Increasing The Independence Of Children With Spina Bifida Through The Designing And Building Of A Mechanical Aide, Andrew Duffek, Robert Brent, Michael Hamada, Melissa Rodriguez

Industrial and Manufacturing Engineering

In order to assist Silas Hopper, a child with spina bifida, with getting into his wheelchair independently when being on the ground, the senior project team set out to construct a device that would fulfill that purpose. They did this through coming up with a strict definition of the problem to be solved, designing a number of potential solutions for the problem, prototyping to determine the feasibility of the solutions, making design modifications after testing the prototype, and building the final device.

The end product was a device that was able to operate mechanically, with a design that considered safety …

Small Scale Erp Engine Design, Colyn Muir Dickson, Matthew Wade Haymond

Industrial and Manufacturing Engineering

This project set out to create a 1) low-cost, 2) dynamic, and 3) user-friendly small scale ERP software tool. These three key attributes position this product against complex and expensive systems such as SAP or Oracle. While the product still retains the dynamic and financial capabilities any good ERP system should have, the biggest value proposition is its simple and user-friendly interface. The software has a dual product-market fit: for small businesses as a low-cost planning tool, and for universities as a teaching tool. In the design phase, the team kept a primary focus on ergonomic software development while maintaining …

Tesla Motors Quality Engineering Application And Implementation, Nick Kwan

Industrial and Manufacturing Engineering

Tesla Motors, in Winter 2013 during the author’s coop,had a variety of potential improvement areas regarding their quality engineering team. There were too many overall defects on the vehicles. Those defects were recognized as the cars were passing through inspection, coming off the line, as well as brought by customers to after-purchase service. One of the defects was the Charge-port Door Malfunction, in which the door of the Model S would not open on command. An additional defect was the Windshield Wiper Malfunction, in which the fluid was not hitting the car at the desired angle. Both of these defects …

Database Design For The Collection And Visualization Of Sustainabilty Data, Henry A. Kozlowski, Nikhila Perugupalli

Industrial and Manufacturing Engineering

The goal of the project was to create a database that would be a repository for the high volume of sustainability data Illumina would like to collect. To couple with the database the project team’s goal was to design a system for visualizing the data graphically. Illumina required a database system that would be user-friendly, easy to add, delete, and edit data inputs, as well as a program that would allow the user to easily sort and graph data. The intent of the graphical representation of the data is to publish the graphs in a monthly report that would be …

Industrial Engineering Consulting, Blake J. Ahrold, Torrey M. Plana

Industrial and Manufacturing Engineering

This paper documents the senior project of Blake Ahrold and Torrey Plana. This project was created to provide a solution to the problem of small to medium Sized enterprises (SMEs) being under represented by lean consulting companies. The project was at first intended to be a lean consulting startup and then pivoted to The Systems Optimization Club. A project charter, Gantt chart, and business model canvas were created for the startup and used as guidelines in the creation of the Systems Optimization club. The club is to be run like a lean consulting company. The club will provide teams of …

Strasbaugh Nonconforming Report Optimization, Eden Andersen, Angela Asgekar, Rebecca Gregg

Industrial and Manufacturing Engineering

This paper strives to convey the problems and proposed solutions for Strasbaugh’s Nonconforming Report (NCR) Optimization. Strasbaugh is a world leader in silicon wafer polisher and grinder technologies. After a significant down size to the company parts they used to manufacture now have to be purchased, and many of these incoming parts do not conform to Strasbaugh’s high standards. This has led to an increase in NCRs that need to be processed, which takes up time, resources and money.

The objective therefore became to update the multi-sheet carbon copy paper system to better optimize the use of these reports and …

Designing A Supply Chain For Wine Imports, Italy To California, Neil Magnuson, Sam Bucher

Industrial and Manufacturing Engineering

Executive Summary

In this report a framework for a hypothetical business will be covered. Bucher & Magnuson Wine Import Inc. has provided a business plan as well as a detailed supply chain design for operations. In addition, a model for scaling and a redesign of a possible storage facility will be found. This comprehensive document outlines end to end the supply chain model of the hypothetical business and moreover a framework for starting a wine import business in San Luis Obispo.

The conclusions of the results from this model are the following:

• Unconcerned with time, the cheapest route for 1 …

  ---

  Go to article

An Automated Solution For Analyzing Supply Chain Performance, Paul Ringelstein

Industrial and Manufacturing Engineering

The world is becoming increasingly connected as technology progresses and globalization reaches more countries. This interconnection creates new challenges and new relationships for both people and businesses. Now, more than ever, businesses have to work together to satisfy the high demands of customers.In a world full of complex organizations that do business together, the supply chain has become the heartbeat of corporations. The interconnectedness of the organizations in the supply chain is critical to the success of all components of the supply chain. In order to gain an advantage in markets today, data needs to be used to determine where …

Analysis Of 3d Printer Schedule, Colin B. Mclane

Industrial and Manufacturing Engineering

With recent innovations in technology, 3D printing has become a rapidly expanding manufacturing method that is being used for a wide range of applications. Their ability to build parts layer by layer instead of cutting away initial material allows this method to have almost no wasted material, creating the potential for a much more efficient, cost effective process. In order to continue the growth of this manufacturing strategy, the performance of 3D printers need to be enhanced to ensure equal or higher quality of produced parts in comparison to other manufacturing methods that are more commonly used. One important part …

Cost Effective Analysis Of Big Data, Steven J. Litzsinger, Nehad Dababo

Industrial and Manufacturing Engineering

Executive Summary

Big data is everywhere and businesses that can access and analyze it have a huge advantage over those who can’t. One option for leveraging big data to make more informed decisions is to hire a big data consulting company to take over the entire project. This method requires the least effort, but is also the least cost effective. The problem is that the know-how for starting a big data project is not commonly known and the consulting alternative is not very cost effective. This creates the need for a cost effective approach that businesses can use to start …

Design Of An Automated Vehicle Detection System For Bicycles: Fireworks Cycling Sensor, Jason Cheng, Peter Kim, Tory Morgan, Clayton Young

Industrial and Manufacturing Engineering

Abstract

This report explores the necessity for increased cyclist safety in urban settings, leading to the birth of a product which aims to drastically reduce the risk of accidents while heightening the sense of safety overall. The project outlines and details the product development process of a consumer-friendly vehicle detection system, with a holistic scope which includes technical rapid prototyping and coding, team dynamics, decision making process, and change management. Two formal prototypes were developed before a functional final product was identified and constructed, each iteration drastically improving practicality and efficiency of detection. The final product underwent extensive testing in …

Economic Analysis And Justification For Automated Welding Systems, Roxanne Raye

Industrial and Manufacturing Engineering

This report looks at designing a new welding process for a company in the Oil & Gas industry, ensuring method consistency and performance quality of their steel drill bit while increasing overall production. The current product is welded manually with a flux core wire, resulting in high cycle times and numerous cases of required rework.

The use of automation systems will be analyzed for their increased consistency, quality, safety, and production estimates. Specifically robotic cell design will be considered, since it can work on more parts with fewer operators, adding efficiency and flexibility to the production floor. Other areas of …

Dcpp/Polygait Inventory Control System, Logan Pace, Robert Garlinghouse

Industrial and Manufacturing Engineering

This report discusses a proposed system to improve upon inventory management issues experienced in the M&TE Tool room for the PG&E Diablo Canyon Power plant. Effective inventory tracking and management is an important characteristic of any organization handling physical assets, and without the proper system in place, companies may lose expensive items and waste time by not having equipment available when needed. The tool room is experiencing inventory shrinkage of M&TE equipment nearing $100,000 per year largely because of an inefficient checkout system that fails to keep employees accountable for the tools they check out. Even more costly than the …

Quality Improvement At Patio Pacific, Petdoors, Tri Minh Nguyen, In Woo Suh

Industrial and Manufacturing Engineering

Quality is key in manufacturing any type of product. Customer expectations only rise with time, and it has become more crucial than ever for companies to produce quality products to survive. This project sets out to improve quality of flagship products at Patio Pacific. This report contains the background of the company, Patio Pacific, the process of finding critical problems, and the methodology to solve them.

Customer returns and inquiries have the ability to eat up cash flow in any type of company. This senior project sets out with introduction of the project that explains how the project came about, …

Cal Poly Dining: The Avenue Redesign, Eric Calbonero, Derek Nollsch, Casey Reilly

Industrial and Manufacturing Engineering

Executive Summary

Campus Dining is planning to close VG’s Cafe during the 2015-2016 school year; as a result, the remaining restaurants on campus need to accommodate the additional student demand. The student team consisting of Eric Calbonero, Derek Nollsch, and Casey Reilly met with Campus Dining’s Director of Operations, Greg Yeo, about this issue—he directed the team toward a redesign of The Avenue Food Court. To redesign The Avenue, the project team focused on several key deliverables as follows:

• Study current customer trends in The Avenue

• Develop a proposed facilities layout and design

• Perform a capacity analysis of The Avenue …

  ---

  Go to article

San Luis Obispo Children's Museum: The Circuit Lab, Megan Garcia, Victoria Higgins, Michael Xie

Industrial and Manufacturing Engineering

Executive Summary

Over a nine month period, the senior project team worked closely with the San Luis Obispo Children’s Museum to develop a new interactive exhibit for the museum’s Science, Technology, Engineering, and Mathematics (STEM) floor. The initial budget given for this project was $3,000. The museum’s requirements for a new exhibit were that it must be safe for young children to use, require minimal supervision, is interactive, has learning objectives, and is economically feasible and sustainable. The team chose to build an exhibit that would teach young children about simple circuitry and electronics.

First, extensive research of circuits, children’s …

Warpage And Shape Distortion In Laser Metal Sintering, Xuan Wang

Industrial and Manufacturing Engineering

Selective Laser Sintering (SLS) is the primary method to fabricate metal and ceramic components in additive manufacturing. Due to the anisotropy of powder material, the sintering rate difference will inevitably causes shape change, distortion , and other defects of sintered parts. In this paper, a continuum model was developed to simulate the SLS process. The developed model has been successful to predict sintering kinetics. The impact of processing parameters, such as laser power, scanning speed, hatching distance, and particle size has been studied . The proposed method provides an innovative tool to optimize SLS process parameters.

Improving Connectivity Between Members And Alumni Of Alpha Pi Mu, Ben Patrick Buell, Shannon Elizabeth O'Keefe

Industrial and Manufacturing Engineering

The purpose of this project was to solve the problems of a lack of connectivity between the current members and alumni of Alpha Pi Mu, as well as the lack of incentives for prospective members to join the club. These problems were solved by creating a website that allowed current members to be able to view the complete work experiences of alumni and provided a way to reach out to those alumni directly to network with them. The agile project management system was used to develop the website and helped to successfully complete all of our design requirements listed in …

A Case Study Of Multiple-Use Finish Electrodes For Die-Sinking Edm, Troy A. Robertson

Masters Theses & Specialist Projects

This study examines the use of one finishing electrode to finish multiple dies without remachining the electrode. The multiple-use electrode finishing experiment in this study addresses technology in the die-forging industry. Methods of manufacturing spherical straight bevel forge gear dies have relied on die-sinking Electrical Discharge Machining (EDM) practices that showed great potential for advancement. The focus of this study is solely on the improvements of electrode use in EDM finishing-processes. The surface finish quality itself is not an area of concern other than maintaining that it does not diminish. The focused concern is maximizing the process by using one …

Loss On Ignition Using Infrared Heating, Benjamin J. Binoniemi

Masters Theses

The focus of this study is a proof of concept that infrared heating can be used to produce a reliable and rapid method of performing the loss on ignition test. The loss on ignition test is a foundry industry standard test that requires all moisture and volatile organic compounds be vaporized from a sample of foundry sand. The standard test as recommended by the American Foundry Society uses a muffle oven and requires nearly four hours to perform. This new concept performs the same test in approximately ten minutes. The biggest issues with the loss on ignition test are time …

Creating A User-Friendly Personal Wine Collection Inventory Management System, Peter Loddengaard

Industrial and Manufacturing Engineering

This project set out to create a user-friendly wine collection management software. Existing systems were reviewed and discussions with collectors took place to establish the user requirements for this type of inventory management system. This led to the scope of the project being narrowed to making a wine bottle entry form that was quick and easy to use. The programming language, Ruby on Rails, was used to design this system, and learning the software was a large part of the project itself. It was established that four forms would be designed using combinations of two ergonomic factors: an “F” shaped …

Wasco Environmental Chamber System Manifold, Steve Mark Yatco

Industrial and Manufacturing Engineering

This report details the process of designing and producing a manifold that connects ultra-high purity (UHP) pressure and vacuum switches to an air supply so that the parts may be tested in an environmental chamber. Using the DMAIC (define, measure, analyze, improve, and control) methodology of problem solving, progress on the project includes thorough research about the problem, preliminary design solutions, iterative prototyping, and testing specific functionalities. Manufacturing engineering topics of tooling, fixturing, metrology, quality, and machining with manual and computer numerical control (CNC) varieties of both mills and lathes are applied during the course of the project. The report …

Frito-Lay - Supply Chain Impact Analysis, Kerri Blosch, Vincent Phua, Jeffrey Silva

Industrial and Manufacturing Engineering

The snack food company Frito-Lay relies on Route Sales Representatives (RSRs) to stock and maintain shelves of snack foods in every store. Frito-Lay currently does not have a system which can accurately predict cannibalization, or the effects of a store opening or closing on other stores of the same chain in the area. The goal is to sort through 1900 stores in a given metropolitan area to see the effects of cannibalization. In order to tackle the problem, a Microsoft Access program was created to filter stores based on location or whether the store was open for the full three-year …

Process Testing And Improvement Of Tapping Machinery At Lisi Aerospace, Michael James Hester

Industrial and Manufacturing Engineering

This report documents my senior project for California Polytechnic State University San Luis Obispo. I have chosen to do a senior project with Lisi Aerospace. Lisi would like to compare the manufacturer rated cycle count of taps versus an experimental one based on our machines in house. My goal for this project would be to run an experiment on one tapping machine and report on the achievable cycle count for the taps. I plan to do this in several ways including:

• Running extra cycle counts above tap manufacturer recommendations

• Documenting machine failure modes

• Create a process document to be repeated …

  ---

  Go to article

Improving Advertisement Recognition And User Interface Of Gameofwarrealtips.Com, Chad Kihm, Alexander Meyer

Industrial and Manufacturing Engineering

The purpose of this experiment was to determine which location of advertisement would be the most recognized on the Game of War Real Tips website and to improve the website’s user interface by using both quantitative and qualitative data. To accomplish this, two experiments were created. The first experiment was designed to determine which location of advertisement would be recognized most by users. A screen would flash for 0.5 seconds and the subjects would mark where they believed they recognized an advertisement. A statistical analysis was completed to determine whether the location of the advertisement had an effect on the …

Wine Club Shipment Package Redesign, Emily E. Prescott

Industrial and Manufacturing Engineering

This report shows the design, manufacturing, and testing process for the product development of a wine club shipment package for Niner Wine Estates. Niner has two different shipment sizes, 4 bottles and 6 bottles, and wishes to improve their current package by giving it a more “high-class” feel. After the new package was designed and prototyped, it went through standardized quality testing to be cleared for commercial use. This testing is intended to simulate the distribution cycle the package will experience and subject it to potential hazards such as being dropped and vehicle vibration during transportation.

After the package passed …

A Framework For Sustainable Material Selection For Multi-Generational Components, Ryan T. Bradley

Theses and Dissertations--Mechanical and Aerospace Engineering

The early stages of a product’s design are a critical time for decisions that impact the entire life-cycle cost. Product designers have mastered the first generation; however, they currently do not have the ability to know the impact of their decisions on the multi-generational view. This thesis aims at closing the gap between total life-cycle information and the traditional design process in order to harbor sustainable value creation among all stakeholders involved. A framework is presented that uses a combination of a life-cycle costing methodology and an evolutionary algorithm in order to achieve a sustainability assessment for a true multi-generational …

A Simulation-Based Approach To Risk Assessment And Mitigation In Supply Chain Networks, Mamadou Seck, Ghaith Rabadi, Christian Koestler

Engineering Management & Systems Engineering Faculty Publications

We present in this paper a simulation-based approach to evaluate the risk associated with supply chain disruptions caused by failures in some supply chains nodes and measure the impact of such disruptions on supply chain key performance measures (KPIs) of interest. The proposed framework enables analysts and managers to repeatedly assess the risk to their supply chains based on various simulated scenarios and identify the most critical nodes whose disruption will have the highest impact on the KPIs of interest. As a result, companies can focus on the most critical supply chain assets and develop targeted mitigation plans that minimize …

Engineered Surface Properties Of Porous Tungsten From Cryogenic Machining, Julius M. Schoop

Theses and Dissertations--Chemical and Materials Engineering

Porous tungsten is used to manufacture dispenser cathodes due to it refractory properties. Surface porosity is critical to functional performance of dispenser cathodes because it allows for an impregnated ceramic compound to migrate to the emitting surface, lowering its work function. Likewise, surface roughness is important because it is necessary to ensure uniform wetting of the molten impregnate during high temperature service. Current industry practice to achieve surface roughness and surface porosity requirements involves the use of a plastic infiltrant during machining. After machining, the infiltrant is baked and the cathode pellet is impregnated. In this context, cryogenic machining is …

Machining Strategies Exploring Reduction In Energy Consumption, Abdullah Al Mamun

All Graduate Theses, Dissertations, and Other Capstone Projects

The main aim of this thesis is to explore machining strategies, analyzing energy consumption using Design of Experiments (DOE) at the material removal rate (MRR), compare to cutting geometrical trajectories according to CNC parameters such as spindle RPM, feed rate, depth of cut per pass and total depth of cut. Spindle RPM, depth of cut per pass, and feed rate are selected as the main three factors and each factor has two levels: low-level (-) and high-level (+). These experiments have been performed at an end-milling machine by using a concept of a constant volume of material removal processes in …