Operations Research, Systems Engineering and Industrial Engineering Commons^™

Studying The Technology For Obtaining Zinc Chloride From Spent Supporter Waste In Ammonia Production, A.T. Dadaxo‘Jaev, Sodikjon Kadirov

Chemical Technology, Control and Management

This article presents the results of research on the recycling of spent zinc adsorbents formed during the ammonia production process, aimed at obtaining zinc chloride (ZnCl₂), which can be utilized in various industrial sectors, including electroplating. The research covers the optimization of technological parameters such as hydrochloric acid concentration, temperature, and reaction time to efficiently extract zinc chloride. The experiments revealed that the best results are achieved by using a 20% hydrochloric acid solution, at a temperature of 60°C, with a reaction time of 60 minutes. The resulting 40% zinc chloride solution was tested in electroplating production, where it met …

Research Of The Dynamic Characteristics Of A Time-Pulse Ultrasonic Sensor, Aliev Ravshan, A.U. Djalilov

Chemical Technology, Control and Management

This article investigates the dynamic characteristics of a time-pulsed ultrasonic sensor used to measure water flow in open channels. The operating principle of the sensor, its response time in various hydrodynamic conditions, speed, and factors affecting measurement accuracy are analyzed. In the process of research, the improved ultrasonic sensor was tested and its effectiveness in measuring water flow in real time was evaluated. The results obtained showed that the sensor adapts to the velocity, temperature and turbulence level of the water flow. Based on the results of the research, the possibilities of working of time-impulse ultrasound sensors in open channels …

Application Of Quantum Algorithms In Optimization Of Cognitive Decision-Making Systems, Noilakhon Yakubova

Chemical Technology, Control and Management

The article analyzes the potential of quantum algorithms for optimizing cognitive decision-making systems in production processes in the energy sector. Compared with traditional algorithms, quantum algorithms allow high-speed processing of large amounts of variable data in real time and solving multiparameter problems based on an integrated approach. The study considers uncertainties and issues of increasing efficiency in the processes of production and distribution of electricity using a cognitive model. The integration of quantum algorithms into this model allows developing optimal strategies for using resources in production. A heating boiler was taken as a control object, and taking into account its …

Algorithms For Fast Fire Risk Prediction And Real-Time Data Processing, Mirzoyan Mirzaaxmedovich Kamilov, Tolaniddin Ramziddinovich Nurmukhamedov, Oybek Zokirovich Koraboshev, Bakhodir Saydullayevich Achilov

Chemical Technology, Control and Management

Ensuring fire safety in facilities with high fire risk is one of the pressing problems of modern society. Nowadays, there is a great need for accurate and effective prediction systems for fire prevention and rapid response. Since traditional methods do not provide the ability to quickly analyze and predict in real time, the development of algorithms and modern approaches using modern technologies is of great importance. This article analyzes fire risk prediction algorithms, their principles of operation and effectiveness, and considers methods for assessing and predicting fire risk using Artificial Intelligence (AI), Machine Learning (ML), and Big Data technologies. The …

Influence Of Substrate Temperature On The Properties Of Reactive Dc Magnetron Co-Sputtered Ag-Doped Tio2 Thin Films, Hezekiah B. Sawa

Tanzania Journal of Engineering and Technology (TJET)

This study reports on the influence of substrate temperature on the properties of Ag-doped TiO2 thin films. The films were deposited by reactive DC co-sputtering of Ti and Ag targets at different substrate temperatures and Ag target sputtering powers. Grazing incident X-ray diffractometer confirmed that all films were polycrystalline with dominant peak oriented along (101) planes representing the anatase TiO2 phase. The average grain size of the samples improved with increase in deposition temperature. At a substrate temperature of 450 ℃, the samples had a dominant peak representing the rutile phase, suggesting partial transformation from anatase to rutile phase. The …

Cellulose Recovery From Waste Denim Fabrics Through Indigo Vat Dye Reduction And Spandex Dissolution, Tito N. Venance

Tanzania Journal of Engineering and Technology (TJET)

This study addresses environmental conservation by tackling end-of-life management for post-consumer denim garments through the recycling of cotton fibres from waste denim. The purification process involved dithionite reduction of vat dyes in the presence of an alkali followed by selective dissolution of spandex using N,N-dimethylformamide (DMF). Optimal conditions for dye removal were determined at 90°C for 120 minutes with sodium hydroxide at 25 g/L, sodium dithionite at 6 g/L and PVP at 4.5 g/L, while spandex extraction was achieved using a 5% DMF solution at 70°C for 4 hours. Ultraviolet (UV)-vis spectrophotometric analysis indicated a significant increase in whiteness (DL*). …

Assessment Of Factors Contributing On Early Rotting Of Chromated Copper Arsenate Treated Utility Power Distribution Wood Poles In Tanzania, Innocent J. Macha

Tanzania Journal of Engineering and Technology (TJET)

The study aimed to assess the factors contributing to the premature decay of Chromated Copper Arsenate (CCA) treated utility power distribution wooden poles in Tanzania. Deteriorated poles samples from various regions in Tanzania were analyzed using handheld X-ray spectrometry to quantify the retention of CCA preservative chemicals. The ages of these poles were estimated based on annual growth rings. The findings indicated that premature failure of CCA treated wooden poles is attributed to an imbalance in the chemical composition of the preservative solution. The study found that CuO retention in most samples ranged between 10-18 kg/m3, significant lower that the …

Production Of Potassium-Rich Biofertilizer From Composted Banana Peels And Watermelon Rinds, Neema O. Msuya

Tanzania Journal of Engineering and Technology (TJET)

This study investigated the production of biofertilizer from composted banana peels and watermelon rinds, focusing on the mineral content and its impact on plant growth. The process involved characterizing raw materials, producing biofertilizer, analyzing mineral concentrations (potassium, nitrogen and phosphorus), and evaluating its quality through Spiny Amaranth seed growth. A compost bin with three compartments was designed, testing three composting ratios of banana peels to watermelon rinds (2:1, 1:2 and 1:1). Composting was monitored on moisture content, pH, organic matter, and temperature for 37 days. The 1:1 ratio had the lowest temperature (33.45°C) and highest pH (7.08), while the 2:1 …

A Fuzzy Based Framework For Sustainable Technology Selection In Small-Scale Gold Mining Operations, John M. Kafuku

Tanzania Journal of Engineering and Technology (TJET)

Small-scale gold mining (SSGM) operations in Tanzania has been operating inefficiently due to inadequate mining processing technologies, poor working tools, lack of enough capital, and insufficient electricity. Despite the efforts made by different stakeholders in boosting the sustainability of SSGM yet the sector has not reached the expected goal. This paper proposes a framework for appropriate technology selection to help small scale gold miners in evaluating various gold mineral processing technologies. The framework utilizes the fuzzy logic set theory for technology evaluation and selection. The developed framework for technology selection upon validation provided results that technology adequacy of more than …

Methodology Of Automated Control Of Situations In Structurally Complex Systems With Recycled Flows, Khusan Zokirovich Igamberdiev Academician, Madina Mirxalilovma Fozilova

Chemical Technology, Control and Management

This article discusses the methodology of automated management of situations in structurally complex systems with recycled flows. The need to develop a correct model for effectively controlling such systems based on scientific principles of analysis and decision-making is substantiated. Particular attention is paid to modeling, optimizing, and using digital technologies, including artificial intelligence, to improve the accuracy and efficiency of management decisions. The principles of decomposition, multi-criteria optimization, and linguistic models of fuzzy correspondence are described, which can be used in conditions of uncertainty and complexity of industrial facilities.

Joint Estimation Of The State And Parameters Of Dynamic Control Objects Based On The Maine Estimator, Yulduz Abdurakhmanova

Chemical Technology, Control and Management

The issues of constructing an adaptive joint estimation of the state and parameters of dynamic control objects using the Maine estimator are considered. There are various variants of the extended filter, and a variant based on iterations between parameter and state estimates was used in the work. In this version of the extended Kalman filter, the problem of joint parameter and state estimation is solved in such a way that parameter estimation is performed before state estimation. Then, the parameter values are used to assess the state. In this case, further iterations between the state vector estimation and the parameter …

Determination Of Chemical And X-Ray Phase Analysis Of Carbon-Containing Material, Sh.T. Juraev, B.F. Muxiddinov, U.T. Tailakov

Chemical Technology, Control and Management

This paper presents a chemical and X-ray diffraction study of the solid fraction obtained from the thermal-oxidative pyrolysis of waste tires. The study covers the analysis of the composition of rubber products before and after pyrolysis at a temperature of 750-850 °C. A chemical analysis of the gaseous, liquid and solid phases of pyrolysis products was also carried out. The ignition temperatures of gaseous products, their percentage content, as well as the optimal boiling temperatures of the resulting condensates were determined. X-ray analysis showed that the solid carbon residue consists of calcite (7.50%), amorphous carbon (87.24%), ankerite (Ca(Mg, Fe)[CO_{3 …}

Dеvеlоpmеnt Аnd Simulаtiоn Оf Аutоmаtiс Tеmpеrаturе Соntrоl Sуstеms Fоr Sоlаr Drуеrs, Sarvar Rejabov, Botir Shukurillayevich Usmonov, Komil Usmanov

Chemical Technology, Control and Management

Thе utilizаtiоn оf sоlаr еnеrgу in thе drуing оf аgriсulturаl prоduсts is соnsidеrеd signifiсаnt duе tо its еnеrgу еffiсiеnсу аnd еnvirоnmеntаl friеndlinеss. Hоwеvеr, trаditiоnаl drуing mеthоds fасе сhаllеngеs in mаintаining stаblе tеmpеrаturе аnd humiditу lеvеls, whiсh саn lеаd tо rеduсеd prоduсt quаlitу аnd dесrеаsеd prосеss еffiсiеnсу. Tо аddrеss thеsе issuеs, thе implеmеntаtiоn оf аutоmаtiс соntrоl sуstеms is еssеntiаl. In dеvеlоping аn аutоmаtiс tеmpеrаturе соntrоl sуstеm fоr sоlаr drуеrs, thе hеаt аnd mаss trаnsfеr prосеssеs wеrе prесisеlу mоdеlеd. Thе primаrу pаrаmеtеrs оf thе drуing prосеss, suсh аs prоduсt tеmpеrаturе аnd mоisturе соntеnt dуnаmiсs, wеrе еxprеssеd thrоugh mаthеmаtiсаl еquаtiоns. PID аnd Fuzzу …

Modeling Of Analog-To-Digital Converter In Signal Processing, Ravshan Aliev, A.U. Djalilov

Chemical Technology, Control and Management

This article is devoted to the study of the modeling process of analog-to-digital converters (ADCs) that process signals, one of the main parts of control system elements and devices. As we know, ADCs are an important part of modern control systems. During the research, the main stages of analog signal conversion were analyzed, i.e. discretization, quantization, coding. A classification of analog-to-digital conversion methods was made and the advantages and disadvantages of each were identified. Also, the characteristics and parameters of ADC were studied, their impact on ADCs performance was evaluated, and it was determined that certain characteristics should be taken …

Principles And Models Of Construction Of Linear Motion Actuators With Holonomic Structure For Intelligent Robot Movement, Matyokubov Nurbek Rustamovich, Temurbek Omonboevich Rakhimov, Yusupov Bekmurod Bayotovich

Chemical Technology, Control and Management

This article is devoted to the principles and models of building linear motion actuators with holonomic structure for the movement of intelligent robots. Also, the classification of the elements of the linear movement performance according to their interconnections and technical characteristics, taking into account their physical characteristics, was seen. A morphological matrix of the construction of holonomic structured linear motion performance elements based on the classification according to the considered technical specifications is presented. The given morphological matrix of linear motion actuators serves to develop new actuators for intelligent mechatronic and robotic systems. Based on the morphological matrix of the …

Application Of An Adaptive Neuro-Fuzzy Inference System To Control The Wastewater Treatment Process, Jaloliddin Abdurazzakovich Eshbobaev, Bakhodir Tajiddinovich Khamidov, Marcos Torices Fallanza

Chemical Technology, Control and Management

This study explores the application of an Adaptive Neuro-Fuzzy Inference System (ANFIS) for controlling wastewater treatment processes using ion-exchange resins. It addresses the critical challenges of water scarcity and pollution by enhancing the regulation of water hardness (H) and Total Dissolved Solids (TDS). Using a pilot laboratory device and experimental data from the mixed wastewater of the Kungrad Soda Plant in Uzbekistan, an ANFIS model was developed in MATLAB to automate process control. The model leverages water hardness and TDS as input parameters to regulate the water flow rate by servo valve opening degree, ensuring precise and efficient treatment. Compared …

Enhancing The Mechanical Properties Of Sla 3d-Printed Bio-Resin From Linseed Oil Using Cellulose And Lignin Biopolymers, Chukwunonso A. Ikedionu

College of Graduate Studies: Theses & Dissertations

Abstract

This research explores the development of bio resin from linseed oil by the process of epoxidation and acrylation to produce acrylated epoxidized linseed oil (AELO). Lignin and cellulose biopolymers were added as reinforcement at varying weight fractions of 1 wt.%, 2.5 wt.%, and 5 wt.%, and their mechanical performance was compared against pure AELO. The formulations were printed using an Elegoo SLA 3D printer to create standardized test specimens like tensile bars, compression cylinders, and hardness blocks, which were all prepared according to the ASTM testing standard.

The results indicate that reinforcement effects depend on both filler type and …

Pla Polymer Binder In Core Production - Influence On Final Casting Dimensions, Artur Soroczyński, Krzysztof Rechowicz

Virginia Digital Maritime Center (VDMC) Faculty Publications

The foundry industry is seeking an ecological alternative to synthetic molding resins. This study evaluates the technological properties of core sands bonded with biodegradable polylactide (PLA). Cores prepared on a 2% quartz sand matrix were subjected to casting processes using two alloys with extremely different pouring temperatures: gray cast iron (approx. 1200 °C) and AK11 silumin (approx. 710 °C). The research methodology included macroscopic assessment, dimensional analysis using 3D scanning (GOM Inspect), and qualitative knock-out assessment supported by numerical temperature field simulation. The results showed that the high crystallization temperature of cast iron leads to complete thermal degradation of the …

Effect Of Alkyd And Polyester Resin Compositions On Corrosion Resistance, Blistering, And Adhesion In Utilization Of Oily Sludge As Anti-Rust Coating Material, Gerets Land Kakalang, Yohanes David Kristianto, Johny Wahyuadi Mudaryoto

Journal of Materials Exploration and Findings

Oil sludge is a waste derived from upstream and downstream activities of the oil and gas industry which is estimated at 10,000 tonnes generated from all PERTAMINA downstream activities spread across various fields, processing units and depots throughout Indonesia. Oil sludge has the same characteristics as asphalt, where asphalt in previous studies can be used as an anti-rust coating, so that the handling of oily sludge can be topped up by reusing and having its own added value. The purpose of this research is to utilise waste oily sludge as an alternative anti-rust coating material and compare alkyd resin and …

Mathematical Modelling Of The Solar Drying Of Apricot, Sarvar Rejabov, Botir Shukurillayevich Usmonov, Asqar Artikov, Komil Usmanov

Chemical Technology, Control and Management

Agricultural products provide significant growth in export earnings for many countries and provide food globally. Fruits and vegetables are perishable foods due to their high moisture content. Therefore, most agricultural products require post-harvest processing such as drying to extend the shelf life of fruits and vegetables and maintain nutrient quality. Solar drying is widely used for this purpose. Ambient temperature, humidity and solar radiation affect the drying time and quality of agricultural products, especially apricots, in solar dryers. The experiments were carried out in the same place (Tashkent, Uzbekistan) and in the same time interval. When the mass of apricots …

Experimental Study Of The Ultrasonic Extraction Process Of Plant Raw Materials, Azamat Bakir Ogli Usenov, Doston Ishmuxammat Ogli Samandarov, Qobil Akmal Ogli Mukhiddinov, Jasur Esirgapovich Safarov Dcs

Chemical Technology, Control and Management

In-depth scientific research is being conducted around the world aimed at developing the scientific and methodological foundations of energy-saving extractors, processing medicinal plants, increasing the efficiency of modern technologies, processes and equipment for obtaining high-quality pharmaceutical raw materials rich in biologically active substances. Energy-saving extractors, developed in conjunction with the extraction process of medicinal plants, are introduced into the industry using scientifically proven technology. At the global level, special attention is paid to the creation of intelligent designs of innovative extraction plants that operate using ultrasonic waves, allowing the extraction of medicinal components of plants.

Clustering Algorithm Based On Similarity Of Objects, Akhram Khasanovich Nishanov, Alisher Tulkunovich Tursunov, Fayzullo Farhod O'G'Li Ollamberganov

Chemical Technology, Control and Management

The article discusses the problem of drug clustering. Initially, k classes are randomly formed and the resulting training sample is preprocessed, then the similarity between objects of each class is assessed based on the proximity function and the criterion for assessing the contribution of objects to the formation of their own class. It is usually expressed as a percentage and represents the degree of mutual similarity of objects of each class. In the next steps of the algorithm, first one object is taken from the first class and by adding it to all k classes, the contribution of this object …

Capacitive Sensors With Ultra-Small Capacitance For Smart Measurement And Control Systems, Rustam Baratov, Farrux Jabbor O'G'Li Ko'charov

Chemical Technology, Control and Management

This article discusses methods of low capacitance measurement of capacitive sensors. The results of the study of the amplitude-frequency (AF) and phase-frequency (PF) response of measurement circuits of capacitive sensors for low capacitances measurement, consisting of RC - differentiating elements are presented. The input and output parameters of the differentiating circuit and the complex transfer function are analyzed. The research results show that low capacitances measurement by measuring the rectangular pulses duration is the most effective measurement method.

Developing Decision-Making Models And Algorithms To Help Prevent Emergencies, Mizaakbar Xakkulmirzayevich Hudayberdiyev, Oybek Zokirovich Koraboshev

Chemical Technology, Control and Management

The article is devoted to the solution of the scientific issue of decision-making support for the prevention and elimination of the consequences of emergency situations. The relevance of this issue is related to the need to develop a theoretical basis for optimizing the risk of adverse effects on human health and the environment in connection with emergency situations, and a predictive model for the development of emergency situations and their prevention or elimination of their consequences. The optimization of the importance measure of signs for predicting the values of the factors of fire conditions has been carried out. In addition, …

Investigation Of The Parameters Of Semicylindrical Capacitive Sensor, Erkin Uljaev, Elyor Faxriddinovich Khudoyberdiev, Shohrukh Nurali O‘G‘Li Narzullayev

Chemical Technology, Control and Management

This study introduces a semicylindrical capacitive sensor, featuring an internal dielectric insulator, designed to measure moisture levels in bulk and other materials while in motion. The research employs numerical analysis to explore the sensor's capacitance variation and evaluate its performance. The change in capacitance of the semicylindrical capacitive sensor in the picofarad range is easily converted into a change in the frequency of the generator, which is implemented on an operational amplifier with feedback. The generator circuit is quite compact, and its output can be connected directly to the discrete input of a microcontroller without a matching element. Using the …

Investigation Of Heavy Metal Composition And Associated Health Risks From Selected Groundwater Wells In Temeke, Dar-Es-Salaam, Justin M. Jeremiah

Tanzania Journal of Engineering and Technology (TJET)

Water quality continues to be the challenge to residents in Dar es Salaam due to various anthropogenic activities in the city. This study was conducted to assess groundwater quality by determining concentrations of heavy metals. Both probability and Nonprobability sampling techniques were used to collect samples from 40 groundwater wells in 24 wards of Temeke municipal and analysed using Microwave Plasma Atomic Emission Spectrometer (Agilent 4210 MP-AES) at the Geochemistry Laboratory of the University of Dar es Salaam. Results indicated varying heavy metal concentrations ranging from 0.71 ± 0.08 to 6.64 ± 0.21 mg/l for As, 0.02 ± 0.01 to …

Development And Testing Of Small-Scale Flash Dryer For Maize Bran, Eden Ngowi

Tanzania Journal of Engineering and Technology (TJET)

Sun drying is the most common technique used to dry various food products due to its economic convenience. However, it is not effective owing to its unreliable nature leading to microbial deterioration and aflatoxin contamination of food. In Tanzania, about 1.3 million tonnes of maize bran are at risk of deterioration annually due to improper drying. The aim of this study was to design, fabricate and test an efficient small-scale flash dryer for maize bran. Using principles of material and energy balance, a small-scale flash dryer with a throughput of 500 kg of dry product per hour was designed resulting …

Inspection Planning Of Subsea Pipeline Using Risk-Based Inspection, Ni Luh Triska Adelia, Badrul Munir, Johny Wahyuadi Soedarsono

Journal of Materials Exploration and Findings

Pipelines are an important tool in oil and gas exploration. Pipeline is a transmission and liquid collection lines, including their accessories, which transport fluids from one plant to another. In transmission and collection process, there is a possibility of failure which can have minor to major impact on personnel injury, the environment and interrupt the business process. To maintain safety and to prevent accidents, the source and cause of failure needs to be calculated. Risk-based inspection (RBI) is a method that can be used to calculate the risk and determine the inspection planning both schedule and method, by combining the …

Optimizing The Expression Of Polyethylene Terephtalate Hydrolase-Encoding Synthetic Gene In Escherichia Coli Arctic Express (De3), Jocelyn Nataniel, Maria Ulfah, Dini Achnafani, Niknik Nurhayati, Gabriela Christy Sabbathini, Sri Rezeki Wulandari, Abinawanto Abinawanto, Is Helianti

Makara Journal of Science

The waste of polyethylene terephthalate (PET) plastic waste in Indonesia is a pressing concern due to its slow degradation and potential environmental damage. One promising solution is to utilize polyethylene terephthalate hydrolase from Ideonella sakaiensis (IsPETase), an enzyme that specifically degrades PET. However, inducing the expression of IsPETase synthetic gene in Escherichia coli BL21 (DE3) has been challenging because much of it remains insoluble. This study aimed to express IsPETase in E. coli Arctic Express (DE3) and optimize the conditions to enhance its production. First, pET22b(+)pelB-IsPETase was inserted into E. coli Arctic Express (DE3). The …

Ultrasonic Flow Meter Calibration Via The Internet Using An Analog-To-Digital Converter, Aliev Ravshan, A.U. Djalilov

Chemical Technology, Control and Management

The purpose of scientific research work is remote control of improving the metrological properties of the water flow measuring device. Therefore, the Arduino platform with an additional ESP8266 NodeMcu v3 and analog-to-digital converter, module was installed in the scientific article for automatic calibration/checking of ultrasonic flow meters used in irrigation networks. The module is integrated into a 32-bit microcontroller with low power consumption. The ESP8266 NodeMcu v3 module operates at 80 and 160 MHz clock frequencies, supports real-time operating system (RTOS), built-in Wi-Fi, and has a microstrip antenna on board. Through this, the data exchange between the computing equipment and …