Chemistry Commons^™

Preparation And Characterization Of Casno3 Anode Material For Lithium Ion Batteries, Ran Sun, Zi-Geng Liu, Ya-Qi Jiang

Journal of Electrochemistry

In this study the precursor CaSn(OH)₆ was prepared via a hydrothermal process, and its composition, surface feature and phase-transition were characterized by XRD, SEM and DSC-TGA. The shapes of CaSn(OH)₆ crystals were effectively controlled by adjusting the volumn ratio of H₂O and CH₃CH₂OH solvents. Perovskite CaSnO₃ could be obtained by calcination of CaSn(OH)₆ at 800 ℃. The reversible capacity of 334.4 mAh/g with good cycling stability could be achieved with the CaSnO₃ electrode.

Preparation And Characterization Of The Lani0.6Fe0.4O3-δ Cathode For Intermediate Temperature Solid Oxide Fuel Cell, Hang Liu, Bo Huang, Xin-Jian Zhu

Journal of Electrochemistry

The LaNi_0.6Fe_0.4O_3-δ as cathode material for intermediate temperature solid oxide fuel cell was prepared using a combustion synthesis technique. The X-ray diffraction (XRD) pattern showed that the single-phase LaNi_0.6Fe_0.4O_3-δ perovskite could be obtained after heat treatment at 600°C. The TEM and SEM images of the synthesized powders revealed that the grains were 50-100nm. According to the electrochemical impedance spectra (EIS), the polarization resistance of the symmetric cell LaNi_0.6Fe_0.4O_3-δ/ScSZ/LaNi_0.6Fe_0.4O_3-δ sintered at 1050°C was the smallest (0.70Ω·cm², 0.27Ω·cm^{2 …}

Dynamic Modeling And Characteristic Analysis Of Proton Exchange Membrane Fuel Cell, Qiu-Hong Jia, Ming Han, Bin Deng, Cai-Zhi Zhang

Journal of Electrochemistry

In this paper, a dynamic model of PEMFC is developed to estimate the dynamic performance of PEMFC by analyzing in detail the influence factors of voltage of PEMFC including various losses. The partial pressure of hydrogen and oxygen is obtained using the differential form of the ideal-gas equation in this model. The steady-state model is obtained by setting reasonable parameter values. The simulation results and experimental results have good consistency, which shows that the simulation model is correct, reasonable and effective. It analyzed the dynamic response characteristics of the output voltage and the partial pressure of hydrogen in condition of …

Preparation And Capacitance Characteristics Of Nickel Oxide Electrode With Mesh-Like Structure, Hui Xu, Zhen-Jun Peng, Dong-Hong Guo, Jun-Ling Li

Journal of Electrochemistry

The mesh-like structure of NiO electrode was obtained by first preparing the precursors via hydrothermal process using nickel sulfate and carbamide as reactants, sodium hexametaphosphate as a surfactant, and followed by calcination of the precursors at 400 ℃. The structure, morphology and capacitance characteristics of NiO electrode were characterized by XRD, SEM and constant current charge-discharge testing techniques. The effects of hydrothermal temperatures on the electrochemical properties of NiO electrode were investigated. The results showed that the better property of nickel oxide was obtained when the mole ratio of nickel to urea was 1:4 and the hydrothermal temperature was 140℃. …

Electrochemical Performance Of Tin Dioxide/Carbon Xerogel Composites As Anode Materials For Lithium-Ion Batteries, Xiao-Jing Liu, Lin-Lin Qin, Yi-Ning Shi, Ming-Sen Zheng, Quan-Feng Dong

Journal of Electrochemistry

The tin dioxide/carbon xerogel composites were synthesized by using vacuum infiltration method. Structural characterization and morphology of the composites were investigated by using XRD, TEM and SEM techniques. BET test was performed to determine the pore size distributions of carbon xerogels and the composites. The results showed that the nano-sized SnO₂ particles (5~10 nm) were encapsulated in the pores of carbon xerogels. During the electrochemical tests the SnO₂ in the composites exhibited capacity retention of 61.9% after 100 cycles of charge-discharge tests at 100 mA/g.

Study On The Fluorescent Carbon Nanodots With Electrochemical Methods, Bao-Ping Qi, Yan-Min Long, Lei Bao, Cui Liu, Zhi-Ling Zhang, Dai-Wen Pang

Journal of Electrochemistry

Carbon nanodots are a new class of fluorescent nanoparticles with a carbon-based core, which possess wavelength-tunable luminescence, high photostability, resistance to photobleaching, water-solubility, and ease of bioconjugation. Owing to their attractive merits, carbon nanodots like other carbon nanomaterials such as fullerene, carbon nanotubes and graphene, have attracted much attention. In addition, carbon nanodots can be inexpensively produced by electrochemical methods with simple post-processing under mild conditions. Electrochemical approaches have unique advantages in the analysis of surface structures and luminescence mechanism of materials. In this review, recent advances in electrochemical methods used for the synthesis and luminescence mechanism of fluorescent carbon …

Study On The Electrochemical Behaviors Of Gc Electrode Modified With Carbon Nanotube-Polyelectrolytes And Its Application For Rutin Detection, Liang Hua, Xia-Qin Wu, Rong Wang

Journal of Electrochemistry

The electrochemical behaviors of rutin and ascorbic acid at single-wall carbon nanotube and polyelectrolytes (dimethyl-diallylammonium chloride, PDDA) film modified glassy carbon electrode was investigated. The cyclic voltammetric results showed that electron transfer of rutin at PDDA/SWCNTs/GC modified electrode is an adsorption-controlled process. The separation of oxidation peak potentials of rutin and ascorbic acid was more than 200 mV. The rutin concentration in the presence of AA were detected by differential pulse voltammetry (DPV). The experimental results indicated that the PDDA/SWCNTs/GC modified electrode can be used for the detection of rutin in the presence of high concentration of AA. The DPV …

Study On Residual Powders Of Lithium-Ion Batteries With Different Voltages After Explosion, He Li, Zhi-Kui Chen, Ji-Na Cao, Guang-Chuan Liang

Journal of Electrochemistry

The residual powders of lithium-ion batteries at different voltages after explosion were obtained by using the battery impact testing machine. And these powders have been investigated by weighing, water solution and X-ray diffraction (XRD). The results showed that the integrity status of copper current collector and weight of residual powders decreased gradually with increasing of battery voltage, rising of burning temperature and releasing of burning duration time. The residual powders could be separated to insoluble powders and soluble powders by the water solution. The proportion of the insoluble powders is more (about 90%) including C, Co and CoO, while the …

Effects Of Graphene On Electrochemical Behaviors Of Ni(Oh)2 As Supercapacitor Material, Zhen-Zhen Zhao, Wen-Bin Ni, Neng-Yue Gao, Hong-Bo Wang, Jian-Wei Zhao

Journal of Electrochemistry

The enhanced electrochemical properties of Ni(OH)₂ by the oxidation defected graphene were studied by both experimental method and theoretical calculation. The composite material of nano-Ni(OH)₂/graphene was prepared by potentiostatic deposition on the graphene substrate. Observed by TEM, the Ni(OH)₂ nanoparticles were well dispersed on the graphene substrate with the diameter of 5.0±0.5 nm. The capacitance of the system measured by the electrochemical test was 1928 F·g^-1. As indicated by the theoretical calculations, the composite material becomes conductive since Ni(OH)₂ is combined with surface functional groups of the graphene through the strong chemical interaction. …

Synthesis Of Limnpo4/C Used As Cathode Material For Lithium Ion Batteries, Xin Yang, Xue-Wu Liu, Gui-Chang Liu, Zhi-Cong Shi, Xin Li, Guo-Hua Chen

Journal of Electrochemistry

The LiMnPO₄/C composites were prepared using a solid-state reaction with addition of the resorcinol formaldehyde resin as the carbon source. The effects of reaction temperature and time on the crystal structure, morphology and electrochemical properties of the LiMnPO₄/C composites were investigated. The results show that the best performance was achieved with the LiMnPO₄/C composites synthesized at 600 ^oC for 12 h which had the particle sizes about 100~200 nm. The initial discharge capacities were 121.6 mAh·g^-1 at 0.02C, 110 mAh·g^-1 at 0.1C and more than 60 mAh·g^-1 at 1C. An …

Synthesis And Electrochemical Behaviors Of Li2Coxmn1-XSio4 As A Cathode Material For Lithium-Ion Batteries, Lin Wang, Dong-Ping Lv, Yong Yang

Journal of Electrochemistry

We have successfully synthesized Li₂Co_xMn_1-xSiO₄/C (x=0, 0.1, 0.3, 0.5, 1)/C composites using hydrothermal assisted sol-gel process and ball-milling method. The results of X-ray diffraction show that the solid solutions of Li₂Co_xMn_1-xSiO₄ can be achieved when x≤0.3. The initial capacities increase from 70 mAh·g^-1 of Li₂MnSiO₄/C to 105 mAh·g^-1 of Li₂Co_0.3Mn_0.7SiO₄/C. Cyclic Voltammetry (CV) curves show that the replacement of Mn with Co can reduce the electrochemical polarization, making the insertion-extraction reaction …

Electrelectrochemical Performances Of C-Coating And Co-Doping Lifepo4, Ying Bai, Jue-Ming Yang, Chun-Bo Qing, Wei-Feng Zhang

Journal of Electrochemistry

Phospho-olivine LiFePO₄ cathode materials were prepared by hydrothermal reaction at 200 ^oC. Sucrose was added as C-coating resource and Co was doped into the crystal lattice of LiFePO₄. In order to investigate the improvements in the electrochemical properties of Co-doped LiFePO₄, three samples, LiFePO₄, C-coated LiFePO₄ and C-coating-Co-doped LiFePO₄, were synthesized under the same preparation conditions. Charge/discharge studies reveal that the Co-doped LiFePO₄/C composite annealed at 400 ^oC exhibits marked improvement of specific capacity by diminishing the particle sizes and enhancement in the degree of crystallinity. …

Miniature Mass Spectrometry: Rf Amplitude Control System Design, Matthew Allen Kirleis

Purdue Polytechnic Masters Theses

This thesis covers the methods used to construct and characterize a custom digital RF amplitude control system. Many types of mass spectrometers exist, but few have been miniaturized as much as the Mini instruments developed at Purdue University. The goal of this research was to improve upon an earlier amplitude control system consisting of analog circuits first implemented in the Mini 11.5 mass spectrometer developed at Purdue University.

A custom set of control and data acquisition electronics were developed for testing the digital and analog control systems in a Mini 11.5 mass spectrometer chassis. A MATLAB Simulink simulation was done …

Research Progress In Orthosilicates As Cathode Materials For Li-Ion Batteries, Dong-Ping Lv, Lin Wang, Yong Yang

Journal of Electrochemistry

Rechargeable Li-ion batteries fulfilling high-energy density, high safety, environmental friendliness, and low cost are demanded urgently for energy storage systems. Besides the structure stability arising from the strong Si-O covalent bond, environmental benignancy and low cost from the characteristics of Fe, Mn, Si elementals, orthosilicates (Li₂MSiO₄) show promising prospect to meet the demand of high-energy density for its two available Li+ per formula unit. Motivated by these significant advantages, Li₂MSiO₄ have been intensively investigated in the past few years. In the present work, we gave a review on the progress of orthosilicate research …

Effect Of Pore Size On Pseudo-Capacitive Performance Of Nio In The Mixed Electrolyte Of Koh And Hexacyanoferrate, Wen Wu, Meng-Yan Hou, Dan-Dan Zhou, Yong-Yao Xia

Journal of Electrochemistry

In this paper, five kinds of NiO samples with different pore size distributions were synthesized .The electrochemical capacitance of the samples were characterized in 3 mol/L KOH solution with and without hexacyanoferrate addition. Electrochemical test results indicated the NiO sample with an optimum pore size of about 15 nm shows high Coulombic efficiency of the N₄(NiO) electrode as the redox reaction of hexacyanoferrate ions would be limited in the pore, thus prevent ion diffusion into the bulk electrolyte solution .

Synthesis And Catalytic Property Of Flaked Spindle-Like Cuo Nanocrystals, Jian-Feng Fan, Li-Qing Li, Yu-Feng Huang, Lou-Zhen Fan

Journal of Electrochemistry

A simple and efficient electrochemical route was developed for the synthesis of flaked spindle-like CuO nanocrystals using aqueous electrolyte and Cu sacrificial anode (graphite as the cathode) in an undivided cell at a constant potential mode under room temperature. The morphologies, structure and component of CuO nanocrystals obtained were characterized by SEM, XRD, respectively. Flaked spindle-like CuO nanocrystals were successfully used to modify a GC electrode to detect H₂O₂ with cyclic voltammetry (CV) and amperometric (AC).The results showed that products were pure monoclinic CuO nanocrystals. The linear range for the determination of hydrogen peroxide is from 1.0 …

Investigation Of Supercapacitors Based On Polyvinyl Alcohol Hydrogel-Polymer Electrolyte, Kai-Qing Xu, Le-Qing Fan, Ji-Huai Wu, Qing Leng, Xin Zhong, Jian-Ming Lin, Miao-Liang Huang, Zhang Lan

Journal of Electrochemistry

For the first time, the supercapacitor based on the hydrogel-polymer electrolyte which consisted of the cross-linking of polyvinyl alcohol-glutaraldehyde (PVA-GA) using 2-acrylamido-2-methyl propane sulfonic acid (AMPS) as solicitation reagent was assembled. The gel polymer electrolyte was characterized by FTIR and AC impedance. The maximum ionic conductivity is 1.23 mS/cm at room temperature. The electrochemical properties of the supercapacitor were investigated by cyclic voltammetry, AC impedance spectra and constant current charge-discharge curve. The results show that the specific capacitance reachs 139 F/g with AMPS of 1.0 g and 0.05 mL of 5 %(by mass) GA. And the specific capacitance still retained …

Detection Of Acute Promyelocytic Leukemia Pml/Rarî± Fusion Gene Using Graphene Modified Glassy Carbon Electrode, Zhi-Xian Lian, Guang-Xian Zhong, Kun Wang, Ai-Lin Liu, Xin-Hua Lin, Yuan-Zhong Chen

Journal of Electrochemistry

A graphene modified glassy carbon electrode (GCE) was prepared by electrochemical reduction of graphite oxide fixed on the surface of GCE. Then, the amino-group modified probe of acute promyelocytic leukemia (APL) PML/RARα fusion gene fragment was immobilized onto surface of the graphene modified GCE by coupling activating agent. With methylene blue (MB) as a novel electrochemical indicator, artificial APL PML/RARα fusion gene fragment was measured by differential pulse voltammetry (DPV). The result indicated graphene nanomaterial showed good sensitization on the signal of MB. The relationship between the reduction peak current of MB and the concentration of complementary strand was linear …

Study On Direct Electro-Oxidation Of Anisaldehyde, Lin-Lin Wu, Ying-Hong Zhu, Shan-Shan Li, Hong-Yan Zeng, Chun-An Ma

Journal of Electrochemistry

The oxidation of anisole on Pt electrode was investigated by cyclic voltammery and constant potential electrolysis. The influence of scan rates, substrate concentration, supporting electrolytes and solvent were considered . The results show that the electro-oxidation process of anisole was irreversible. In this research the sulfuric acid was the best supporting electrolytes and acetone was the best solvent, and the process was controlled by diffusion . The product of constant potential electrolysis was charactered by GC-MS .The results show that the main products was anisaldehyde, and the selectivity was up to 66.5% when using acetone as solvent.

Electric Vehicles And Power Batteries, Xin-Ping Ai, Han-Xi Yang

Journal of Electrochemistry

In retrospect of the historical development of Electric Vehicles (EV), the impact of battery technologies on the progress of EV was discussed. In consequence, it is concluded that the lack of advanced batteries was the main cause for the fluctuations of EV development and the sluggish commercialization of electric cars in the past century. After a brief introduction to the classification and the requirements of electric vehicles, the main issues of the batteries including safety, temperature range for operation and the cost as well as the effects of these factors on the applications of advanced batteries for electric vehicles were …

Anode Electrodeposition Of Ti/Mno2 Electrode And Electrocatalytic Oxidization Properties Of Phenol Degradation, Ye Chen, Wen-Li Zhao, Qing Wen

Journal of Electrochemistry

Ti-base manganese dioxide (Ti/MnO₂) electrode was prepared by anodically electrodeposition technology in this paper. The structure of the electrode, the microstructure of the electrode surface and the element composition of the electrode were analyzed by XRD, SEM and EDS. The preparation process parameters of the electrode were studied in detail with the help of the V~logi curve and phenol degradation curve. The Ti/MnO₂ electrode was anodically electrodeposited at current density 4mA•cm^-2, the Mn^{2 +} ions concentration 0.5mol•L^-1 and temperature70℃. The V~logi curve and phenol degradation curve were used to evaluate electrocatalytic oxidization properties …

Preparation And Performance Of Carbon-Coated Si/C Composites, Li-Li Du, Quan-Chao Zhuang, Tao Wei, Yong-Li Cui, Zhi Sun, Shi-Gang Sun

Journal of Electrochemistry

Si/C composite for lithium ion batteries was obtained by pyrolyzing and ball-milling. The microstructure and component of the composite was characterized by SEM and XRD, the electrochemical performance was investigated by electrochemical impedance spectroscopy (EIS), cyclic voltammetry (CV) and galvano static charge-discharge tests. The results illustrate that the particle of Si/C composite prepared by pyrolysis exhibits inerratic morphology, uniform carbon-coating layer, good electrical conductivity, low resistance. The first intercalated-lithium capacity of the composite material is 4495 mAh/g; the first coulomb efficiency is 65.3%. From the second week the coulomb efficiency maintains 97%, and the capacity at the 100th cycle can …

Influence Of Tert-Butylpyridine On The Band Energetics Of Nanostructured Tio2 Electrodes And The Photoelectrochemical Properties Of Dye-Seneitized Electrodes, Shu-Ming Yang, Ji-Chao Wang, Hui-Zhi Kou, Hong-Bin Xue, Hong-Jun Wang, Yu-Ling Guo

Journal of Electrochemistry

The flat band edges (Efb) of nanostructured TiO₂ electrodes in electrolyte solutions with tert-butylpyridine (TBP) of different concentrations have been determined with spectroelectrochemical technique. TBP played a role in band energetics of nanostructured TiO₂ electrodes. The Efb values of -2.25, -2.46 and -2.62 V were determined in three 0.2 mol•L^-1 tetrabutylammonium perchlorate (TBAP) acetonitrile electrolytes which contain 0, 0.2 and 0.4 mol•L^-1 TBP respectively. The addition of Li+ ions shifted Efb positively. The Efb values of -1.12, -1.22 and -1.30 V were determined in three 0.2 mol•L^-1 LiClO₄ acetonitrile electrolytes which contain 0, 0.2 …

Dft Study Of Co2 Reduction To Hydrocarbons On Cu Surfaces, Li-Hui Ou, Sheng-Li Chen

Journal of Electrochemistry

CO₂ reduction on Cu(111) single crystal surfaces was studied using DFT calculations on the reaction energies and the minimum energy paths. The results indicated that the possible reaction paths for CO₂ reduction on Cu(111) surface are CO₂(g) + H* → COOH* → (CO +OH)*, (CO + H)* → CHO*, CHO + H → CH₂O* → (CH_2⁺O)*, CH₂* + 2H* → CH₄ or 2CH₂* → C₂H₄. On Cu(111) surface, the reaction rate is controlled by steps of CH₂O* → (CH_{2 …}

Electrochemical Studies Of Zinc Injection Into The Structure Materials Of Nuclear Power Plants, Sheng-Han Zhang, Yu Tan, Ke-Xin Liang

Journal of Electrochemistry

The electrochemical and semiconductor characters of oxide films formed on 304L, 316L stainless steel and alloy 600 in high temperature water with zinc addition were studied. Stress corrosion cracking and occupational radiation can be retarded effectively by zinc injection to the primary circuit of pressurized water reactor (PWR). The semiconductor characters of the materials formed by zinc injection was analyzed by Mott-Schottky curves. The surface morphology and components of the corrosion oxide layer were examined and detected by scanning electron microscope (SEM) and X-ray photoelectron spectroscopy (XPS). The result reveals that the smaller crystals and the complex Zn-Cr-Ni-Fe oxide were …

Electrochemical Capacitive Performance Of Mesoporous Carbon Based Co-Ni Oxides, Zhen-Sheng Yang, Ling-Bin Kong, Li Deng, Yong-Chun Luo, Long Kang

Journal of Electrochemistry

By using defects on the surface of CMK-3 served as nucleation center, Co_0.25Ni_0.75 oxide/C composite was successfully prepared through a simple chemical co-precipitation method. Characterization was carried by using X-ray diffraction, BET and scanning electron microscopy. Results showed that a perfect mesoporous network of interconnected nanoflakes was obtained for Co_0.25Ni_0.75 oxide/C composite and, this material has a less crystallization, interconnected nanoflakes network structure and a narrow mesoporous distribution at about 3~4 nm. The highly dispersed and loosely packed Co_0.25Ni_0.75 oxide/C composite possessed good electrochemical accessibility and fast diffusion rate of OH …

Comparison Of Catalytic Performance On Different Materials Supported Pd Catalysts For Formic Acid Oxidation, Su-Dong Yang, Yan-Yu Liang, Zhu-Liang Wen, Qi-Jun Song, Xiao-Gang Zhang

Journal of Electrochemistry

Graphite oxide (GO) was prepared from by Hummers method. Then the graphene nanosheets supporting Pd catalysts were prepared by a single-step chemical reduction method. The electrocatalytic performance for formic acid oxidation of the prepared Pd/graphene composite was studied as an electrode material in comparison with the composite catalysts based on the other carbons (MWCNTs, SWCNTs, and Vulcan XC-72 carbon black). X-ray diffraction (XRD) and transmission electron microscopy (TEM) measurements indicated that the Pd nanoparticles were well dispersed on the surface of the graphene nanosheets with a small particle size. The electrocatalytic oxidation of formic acid was studied by electrochemically active …

Self-Assembling Organic Semiconductors With Tunable Electronic Properties Based On Novel Asymmetric Phenazine And Bisphenazine, Kyoungmi Jang

UNLV Theses, Dissertations, Professional Papers, and Capstones

Current demands in the area of organic semiconductors focus on both electronic and self-assembling properties. Particularly, one-dimensionally grown nanostructures of small organic semiconductors have drawn much attention for nanodevice fabrication. Self-assembly through various intermolecular interactions has been widely used to produce one-dimensionally grown nanostructures which can be induced by various methods such as rapid solution dispersion, a phase transfer method, vapor annealing, crystallization, and organogelation in conjunction with proper molecular design. Controlling the morphology of the nanostructures plays an important role in achieving desirable properties in optoelectronic device applications. While significant advancements have been made in developing molecular architectures for …

Preparation And Electrochemical Properties Of Sn Thin Film As Anode Materials For Lithium-Ion Batteries, Hong-Mei Bai, Zhan-Liang Tao, Fang-Yi Cheng, Jun Chen

Journal of Electrochemistry

Sn thin films as the anode materials of Li-ion batteries were prepared by vacuum-evaporation method on the copper foam substrate. The phase structure,surface morphology and electrochemical property of the as-prepared films were characterized by X-ray diffraction(XRD),scanning electron microscopy(SEM), and galvanostatic cycling. The results showed that three-dimensional structure of copper foam substrate enhanced the adhesion strength between the active material and the substrate, under the same substrate temperature, the particles became bigger with the increasing of evaporation time, while their electrochemical property decreased, under the same evaporation time, the particles didn′t changed obviously with the increasing of substrate temperature,while their cycle …

Synthesis Of Mesoporous Nickel Oxide For Supercapacitor Application, Xuan-Xuan Chen, Zhen-Zhen Zhao, Deng-Chao Wang, Zhong-Jie Huang, Wen-Bin Ni, Li Yu, Jian-Wei Zhao

Journal of Electrochemistry

Mesoporous nickel oxide has been synthesized by calcining metal-organic coordination precursor.Transmission electron microscopy and BET test showed that the prepared NiO had a regular morphology and displayed a narrow size distribution.Electrochemical tests revealed that such mesoporous NiO had a specific capacity of 72 F·g^-1 at the current of 2.0 A·g^-1.Futhermore,the material showed excellent cycle-life stability.There was no degradation of capacitance after 1000 cycles.