Chemistry Commons^™

Electrochemical Studies On Electrocatalytic Activity Of AuCore PtShell Nanoparticles To Methanol Oxidation, Fang Bao, Jian-Lin Yao, Ren-Ao Gu

Journal of Electrochemistry

Au_corePt_shell nanoparticles with different thicknesses were prepared by using chemical reduction method,and characterized by ultraviolet-visible spectroscopy(UV-Vis),transmission electron microscopy(TEM) and cyclic voltammetry(CV).The electrocatalytic activity of Au_corePt_shell nanoparticles with the mean diameter of 70~80 nm to methanol oxidation was investigated by cyclic voltammetry in the acid solution.The results revealed that the prepared core-shell nanoparticles were covered by Pt shell and exhibited the similar optical property and electrocatalytic activity with the normal Pt surface.Moreover,the electrocatalytic activity increased with the electrochemical sweep in the certain potential range.It might be contributed by the special loose structure of Pt shell …

Electrochemical Behavior And Reduction Mechanism Of High Valence Silver Oxide Ag3O4 In Alkaline Solution, Yan Cheng, Ming Yu, Man-Ming Yan, Zhi-Yu Jiang

Journal of Electrochemistry

The electrochemical properties of high-valence silver oxide Ag₃O₄ in alkaline solution were investigated for the first time and the reduction mechanism of Ag₃O₄ was proposed. It can be recognized that Ag₃O₄ consists of Ag(Ⅲ) and Ag(Ⅱ)~(*). From the results of voltammetry and XRD experiments it was found that the reduction process of Ag₃O₄ was more complicated. It could be electrochemically reduced through the series reactions of Ag(Ⅲ) →Ag(Ⅱ) →Ag(Ⅰ) →Ag(O) at low discharge rate or Ag(Ⅲ) →Ag(Ⅰ) →Ag(O) at higher discharge rate.And the Ag(Ⅱ)~(*) could be reduced to …

2nd Annual Undergraduate Research Conference Abstract Book, University Of Missouri--Rolla

Undergraduate Research Conference at Missouri S&T

No abstract provided.

Electrocatalytic Oxidation Of Glucose On Nano Pt/C Electrode, Cui-Lian Chen, Xiao-Lan Wei, Pei Kang Shen

Journal of Electrochemistry

Nano Pt/C electrocatalysts were prepared by intermittent microwave heating method.The electrooxidation of glucose on smooth Pt and～Pt/C electrodes has been studied and compared.The results showed that the electrochemical properties on nano Pt/C were improved due to the reduction of the overpotential and the increase in the kinetic rate.The surface area would be significantly increased when the particle size of the catalyst was reduced to nano-scale,resulting in the increase in the activity.The enhancement in the resistance to poisoning could be explained that the oxygen-containing species are easier to react with poisoning species on nano Pt/C and re-active the electrode.

Electroless Nickel Plating On Carbon Nanotube With Non-Palladium Activation Procedure, Guang-Hui Hu, Hui-Huang Wu, Fang-Zu Yang

Journal of Electrochemistry

A new procedure of surface activation without using palladium salt was proposed for electroless nickel plating on carbon nanotubes.In the procedure,carbon nanotubes were oxidized by nitric acid and then neutralized with NaOH to create carboxyl surface groups which were used to adsorb Ni²⁺ ions,thereafter the adsorbed Ni²⁺ ions were chemically reduced into Ni nano-particles as a catalytic center for electroless nickel deposition,all these were further confirmed by infrared absorption spectra and electron microscopic observations.The results indicate that the procedure is feasible to electroless nickel plating on carbon nanotubes.The different morphology of deposits obtained from electroless plating was also …

Anodic Behaviors Of Pb-Ca-Sn-Re Alloy And Tradditional Pb-Ca-Sn Alloy In Sulfuric Acid Solutions, Dang-Guo Li, Gen-Shu Zhou, Liang Yao, Guan-Fa Lin, Mao-Sheng Zheng

Journal of Electrochemistry

The anodic behaviors of Pb-Ca-Sn-Re and Pb-Ca-Sn alloys were investigated at 1.28 V(vsHg/(H₂SO₄)) in 4.5 mol/L sulfuric acid solution by means of ac voltammetry,ac impedance and cyclic voltammetry.The results showed that the corrosion-resistance property of Pb-Ca-Sn-Re alloy is better than that of tradditional Pb-Ca-Sn alloy,the growth of Pb(Ⅱ) compounds was inhibited in the film of Pb-Ca-Sn-Re alloy,and the film impedance of Pb-Ca-Sn-Re alloy was decreased,indicating that the conductivity of the film was(increased),which is helpful to enhance the deep recycling property for lead acid battery.

The Effect Of Solution Concentration On Properties Of Ru-Ti-Ir Oxide Anode Coatings, Ke Wang, Yan Han, Jun-Tao Wang, Xiao-Ling Zhang, Yu-Pu Sun

Journal of Electrochemistry

The anode coatings of Ru-Ti-Ir oxide with various solution concentrations were prepared by thermal decomposition.The scanning electron microscope(SEM),energy dispersive X-ray detector(EDX),X-ray diffraction(XRD),accelerated life,polarization curve,cyclic voltammetry and electrochemical impedance.spectroscopy(EIS)tests were carried out.The results showed that there was an obvious effect of solution concentrations on the morphology of the coatings,but little effect on polarization of chlorine evolution.Voltammetric charges and double layer capacitances of anode coatings had a tendency to fall down firstly then increase afterwards as the solution concentration increased.

Mechanism Of Self Discharge Performance Improvement In The Ni-Mh Batteries With Naoh Electrolyte, Xiao-Feng Li, Tong-Chi Xia, Hui-Chao Dong, Yan-Wei Wei

Journal of Electrochemistry

The self-discharge performance and charge efficiency at 60 ℃ for Ni-MH battery can be markedly enhanced by using NaOH electrolyte instead of KOH electrolyte.Both the results of electrochemical impedance spectroscopy and cyclic voltammetry tests indicate that the separation of H₂ from the negative electrode may be partly blocked in the former because of the change of the adsorption/desorption behavior of H on the surface of the negative electrode,thus results in an improvement of self-discharge performance of the battery.

Oxygen Enrichment Effect Of Ceo2 To The Cathode Performance Of Proton Exchange Membrane Fuel Cell, Xiang-Li Hou, Hong-Feng Xu, Jian-Hua Dong, Xin Sun

Journal of Electrochemistry

CeO₂ was added to Pt/C catalyst in the cathode of PEMFC by both sol and impregnation methods.The samples were evaluated by TEM,cyclic voltammogram techniques and proton exchange membrane fuel cell performance test.The addition of CeO₂ obviously improved the performance of PEMFC and represented a notable function of oxygen enrichment in the cathode side.But with the addition of CeO₂,part of the catalyst surface was covered and led to the performance drop of the PEMFC.The best content of CeO₂ is 1% when it is added by impregnation method and 3% when it is added by sol method.

Special Photoelectrochemical Response Of Nano-Crystalline Tio2 Electrode, Bi-Bo Lan, Jian-Zhang Zhou, Yan-Yan Xi, Hong-Xiang Chen, Guang-Hua Yao, Zhong-Hua Lin

Journal of Electrochemistry

The nano-crystalline TiO₂ electrodes were prepared by spread method,electrodeposition and sol-gel method.The experimental results show that the nano-crystalline TiO₂ electrodes have special photoelectrochemical response-the photocrrent-potential curves appear peaks.The special photoelectrochemical behaviors of nano-(crystalline) TiO₂  electrodes are ascribed to nano-structure as well as special light induced redox reaction mechanism of nano-crystalline semiconductor electrodes.

Degradation Of Aniline Wastewater By Electro-Heterogeneous Catalysis Reactor, Wei-Li Liu, Ai-Li Zhang, Ji-Ti Zhou, Bao-Jun Jia, Qun-Li Zhu

Journal of Electrochemistry

The treatment of aniline wastewater was investigated using novel electro-heterogeneous catalysis reactor.The effects of applied cell voltage,electrolysis lime,pH value and the electrolyte on electrolysis were investigated.The experimental results show that the reactor with a cell voltage of 30 V,an electrolysis time of 1 h,pH value of 7 and a salinity of 800 mg/L can achieve the best removal efficiency on aniline,which is more efficient than the sole electrochemical reactor.

Electrochemical Reduction Behavior Of Benzaldehyde In The Ionic Liquids, Ning Zhao, Wen-Ju Dong, Qi-Zeng Shi

Journal of Electrochemistry

In this paper, the electrochemical reduction of benzaldehyde was investigated in C₄MIMBF₄, C₆MIMBF₄  and C₈MIMBF₄ ionic liquids by cyclic linear sweep voltammetry,cyclic square-wave voltammetry and chronocoulometry.Benzaldehyde exhibits two successive one-electron irreversible reduction(E_P1=-1.39 V, E_P2=1.69 V) with GC electrode in C₄MIMBF₄, the voltammetric data for benzaldehyde give diffusion coefficients of 1.5*10^-8cm²/s and 1.3*10⁸cm²/s. There is one current peak in C₆MIMBF₄  and C₈MIMBF₄ ionic liquids due to their stronger alkalinity …

Effects Of Srb Biofilm And Corrosion Product Films On Corrosion Behavior Of Carbon Steel, Jing Lin, Yong-Gui Yan, Guang-Zhang Chen, Guang-Zhou Liu, Qing-Fen Li

Journal of Electrochemistry

Electrochemical techniques and surface analysis techniques were applied to study corrosion characteristic of A₃ steel.The effects on corrosion behavior of A₃ steel by sulfate-reducing bacteria(SRB)(biotic media)and corrosion product(abiotic media)were studied.The results showed that biofilms and corrosion product films play different role during different stages.Biofilms were easier flaky with increasing of its thickness.Non-uniform biofilms reduced pitting corrosion of the specimens.The corrosion product films formed under abiotic conditions were more adherently to the surface of the metal than those formed in biogenic media.

Preparation Of Spinel Limn2O4 Cathode Materials For Li-Ion Batteries Based On Sol-Gel Process, Xiang-Ming He, Li Wang, Guo-Yun Zhang, Chang-Yin Jiang, Chun-Rong Wan

Journal of Electrochemistry

Spinel LiMn₂O₄ was prepared from CH₃COOLi·2H₂O,Mn(CH₃COO)₂ and adipic acid based on sol-gel process.XRD analysis showed that when the sintering temperature increased,the crystallinity increased,and the capacity also increased.However,its cycleability reached a maximum value at 750 ℃.The sintering duration also influenced on the capacity.The optimized performance was obtained when the sintering was carried out at 750 ℃ for 20 h.Under these conditions,as-prepared spinel LiMn₂O₄  presented the initial discharge capacity of 130 mAh·g^-1 and 125 mAh·g^-1 at 15^th cycle.

Nanodot-Based Organic Memory Devices, Zhengchun Liu

Doctoral Dissertations

In this study, resistor-type, diode-type, and transistor-type organic memory devices were investigated, aiming at the low-cost plastic integrated circuit applications. A series of solution-processing techniques including spin-coating, inkjet printing, and self-assembly were employed to fabricate these devices.

The organic resistive memory device is based on a novel molecular complex film composed of tetracyanoquinodimethane (TCNQ) and a soluble methanofullerene derivative [6,6]-phenyl C61-butyric acid methyl ester (PCBM). It has an Al/molecules/Al sandwich structure. The molecular layer was formed by spin-coating technique instead of expensive vacuum deposition method. The current-voltage characteristics show that the device switches from the initial 'low' conduction state to …

Growth Of Ge Quantum Dots On Si(100)-(2×1) By Pulsed Laser Deposition, M. S. Hegazy, H. E. Elsayed-Ali

Electrical & Computer Engineering Faculty Publications

Self-assembled germanium quantum dots (QDs) were grown on Si(100)-(2×1) by pulsed laser deposition. In situ reflection-high energy electron diffraction (RHEED) and postdeposition atomic force microscopy are used to study the growth of the QDs. Several films of different thicknesses were grown at a substrate temperature of 400 °C using a Q-switched Nd:yttrium aluminum garnet laser (λ= 1064 nm, 40 ns pulse width, 23 J/cm ² fluence, and 10 Hz repetition rate). At low film thicknesses, hut clusters that are faceted by different planes, depending on their height, are observed after the completion of the wetting layer. With increasing film thickness, …

Atr-Ftir Spectroscopic Analysis Of Sorption Of Aqueous Analytes Into Polymer Coatings Used With Guided Sh-Saw Sensors, Yolanda K. Jones, Zhonghui Li, Michael M. Johnson, Fabien Josse, Jeanne Hossenlopp

Chemistry Faculty Research and Publications

Attenuated total internal reflectance Fourier transform infrared (ATR-FTIR) spectroscopy was used for the investigation of sorption of aqueous solutions of analytes into polymer coatings. A series of simple model polymers, such as poly(dimethylsiloxane), poly(epichlorhydrin), and poly(isobutylene), and films and analytes, such as aqueous solutions of ethylbenzene, xylenes, toluene, and nitrobenzene, were used to evaluate the use of ATR-FTIR spectroscopy as a screening tool for sensor development. The ratios of integrated infrared absorption bands provided a simple and efficient method for predicting trends in partition coefficients. Responses of polymer-coated guided shear horizontal surface acoustic wave (SH-SAW) sensor platforms to the series …

A Study Of Overcharge Characteristic Of Lithium-Ion Cells, Jing Pang, Shi-Gang Lu, Sha Liu

Journal of Electrochemistry

The overcharge characteristics and effect factors of lithium-ion cells containing LiMn₂O₄ cathodes were studied in detail. Overcharge testing of Lithium-ion cells with a systematic variation in the cell balance demonstrated that the overcharge characteristics of Lithium-ion cells was affected by the amount of cathode in the cells, which is independent of the amount of anode material. The rate of charge was found to be an important parameter, as electrolyte complete decomposition at low charge rates caused the end of overcharge testing, while high charge rates accelerated the rate of heat generation in the cells and the cell …

The Deactivation Mechanism Of Metal Oxide Anodes Under Alternative Current Electrolysis Condition, Jun-Tao Wang, Yan Han, Guang-Zhang Chen, Wen-Fa Liu

Journal of Electrochemistry

The metal oxide anodes coated on titanium used in seawater electrolysis were prepared by thermal decomposition. Their morphologies, compositions and phase structures were determined by scanning electron microscope(SEM), energy dispersive X-ray detector(EDX) and X-ray diffraction(XRD). The electrochemical properties of the anodes were characterized by accelerated life test, cyclic voltammetry and electrochemical impedance spectroscopy. SEM, EDX and XRD showed that solid solution structures of (Ru, Ir, Ti)O₂ and (Ir, Ti)O₂ were formed after pyrolysis, the solid solution structures and active components were disappeared after the deactivation of the anodes. Electrochemical results indicated that the active area decreased and the …

Silicides And Composites Materials As Anodes For Lithium Ion Batteries, Jun-Mei Yan, Hui-Zhen Huang, Jing Zhang, Yong Yang

Journal of Electrochemistry

The anode materials of Mg₂Si and MnSi were synthesized by mechanically activated annealing(MAA) techniques in this work and the in electrochemical performances were also studied.A series of composite materials of Mg₂Si and CNTs or CMS were prepared by ball-milling method respectively. The reversible capacities of the composites were higher than that of the pure Mg₂Si and pure carbon materials.The cyclic performances have been improved greatly by ball-milling of the Mg₂Si and carbon materials. Results show that ball-milling method is one kind of method to make alloy materials into practical use.

A Continuous Operation For Electroreduction Of Oxalic Acid To Glyoxylic Acid, Xiao-Hui Hu, Xiang-Fei Yan, Yu-Zhong Su, Jun Li, Qing-Biao Li

Journal of Electrochemistry

A simulative-continuous-operation approach was proposed to study the continuous operation for electroreduction of oxalic acid to gloxylic acid using a packed bed reactor and a parallel reactor with cooled cathode in order to solve the low productivity problem in current state by using traditional reactor. The effects of the concentration of oxalic acid and temperature on this process were also studied. Results showed that,after 30min of the reaction(residence time), the mass fraction of the produced glyoxylic acid in the catholic solution could reach 3.76% and 3.66% with respect to a saturated oxalic acid method and a step-temperature decreasing method. From …

The Optimal Sulfonation Conditions Of Self-Doped Polyaniline Obtained By Using Experimental Strategies, Wen-Yar Li, Chi-Chang Hu

Journal of Electrochemistry

The optimal sulfonation condition of self-doped sulfonated polyaniline (prepared from leucoemeraldinebase; denoted as LEB-SPANI) with a high electronic conductivity was obtained by experimental strategies, includingthe fractional factorial design (FFD) and central composite design (CCD). From the FFD experiment, the self-doped LEB-SPANI prepared at a lowtemperature (4℃), a short reaction time (1 h), and a small volume of fumingsulfuric acid (10 mL) showed a better conductivity (ca.127 mS/cm). In the CCD study coupled with a confirmationtest, the highest conductivity (ca.141 mS/cm) of the LEB-SPANI film was obtained under a sulfonation temperatureof 4℃, a sulfonation time of 75 minutes, and a volume …

Electrochemical Oxidation Of Organic Additives In Tin Plating Electrolytes, Yin-Mei Cheng, Lan-Kun Cai, Qiang Song

Journal of Electrochemistry

Cyclic voltammetry(CV) was used to characterize the voltammetric behaviours of organic additives, e.g. PSA(phenolsulfonic acid) EN(ethoxylatedα-naphthol) and ENSA(ethoxylatedα-naphthol sulfonic acid), on the anode surface. In PSA solutions, an anodic peak was obtained and the peak potential was about 1.2V. In EN and ENSA solutions, two anodic peaks were obtained and the peak potentials were about(0.95V) and 1.3V. The products of galvanostatic electrolysis were separated by HPLC(high performance liquid chromatography) and analyzed by EI/MS(electron ionizing mass spectrometry). The mechnism of the electrochemical oxidation was also disussed.

The Electrocatalystic Investigation Of 3,4-Dihydroxybenzoic Acid On The Modified Multiply Wall Carbon Nanotubes, Ming-Qi Li, Duo-Chang Cai, Xiao-Ying He

Journal of Electrochemistry

The electrochemical behavior of 3,4-Dihydroxybenzoic acid(DHBA) on modified multiply wall carbon nanotubes electrode was investigated by cyclic voltammetry(CV) and square wave voltammetry(SWV). Results show that in 0.1 mol/L HCl solutions the modified carbon nanotube electrode has an obvious electrocatalytic effect on the oxidation and deoxidization of DHBA. The oxidation current of DHBA is linear to it's concentration in the range of 4.0×10^-6～1.0×10^-4 mol/L and 2.0×10^-4～8.0×10^-4 1mol/L with correlation coefficient of 0.9995 and 0.9992. The detection limit is 1.0×10^-6 mol/L.

Solid Oxide Fuel Cells-Materials And Prospects, Molenda Janina, Marzec Jacek

Journal of Electrochemistry

The paper summarizes and discusses the basic properties of solid oxide fuel cell (SOFC) components (electrode materials and electrolyte) from the point of view of their essential functional parameters suck as chemicalstability, transport, catalytic and thermomechanical properties under operational conditions in a SOFC. An interrela-tion between the defect structure of these materials related to oxygen nonstoichiometry and their electronic propertiesand catalytic activity was shown. Single-chamber fuel cell concept was also presented.

Nafion Emulsion Method For Fuel Cell Membrane-Electrode-Assembly Preparation, Chao-Yang Xia, Lin Zhuang, Jun-Tao Lu

Journal of Electrochemistry

A Nafion emulsion method for fuel cell membrane-electrode-assembly (MEA) preparation was reported for the first time in this paper. 5 %(by mass) Nafion alcohol solution and non-polar solvent (e.g., cyclohexane) were ultrasonicallymixed to produce Nafion emulsion. The catalyst ink prepared using the thus-obtained Nafion emulsion can be directly cast onto Nafion membrane to make MEA. This method is simple in operation, and effectively preventsthe Nafion membrane swelling, hence is suitable for large-scale application. The MEA thus-prepared showed comparable catalyst efficiencywith respect to the popular transfer-method, and the preliminary performance in room-temperature H₂/O₂ fuel cell test was satisfying.

Adsorption Of Polyaspartic Acid From Sulphur Acid Solution On Carbon Steel And Its Corrosion Inhibition, Rong-Jing Cui, Ning Gu, Chun-Mei Li

Journal of Electrochemistry

The role of Polyaspartic acid in the corrosion inhibition of 45# carbon steel in sulphuric acid solution has been investigated by polarization curve andelectrochemical impedance spectroscopy (EIS). The influences of the concentration and the temperature of PASP on the corrosion inhibition efficiency were determined. The results indicated that the PASP as the corrosion inhibitor mainly inhibitated the anode; within the experiment temperature, the inhibitor efficiency decreased with the raising of the temperature and PASP had a good inhibiting performance at 10℃, the corrosion inhibition efficiency of PASP for carbon steel increased with the increase of the concentration of PASP when …

Electrocatalytic Oxidation And Degration Of Active Red X-3b By Nanotubes Catalytic Electrodes, Yi Wen, Jian-Hui Fang, Wei-Min Cao, Li-Yi Shi

Journal of Electrochemistry

The catalytic splitting decomposition of carbon nanotubes isprocessed by dispersing with dilute nitric acid and thermal oxidation. Then well-proportionedphenolic resin is mixed in the carbon nanotubes. Then, the carbon nanotubesare made into electrodes by hot-press molding after the process of milling with high speed. The surface of the carbon nanotubes electrodes is analyzed by SEM. Active red X-3B simulated waster water is disposed by carbon nanotubes catalyticelectrode (anode) and stainless steel(cathode). The influencing factors of degradation by current density, concentrationof electrolyte, systemtemperature and pH are investigated. The experimental results indicated that acidiccondition is propitious tothe degradationreaction of organicdyestuff and wastewater …

Electrochemical Reduction Characteristics Of Nitrobenzene At The Copper Electrode, Jin-Hong Fan, Wen-Ying Xu, Ting-Yao Gao

Journal of Electrochemistry

The electrochemical reduction characteristics and transition steps of nitrobenzene aqueous solution at the copper electrode, as well as its reduction mechanism were extensively investigatedby using the techniques such as cyclic voltammetry (CV) and linear scan voltammetry (LSV). The results showed that the reduction peaks of nitrobenzene at the copper electrode were located at 0.58 V and 1.32 V or so (vs. SCE), both acidity and alkalinesolutionsfavoredthe reduction of nitrobenzene. The adsorption of compounds followed by the reduction process, which is controlled by the mass transfer step at higher nitrobenzene concentration. In addition, the higher anaerobic degree led to faster reduction …

Research Progresses In A Flow Redox Battery, Quan-Feng Dong, Hua-Min Zhang, Ming-Gang Jin, Ming-Sen Zheng, Ya-Ding Zhan, Shi-Gang Sun, Zu-Geng Lin

Journal of Electrochemistry

As a large scale electrochemical storage device, flow redox battery in which the active materials are flowing electrolytes is different from the common batteries employing solid or gas materials as an electrode. In this paper we introduced flow redox battery in brief, reviewed its development and actual state on (study). The main problem existed in the new device was discussed when viewed with its future developments.