Numerical Analysis and Computation Commons^™

Pseudodifferential Absorbing Boundary Conditions For Waves, Lauren Taylor

Mechanical Engineering Theses

Absorbing boundary conditions (ABCs) are required to truncate the computational domain when performing Finite Element Analyses of exterior acoustic problems where physical domain is unbounded. ABC is applied on a fictitious boundary containing the scatterer and ideally allows outgoing waves to leave without non-physical reflections. Preventing artificial reflections is essential to benefit from the accuracy of the numerical method used. Otherwise, ABC acts as a reflective surface, and artificial reflections distort the solution in the entire domain which is not recoverable by any type of refinement. Pseudodifferential ABCs were used to describe the Dirichlet-to-Neumann map which maps known boundary values …

Hybrid Solar - Coal Thermal Energy System For Industrial Process Heat At Sayona Drinks Limited In Tanzania, Santos Kihwele, Elisha D. Bitesigirwe

Tanzania Journal of Engineering and Technology (TJET)

Over the past two decades, global efforts to mitigate pollution from conventional energy sources have intensified, with coal remaining a major contributor to carbon emissions. While fossil fuels cannot be eliminated from thermal generation in manufacturing industries, particularly in middle‑income countries such as Tanzania, they continue to dominate as the primary energy source. Industries including food and beverage, paper, textile, paints, chemicals, and pharmaceuticals require substantial thermal energy for heating and drying, and typically rely on coal and natural gas.This study introduces a unique application of a parabolic trough solar thermal system with integrated thermal energy storage, specifically tailored to …

Safe Control Design For Quadruped Locomotion In Unstructured Environments Using Linear Transfer Operators, Sriram Sundar Krishnamoorthy Shankara Narayanan

All Dissertations

Deploying quadruped robots in unstructured, obstacle-rich environments requires control and planning methods that remain safe and reliable despite complex terrain geometry, limited sensing, and inevitable modeling errors. This thesis develops operator-theoretic tools for safe control design of robotic systems using linear transfer operators, with a focus on quadruped locomotion in unstructured environments. The central goal is to develop a unified operator-theoretic framework for safe control design based on the Perron–Frobenius (P–F) and Koopman operators. In particular, the thesis leverages \emph{density functions} to develop safe navigation frameworks in the dual space of densities. In the operator-theoretic perspective, the P–F operator governs …

Microgravity-Induced Alterations In Left Atrial Hemodynamics And Thrombogenic Risk: Insights From Healthy And Atrial Fibrillation Models, Grace M. Hoeppner

Dissertations, Master's Theses and Master's Reports

Background: Microgravity exposure alters cardiovascular loading, yet its impact on left atrial flow dynamics and thrombotic risk remains poorly understood. This study investigates how spaceflight-relevant microgravity-induced changes in cardiac outflow affect left atrial hemodynamics in healthy individuals and patients with atrial fibrillation.

Methods: Patient-specific left atrial models were generated for three healthy individuals and three AF patients. Computational fluid dynamics (CFD) simulations were performed using each patient’s baseline mitral outflow waveform and two modified waveforms representing short- and long-duration post-flight cardiac loading changes derived from echocardiographic observations. Hemodynamic metrics included left atrial velocity, time averaged wall shear stress, oscillatory shear …

Universal Systems Simulation Via Constraint Hypergraphs With Applications To Digital Twins, John Morris

All Dissertations

The characterization of systems encompasses a variety of modeling frameworks designed to capture specific behaviors and components of various system domains. Whatever the framework, the core elements of a system representation are the information of the system and a description of how that information is related. The relations in deterministic systems are functions, which, when composed to form executable processes, can be used to simulate system data. A declarative modeling framework is one that encodes mechanisms for preparing these simulations within the model structure, allowing an external agent to form the execution processes required for a given context. To date, …

Fuzzy-Ahp Based Decision Support System For The Selection Of Optimal Maintenance Strategy For Meter Gauge Railway Infrastructure: A Review, Hamisi J. Maulid

Tanzania Journal of Engineering and Technology (TJET)

There are many uncertainties and complexities associated with maintaining Meter Gauge Railway (MGR) infrastructure, which calls for a methodical approach to decision-making. The development and application of a fuzzy-AHP-based decision support system (DSS) to select the optimal maintenance strategy for the MGR are presented in this study. The review covers research from 2013 to 2023 and focusses on the use of Multi-Criteria Decision Making (MCDM) and Fuzzy Analytic Hierarchy Process (Fuzzy-AHP) techniques in railway infrastructure maintenance. To manage the inherent uncertainties and subjective judgements involved in maintenance decision-making, the Fuzzy-AHP methodology combines fuzzy logic with the Analytic Hierarchy Process (AHP). …

The Role Of Internal Factors On Vehicular Mobility, Aziz Mdimi

Tanzania Journal of Engineering and Technology (TJET)

Vehicle mobility internal factors are influenced by the performance state of the road surface quality, governor, engine, gear train, differential unit and mobility unit. Studies on vehicular mobility models exist for off-road external factors but absent on on-road internal factors. The on-road internal factors model describes the vehicular mobility performance as a function of internal factors. In the current undertaking, results are generated by the determination of mobility performance characteristics with the application of 2nd Order Ordinary Differential Equations and using Laplace operator with MATLAB Software simulation. The effect of road surface against the time taken varies accordingly. At a …

Review On Gas-To-Liquids Conversion Technology: Lessons From Case Studies And Potential Strategies For Implementation In Tanzania, Joseph H. Kihedu

Tanzania Journal of Engineering and Technology (TJET)

This review paper explores the transformative potential of Gas-to- Liquids (GTL) technology for harnessing Tanzania's vast natural gas resources. With significant discoveries of natural gas reserves totalling up to 57 Tcf in fields such as Songosongo, Mnazi Bay, Block 1, 2, 3 and 4. Tanzania is positioned to leverage GTL technology to convert these resources into high-value liquid fuels like gasoline, diesel and naphtha. Review of GTL process, its products and applications has been done. By analysing successful GTL projects globally and drawing lessons applicable to Tanzania, this paper provides strategic recommendations for policymakers and stakeholders to foster GTL development. …

Fuzzy Logic-Based Decision Support System For Adoption Of Industry 4.0 Predictive Maintenance By Manufacturing Industries, Fred E. Peter

Tanzania Journal of Engineering and Technology (TJET)

In the context of Industry 4.0, predictive maintenance enhances operational efficiency by optimizing processes, minimizing downtime, and improving cost-effectiveness. However, implementing predictive maintenance requires a systematic approach due to its complexity. This study collected expert input from 15 food and beverage manufacturing industries located in Dar es Salaam, Tanzania, using a purposive sampling technique. Six representatives were selected from each industry, and their opinions were analyzed using MATLAB 7.6 through a fuzzy logic inference system. The analysis focused on key factors influencing Industry 4.0 technology adoption for predictive maintenance, including adoption intention (strategic decision, equipment data, perceived benefit) and perceived …

Performance Studies Of An Axial Flow Waterjet Pump Using An Unsteady Reynolds-Averaged Navier-Stokes Model, Stephen E. Monroe, Junfeng Wang, Chunlei Liang

Northeast Journal of Complex Systems (NEJCS)

In this study, an Unsteady Reynolds-Averaged Navier-Stokes (URANS) model is demonstrated its suitability for studying the flow and performance of open marine propellers and waterjet pumps. First, the accuracy of the URANS model is validated by studying turbulent flow past counter-rotating propellers (CRPs). Specifically, experimental data from Miller (1976) is employed for comparison against the URANS results. Subsequently, URANS is used to study the flow and performance of an Office of Naval Research (ONR) axial flow waterjet pump (AxWJ-2). Due to the large number of degrees of freedom for both simulations, parallel computations over 80 cores are performed. For the …

Evaluation Of Business-Driven Reference Architecture For Big Data Analytics Implementation By Public Sector Organizations In Resource-Constrained Setting: A Case Study Of Uganda, Matendo Didas

Tanzania Journal of Engineering and Technology (TJET)

Big Data Analytics (BDA) is a new area at the nexus of agenda, public sector organizations, and government business. It may satisfy the growing need for trustworthy, cost-effective services in the public sector for better, more informed decision-making processes. BDA has been proposed on the planning schedules of several public sector organizations and the government. Therefore, from the previous work, using Uganda as a case study, specifically the Uganda Bureau of Statistics (UBOS), Ministry of Health (MoH), and Ministry of Education and Sports (MoES), this study aims to evaluate a designed Business-Driven Reference Architecture for Big Data Analytics Implementation (BRABDAI) …

Assessing The Importance Of Air-Decking Blasting In Controlling Bigv At An Open Pit Gold Mine In Tanzania Using Ann Model, Karim R. Baruti

Tanzania Journal of Engineering and Technology (TJET)

Air-decking blasting technique is used to control blast induced ground vibration (BIGV) in several mines including open-pit gold mines located in Tanzania. While the importance of air-deck to control BIGV is practically evident, theoretical models such as BIGV prediction models cannot be used to assess the importance of air-decking. The main objective of this study was to assess the importance of the air-decking blasting technique to control BIGV using the artificial neural network (ANN)Model. To achieve this objective, ANNs were modeled and trained to learn the pattern of data using Multilayer Perception with Back Propagation to predict BIGV. The main …

Optimization Pump As Turbine Coupled To A Self-Excited Induction Generator Using Multi-Objective Genetic Algorithm, Emanuel J. Nyirenda

Tanzania Journal of Engineering and Technology (TJET)

As a way of accelerating the deployment of affordable and clean renewable energy generation technologies, applying a pump working as a turbine coupled to a self-excited induction generator is gaining popularity in various areas including energy recovery and micro hydro systems. However, it is currently challenging to predict the performance of the PAT-SEIG system and there is no agreed-upon rule on the selection of the appropriate system to be installed at a particular site. This paper has presented multi-objective optimization to select the best operating point of the PAT-SEIG system. The results show that the peak efficiencies for the PAT …

Optimal Load Shedding During Service Restoration In Electrical Secondary Distribution Network Based On Reinforcement Learning, Rukia J. Mwifunyi

Tanzania Journal of Engineering and Technology (TJET)

Increased stress in traditional power systems results in blackouts due to voltage instability attributed to a mismatch between available capacity and load demand, especially in distribution networks. Service restoration schemes are designed to return power supply to the affected parts of the networks. The availability of insufficient supply is a complex problem that requires operational experience or an automatic system. The stochastic nature of load demand significantly impacts service restoration as it results in increased restored demand in case a fault occurs during off-peak hours and helps reduce overload if the fault occurs during peak hours. The study adopts an …

Mathematical Modeling Of Coupled Heat And Mass Transfer In Metal-Hydride Hydrogen Storage Systems, Muhammad Hasnain

College of Graduate Studies: Theses & Dissertations

As a promising clean energy carrier hydrogen has recently gained significant interest, but its efficient and safe storage is a major challenge. Compared to the gaseous state and liquid state, metal hydrides (MH) offer a potentially more effective storage approach for hydrogen. However, the main challenge in this approach is the low thermal conductivity of the MH bed that leads to low heat transfer and ultimately to higher charging and discharging times. The purpose of this work is to develop an in-house comprehensive heat and mass transfer model for hydrogen sorption in MH reactors to simulate the dynamic behavior of …

Numerical Modeling Of Thermal Runaway In Lithium-Ion Batteries Using Decomposition Kinetics And Inter-Cell Contact Resistance, Shehzad Khan

College of Graduate Studies: Theses & Dissertations

Lithium-ion batteries (LIBs) are central in numerous high-demand applications due to their high energy density and prolonged cycle life. Despite these advantages, their susceptibility to thermal runaway (TR) poses a significant safety risk, with the potential for catastrophic failures. This study focuses on the thermal behavior of prismatic lithium-ion cells, using a finite volume-based partial differential equation (PDE) solver developed in MATLAB and JULIA to model TR behavior. This solver accurately simulates transient behaviors, convection, diffusion, and source terms across various coordinate systems. By engaging in a series of increasing complex case studies, this research aims to identify the critical …

Simulation Of Wave Propagation In Granular Particles Using A Discrete Element Model, Syed Tahmid Hussan

College of Graduate Studies: Theses & Dissertations

The understanding of Bender Element mechanism and utilization of Particle Flow Code (PFC) to simulate the seismic wave behavior is important to test the dynamic behavior of soil particles. Both discrete and finite element methods can be used to simulate wave behavior. However, Discrete Element Method (DEM) is mostly suitable, as the micro scaled soil particle cannot be fully considered as continuous specimen like a piece of rod or aluminum. Recently DEM has been widely used to study mechanical properties of soils at particle level considering the particles as balls. This study represents a comparative analysis of Voigt and Best …

Reducing Food Scarcity: The Benefits Of Urban Farming, S.A. Claudell, Emilio Mejia

Journal of Nonprofit Innovation

Urban farming can enhance the lives of communities and help reduce food scarcity. This paper presents a conceptual prototype of an efficient urban farming community that can be scaled for a single apartment building or an entire community across all global geoeconomics regions, including densely populated cities and rural, developing towns and communities. When deployed in coordination with smart crop choices, local farm support, and efficient transportation then the result isn’t just sustainability, but also increasing fresh produce accessibility, optimizing nutritional value, eliminating the use of ‘forever chemicals’, reducing transportation costs, and fostering global environmental benefits.

Imagine Doris, who is …

Controlled Manipulation And Transport By Microswimmers In Stokes Flows, Jake Buzhardt

All Dissertations

Remotely actuated microscale swimming robots have the potential to revolutionize many aspects of biomedicine. However, for the longterm goals of this field of research to be achievable, it is necessary to develop modelling, simulation, and control strategies which effectively and efficiently account for not only the motion of individual swimmers, but also the complex interactions of such swimmers with their environment including other nearby swimmers, boundaries, other cargo and passive particles, and the fluid medium itself. The aim of this thesis is to study these problems in simulation from the perspective of controls and dynamical systems, with a particular focus …

Computational Modeling Using A Novel Continuum Approach Coupled With Pathway-Informed Neural Networks To Optimize Dynein-Mediated Centrosome Positioning In Polarized Cells, Arkaprovo Ghosal, Padmanabhan Seshaiyar Dr., Adriana Dawes Dr., General Genomics Inc.

Annual Symposium on Biomathematics and Ecology Education and Research

No abstract provided.

A Robust Model Reduction For The Optimal Boundary Feedback Stabilization Of Magnetizable Piezoelectric Beams, Md Rafi As Sadeq Ibn Emran

Masters Theses & Specialist Projects

The one-dimensional Partial Differential Equation (PDE) model of the wave equation, which describes wave dynamics of a wide-range of controlled mechanical systems, with a state feedback controller at its boundary is known to have exponentially stable solutions. Moreover, it is also reported that the several model reductions of the wave equation by the standard Finite Differences and Finite Elements approximations suffer from the lack of exponential stability (and exact observability without a state feedback controller) uniformly as the discretization parameter tends to zero. This is due to the loss of a uniform gap among the high-frequency eigenvalues as the discretization …

Modeling, Simulation And Control Of Microrobots For The Microfactory., Zhong Yang

Electronic Theses and Dissertations

Future assembly technologies will involve higher levels of automation in order to satisfy increased microscale or nanoscale precision requirements. Traditionally, assembly using a top-down robotic approach has been well-studied and applied to the microelectronics and MEMS industries, but less so in nanotechnology. With the boom of nanotechnology since the 1990s, newly designed products with new materials, coatings, and nanoparticles are gradually entering everyone’s lives, while the industry has grown into a billion-dollar volume worldwide. Traditionally, nanotechnology products are assembled using bottom-up methods, such as self-assembly, rather than top-down robotic assembly. This is due to considerations of volume handling of large …

Novel Bayesian Neural Networks And Uncertainty Quantification Of Computational Mechanics Models, Ponkrshnan Thiagarajan

Dissertations, Master's Theses and Master's Reports

Computational and data-driven models suffer from a wide range of uncertainties that impact the reliability of such models. Given the exponential proliferation of machine learning models in real-world systems, establishing a degree of confidence in their predictions becomes paramount. Reliability in predictions takes on utmost significance in domains such as autonomous driving, medical image analysis, etc., where human lives are involved, and inaccuracies in predictions could lead to disastrous outcomes. For these reasons, comprehending and quantifying uncertainties in computational and data-driven models is of utmost importance. A number of techniques have been developed to quantify uncertainties in machine learning models. …

Impact Of Spallation And Internal Radiation On Fibrous Ablative Materials, Raghava Sai Chaitanya Davuluri

Theses and Dissertations--Mechanical and Aerospace Engineering

Space vehicles are equipped with Thermal Protection Systems (TPS) that encounter high heat rates and protect the payload while entering a planetary atmosphere. For most missions that interest NASA, ablative materials are used as TPS. These materials undergo several mass and energy transfer mechanisms to absorb intense heat. The size and construction of the TPS are based on the composition of the planetary atmosphere and the impact of various ablative mechanisms on the flow field and the material. Therefore, it is essential to quantify the rates of different ablative phenomena to model TPS accurately. In this work, the impact of …

Optimal Design Of Bacterial Carpets For Fluid Pumping, Minghao W. Rostami, Weifan Liu, Amy Buchmann, Eva Strawbridge, Longhua Zhao

Biology and Medicine Through Mathematics Conference

No abstract provided.

A Meshless Approach To Computational Pharmacokinetics, Anthony Matthew Khoury

Doctoral Dissertations and Master's Theses

The meshless method is an incredibly powerful technique for solving a variety of problems with unparalleled accuracy and efficiency. The pharmacokinetic problem of transdermal drug delivery (TDDD) is one such topic and is of significant complexity. The locally collocated meshless method (LCMM) is developed in solution to this topic. First, the meshless method is formulated to model this transport phenomenon and is then validated against an analytical solution of a pharmacokinetic problem set, to demonstrate this accuracy and efficiency. The analytical solution provides a locus by which convergence behavior are evaluated, demonstrating the super convergence of the locally collocated meshless …

Numerical Investigation On The Effect Of Spectral Radiative Heat Transfer Within An Ablative Material, Raghava S. C. Davuluri, Rui Fu, Kaveh A. Tagavi, Alexandre Martin

Mechanical Engineering Faculty Publications

The spectral radiative heat flux could impact the material response. In order to evaluate it, a coupling scheme between KATS - MR and P1 approximation model of radiation transfer equation (RTE) is constructed and used. A Band model is developed that divides the spectral domain into small bands of unequal widths. Two verification studies are conducted: one by comparing the simulation computed by the Band model with pure conduction results and the other by comparing with similar models of RTE. The comparative results from the verification studies indicate that the Band model is computationally efficient and can be used to …

Socio-Technical Perspective For Electronic Tax Information System In Tanzania, Lucas Ngowi, Ellen Kalinga

Tanzania Journal of Engineering and Technology (TJET)

Socio-technical systems theory has rarely been used by system architects in setting up computing systems. However, the role of socio-technical concepts in computing, which is becoming social in nature, has made the concepts more relevant and commercial. Tax information systems are examples of such systems because they are influenced by external variables such as the political environment, technological trends, and social environment, introducing complexity in their deployment and determining the type of e-services and their delivery to a diverse group of people. It was observed that in Tanzania there is resistance, reluctance and minimal use of electronic tax system because …

Fully Coupled Internal Radiative Heat Transfer For The 3d Material Response Of Heat Shield, Raghava S. C. Davuluri, Rui Fu, Kaveh A. Tagavi, Alexandre Martin

Mechanical Engineering Faculty Publications

The radiative transfer equation (RTE) is strongly coupled to the material response code KATS. A P-1 approximation model of RTE is used to account for radiation heat transfer within the material. First, the verification of the RTE model is performed by comparing the numerical and analytical solutions. Next, the coupling scheme is validated by comparing the temperature profiles of pure conduction and conduction coupled with radiative emission. The validation study is conducted on Marschall et al. cases (radiant heating, arc-jet heating, and space shuttle entry), 3D Block, 2D IsoQ sample, and Stardust Return Capsule. The validation results agree well for …

Novel And Fast Peridynamic Models For Material Degradation And Failure, Siavash Jafarzadeh

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Fracture is one of the main mechanisms of structural failure. Corroded surfaces with chemically-induced damage are, notably, potential sites for crack initiation and propagation in metals, which can lead to catastrophic failure of structures. Despite some progress in simulating fracture and damage using classical models, realistic prediction of complex damage progression and failure has been out of reach for many decades. Peridynamics (PD), a nonlocal theory introduced in 2000, opened up new avenues in modeling material degradation and failure. Existing numerical methods used to discretize PD equations, however, are quite expensive as the PD nonlocal interactions make them unaffordable for …