liu

Journal of Electrochemistry

The synthesis and electrochemical characteristics of lithium cobalt nickel oxide as cathode materials for rechargeable lithium batteries were investigated. It was clarified from these investigations that lithium cobalt nickel oxide has been produced from basic cobalt carbonate,basic nickel carbonate, lithium carbonate, and citrate. LiNi0.8Co 0.2O2 prepared under the stream of oxygen gas showed a higher cycling capacity of (～190 mAh·g-1).

Go to article

A Study Of The Adsorption Behaviors On The Surface Of Gold Electrode By In-Situ Electrochemical Raman Spectroscopy, Xia-Qin Wu, Xiao-Wei Cao, Zhe-Su Wang, Xiao-Yun Meng, Zong-Rang Zhang Nov 2000

A Study Of The Adsorption Behaviors On The Surface Of Gold Electrode By In-Situ Electrochemical Raman Spectroscopy, Xia-Qin Wu, Xiao-Wei Cao, Zhe-Su Wang, Xiao-Yun Meng, Zong-Rang Zhang

Journal of Electrochemistry

The results of in-situ measurements with Raman spectroelectrochemical thchnique on bare gold electrode and adenine modified gold electrode were reported. The adsorption behaviors of adenine and superoxide dismutase (SOD) and their interactions with gold electrode were analyed. The mechanism of promoted electron transfer process of SOD in the presence of adenine at gold electrode surface is discussed.

Go to article

Effect Of High Concentration Lithium Bromide Solution On Electrochemical Behavior Of Low Alloy Steel At High Temperature, Jian-Wei Guo, Cheng-Hao Liang Nov 2000

Effect Of High Concentration Lithium Bromide Solution On Electrochemical Behavior Of Low Alloy Steel At High Temperature, Jian-Wei Guo, Cheng-Hao Liang

Journal of Electrochemistry

By electrochemical measurements and weight loss experiments, the effect of MoO42- on low alloy steel's electrochemical behaviors was investigated at high temperature in 55%LiBr+0.07 mol/L LiOH solution. The results showed that MoO42-, as an anodic inhibitor, formed passive film rapidly and impeded both anodic and cathodic procedures. Moreover, Na2MoO4 prevented corrosion effectively in 55%LiBr+0.07 mol/L LiOH solution when its concentration is more than 200 mg/L. The pitting potential increased accompanying to the arising of Na2MoO4 concentration. Some elements of alloy strengthened resistance to corrosion, shch as chromium and nickel, …

Go to article

Studies Of Adsorption And Oxidation Of Ethanol On Nm-Pt/Gc Electrode——I. Cyclic Voltammograms And In-Situ Ftir Spectroscopy In Alkaline Media, Guo-Lian Chen, Shi-Gang Sun, Sheng-Pei Chen, Zhi-You Zhou Nov 2000

Studies Of Adsorption And Oxidation Of Ethanol On Nm-Pt/Gc Electrode——I. Cyclic Voltammograms And In-Situ Ftir Spectroscopy In Alkaline Media, Guo-Lian Chen, Shi-Gang Sun, Sheng-Pei Chen, Zhi-You Zhou

Journal of Electrochemistry

The electro-oxidation of ethanol on nm-Pt/GC electrode in alkaline solutions containing 0.02 mol·L-1 NaOH+0.1 mol·L-1 CH3CH2OH was investigated by using cyclic voltammetry and in-situ FTIR spectroscopy. The experimental results demonstrated that the main product of ethanol oxidation is CH3COO-, only very small amount of CH 3CHO has been determined simultaneously. In contrast with the dual path reaction mechanism for the oxidation of ethanol in acid media, the oxidation of ethanol in alkaline media didn't pass through the dissociative adsorption, and no adsorbed species could be determined even using a …

Go to article

The Effect Of Cerium On The Anodic Behavior Of Pb-Ca-Sn Alloy In Sulfuric Acid Solution, Hou-Tian Liu, Jiong Yang, Hai-He Liang, Ji-Hua Zhuang, Wei-Fang Zhou Aug 2000

The Effect Of Cerium On The Anodic Behavior Of Pb-Ca-Sn Alloy In Sulfuric Acid Solution, Hou-Tian Liu, Jiong Yang, Hai-He Liang, Ji-Hua Zhuang, Wei-Fang Zhou

Journal of Electrochemistry

The cyclic voltammograms for Pb - 0.5 at% Ca - 1.5 at% Sn and Pb - 0.5 at% Ca - 1.5 at% Sn containing a certain amount of cerium in 4.5 mol·dm-3 H2SO4 at 20℃ were measured between 0.6 V and 1.4 V(vs. Hg/Hg2SO4). The growth rate of the anodic Pb(Ⅱ) films formed on the mentioned alloy electrodes at 0.9 V in the same sulfuric acid medium was investigated using the Linear Sweep Voltammetry. The variation with electrode potential of the real part of the impedence (Z’) for the anodic Pb(Ⅱ) films …

Go to article

The Lineal Polarization Method For Corrosion Rate Measurement Of Reinforcing Bar Of Concrete In Situ, Ai-Ling Du, Wen-Tao Hou, He-Ming Zhang, Jian-Qun Luo Aug 2000

The Lineal Polarization Method For Corrosion Rate Measurement Of Reinforcing Bar Of Concrete In Situ, Ai-Ling Du, Wen-Tao Hou, He-Ming Zhang, Jian-Qun Luo

Journal of Electrochemistry

A linear polarization method was applied to measure corrosion rate of reinforcing bar of concrete in situ. Generally in the experiment, the area and shape of the reinforcing bar as a working electrode can be changed and adjusted according to our needs. But polarization area cannot be defined when reinforcing bar is polarized in situ, so that a real Rp can't be obtained. Thus the purpose of present work is to improve the measurement system. We used the double-ring auxiliary electrodes made by ourselves. The size of the double-ring auxiliary electrodes was adjusted repeatedly until the real polarization area …

Go to article

Cathodic Indirect Oxidation Of Organic Compounds(Ⅱ)——Cathodic Indirect Epoxidation Of Olefine, Xue-Ying Zhang, Bao-Qiu Cui, Deng-Ping Gu, Wei Li Aug 2000

Cathodic Indirect Oxidation Of Organic Compounds(Ⅱ)——Cathodic Indirect Epoxidation Of Olefine, Xue-Ying Zhang, Bao-Qiu Cui, Deng-Ping Gu, Wei Li

Journal of Electrochemistry

We described a novel cathodic indirect epoxidation system in which O2 was first cathodically reduced to H2O2. Then VO(acac)2 was oxidized by H2O2 homogeneously to VO(acac)2OOH which was used to epoxidize some olefine such as maleic, fumaric and crotonic acids. Many affecting factors on the current efficiency were optimized. The research will contribute to the developments of organic electrosynthesis.

Go to article

The Electro-Catalytic Oxidation Of Hcooh On Electrodeposited Pd Electrode, Quan Zhou, Cun-Zhong Zhang, Xiao-Lin Lu, Zhong-Da Wu Aug 2000

The Electro-Catalytic Oxidation Of Hcooh On Electrodeposited Pd Electrode, Quan Zhou, Cun-Zhong Zhang, Xiao-Lin Lu, Zhong-Da Wu

Journal of Electrochemistry

The coherent electroplates were prepared by electro depositing Pd on supporting materials glassy carbon. The surface morphology of the electrodes was examined by SEM. The electro oxidation of HCOOH in HClO4 solution was investigated by using cyclic voltammetry. The results show that the deposited conditions in the preparation of electrodes by electro depositing Pd affect the electrodes electro catalytic activity to the oxidation of HCOOH. The platinized Pd electrode on GC substrates using large current density is of higher catalytic activity to the oxidation of HCOOH than Pd electrode. The electro catalytic activity of PdO formed on the Pd …

Go to article

The Study On Lithiated Titanium Composite Oxides As Negative Electrode For Lithium-Ion Battery, Xiao-Yan Yang, Shou-Nan Hua, Shu-Yong Zhang Aug 2000

The Study On Lithiated Titanium Composite Oxides As Negative Electrode For Lithium-Ion Battery, Xiao-Yan Yang, Shou-Nan Hua, Shu-Yong Zhang

Journal of Electrochemistry

Lithiated titanium composite oxides Li4Ti5O12 were prepared from Li2CO3 and TiO2. The XRD results of this composite oxides indicated that the compound had a spinel structure. The electrochemical behavior of lithiated titanium composite oxides was examined. The results showed that this material had an excellent cyclic capability and reversibility for lithium insertion, and had high specific capacity: the initial discharge capacity was 300 mAh·g-1 , and the reversible capacity was 100 mAh·g-1 . The discharge plateau (about 1.5 V) and the charge plateau (about 1.6 V) were very …

Go to article

Studies Of The LialYNi1-YO2 As Cathode Materials For Rechargeable Lithium Ion Batteries, Xiao-Gan Li, Wei-Hua Qiu, Chuan-Gang Lin, Qing-Guo Liu Aug 2000

Studies Of The LialYNi1-YO2 As Cathode Materials For Rechargeable Lithium Ion Batteries, Xiao-Gan Li, Wei-Hua Qiu, Chuan-Gang Lin, Qing-Guo Liu

Journal of Electrochemistry

In this paper, we have synthesized series of single-phase LiAlyNi1-yO2 (differentive in value-y) by solid reaction. Through examining their electrothemical properties, found that, under a proper sintering condition, LixAl0.25Ni0.75O2 solution for cathode materials of rechargeable lithium ion batteries showed more pleasing properties in overcharge-resist and cycling life (vs LiNiO2). When x>1, the capacity can be kept 125mAh/g after 30 cycles under higher charged/discharged voltages ranging from 3.0 V to 4.8 V, whereas that of pure LiNiO2 has only 61 nAh/g after 25 cycles. The …

Go to article

Electrochemical Characteristics Of Sb Irreversibly Adsorbed On Pt(100), Pt(110), Pt(111) And Pt(320) Electrodes, Yi-Yun Yang, Zhi-You Zhou, Qi-Hui Wu, Shi-Gang Sun Aug 2000

Electrochemical Characteristics Of Sb Irreversibly Adsorbed On Pt(100), Pt(110), Pt(111) And Pt(320) Electrodes, Yi-Yun Yang, Zhi-You Zhou, Qi-Hui Wu, Shi-Gang Sun

Journal of Electrochemistry

The electrochemical behaviors of irreversibly adsorbed antimony on Pt(100), Pt(110), Pt(111) and Pt(320) were studied by using cyclic voltammetry. The results revealeds that the Sb adatoms are stable on Pt(100), Pt(110), Pt(111) and on Pt(320) when electrode potentials are below 0.45 V(SCE) and 0.40 V, respectively. It was demonstrated that various coverages of Sb ad can be conveniently obtained by controlling the number of potential cycling and varying the upper limit of potential scan. The electrochemical behaviors of irreversibly adsorbed antimony varied with the surface atomic arrangement of Pt single crystal electrodes. Based on quantitative results of the relationship between …

Go to article

A Study On Stochastic Resonance For The Process Of Active-Passive Transition Of Iron In Sulfuric Acid, Hong-Bo Ding, Bao-Yun Xia, Chun-Sheng Yin, Zhong-Xiao Pan, Renato Seeber Aug 2000

A Study On Stochastic Resonance For The Process Of Active-Passive Transition Of Iron In Sulfuric Acid, Hong-Bo Ding, Bao-Yun Xia, Chun-Sheng Yin, Zhong-Xiao Pan, Renato Seeber

Journal of Electrochemistry

The bistable characteristics of the process of active passive transition of iron in sulfuric acid was described and the stochastic resonance phenomenon in the process was simulated.

Go to article

Corrosion Behavior Of Reinforcing Steel In Concrete, Rong-Gui Du, Rong-Gang Hu, Zu-De Feng, Jiang-Guang Tan, Chang-Jian Lin Aug 2000

Corrosion Behavior Of Reinforcing Steel In Concrete, Rong-Gui Du, Rong-Gang Hu, Zu-De Feng, Jiang-Guang Tan, Chang-Jian Lin

Journal of Electrochemistry

The corrosion behavior of reinforcing steel in concrete in chloride free and chloride contaminated simulated concrete solutions was studied by electrochemical technique. The results showed that the reinforcing steel exhitibted different corrosion characteristics in the different solutons. In general, the steel in concrete was protected in the test solutions with no salt or the lower concentration of NaCl. When the concentration of NaCl is larger than 70%, however, the corrosion behavior of the steel varied considerably, and the corrosion rate increased as pH fell and the concentration of Cl- increased.

Go to article

First Prev Next Last