Operations Research, Systems Engineering and Industrial Engineering Commons^™

Color Removal From Pulp Mill Effluent Using Coal Ash Produced From Georgia Power Coal Combustion Plants, Christopher B. Willett

College of Graduate Studies: Theses & Dissertations

Two environmental concerns currently face Georgia: coal fly ash (CFA) waste from coal power plants, and the effluent generated by pulp mills. Pulp mill effluent discolors surface waters into which it is discharged, and has been proven to negatively impact the dissolved oxygen and carbon necessary for aquatic life. The proposed solution is a cost-effective adsorption treatment using an inexpensive but abundantly available waste material: CFA. CFA possesses beneficial properties that allow it to effectively remove contaminants, and is available at significantly reduced cost. The primary research objective was to define treatment parameters that would result in the maximum removal …

Size Effects In Human Visual Inspection For Micro/Meso Scale Parts, Sri Harsha Kavuri

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Visual inspection has been a major method of quality control in conventional manufacturing processes for the last fifty years. Utilizing trained human inspectors to perform this visual inspection has been the most effective means of maintaining quality control. Extensive research has been performed to understand the factors that influence the human inspection process.

In the recent years, there has been a significant emphasis on manufacturing at the smaller end of the size-spectrum such as Micro and Meso scale manufacturing. Quality control at becomes a challenging task due to the extremely small sizes. Several automated visual inspection techniques have been proposed …

Process Improvements Of Cilantro Harvesting With Ergonomic Considerations, Eric Penningroth, Branden Shimamoto

Industrial and Manufacturing Engineering

The problems presented by Talley Farms to the team were a lower than desired cilantro harvesting capacity and work health pertaining to lower back problems. The project objectives were to address and improve upon both of these objectives. To increase harvesting capacity, a simulation model was created using standard times from time studies. The simulation model helped to compare the different harvesting methods as well as the effect of the utilization of the on-site manager. The throughputs between each of the models were analyzed. To address ergonomic concerns, a work sampling study was conducted and it was determined that kneeling …

Bikeshare Business Model For Cal Poly- San Luis Obispo, Justin Benson, Andrew Neil Gatchalian

Industrial and Manufacturing Engineering

With the increasing admittance of students into colleges and universities across the nation, the need for alternate modes of transportation is becoming more pressing. College and university campuses, as well as small cities, in which there is a college or university, are being overloaded with student cars. In San Luis Obispo specifically, parking on campus as well as downtown can be extremely difficult to find. Traffic is also getting progressively worse, especially at the hour when class begins/ends and student arrive to or leave campus. Financial reasons are yet another deterrent for students at Cal Poly. Parking permits, gas, and …

Effects Of Patient Factors On Implantation Rates In In Vitro Fertilization, Heidi Richardson, Sofia Soto

Industrial and Manufacturing Engineering

The purpose of this report is to evaluate the effects of patient factors and embryo quality on the implantation rate in In Vitro Fertilization (IVF). For this report, statistical methods are used to test the significance of several patient and embryo characteristics on embryo implantation rate. This project is an analysis of data collected from over 36,000 patients.

The analysis concluded several findings. There was enough statistical evidence to conclude that age was significant in regards to implantation rate and FSH levels. As the patient ages, the amount of FSH levels found in their blood increases. A patient with high …

Redesign Of Talley Farm's "Fresh Harvest" Produce Program, Nicole Bordwell, John Rivera, Jared Toboni

Industrial and Manufacturing Engineering

Fresh Harvest, a Central Coast Community Supported Agriculture (CSA) program run by Talley Farms located in Arroyo Grande, CA, has a rapidly growing customer base. They harvest, package, and deliver boxes of fresh quality produce to almost 3000 subscribers. However, Talley Farms’ space for production and processing is limited and at times required for other aspects of business. This results in a problem where Talley Farms current processing system of produce for the Fresh Harvest program is not suitable for the forecasted growing demand. This report addresses the need to prepare for continued significant growth to the demand for Fresh …

Analysis And Improvement Of The Security Building At Pg&E Diablo Canyon Nuclear Power Plant, Alyssa Carter, Natalie Christa, Phuong Anh Pham Dinh

Industrial and Manufacturing Engineering

A new Security building was recently designed and built at the Pacific Gas and Electric (PG&E) Diablo Canyon Power Plant (DCPP).This building’s staff and equipment are responsible for performing routine inspections on all personnel entering the facility in order to prevent security-related incidents from occurring at the nuclear power plant. Similar to airport security procedures, the DCPP security building routine inspections include the use of x-ray machines, metal detectors, and explosive detectors.

The Power Plant periodically experiences pre-planned, preventive maintenance outages, that last 4-6 weeks. During an outage, a power plant reactor is shut down for maintenance, repair, and re-fueling. …

Semi-Automated Glass Mat Splice Operation For Asphalt Shingle Line, Justin Bracci, Harry Zhao, Chad Linafelter

Mechanical Engineering

The following report details the senior project sponsored by GAF Materials Corporation, Shafter, CA in regards to semi-automating a glass-mat splicing table for asphalt roofing shingle production. Herein includes details, research, design, and analysis regarding the semi-automation of the gluing processes for the splicing table. A working prototype was manufactured and tested for the future implementation onto GAF’s production line or further senior project involvement.

A Control-Chart Based Method For Solder Joint Crack Detection, Jianbiao Pan

Industrial and Manufacturing Engineering

Many researchers have used different failure criteria in published solder joint reliability studies. Since the reported timeto-failure would be different if different failure criteria were used, it would be difficult to compare the reported reliability life of solder joints from one study to another. The purpose of this study is to evaluate the effect of failure criteria on the reported thermal fatigue life and determine which failure criterion could detect failure sooner. First, the application of the control-chart-based method in a thermal cycling reliability study is described. The reported time-to-failure data were then compared based on four different failure criteria: …

Creating A Seamless Pipeline Into Undergraduate Programs In Stem Fields Through Region-Wide Articulation Agreements, Immanuel Edinbarough, Mikhail M. Bouniaev, Bill W. Elliott

Manufacturing & Industrial Engineering Faculty Publications

Underrepresented minority students pursue science, technology, engineering, and mathematics (STEM) related degrees at much lower rates compared to other segments of the population. To attract minority students, schools with STEM programs have resorted to myriad strategies such as cohorts, scholarships, mentoring, summer bridges, etc. Some schools have also sought innovative ways to develop a pipeline for graduates of two-year technical degree programs to matriculate into their four-year STEM programs and complete the remaining coursework leading to a BAT or BS degree. The University of Texas at Brownsville (UTB) has adopted this latter innovative approach to increasing student enrollment in STEM …

2d Wireform Process Improvement, Katy Conlin, Carlo Ebora, Jordan Gamble

Mechanical Engineering

The body of this work has been created for Edwards Lifesciences in conjunction with senior project requirements. As such, the information produced and contained within is under a non‐disclosure agreement. As per request by sponsor, the body of the work will not be submitted to any outside parties, and the title page will serve as proof of completion.

A Control-Chart Based Method For Solder Joint Crack Detection - Conference Proceeding, Jianbiao Pan

Industrial and Manufacturing Engineering

Many researchers have used different failure criteria in the published solder joint reliability studies. Since the reported time-to-failure would be different if different failure criteria were used, it would be difficult to compare the reported reliability life of solder joints from one study to another. The purpose of this study is to evaluate the effect of failure criteria on the reported thermal fatigue life and find out which failure criterion can detect failure sooner. First, the application of the control-chart based method in a thermal cycling reliability study is described. The reported time-to-failure data were then compared based on four …

Design Of Transportation Process For Band Equipment, Marissa N. Blustein, Chris M. Kaye

Industrial and Manufacturing Engineering

The following report documents the attempt to design a safe and reliable process for transporting Louder Space’s musical gear that requires minimal physical demand. Design specifications were derived from customer requirements as well as human factors principles. The transportation process was broken down into systematic process steps and standardized, making use of lean methodologies in order to reduce the number of non-value steps involved. Furthermore, a model portable storage unit for miscellaneous gear was developed to the specifications determined by the band using 3D modeling, as well as certain limiting constraints. Once the customer approved the prototype, the product was …

Lean Fire Management: A Focused Analysis Of The Incident Command System Based On Toyota Production System Principles, Jeremiah S. Fugate

Theses and Dissertations--Mechanical and Aerospace Engineering

A primary role of the Incident Command System is to learn from past incidents, as illustrated by its origins in the wildland firefighting community. Successful emergency response operations under the Incident Command System has prompted its nationwide spread, this promulgation critically relies on the system’s capability to stabilize and continuously improve various aspects of emergency response through effective organizational learning. The objective of this study is to evaluate the potential to apply fundamental principles of the Toyota Production System (Lean manufacturing) to improve learning effectiveness within the Incident Command System. An in-depth review of literature and training documents regarding both …

S1nn Gmbh & Co. Kg (Automobile Connectivity Module 1.1), Tyler Alexander Ball

Industrial and Manufacturing Engineering

The results of this report show how when diagnostics were run on the Connectivity Module 1.1, the problems discovered such as potential short-circuiting, 90-degree copper tracing angles, and components overheating/tombstoning were addressed. By using the method of “DMAIC,” which stands for Design, Measure, Analyze, Implement, Control, successful corrections were made. In the first design of the Printed Circuit Board (PCB), 1454 critical issues were found. With the newly designed PCB’s modifications being implemented, only 12 critical issues remained, which were later addressed and corrected. The results from this report are a functional Automobile Connectivity Module 1.1.

Project Management Of High School Shadow And Building An Engineer Day, Andrea M. Carroll

Industrial and Manufacturing Engineering

Building an Engineer Day and High School Shadow are semi-annual outreach events hosted by Cal Poly’s Society of Women Engineers section during fall and spring quarters. The events focus on encouraging women and minorities to take an interest in engineering. These events are the two largest outreach events hosted by The Society of Women Engineers and need to run smoothly in order to provide student attendees with a meaningful experience.

Building an Engineer Day and High School Shadow are currently un-organized and un-planned, which leads to problems with officer retention, increase in expediting process and a low attendance rate at …

Equipment Maintenance And Replacement Decision Making Processes, Michael W. Gage

Industrial and Manufacturing Engineering

This project contains recommendations for the decision making processes for support and production equipment maintenance and replacement for a large defense contractor. Recent literature has been reviewed to provide perspective on current trends in the field. A complete evaluation of their current processes and systems is included with recommendations on areas for improvement. A decision support system is also proposed to supplement their existing decision making.

Fixture For Carbon Fiber Spar Of Human Powered Helicopter, David John Ikeda, Luis Gonzalez

Industrial and Manufacturing Engineering

The following report describes our contribution to Cal Poly Human Powered Helicopter for the 2012 competition for the Sikorsky Prize offered by the American Helicopter Society. In order to win this prize the team needs to build and fly a human powered helicopter for more than 60 seconds reaching and altitude of 3 meters while staying in a 10 meter square box. Our team was created to support the integration of Carbon Fiber parts, specifically the carbon fiber spars with rotor and landing gears. Precise cutting and accurate drilling was needed and our team was tasked with creating a fixture …

Theory Of Constraints Project Management In A Manufacturing Environment, Shihching Kraft

Mechanical & Aerospace Engineering Theses & Dissertations

The following thesis covers the concepts of Theory of Constraints (TOC) Project Management. Introduced by Eliyahu M. Goldratt in I 984, TOC is a management philosophy that focuses on the use of critical chain project management to prioritize everyday tasks in a company. In TOC Project Management, there is always at least one resource constraint that limits the speed at which projects are completed. TOC management philosophy also recognizes that most projects in the manufacturing industry face unknown schedule delays that could cause projects to be completed late or over the planned budget. During project plan creation, plans are developed …

Low Volume Dispensing With High Speed Dispensers, Sunny Agarwal

Graduate Dissertations and Theses

With the high pace of innovation in the semiconductor manufacturing industry, there has been an increasing demand for more energy efficient and environmental friendly products. This research relates to a complex process of fluid dispensing at low volumes on a printed circuit board. Currently, a more refined non-contact dispensing terminology named “Streaming” is widely used to stream out material at low volumes for various applications. The key solution is to frame a dispensing method that lends itself most closely to the requirements of a specific production process.

This study represents a detailed approach of dispensing low volumes of materials in …

Project Based Learning In Engineering Economics: Teaching Advanced Topics Using A Stock Price Prediction Model, Lizabeth Schlemer

Industrial and Manufacturing Engineering

A graduate level advanced engineering economics class taught at California Polytechnic State University, San Luis Obispo, includes a thorough review of time value of money, investment evaluation, inflation, risk and return, financing decisions, corporate investment strategies, risk analysis and decisions incorporating non-monetary considerations. Historically this course was taught using an advanced text where the topics were covered sequentially. A redesign of the course now includes the construction of a stock price prediction model for a company of the student’s choice. Through the model, the topics are covered and discussed in the context of the large model-building project. For instance, inflation …

Exploring A High-Tech Approach To Subterranean Dwelling Environments For Commercial Implementation, Matthew Richard Gordon

Industrial and Manufacturing Engineering

People are always looking to experience something interesting and unique when on vacation. What could be more unique than staying in a hotel that is completely underground? While people have always been amazed at natural caves and other subterranean structures, the idea of spending the night in one of these is a somewhat untried area, although it could be quite the selling point. This being the case, the idea of a subterranean hotel is not so farfetched, however there are a number of issues that arise with this project. These issues include construction and selecting the proper site and building …

Cal Poly Chocolates, Jason Ferrel, Taylor Fitzpatrick

Industrial and Manufacturing Engineering

Our design for this project began with building a strong understanding of the current production process. A meeting with the manager, Anna Nakayama, provided a detailed overview of the entire process and outlined some areas of concern. In addition, she provided us with access to critical data such as standard operating procedures and inventory spreadsheets. From there, time studies were conducted for each of the 8 types of chocolate. These time studies helped identify three main issues facing Cal Poly Chocolates. The first issue is in the packaging area of production. The process is entirely manual and has become a …

Qualification Of A New Glass Bottle With E&J Gallo Winery, Danielle Leanne Medeiros

Industrial and Manufacturing Engineering

This paper will further examine the procedures involved in transitioning to a new bottle type made by Glass Company B, on a specific bottling line within E&J Gallo’s bottling facility. For this project Bottling Line X will require thorough testing as well as the creation of a changeover choreography plan. The testing procedure will follow a 3 phase process utilizing project management and statistical skills to ensure quality standards are upheld with the transition. Since Bottling Line X is not familiar with transitioning between bottle types, lean manufacturing techniques will be required to create a changeover document ensuring operators are …

Application Of Data Envelopment Analysis To Identify Undervalued Equities On The Dow Jones Industrial Average, Ryan L. Kotzebue

Industrial and Manufacturing Engineering

Two factors that drive investors to and away from the stock market are reward and risk, respectively. By using a stock selection strategy that is quantitative, investors may feel more comfortable and secure with their decisions. However, there lacks a quantitative strategy that can produce increased returns with lower risk by purchasing a small number of stocks. The objective of this project was to formulate a quantitative stock trading strategy that produced exceptional returns with low risk while also fulfilling additional requirements to benefit the common investor.

By using a linear programming based operations research technique known as data envelopment …

Facility Redesign At The Systech Corporation, Jacob J. Rucker

Industrial and Manufacturing Engineering

This senior project is a redesign of Systech’s manufacturing floor as they move to their new facility to be able to support the expected increase in customer demand. As of January 2013, Systech was working near full capacity, and because of their new product release, they expect the demand to outstrip the production capabilities of the current facility. Because of this, Systech is moving their final testing operations in San Diego to a larger building. During this transition, they have expressed interest in redesigning the current floor layout in order to maximize the productivity of their employees. To accomplish this, …

Wart Eliminator Project Report, Colton Story, Kyle Shipman

Industrial and Manufacturing Engineering

The Wart Eliminator is a product based on the theory of resonant frequency and its ability to devitalize pathogens with the use of electronic pulses. Using the resonant frequency of the wart’s pathogen, the device is operated by the user with two switches for power and a probe connected by a wire to the device for applying to the affected area of the user while running three minute cycles. The product is in the beginning stages with only a prototype made. The product needed a proper ergonomic design to be easily used by the user and a cost analysis to …

Simulating The Flow Of Students Through Cal Poly's Undergraduate Industrial Engineering Program For Policy Analysis, Alexander Clayton Weber

Industrial and Manufacturing Engineering

The purpose of this project is to analyze the flow of Industrial Engineering students at California Polytechnic University San Luis Obispo in order to measure various graduation metrics by use of a simulation. Currently, graduation rates are relatively low in comparison with the rest of the state of California and future growth and decreased budgets may threaten graduation rates for incoming students. This simulation will identify bottleneck classes [those that hold up students from graduating] and provide a basis for a sensitivity analysis in which different scenarios are constructed to determine their effects on graduation metrics. The simulation will offer …

Lunalight - Bringing Light To The Expanding World, Gabriela M. Igel, Daniel J. Patrick, Kimberley M. Smith

Materials Engineering

The LunaLight, a solar rechargeable light and cell phone charger, addresses the lack of access to electricity faced by 1.4 billion of the world’s population (International Finance Corporation). The LunaTech team has developed a product that is bright, simple, compact, versatile and competitive with existing products. Through a partnership with the non-profit organization One Million Lights, LunaTech has improved a previous team’s design to address user feedback, concerns of durability, and manufacturability.

The LunaLight design includes a 5 component plastic housing held together by 4 screws, a surface mounted PCB, a lithium-ion (Li-Ion) battery, one high-brightness LED, a solar panel, …

Application Of Systems Engineering And Project Management For Algae Photo Bioreactors, Andrew S. Balberchak

Industrial and Manufacturing Engineering

EXECUTIVE SUMMARY

Today there is much talk about different sources for biofuel to replace the decreasing supply of fossil fuels. Algae seem very promising with its abundance across the globe and relatively simple growing conditions. Lipids can be extracted from this organism which is then converted to biofuel. Although biofuel production from algae is not economically viable at this stage, researchers are suggesting using the by-products of algae for supplemental and healthcare use. If true, this could justify the economics of obtaining fuel from algae by creating more markets from various algae products.

Cal Poly State University’s Food Science and …