Chemistry Commons^™

Boron-Doped Homoepitaxial Diamond (100) Film Investigated By Scanning Tunneling Microscopy, Bing Xiao, Weihai Fu, Sacharia Albin, Jason Moulton, John Cooper

Electrical & Computer Engineering Faculty Publications

Conducting epitaxial diamond films of high quality are essential for many diamond studies and diamond electronic device fabrication. We have grown boron-doped epitaxial diamond films on type Ila natural diamond (100) substrates by microwave plasma chemical vapor deposition. A gas mixture of H₂/CH₄ was used. Boron doping was done by placing solid sources of pure boron in the microwave plasma. Homoepitaxial films with atomic smoothness were achieved under the following growth conditions: substrate temperature 900 °C, gas pressure 40 Torr, and gas flow rates of H₂/CH₄ = 900/7.2 seem. The growth rate was 0.87 …

Electrochemical Hydrogen Storage Properties Of Carbon Nanotubes, Xue Qin, Xue-Ping Gao, Feng Wu, Hong Liu, Ying Lan, Hua-Tang Yuan, De-Ying Song, Pan-Wen Shen

Journal of Electrochemistry

The electrochemical properties of carbon nanotubes (CNTs) electrode have been investigated in this paper. The high discharge capacity of 200 mAh·g^-1 was measured for the CNTs Ni electrode at a discharge density of 200 mAh·g^-1 . CNTs-Ni electrode, the high electrochemical activity and the long cycle life were observed. The electrochemical mechanism of hydrogen adsorption and oxidation at the CNTs Ni electrode was studied by cyclic voltammertry method.

Template Synthesis Of Nano-Structured Electrode Materials And Its Electrochemical Performance, Jian Zhao, Quan-Yong Gao, Yong Yang, Zu-Geng Lin

Journal of Electrochemistry

In this letter, various nano structured materials such as spinel LiMn₂O₄ nanotubes/nanowires and carbon nanotubes have been prepared by using porous alumina template. The prepared template and materials have been characterized by AFM and TEM techniques. It is shown that size of the nanotubes can be conveniently controlled by using template method. Some preliminary results of cyclic voltammetry about nano structured LiMn₂O₄ are also reported.

The Electrochemical Performance Of The Spinel Limn2O4, Shi-Gang Lu, Yu-Cheng Sun, Ren-Min Liu, Wei-Hua Jin, Wen-Zhong Li, Cang Han

Journal of Electrochemistry

The cathode material spinel LiMn₂O₄ of lithium ion battery was synthesized by making use of solid state reaction at 750～850 ℃. The discharge capacity was 115～125 mAh·g^-1 . It was observed that the capacity loss increase at the elvated 55 ℃ temperature. A little excess Li content and the Co doped spined could improved the cycle capability of the cathode material. The dissolution of the spined in the electrolyte was measured. The treatment method was used to stabilize the LiMn₂O₄ structure. It was found that the spinel LiMn₂O₄, treated …

The Memory Effect Of Mh-Ni Battery, De-Ming Xie, Jian-Ming Wang, Jian-Qing Zhang, Chu-Nan Cao

Journal of Electrochemistry

The memory effect of MH-Ni battery was investigated. The depth of discharge, discharge rate and cycle number influence the memory effect greatly. A few completely full charge/discharge cycles could eliminate it. The existence of the memory effect had nothing to do with zinc element. During the course of life cycling at low DOD (degree of discharge), the smaller the discharge current was, the lower was the maximum charge voltage. In addition, discharge voltage and discharge capacity drop fast at the beginning, gradually leveled off at about a value. If the discharge current was increased, the discharge capacity was obviously less …

The Development Of Carbon Monoxide Tolerant Catalysts For Proton-Exchange Membrane Fuel Cell, Zhong-Jun Hou, Hong-Mei Yu, Bao-Lian Yi, Ming Han

Journal of Electrochemistry

High over-potential of proton exchange membrane fuel cell (PEMFC) anode caused by carbon monnoxide poisoning when reformate or methanol is used as fuel is main obstacle to the high performance of PEMFCs. Using carbon monoxide tolerant catalysts is the most hopeful way to solve the CO problem. The CO poisoning problem is reviewed briefly in this paper, and the development of CO tolerant catalysts is introduced in details, including electrocatalysts activity, preparation method and mechanism of tolerance to CO.Mo and W can improve catalysts' CO tolerance. Multi-component catalysts are expected to be more tolerant to CO.

Investigation Of A Complex Lithium Cobalt Nickel Oxide As Lithium Ion Battery Cathode Materials Prepared By A New Citrate Sol-Gel Method, Jing-Li Han, Qing-Guo Liu

Journal of Electrochemistry

The synthesis and electrochemical characteristics of lithium cobalt nickel oxide as cathode materials for rechargeable lithium batteries were investigated. It was clarified from these investigations that lithium cobalt nickel oxide has been produced from basic cobalt carbonate,basic nickel carbonate, lithium carbonate, and citrate. LiNi_0.8Co _0.2O₂ prepared under the stream of oxygen gas showed a higher cycling capacity of (～190 mAh·g^-1).

Effect Of High Concentration Lithium Bromide Solution On Electrochemical Behavior Of Low Alloy Steel At High Temperature, Jian-Wei Guo, Cheng-Hao Liang

Journal of Electrochemistry

By electrochemical measurements and weight loss experiments, the effect of MoO₄^2- on low alloy steel's electrochemical behaviors was investigated at high temperature in 55%LiBr+0.07 mol/L LiOH solution. The results showed that MoO₄^2-, as an anodic inhibitor, formed passive film rapidly and impeded both anodic and cathodic procedures. Moreover, Na₂MoO₄ prevented corrosion effectively in 55%LiBr+0.07 mol/L LiOH solution when its concentration is more than 200 mg/L. The pitting potential increased accompanying to the arising of Na₂MoO₄ concentration. Some elements of alloy strengthened resistance to corrosion, shch as chromium and nickel, …

Studies Of Adsorption And Oxidation Of Ethanol On Nm-Pt/Gc Electrode——I. Cyclic Voltammograms And In-Situ Ftir Spectroscopy In Alkaline Media, Guo-Lian Chen, Shi-Gang Sun, Sheng-Pei Chen, Zhi-You Zhou

Journal of Electrochemistry

The electro-oxidation of ethanol on nm-Pt/GC electrode in alkaline solutions containing 0.02 mol·L^-1 NaOH+0.1 mol·L^-1 CH₃CH₂OH was investigated by using cyclic voltammetry and in-situ FTIR spectroscopy. The experimental results demonstrated that the main product of ethanol oxidation is CH₃COO^-, only very small amount of CH ³CHO has been determined simultaneously. In contrast with the dual path reaction mechanism for the oxidation of ethanol in acid media, the oxidation of ethanol in alkaline media didn't pass through the dissociative adsorption, and no adsorbed species could be determined even using a …

Detection Of Solid Pigment In Dermatoscopy Images Using Texture Analysis, Murali Anantha, William V. Stoecker, Randy Hays Moss

Chemistry Faculty Research & Creative Works

Background/aims: Epiluminescence microscopy (ELM), also known as dermoscopy or dermatoscopy, is a non-invasive, in vivo technique, that permits visualization of features of pigmented melanocytic neoplasms that are not discernable by examination with the naked eye. ELM offers a completely new range of visual features. One such feature is the solid pigment, also called the blotchy pigment or dark structureless area. Our goal was to automatically detect this feature and determine whether its presence is useful in distinguishing benign from malignant pigmented lesions.

Methods: Here, a texture-based algorithm is developed for the detection of solid pigment. The factors d and a …

The Effect Of Cerium On The Anodic Behavior Of Pb-Ca-Sn Alloy In Sulfuric Acid Solution, Hou-Tian Liu, Jiong Yang, Hai-He Liang, Ji-Hua Zhuang, Wei-Fang Zhou

Journal of Electrochemistry

The cyclic voltammograms for Pb - 0.5 at% Ca - 1.5 at% Sn and Pb - 0.5 at% Ca - 1.5 at% Sn containing a certain amount of cerium in 4.5 mol·dm^-3 H₂SO₄ at 20℃ were measured between 0.6 V and 1.4 V(vs. Hg/Hg₂SO₄). The growth rate of the anodic Pb(Ⅱ) films formed on the mentioned alloy electrodes at 0.9 V in the same sulfuric acid medium was investigated using the Linear Sweep Voltammetry. The variation with electrode potential of the real part of the impedence (Z’) for the anodic Pb(Ⅱ) films …

Cathodic Indirect Oxidation Of Organic Compounds(Ⅱ)——Cathodic Indirect Epoxidation Of Olefine, Xue-Ying Zhang, Bao-Qiu Cui, Deng-Ping Gu, Wei Li

Journal of Electrochemistry

We described a novel cathodic indirect epoxidation system in which O₂ was first cathodically reduced to H₂O₂. Then VO(acac)₂ was oxidized by H₂O₂ homogeneously to VO(acac)₂OOH which was used to epoxidize some olefine such as maleic, fumaric and crotonic acids. Many affecting factors on the current efficiency were optimized. The research will contribute to the developments of organic electrosynthesis.

The Electro-Catalytic Oxidation Of Hcooh On Electrodeposited Pd Electrode, Quan Zhou, Cun-Zhong Zhang, Xiao-Lin Lu, Zhong-Da Wu

Journal of Electrochemistry

The coherent electroplates were prepared by electro depositing Pd on supporting materials glassy carbon. The surface morphology of the electrodes was examined by SEM. The electro oxidation of HCOOH in HClO₄ solution was investigated by using cyclic voltammetry. The results show that the deposited conditions in the preparation of electrodes by electro depositing Pd affect the electrodes electro catalytic activity to the oxidation of HCOOH. The platinized Pd electrode on GC substrates using large current density is of higher catalytic activity to the oxidation of HCOOH than Pd electrode. The electro catalytic activity of PdO formed on the Pd …

The Study On Lithiated Titanium Composite Oxides As Negative Electrode For Lithium-Ion Battery, Xiao-Yan Yang, Shou-Nan Hua, Shu-Yong Zhang

Journal of Electrochemistry

Lithiated titanium composite oxides Li₄Ti₅O₁₂ were prepared from Li₂CO₃ and TiO₂. The XRD results of this composite oxides indicated that the compound had a spinel structure. The electrochemical behavior of lithiated titanium composite oxides was examined. The results showed that this material had an excellent cyclic capability and reversibility for lithium insertion, and had high specific capacity: the initial discharge capacity was 300 mAh·g^-1 , and the reversible capacity was 100 mAh·g^-1 . The discharge plateau (about 1.5 V) and the charge plateau (about 1.6 V) were very …

Studies Of The LialYNi1-YO2 As Cathode Materials For Rechargeable Lithium Ion Batteries, Xiao-Gan Li, Wei-Hua Qiu, Chuan-Gang Lin, Qing-Guo Liu

Journal of Electrochemistry

In this paper, we have synthesized series of single-phase LiAl_yNi_1-yO₂ (differentive in value-y) by solid reaction. Through examining their electrothemical properties, found that, under a proper sintering condition, Li_xAl_0.25Ni_0.75O₂ solution for cathode materials of rechargeable lithium ion batteries showed more pleasing properties in overcharge-resist and cycling life (vs LiNiO₂). When x>1, the capacity can be kept 125mAh/g after 30 cycles under higher charged/discharged voltages ranging from 3.0 V to 4.8 V, whereas that of pure LiNiO₂ has only 61 nAh/g after 25 cycles. The …

A Study On Stochastic Resonance For The Process Of Active-Passive Transition Of Iron In Sulfuric Acid, Hong-Bo Ding, Bao-Yun Xia, Chun-Sheng Yin, Zhong-Xiao Pan, Renato Seeber

Journal of Electrochemistry

The bistable characteristics of the process of active passive transition of iron in sulfuric acid was described and the stochastic resonance phenomenon in the process was simulated.

A Study On The Cylindrical Zinc-Air Battery, Sheng-Sian Li, Gui-Mao Zhou, Xin-Ping Ai, Han-Xi Yang

Journal of Electrochemistry

The zinc air battery has advantages of high specific energies and low cost, therefore attracts much interests. However, its application is limited only in prismatic and button type.This paper reported a novel design of cylindrical zinc air batteries and the performances of the batteries tested at various conditions. The results showed that when discharged at the current of 40 mA at 20 °C, the capacity of AA size and AAA size batteries reached 4000mAh and 1400mAh respectively, corresponding to the energy densities 280 Wh/kg and 200 Wh/kg. The effects of the discharge current, temperature and humidity on the performances of …

Synthesis Of Li1+XMn2O4 Cathode Material For Lithium-Ion Batteries With Solution Method, Pei-Song Liu, Sing-Quarn Liu, Qing Li, Zhao-Yong Chen, Bai-Lan Zhang, Zuo-Long Yu

Journal of Electrochemistry

The cathode materials Li_1+xMn₂O₄ were prepared with citric acid complexing and solution impregnating methods. Structure characterization and specific surface area test were performed by means of XRD, BET methods, the influences of calcination temperature, Li/Mn molar ratio and raw materials on the structure and electrochemical capacity of samples have beem examined. The results showed that the Li/Mn molar ratio and calcimation temperature were the key factors affecting the electrochemical capacity of cathode materias. The optimum conditions for synthesis of  Li_1+xMn₂O₄ cathode material were 0≤x≤0.05 and calcined at 750°C. The initial …

The Effect Of Anode Thickness In Sofcs With Anode Supported Ysz Film, Yi-Huang Zhang, Yi Jiang, Zi-Gui Lu, Yong-Lai Dong, Jing-Wang Yan

Journal of Electrochemistry

Solid oxide fuel cells with supported yttria stabilized zirconia electrolyte films on anode substrates of various thickness have been fabricated. The electrochemical performances of the SOFCs have been examined. The results showed that the cell performance was limited by the anodic overpotential, which is caused mainly by a concentration polarization when the anode substrate is thick. The anodic overpotential was reduced obviously as the thickness of anode substrate was decreased. As a result, the performance of the SOFC cell was improved. With a 0.5 mm anode substrate, a SOFC cell produced a power density about 0.19 W/cm² at 800 …

A New Method For The Preparation Of The Electrodes With Very Low Platinum Loading Used In Proton Exchange Membrane Fuel Cell, Zhi-Gang Shao, Bao-Lian Yi, Ming Han, Ya-Guang Qiao, Hao Liu, Jing-Rong Yu

Journal of Electrochemistry

Research and development on low platinum loading electrode is very important in reducing the cost of proton exchange membrane fuel cell(PEMFC) stack. This paper has put forward a new method to prepare the electrode of PEMFC. The pore forming substances were used in this methd. The low platinum loading electrodes (0.02 mg_Pt⋅cm^-2) have already been prepared with the method. Compared with the traditional method, the new method is simple, cheep, and easy to scale up. The superior composition of the electrodes is catalyst: pore forming substance: Nafion= 3:3:1. The performance of a single cell using this …

Study On Carbon From Pyrolyzing Phenol-Formaldehyde Resin For The Negative Electrode Of Li-Ion Secondary Battery, Zhi-Yuan Tang, Xin-Guo Zhuang, Yu-Mei Zhai, Jian-Gang Li, Jian-Jun Xue, Chun-Yan Liu

Journal of Electrochemistry

Li-ion secondary batteries negative electrodes were prepared by low temperature (<1 000 ℃) pyrolysis of commercial phenol-formaldhyde resin. A thermogravimetric analysis (TGA) and an X-ray diffraction (XRD) studies were peoformed for the pyrolytic carbonaceous materials. The results indicated that these samples are amorphous polyacenic structure materials. With increasing pyrolytic temperature, these materials become structurally order, and the first charge-discharge special capacities reduce. The specific capacities base on pyrolytic temperature, involving lithium storage nanometer cavities.

Technical Investigaton Of Thin-Film Plasticizing Lithium Ion Battery, Xin-Ping Ai, Xin-Lin Hong, Quan-Feng Dong, Sheng-Xian Li, Han-Xi Yang

Journal of Electrochemistry

A number of polymer materials as candidates of host matrix of plastic polymer electrolyte were examined and techniques for preparation of thin-film electrolyte were reported. The results showed that the polymer electrolyte prepared with P(VDF-HFP) copolymer as host matrix and DBP as plasticizer exhibit the satisfactory mechanical strength and ionic conductivity. In comprison with liquid electrolyte systems, thin-film lithium ion battery has almost similar charge-discharge capacity and cycleability. The manufacture methods and the technical factors in making plasticizing lithium ion battery were also described in details.

Study On The Effect Of Sodium Ion On Cycle Performance Of Lithium/Improved Graphite Lithium Ion Cell, Wen-Huang Huang, Yu-Shun Yan, Chun-Rong Wan, Chang-Yin Jiang

Journal of Electrochemistry

The different concentration of Na⁺ was introduced into the non-aqueous eletrolyte system EC/DEC/LiClO 4 with 4A molecular sieve and lithiated 4A molecular sieve, by which the trace amount of water was removed. The concentrations of Na⁺ and Li⁺ were determined by atomic adsorption spectrometry. The cycle performance of lithium/improved graphite cells was then examined by charging and discharging under the constant electric current. The results demonstrated that the cycle performance of the cells was destroyed by the high concentration of Na⁺ under the small electric current. With the increase of electric current the cell became less …

Powder Microelectrode Modified With Nafion-Os(Bpy)3Â 2+ And Pvp Composite And Its Catalysis For No2- Reduction, Pei-Fang Liu, Jia-Wei Yan

Journal of Electrochemistry

The modified powder microelectrode was prepared by etching a Pt (0.1 mm diameter) disk microelectrode and filling in thus formed cavity with Nation-Os(bpy)₃²⁺/PVP composite modified carbon powder. The composite modified powder microelectrode showed cyclic voltammetric behaviors changing with the mole ratio (denoted X) of SO₃^- to Os(bpy)₃²⁺ in Nafion. When X=3, a single pair of current peaks appeared near 0.6V (vs. SCE) due to Os(bpy)₃^2+/3+ redox couple. In contrast, for X=20, a pair of additional current peaks occurred near 0.4V. Both X=3 and X=20 modified powder microelectrodes strongly catalyzed the first …

Effects Of Temperature On The Proton Diffusion Of Doped Ni(Oh)2, Jian-Hua Liu, Jing-Wu Yang, Zhi-Yuan Tang

Journal of Electrochemistry

The Chronoamperometry of powder spherical Ni(OH)₂ microelectrode was used to study the proton diffusion coefficients of Ni(OH)₂. The proton diffusion coeefficients and the apparent diffusion active energy in anode and cathode processes at different temperature were obtained. Compared with pure Ni(OH)₂, the apparent diffusion active energy (E_a) of Ni(OH)₂ doped with Co and Co + Zn was decreased and the diffusion constant (D_o) was increased in the anode and the cathode processes, respectively, the effect of Co was greater. In contrast, for Ni(OH)₂ doped with Zn, its E_{a …}

Template Synthesis And Uv-Vis Absorption Spectra Of The Nanowire Arrays Of Cadmium Chalcogenides, Shi-Min Xu, Kuan-Hong Xue, Jing-Lin Kong, Dong-Mei Sun, Yu-Ying Feng, Hai-Yan Lu, Guang-Hou Wang

Journal of Electrochemistry

The porous alumina membrane formed in the anodic oxidation of highly pure aluminum foil has attracted a great deal of attention in recent years. It can be served as a desired template to prepare nanometer scale materials due to its unique structure of discrete and cylindrical nanopores, paralleled one another, with the homogeneous size and distribution. Chalcogenide semiconductors have promising prospect in the applications of photovoltaic and photoconducting devices and have been extensively exploited for many years. Olbright and his co-workers studied experimentally and theoretically the optical nonlinearties of CdS_xSe_1-x-doped glass; Britt and Ferekides reported that …

The Studies On Nanosized Materials For Lithium Ion Batteries, Hong Li, Jing-Ze Li, Li-Hong Shi, Guang-Yan Zhu, Qing Chen, Wei Lu, Xue-Jie Huang, Li-Quan Chen

Journal of Electrochemistry

Our recent works about nanosized materials for lithium ion batteries are reported, including the synthesis of nanosized Sb, SnSb, CuSn_x, Si and CuS, their electrochemical performance as anode or cathode active materials, the variation of crystal structure and morphology during discharge and charge cycling. In addition, the self-plasticization of lithium salt with nanosized anion ion in polymer electrolyte, the influence of the electrochemical Li-doping on the Raman spectra and photoluminescence of nano-Si are also introduced. Furthermore, the relationship between intrinsic properties of nanosized materials and their electrochemical behaviors are discussed. The prospect of nanosized materials for lithium ion …

Electrochemical Characterization Of Ir-Ta-Ti Metal Oxide Coated Titanium Anodes, Ting-Yong Wang, Li-Kun Xu, Guang-Zhang Chen

Journal of Electrochemistry

Ir-Ta-Ti metal oxide coated titanium anodes of variable composition were prepared by thermal decomposition. Their micro morphorogies and electrochemical properties were characterized by scanning electron microscope, open circuit potential, cyclic voltammetry, consumption rate measurements and accelerated life test. The SEM results indicated that all coatings were of a porous and cracked-mud microstructure influenced greatly by the composition of coatings. The electrochemical measurements showed that the Ir-Ta-Ti ternary oxide-coated anodes exhibited excellent electrochemical activity and electrochemical stability in both acidic media and seawater which were affected by the composition and microstructure of the coatings. Owing to good corrosion resistance and low …

Studies On Electrochemical Synthesis Of 4,5-Disubstituted-1,2- Benzoquinones And The Reaction Mechanism, Xian-Zhang Bu, Gui-Wu Xiao, Lin Ma, Xing-Chum He, Ling-Quan Gu

Journal of Electrochemistry

The oxidation peak potentials (E_p) of alinine derivates and catechol in 0.1 mol/L KCl+15% alcohol solution were measured by cyclic voltammograms technique. The electrochemical oxidation condition was set according to the E_p. Three derivates of 4,5-disubstituted -1,2-benzoquinones were prepared via electrochemical oxidation-Michael addition reaction. The possible mechanism of electrochemical oxidation-Michael addition reaction is presented.

Cathodic Indirect Electro-Oxidation——Organic Electro-Synthesis Dimethyl Sulfone, Deng-Ping Gu, Rui-Zhi Wang, Hong-Kun Zhang, Xue-Ying Zhang, Wei Li, Bao-Qiu Cui

Journal of Electrochemistry

A cathodic indirect electro-oxidation system was established for indirect electro-oxidize dimethyl sulfoxide to dimethyl sulfone with electro-eduction generated H₂O₂ catalyzed by the pertungstate/tungstate (WO₅^2-/WO₄^2-) redox mediator. Influences of current density, pH, temperature, and the current efficiencies etc. On the cathodic indirect electro-oxidation of dimethyl sulfone were investigated for determining optimum reaction conditions. The current efficiency reached more than 70%. Mother-liquid could be recycled to use without pollution.