Chemistry Commons^™

An Enzymatic Ethanol/O2 Biofuel Cell Powered By Commercial Vodka Fuel, Yi-Ming Yan, Lan-Qun Mao

Journal of Electrochemistry

This study demonstrates the performance of a new type alcohol/O₂ biofuel cell assembled by using alcohol dehydrogenase (ADH) and bilirubin oxidase (BOD) as the biocatalysts of the bioanode and the biocathode for the bioelectrocatalytic oxidation of alcohol and reduction of oxygen, respectively. To construct the bioanode and the biocathode, single-walled carbon nanotubes (SWCNTs) were used. In the bioanode, SWCNTs were used as the supporting materials for both methylene green (MG) which was used as the electrocatalyst for the oxidation of NADH and ADH. The as-constructed MG/ADH/SWCNTs-based bioanode exhibits a good activity toward the bioelectrocatalytic oxidation of ethanol. In the …

Reconfigurable Solid-State Dye-Doped Polymer Ring Resonator Lasers, Hengky Chandrahalim, Xudong Fan

Faculty Publications

This paper presents wavelength configurable on-chip solid-state ring lasers fabricated by a single-mask standard lithography. The single- and coupled-ring resonator hosts were fabricated on a fused-silica wafer and filled with 3,3′-Diethyloxacarbocyanine iodide (CY3), Rhodamine 6G (R6G) and 3,3′-Diethylthiadicarbocyanine iodide (CY5)-doped polymer as the reconfigurable gain media. The recorded lasing threshold was ~220 nJ/mm² per pulse for the single-ring resonator laser with R6G, marking the lowest threshold shown by solid-state dye-doped polymer lasers fabricated with a standard lithography process on a chip. A single-mode lasing from a coupled-ring resonator system with the lasing threshold of ~360 nJ/mm² per pulse …

Platinum Hollow Nanospheres With Different Sizes: Controllable Synthesis And Electrocatalytic Oxidation Toward Methanol, Xuan Lin, Mei-Qin Cheng, Zhong-Jin Shang, Ting Xiong, Xian-Tu Zhang, Wei Tian, Jian-Yun Lin, Qi-Ling Zhong, Bin Ren

Journal of Electrochemistry

The selenium (Se) templates and hollow platinum (Pthollow) nanospheres with different sizes were controllably synthesized by adjusting the concentration of sodium dodecyl sulphonate (SDSN) (CSDSN, μmol·L-1) which was used as a surfactant. Accordingly, the Pthollow nanospheres modified glassy carbon (GC) electrode (Pthollow/GC) was prepared. The morphology and composition of Pthollow nanospheres were characterized by scanning electron microscopy (SEM), transmission electron microscope (TEM), energy dispersive X-ray spectroscopy (EDX), high resolution transmission electron microscopy (HRTEM), selected area electron diffraction (SAED) and X-ray diffraction (XRD) techniques. The electrocatalytic activities of Pthollow/GC and electrodeposited Pt nanoparticles modified glassy carbon electrode (Ptnano/GC) toward methanol oxidation …

Comparison In Factors Affecting Electrochemical Properties Of Thermal-Reduced Graphene Oxide For Supercapacitors, Peng Xiao, Da-Hui Wang, Jun-Wei Lang

Journal of Electrochemistry

In this paper, thermal-reduced graphene oxide (T-RGO) materials are synthesized by modified Hummer’s method, followed by thermal reduction under argon atmosphere at different temperatures. Electrochemical investigations show that, for T-RGO electrodes, good electrical conductivity is necessary and the surface functional groups play more significant role than the specific surface area in determining the electrochemical capacitance. The T-RGO obtained at 900 °C (T-RGO900) with a relatively high Brunauer-Emmett-Teller (BET) surface area (314 m²·g^-1) and a high electrical conductivity (2421 S·m^-1) shows a low specific capacitance of 56 F·g^-1. In comparison, the T-RGO obtained …

Synthesis Of Namnpo4 By Spraying Drying-High Temperature Sintering And Its Electrochemical Performance, Xiao-Chen Lin, Xiao-Biao Wu, Xu Hou, Yong Yang

Journal of Electrochemistry

As a cathode material for sodium ion batteries, NaMnPO₄/C nanocomposite is successfully synthesized by the combination of spraying drying and high temperature sintering methods. The crystal structure of the as-synthesized phosphate material is confirmed as the natrophilite NaMnPO₄, which possesses orthorhombic symmetry and Pmnb space group. It is shown that the precursors are hollow spherical particles and the obtained product consists of micro-scaled secondary particles, which are composed of NaMnPO₄ nanocrystallites (tens of nanometres) and amorphous carbon networks. The ionic and electronic conductivities of NaMnPO₄ are both effectively enhanced with the help of this …

One-Step Synthesis Of Pani/Nihcf Hybrid Film Using Unipolar Pulse Electrodeposition And Its Electrocatalytic Reduction Performance For H2O2 Detection, Sen-Liang Liao, Xiu-Min Li, Xiao-Gang Hao, Yan-Hong Wang, Chun-Feng Xue, Yong-Hong Wang

Journal of Electrochemistry

Organic–inorganic hybrid films composed of polyaniline/nickel hexacyanoferrate (PANI/NiHCF) were fabricated on platinum substrates using unipolar pulse one-step electrodeposition. The deposition mechanism of hybrid film was proposed: Due to high potential of unipolar pulse electrodeposition, which avoided the reduction of Fe(CN)₆^3-, the films with high electrocatalytic property and “insoluble” form of NiHCF were achieved. The morphology and composition of PANI/NiHCF hybrid film were characterized by scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), and Fourier transform infrared spectroscopy (FT-IR). The effect of pulse potential on the electrochemical performance of hybrid film was investigated in detail. Results showed that …

Electrochemical Applications Of Single-Walled Carbon Nanohorns, Su-Ping Li, Huai-Min Guan, Shu-Yun Zhu, Muhammad Rehan Hassan Shah Gilani, Saima Hanif, Guo-Bao Xu, Yue-Jin Tong

Journal of Electrochemistry

Single-wall carbon nanohorns (SWCNHs) have unique properties, such as a large specific surface area, good electrical conductivity and biocompatibility. It has been widely utilized in many fields. In the present review, the progress in electrochemistry study of SWCNHs has been summarized and the future research trends have been proposed.

Direct Electrochemistry And Glucose Biosensing Of Glucose Oxidase-Gold Nanoparticles Composite Synthesized By Enzyme Method, Fang He, Xiao-Li Qin, Ying-Chun Fu, Chao Chen, Qing-Ji Xie, Shou-Zhuo Yao

Journal of Electrochemistry

Glucose oxidase (GOx)-gold nanoparticles (AuNPs) composite was synthesized by the one-pot enzyme reaction in the mixture solution of NaAuCl₄, GOx and glucose, and a Nafion/GOx-AuNPs/glassy carbon electrode was fabricated by the cast-coating method to examine the direct electrochemistry of GOx and the biosensing performance on this electrode. Such a GOx-AuNPs composite showed good direct-electrochemistry activity and bioactivity of GOx, probably because the enzyme-mediated AuNPs are close to the redox active centers of GOx. This enzyme electrode exhibited a linear amperometric response to glucose concentration (0.54 mmol·L^-1) at -0.4 V (vs. SCE), and a detection limit of …

Density Functional Theory Study On The Structures Of Solvent-Ion In The Electrolyte Of Lithium Ion Battery, Li-Dan Xing, Ru Yang, Xian-Wen Tang, Wen-Na Huang, Qi-Feng Liu, Qi-Peng Yu, Wei-Shan Li

Journal of Electrochemistry

In this work, the possible structures of solvent-ion complex, resulting from the electrostatic interaction in the propylene carbonate (PC) base electrolyte of lithium ion battery, have been investigated using the density functional theory. The calculated results show that the structure of solvent-ion complex depends on the solvent number. In the PC base electrolyte, maximum number of PC solvents that coexist in the Li⁺-solvent sheath is four. Additionally, the salt anion exists in a complex with the positively charged alkyl group of PC rather than in a free state. The calculated results give a good explanation to the reported …

Boosting Electrocatalytic Activity Of Nitrogen-Doped Graphene/Carbon Nanotube Composite For Oxygen Reduction Reaction, Yu Zhang, Jin-Song Hu, Wen-Jie Jiang, Lin Guo, Zi-Dong Wei, Li-Jun Wan

Journal of Electrochemistry

Developing low-cost catalysts with high electrocatalytic activity for oxygen reduction reaction (ORR) has recently attracted much attention because the sluggish ORR currently limits the performance and commercialization of fuel cells and metal-air batteries as well. Nitrogen doped carbon materials have been considered as a promising candidate for the replacement of high-cost and scarce Pt-based catalysts although their electrocatalytic activity still needs to be much improved. In this work, an improved nitrogen-doped graphene/carbon nanotubes composite (N-rGO/CNT) was developed as an efficient ORR electrocatalyst. It was found that the ORR activity of N-rGO/CNT composite could be significantly enhanced by introducing iron in …

Influence Of Pt:Ru Ratio In Nanotubes Array Structures On The Electrocatalytic Activity Of Methanol Oxidation, Jin-Hua Yuan, Feng-Bin Wang, Xing-Hua Xia

Journal of Electrochemistry

Bimetallic PtRu nanotubes array electrodes (NTAEs) with varied Pt to Ru atomic ratios have been prepared by electrochemical codeposition in 3-aminopropyltri-methoxysilane modified porous anodic alumina (PAA) membranes. The structure and morphology of the catalysts were characterized using X-ray diffraction (XRD) and scanning electron microscopy (SEM), respectively. Electrochemical results showed that the NTAEs with varied atomic ratios could be achieved by controlling the precursor concentration for deposition. The prepared nanoarrays composed of Pt or PtRu alloy promoted the mass-normalized activity toward the sluggish electrooxidation reaction of methanol due to the increased catalytic activity and real surface area, as well as the …

Recent Progress In Heteroatoms Doped Carbon Materials As A Catalyst For Oxygen Reduction Reaction, Wei Ding, Xue Zhang, Li Li, Zi-Dong Wei

Journal of Electrochemistry

Developing catalytic materials for oxygen reduction reactions (ORR) with high performance and low cost has been one of the major challenges for large-scale applications of fuel cells. In this review, we summarize the recent progress in the heteroatoms doped carbon materials as a catalyst for the catalysis of ORR, with an emphasis on the universal origin of their catalytic mechanisms. The future prospects of the metal-free catalyst were to find precisely controlled doping methods, to explore the role of heteroatoms in the catalysis, and to generate more active catalysts with suitable nanostructure.

Electrochemistry Of Glucose Oxidase Modified On Porin-Phospholipid Biomimic Membrane, Kun-Qi Wang, Zuo-Ming Zhang, Wei Xing, Chang-Peng Liu, Xing Zhou

Journal of Electrochemistry

Biomimic membrane with nano-channels, which is made up of porin MspA and 1,2-Dimyristoyl-sn-glycero-3-phosphocholine (DMPC) is constructed on glassy carbon substrate, and glucose oxidase (GOD) is modified on it. The direct electrochemical reaction and electrocatalytic behavior to oxygen and glucose of GOD on the GOD/MspA-DMPC/GC electreode are expounded by the cyclic voltammetric method. The study shows that GOD immobilized on porin MspA and DMPC biomimic membrane displays direct and surface-controlled electrochemical reaction nearby formal potential (E0′) of the flavoprotein active centre (FAD/FADH), and the electrochemical reaction contains two electrons and two protons exchange in 0.1 mmol·L^-1 phosphate buffer solution (PBS) …

Fabrication Of Pattern Of Graphene Oxide And Au Nanoparticles By Microcontanct Printing Technique, Wen-Hui Pang, Xiao-Jian Xiao, Meng-Wei Ye, Kai-Chao Deng, Jing Tang

Journal of Electrochemistry

Graphene oxide (GO) was prepared by modified Hummers method. Using the GO solution as "ink", Au nanoparticles (AuNPs) and GO were transferred to the surface of ITO substrate modified with (3-aminopropyl) triethoxysilane (APTES/ITO) in a sequence. The transferred AuNPs and GO could form a uniform and dense composite pattern which was characterized by FE-SEM and AFM. Moreover, using the APTES/ITO substrate surface potential as zero, the sequences of the surface potential were APTES>GO>Au.

Effect Of Imidazole Ionic Liquids On The Electro-Oxidation Of P-Methoxy Toluene, Qiong Chen, Ying-Hong Zhu, Ying Zhu, Yan-Fang Li, Chun-An Ma

Journal of Electrochemistry

The interactions between four Imidazole ionic liquids (EMIMBF₄, BMIMBF₄, BMIMHSO₄, BMIMAc) and p-methoxy toluene were investigated by ultraviolet spectroscopy. The red shifts of absorption peak were obviously observed, and the fine structures of the spectroscopy were disappeared on the long wave district. p-MT producing stable excited state was benefit from the interaction with solvent molecules. The electro-oxidation behavious of p-MT were studied in the four ILs on platinum electrode by cyclic voltammetry (CV) and chronoamperometry (CP), and the diffusion coefficients (D) and activation energies (ED) were calculated. The results indicated that the electro-oxidation process …

Fabrication And Characterization Of The Ni-Scsz Composite Anodes With A Cu-Lscm-Ceo2 Catalyst Layer In The Thin Film Sofc, Yao Lv, Bo Huang, Xi-Zhi Gu, Chun-Yi Hou, Yi-Xing Hu, Xiao-Yin Wang, Xin-Jian Zhu

Journal of Electrochemistry

Solid oxide fuel cell (SOFC) directly operating on hydrocarbon without external reforming has the potential of greatly speeding up the application of SOFCs for transportation. In this paper, a three-layer structure anode was fabricated by tape casting and screen printing method. The addition of Cu-LSCM-CeO₂ to the supported anode surface presented better performance running on H₂ and ethanol. The maximum power densities were 511 and 390 mW?cm^-2, respectively, running on H₂ and ethanol at 750 °C. No significant degradation was observed on the anode. Consequently, the Cu-LSCM-CeO₂ catalyst layer on the surface of the …

Review Of Carbon Materials Energy Storage Mechanism In Lead-Carbon Battery, Le-Ying Wang, Hao Zhang, Chen Hu, Shu-Kai Zhang, Hai-Lei Zhao, Gao-Ping Cao, Wen-Feng Zhang, Yu-Sheng Yang, Xiao-Kang Lai

Journal of Electrochemistry

The traditional lead-acid batteries are mainly used for automobile and various internal combustion engine starting, wireless communication base stations and renewable energy storage; however, their negative plates are easily sulfated under partial-state-of-charge duty, then their charging capacity and cycle life are greatly reduced. Lead-carbon battery is a new type of lead-acid battery, in which a carbon material with high specific surface area and conductivity is added into a negative plate, and has excellent rate discharge performance and higher PSoC cycle life. Lead-carbon battery has a good application prospect in energy storage and hybrid electric vehicle, so these years the study …

Determination Of Folic Acid By Composite Film Electrode Modified With Poly-Alizarin Red And Multi-Walled Carbon Nanotubes, Xue-Ping Du, Tong-Fang Lou, Ying Dong, Jian-Ying Qu

Journal of Electrochemistry

The novel modified electrode was fabricated by electropolymerizing alizarin red onto the surface of multi-walled carbon nanotubes on glassy carbon electrode surface, which exhibited good electrocatalytic activity for folic acid. The experimental results showed that the reduction peak current of folic acid at -0.63 V was linear to its concentration over the range of 1.25×10^-6 ~ 4.00×10^-5 mol·L^-1 in the optimized experimental conditions (R = 0.9985). Test for recovery was carried out by standard addition method, and the recovery ratios were in the range of 92.0% ~ 102.0%. The modified electrode was prepared simply with excellent stability, …

Electro-Catalytic Properties Of Β-Pbo2/Sb-Sno2/Ti Electrode On Phenol Oxidation, Peng Li, Yue-Min Zhao, Li-Zhang Wang, Yan-Le Zhang, Zhao-Qing Lu

Journal of Electrochemistry

The combination technology of brush pyrolysis and electroplating was employed in the preparation of β-PbO₂/Sb-SnO₂/Ti electrode. X-ray Diffraction (XRD) and Scanning Electron Microscope (SEM) results showed that the Sb-SnO₂ as an interlayer would restrain the formation of lead fluoride and the crystallization degree on the electrode surface could be as high as 100%. The grain size was calculated by Scherrer formula to be 25.2 nm and the agglomeration of lead dioxide was effectively eliminated. The potential span of diffusion control phase, oxygen evolution potential, Tafel slope for the β-PbO₂/Sb-SnO₂/Ti electrode during …

Electrochemical And Spectroscopic Studies Of Ethanol Oxidation On Nano-Cubic Pt Modified By Tin Adatoms, Lu Rao, Bin-Wei Zhang, Yan-Yan Li, Yan-Xia Jiang, Shi-Gang Sun

Journal of Electrochemistry

The nano-cubic Pt modified by tin (Sn) was synthesized and used to investigate the role of this adatom played in the ethanol oxidation. The onset potential of ethanol oxidation was significantly shifted negatively which can be forward about 300 mV when the coverage of Sn (θSn)was 0.9. The electrtochemical in situ FTIR result demonstrated that the amount of CO₂ increased first, and then decreased with θSn increased, and reached the maximun when θSn was 0.38. Furthermore, the formation of acetic acid could be observed at very low potential (-0.05 V) after modifying Sn adatom, and the amount of acetic …

Preparation Of Pt/Dna-Mwcnts/Gc Electrode And Its Electrocatalytic Activity Toward H2O2 Reduction, Li-Li Fan, Li-Na Wu, Zhi-Yu Qu, Dan-Feng Liu, Jun-Ming Zhang, Si-Ming Fan, You-Jun Fan

Journal of Electrochemistry

The DNA-multi-walled carbon nanotubes (MWCNTs)/glassy carbon (GC) electrode was prepared by modifying the DNA functionalized MWCNTs composite on a GC electrode. A novel non-enzymatic H₂O₂ sensing electrode was fabricated by electrodepositing Pt nanoparticles on the DNA-MWCNTs/GC electrode. The modified electrodes were characterized by scanning electron microscope (SEM). The response properties of the sensing electrode to H₂O₂ were investigated by cyclic voltammetry and chronoamperometry. The results indicated that the sensing electrode exhibited a good linear relationship between response current and H₂O₂ concentration in the range of 0.04 ~ 18.07 mmol·L^-1 with …

Synthesis, Fabrication And Characterization Of Magnetic And Dielectric Nanoparticles And Nanocomposite Films, Xiaohua Liu

Dissertations, Theses, and Capstone Projects

Materials science is an interdisciplinary field investigating the structure-property relationship in solid-state materials scientifically and technologically. Nanoscience is concerned with the distinctive properties that matter exhibits when confined to physical dimensions on the order of 10^-9 meters. At these length scales, behaviors of particles or elaborate structures are often governed by the rules of quantum mechanics in addition to the physical properties associated with the bulk material.

The work reported here seeks to employ nanocystals, binary nanocomposites and thin films of materials, to build versatile, functional systems and devices. With a focus on dielectric, ferroelectric, and magnetoelectric performance, a …

Epoxy Catalyzed Sol-Gel Method For Pinhole-Free Pyrite Fes2 Thin Films, S. Kment, H. Kmentova, A. Sarkar, R. J. Soukup, N. J. Ianno, D. Sekora, J. Olejnicek, P. Ksirova, J. Krysa, Z. Remes, Z. Hubicka

Department of Electrical and Computer Engineering: Faculty Publications

The uniform pinhole-free iron disulfide (FeS₂) pyrite thin films were fabricated. In the first step the FeO(OH)_x xerogel solution was synthetized by means of a novel epoxy catalyzed sol-gel method and next spin-coated onto various substrates to form the thin films. In the second step the xerogel coatings were annealed to yield hematite (α-Fe₂O₃) films, which were transformed into pyrite by chemical sulfurization. Among the main deposition parameters studied were the temperature of xerogel-hematite transformation and the optimal sulfurization temperature and duration. It has been observed that 15 min sulfurization at the temperature …

Electrochemical Catalysis: A Dft Study, Li Li, Zi-Dong Wei

Journal of Electrochemistry

In this review, we focus on achievements in electro-catalysis based on the density function theory study. The relationships among the electrode potential, electronic structure of catalysts and electro-catalytic activity are summarized in three parts: the adsorption and desorption of species, electron transfer, and stability of catalysts. The electrode potential and the electronic structure (d-band center or Fermi (HOMO) energy) of catalysts significantly influence the formation, adsorption and desorption of surface species on electrode. The electro-catalytic activity can be improved by modulating the electrode potential and electronic structure of catalysts.

Electrocatalytic Oxidation Of Formate On Pd-Cu/C - Effect Of Dealloying Pretreatment, Kun Jiang, Ye Wang, Tao Lin, Wen-Bin Cai

Journal of Electrochemistry

Carbon supported highly dispersed Pd-Cu nanoalloy catalyst toward formate electrooxidation is prepared via one-pot synthesis by using ethylene glycol as the reducing agent and sodium citrate as the stabilizer. The as-prepared catalyst is structurally characterized by TEM and XRD. The Cu dealloyment is carried out through repetitive potential cycling of the Pd-Cu/C catalyst in an acidic solution. The dealloying effect on the performance of the Pd-Cu/C is investigated by using cyclic voltammetry and chronoamperometry, and the surface structural change of Pd-Cu/C is probed by in situ ATR-IR measurement. The results show that the as-prepared Pd-Cu/C processes a better long-term stability …

Synthesis Of Silver Nanoparticles Supported On Graphene Quantum Dots For Oxygen Reduction Reaction, Jian Ju, Wei Chen

Journal of Electrochemistry

Silver-based catalysts have been extensively investigated as the platinum substituted catalysts due to their high catalytic efficiency, low cost and long-term durability. In this study, the surfactant-free silver nanoparticles supported on graphene quantum dots were synthesized through a facile approach without addition of any other protecting ligands and reducing agents. The “surface-clean” silver nanoparticles had remarkable electrocatalytic performance towards oxygen reduction reaction (ORR) with the most efficient four-electron transfer process. Compared with commercial Pt/C catalyst, the hybrid nanoparticles showed comparable catalytic performance for ORR but much higher tolerance to methanol. Such silver nanoparticles supported on graphene quantum dots may have …

Preparation And Lithium Storage Performance Of Sn-Snsb Nanoparticles, Yao Xiao, Jiao-Hong Wu, Qi Wang, Ling Huang, Jun-Tao Li, Shi-Gang Sun

Journal of Electrochemistry

Tin was widely studied as alternative anode material to carbon for lithium-ion batteries thanks to its much higher theoretical capacity. However, a pure tin electrode suffers severely from its poor cycleability due to mechanical fatigue caused by volume change during lithium insertion and extraction processes. Tin-based alloy may improve the cycleability property of tin electrode. In this article, we report facile synthesis of spherical Sn-SnSb nanopartciles using a simple solvent-thermal approach. It is amazing to find that the spherical Sn-SnSb nanoparticles can circumvent volume changes effectively during charge-discharge process. Electrochemical discharge/charge results show that the spherical Sn-SnSb nanoparticles electrode exhibits …

Electrochemical Fabrication Of Two-Dimensional Flower-Like Pt Nanostructures For Methanol Electrocatalytic Oxidation, Xia Wang, Jun Hu, Yong-Jun Li

Journal of Electrochemistry

Two-dimensional flower-like Pt nanostructures (2D FPNs) were fabricated on glassy carbon substrates by galvanostatical electrochemical technique. The electrolyte was the HAuCl₄ + HClO₄ aqueous solution without addition of any structure-directing organic reagent, which made as-prepared Pt nanostructures cleaner, exhibiting much higher reactivity. Scanning electron microscopic images revealed that 2D FPNs were spherical Pt nano-flowers constructed by the smallest building blocks, nano-leaves. The number density of spherical Pt nano-flowers can be tuned by controlling the electrodeposition time. High resolution transmission electron microscopic images indicated that each nano-leaf was formed by growing along Pt(111) direction. Electrocatalytic activities of as-prepared 2D …

A Sensitive And Label-Free Electrochemical Aptasensor Based On Signal Amplification Of Carbon Nanotubes, Chun-Yan Deng, Hui-Min Fan, Juan Xiang, Yuan-Jian Li

Journal of Electrochemistry

A label-free electrochemical sensing electrode for highly sensitive detection of adenosine was constructed based on the signal amplification of carbon nanotubes (CNTs). The change in the interfacial feature of the modified electrode was characterized by electrochemical impedance spectroscopy. Using [Ru(NH₃)₆]³⁺ as the signaling moiety, adenosine with concentrations as low as 0.027 nmol·L^-1 can be selectively detected. Additionally, the fabrication of this present aptasensor was simple, time-saving and cost-effective. Compared with other reported aptasensors, the proposed aptasensor had advantages of excellent sensitivity, selectivity and simplicity, which plays a potential role in development of aptasensor.

Investigation Of The Dynamics Of Photocarriers During Photoelectrochemical Water Splitting By Combination Of Photoelectrochemistry And Transient Absorption Spectroscopy, Wen-Hua Leng

Journal of Electrochemistry

Semiconductor photoelectrochemical hydrogen production is an important and promising technology for utilizing solar energy. The efficiency of hydrogen production depends on the efficiencies of separation and transport of photo-generated carriers. A deep understanding of the behavior of these processes has guiding significance for designing efficient solar hydrogen device. photoelectrochemical and transient absorption spectroscopy methods are powerful tool for studying the microscopic dynamics and mechanism of photocatalytic reaction. This review describes the part of the latest results of the author regarding the semiconductor photoelectrochemical hydrogen production obtained by these methods,and the problems and future research priorities in this field are proposed.