Nanoscience and Nanotechnology Commons^™

Strain Engineering Via Amorphization And Recrystallization In Si/Ge Heterostructures, Yumi Park, Winnie Tan, Alejandro Strachan

Birck and NCN Publications

We use molecular dynamics with the reactive potential ReaxFF to study strain relaxation during the amorphization and recrystallization of silicon-germanium epitaxial nanolaminates. Starting with a coherent heterostructure with (010) Si/Ge interfaces and 3D periodic boundary conditions, we use local heating and quenching to amorphize half of the simulation cell with crystal-amorphous interfaces normal to [001]. We find strain relaxation along [001] as the crystalline Ge section expands into the amorphous material and crystalline Si contracts from it. The amount of strain relaxation correlates with the atomic transport from the amorphized Ge to Si section and increases as the periodic width …

Amorphous Interface Layer In Thin Graphite Films Grown On The Carbon Face Of Sic, R. Colby, M. L. Bolen, Michael A. Capano, E. A. Stach

Birck and NCN Publications

Cross-sectional transmission electron microscopy (TEM) is used to characterize an amorphous layer observed at the interface in graphite and graphene films grown via thermal decomposition of C-face 4H-SiC. The amorphous layer does not cover the entire interface, but uniform contiguous regions span microns of cross-sectional interface. Scanning transmission electron microscopy (STEM) images and electron energy loss spectroscopy (EELS) demonstrate that the amorphous layer is a carbon-rich composition of Si/C. The amorphous layer is clearly observed in samples grown at 1600 degrees C for a range of growth pressures in argon, but not at 1500 degrees C, suggesting a temperature-dependent formation …

Design Of A Gainp/Gaas Tandem Solar Cell For Maximum Daily, Monthly, And Yearly Energy Output, Alexander W. Haas, John R. Wilcox, Jeffery L. Gray, Richard J. Schwartz

Birck and NCN Publications

Solar concentrator cells are typically designed for maximum efficiency under the AM1.5d standard spectrum. While this methodology does allow for a direct comparison of cells produced by various laboratories, it does not guarantee maximum daily, monthly, or yearly energy production, as the relative distribution of spectral energy changes throughout the day and year. It has been suggested that achieving this goal requires designing under a nonstandard spectrum. In this work, a GaInP/GaAs tandem solar cell is designed for maximum energy production by optimizing for a set of geographically-dependent solar spectra using detailed numerical models. The optimization procedure focuses on finding …

Role Of Surface Orientation On Atomic Layer Deposited Al2o3/Gaas Interface Structure And Fermi Level Pinning: A Density Functional Theory Study, Ganesh Hegde, Gerhard Klimeck, Alejandro Strachan

Birck and NCN Publications

We investigate the initial surface reaction pathways in the atomic layer deposition (ALD) of Al2O3 on GaAs (111)A and (111)B substrates using precursors trimethylaluminum (TMA) and water to ascertain the effect of surface orientation on device performance. We find that the condition of the respective substrates prior to deposition of TMA and water has a major impact on the surface reactions that follow and on the resulting interface structure. The simulations explain the atomistic mechanism of the interfacial self-cleaning effect in ALD that preferentially removes As oxides. The electronic structure of the resulting atomic configurations indicates states throughout the bandgap …

Synthesis And Characterization Of Highly Textured Pt–Bi Thin Films, Xingzhong Li, Parashu Kharel, Shah R. Valloppilly, David J. Sellmyer

Nebraska Center for Materials and Nanoscience: Faculty Publications

Pt–Bi films were synthesized on glass and thermally oxidized silicon substrates by e-beam evaporation and annealing. The structures were characterized using X-ray diffraction (XRD) and transmission electron microscopy/selected area electron diffraction (TEM/SAED) techniques. Single-phase PtBi was obtained at an annealing temperature of 300°C, whereas a higher annealing temperature of 400°C was required to obtain the highly textured γ-PtBi2 phase. TEM/SAED analysis showed that the films annealed at 400°C contain a dominant γ-PtBi2 phase with a small amount of β-PtBi2 and α-PtBi2 phases. Both the PtBi and γ-PtBi2 phases are highly textured in these two kinds of film: the c-axis of …

Ferromagnetic Resonance On Ni Nanowire Arrays, Mircea Chipara, Ralph Skomski, Roger D. Kirby, David J. Sellmyer

Physics & Astronomy Faculty Publications

Ferromagnetic resonance investigations on Ni nanowires are reported. The angular dependence of the resonance line position is analyzed within a thermodynamic approach that includes shape anisotropy (ellipsoids of revolution), magnetocrystalline anisotropies (cubic and uniaxial), and dipole–dipole interactions. The results are supported by hysteresis loops, obtained on the same sample.

Rehabilitation And Exercise Machine, Judith M. Burnfield, Yu Shu, Adam P. Taylor, Thad W. Buster, Carl Nelson

Department of Mechanical and Materials Engineering: Faculty Publications

An improved rehabilitation and exercise machine is provided which allows a person with physical limitations, disabilities or chronic conditions to use the machine in order to rehabilitate their muscles, improve joint flexibility, and enhance cardiovascular fitness.

Development Of Dehydrogenase-Based Bioanode Using Poly(Phenosafranin)-Functionalized Swcnt Nanocomposites And Its Application To Ethanol Biosensor, S. Saleh Farhana, Okajima Takeyoshi, Lanqun Mao, Takeo Ohsaka

Journal of Electrochemistry

A New type of dehydrogenase-based amperometric ethanol biosensor was constructed using alcohol dehydrogenase (ADH) which was immobilized on the edge-plane pyrolytic graphite (EPPG) electrode modified with poly(phenosafranin)-functionalized single-walled carbon nanotube (PPS-SWCNT). The PPS-SWCNT modified EPPG electrode was prepared by electropolymerization of phenosafranin on the EPPG electrode which was previously coated with SWCNT. The performance of the ADH/PPS-SWCNT/EPPG electrode was evaluated using cyclic voltammetry and amperometry in the presence of ethanol. The fabricated ethanol biosensor provided a reasonable sensitivity of 2.0 μA cm–2 mM–1 and a low detection limit (36 μM) for the electrocatalytic oxidation of ethanol with a linear concentration …

Study On The Fluorescent Carbon Nanodots With Electrochemical Methods, Bao-Ping Qi, Yan-Min Long, Lei Bao, Cui Liu, Zhi-Ling Zhang, Dai-Wen Pang

Journal of Electrochemistry

Carbon nanodots are a new class of fluorescent nanoparticles with a carbon-based core, which possess wavelength-tunable luminescence, high photostability, resistance to photobleaching, water-solubility, and ease of bioconjugation. Owing to their attractive merits, carbon nanodots like other carbon nanomaterials such as fullerene, carbon nanotubes and graphene, have attracted much attention. In addition, carbon nanodots can be inexpensively produced by electrochemical methods with simple post-processing under mild conditions. Electrochemical approaches have unique advantages in the analysis of surface structures and luminescence mechanism of materials. In this review, recent advances in electrochemical methods used for the synthesis and luminescence mechanism of fluorescent carbon …

Study On The Electrochemical Behaviors Of Gc Electrode Modified With Carbon Nanotube-Polyelectrolytes And Its Application For Rutin Detection, Liang Hua, Xia-Qin Wu, Rong Wang

Journal of Electrochemistry

The electrochemical behaviors of rutin and ascorbic acid at single-wall carbon nanotube and polyelectrolytes (dimethyl-diallylammonium chloride, PDDA) film modified glassy carbon electrode was investigated. The cyclic voltammetric results showed that electron transfer of rutin at PDDA/SWCNTs/GC modified electrode is an adsorption-controlled process. The separation of oxidation peak potentials of rutin and ascorbic acid was more than 200 mV. The rutin concentration in the presence of AA were detected by differential pulse voltammetry (DPV). The experimental results indicated that the PDDA/SWCNTs/GC modified electrode can be used for the detection of rutin in the presence of high concentration of AA. The DPV …

Surface Diffusion Of Adsorptive Species On Gold Nanoelectrodes, Bao-Fa Su, Wei Wang, Dong-Ping Zhan, Bin Ren, Zhong-Qun Tian

Journal of Electrochemistry

Gold nanoelectrodes were prepared successfully by a programmed laser puller. The Faraday adsorptions of oxygen and iodine, and the underpotential deposition of lead on the gold nanoelectrodes were investigated. The results showed that the active areas of nanoelectrodes were dramatically higher than their appearant geometry areas, which is caused by the surface diffusion of adsorptive species from the nanoscale gold/electrolyte interface to the adjacent gold surface.

Strain Effects On The Phonon Thermal Properties Of Ultra-Scaled Si Nanowires, Abhijeet Paul, Gerhard Klimeck

Birck and NCN Publications

The impact of uniaxial and hydrostatic stress on the ballistic thermal conductance (jl) and the specific heat (Cv) of [100] and [110] Si nanowires are explored using a Modified Valence Force Field phonon model. An anisotropic behavior of jl and isotropic nature of Cv under strain are predicted for the two wire orientations. Compressive (tensile) strain decreases (increases) Cv. The Cv trend with strain is controlled by the high energy phonon sub-bands. Dominant contribution of the low/mid (low/high) energy bands in [100] ([110]) wire and their variation under strain governs thebehaviorofjl.VC 2011AmericanInstituteofPhysics.

Mechanism Of Thermal Conductivity Reduction In Few-Layer Graphene, Druv Singh, Jayathi Y. Murthy, Timothy S. Fisher

Birck and NCN Publications

Using the linearized Boltzmann transport equation and perturbation theory, we analyze the reduction in the intrinsic thermal conductivity of few-layer graphene sheets accounting for all possible three-phonon scattering events. Even with weak coupling between layers, a significant reduction in the thermal conductivity of the out-of-plane acoustic modes is apparent. The main effect of this weak coupling is to open many new three-phonon scattering channels that are otherwise absent in graphene. However, reflection symmetry is only weakly broken with the addition of multiple layers, and out-of-plane acoustic phonons still dominate thermal conductivity. We also find that reduction in thermal conductivity is …

Relaxation Of Optically Excited Carriers In Graphene, Raseong Kim, Vasili Perebeinos, Phaedon Avouris

Birck and NCN Publications

We explore the relaxation of photoexcited graphene by solving a transient Boltzmann transport equation with electron-phonon (e-ph) and electron-electron (e-e) scattering. Simulations show that when the excited carriers are relaxed by e-ph scattering only, a population inversion can be achieved at energies determined by the photon energy. However, e-e scattering quickly thermalizes the carrier energy distributions washing out the negative optical conductivity peaks. The relaxation rates and carrier multiplication effects are presented as a function of photon energy, graphene doping, and dielectric constant.

Entanglement Dynamics Of One-Dimensional Driven Spin Systems In Time-Varying Magnetic Fields, Bedoor Alkurtass, Gehad Sadiek, Sabre Kais

Birck and NCN Publications

We study the dynamics of nearest-neighbor entanglement for a one-dimensional spin chain with a nearest-neighbor time-dependent Heisenberg coupling J(t) between the spins in the presence of a time-dependent external magnetic field h(t) at zero and finite temperatures. We consider different forms of time dependence for the coupling and magnetic field: exponential, hyperbolic, and periodic. Solving the system numerically, we examined the system-size effect on the entanglement asymptotic value. It was found that, for a small system size, the entanglement starts to fluctuate within a short period of time after applying the time-dependent coupling. The period of time increases as the …

Electrochemical Synthesis Of Single Crystal Metal Nanowires, Nan Li

Master's Theses

Electrodeposition is an efficient and economical approach for template synthesis of one-dimensional (1D) nanostructured materials. Based on the porous membranes as templates during electrodeposition, metallic nanowires, nanorods, and nanotubes can overcome the geometrical restrictions to be inserted into the nanometric recesses with both diameter and length well controlled by tuning the size and thickness of the templates.

In this work, the morphology, growth rate and texture of copper nanowires prepared with templates were investigated by the controlled parameters in various experiments. Cu nanowire arrays with preferential orientations can be successfully synthesized into the Anodic Aluminum Oxide (AAO) templates with optimized …

Anti-Stokes Fluorescence Imaging Of Microscale Thermal Fields In Thin Films, A. N. Kuzmin, A. Baev, A. V. Kachynski, Timothy S. Fisher, Ali Shakouri, P. N. Prasad

Birck and NCN Publications

We demonstrate that the in-plane thin film heat transport can be accurately mapped via confocal anti-Stokes fluorescence imaging using fluorescent dye probes and nanoheaters. We employ 3D finite elements analysis to evaluate the thermal conductivity of a control sample and to assess the validity of a point heat source approximation. We have found that this approximation is adequate with use of a tightly focused laser beam, providing a robust means for determining the thermal conductivity of a sample under investigation. (C) 2011 American Institute of Physics. [doi:10.1063/1.3606429]

Computational Study Of The Seebeck Coefficient Of One-Dimensional Composite Nano-Structures, Raseong Kim, Mark S. Lundstrom

Birck and NCN Publications

The Seebeck coefficient (S) of composite nano-structures is theoretically explored within a self-consistent electro-thermal transport simulation framework using the non-equilibrium Green's function method and a heat diffusion equation. Seebeck coefficients are determined using numerical techniques that mimic experimental measurements. Simulation results show that, without energy relaxing scattering, the overall S of a composite structure is determined by the highest barrier within the device. For a diffusive, composite structure with energy relaxation due to electron-phonon scattering, however, the measured S is an average of the position-dependent values with the weighting factor being the lattice temperature gradient. The results stress the importance …

Observation Of Nonclassical Scaling Laws In The Quality Factors Of Cantilevered Carbon Nanotube Resonators, Ajit Vallabhaneni, Jeff Rhoads, Jayathi Y. Murthy, Xiulin Ruan

Birck and NCN Publications

This work examines the quality factors (Q factors) of resonance associated with the axial and transverse vibrations of single-wall carbon nanotube (SWCNT) resonators through the use of molecular dynamics (MD) simulation. Specifically, the work investigates the effect of device length, diameter, and chirality, as well as temperature, on the resonant frequency and quality factor of these devices and benchmarks the results of MD simulations against classical theories of energy dissipation. The quality factor (Q) associated with transverse vibration is found to increase with increasing device length (Q similar to L(theta), where 0.8 < theta < 1.4) and decrease with increasing device diameter (Q similar to D(-mu), where 1.4 < mu < 1.6), while the Q associated with axial vibration is almost independent of length and diameter. We show that to accurately predict temperature dependence of Q, the external and internal energies need to be properly decomposed, and temperature quantum correction should be performed. For both vibrational modes, Q shows a temperature dependence Q similar to T(-alpha), where alpha > 1 when below Debye temperature due to quantum …

Effects Of Mass Layer Dimension On A Finite Quartz Crystal Microbalance, Y. P. Kong, Jinxi Liu, Huijing He, Jiashi Yang

Department of Mechanical and Materials Engineering: Faculty Publications

In this paper, we investigate free thickness-shear and thickness-twist vibrations of a finite crystal resonator of AT-cut quartz carrying a thin mass layer at the central portion of its top surface operating as a quartz crystal microbalance. The equations of anisotropic elasticity are used with the omission of the small elastic constant c56. An analytical solution is obtained using Fourier series from which the resonant frequencies, mode shapes and vibration confinement by the mass layer are calculated and examined.

Domain Size And Structure In Exchange Coupled [Co/Pt]/Nio/[Co/Pt] Multilayers, Andrew G. Baruth, Shireen Adenwalla

Shireen Adenwalla Papers

We investigate the competing effects of interlayer exchange coupling and magnetostatic coupling in the magnetic heterostructure ([Co/Pt]/NiO/[Co/Pt]) with perpendicular magnetic anisotropy (PMA). This particular heterostructure is unique among coupled materials with PMA in directly exhibiting both ferromagnetic and antiferromagnetic coupling, oscillating between the two as a function of spacer layer thickness. By systematically tuning the coupling interactions via a wedge-shaped NiO spacer layer, we explore the energetics that dictate magnetic domain formation using high resolution magnetic force microscopy coupled with the magneto-optical Kerr effect. This technique probes the microscopic and macroscopic magnetic behavior as a continuous function of thickness and …

Modeling Of Strain Effect On Thermal And Electrical Transport Properties Of Si/Ge Nanocomposites And Its Applications, Yaoyao Xu

All Dissertations

Nanocomposites are composite materials which incorporate nanosized particles, platelets or fibers. The addition of nanosized phases into the bulk matrix can lead to significantly different material properties compared to their macrocomposite counterparts. Due to their extraordinary properties, nanocomposites promise new applications in many fields such as ultra-high strength and ultra-light automotive parts, non-linear optics, biomedical applications, sensors and actuators, and thermoelectric devices. The design and fabrication of nanocomposite structures, devices and systems can be accelerated by developing accurate and efficient computational tools that can describe the properties and behavior of the nanocomposites. However, the development of such tools is challenging …

Atomic-Layer-Deposited Al2o3 On Bi2te3 For Topological Insulator Field-Effect Transistors, Han Liu, Peide D. Ye

Birck and NCN Publications

We report dual-gate modulation of topological insulator field-effect transistors (TI FETs) made on Bi2Te3 thin flakes with integration of atomic-layer-deposited (ALD) Al2O3 high-k dielectric. Atomic force microscopy study shows that ALD Al2O3 is uniformly grown on this layer-structured channel material. Electrical characterization reveals that the right selection of ALD precursors and the related surface chemistry play a critical role in device performance of Bi2Te3 based TI FETs. We realize both top-gate and bottom-gate control on these devices, and the highest modulation rate of 76.1% is achieved by using simultaneous dual gate control. (C) 2011 American Institute of Physics. [doi:10.1063/1.3622306]

Seismic Characterization Of Select Engineered Nanoparticles In Essentially Saturated Glass Beads, Mohamed Nihad Rajabdeen

UNLV Theses, Dissertations, Professional Papers, and Capstones

A laboratory testing apparatus was developed for the study of seismic body wave propagation through nanoparticles dispersed in pore fluid that is essentially saturating glass beads. First, the responses of water-saturated glass bead specimens were studied to establish baseline signatures. Then the seismic responses in the presence of engineered nanoparticles of various concentrations dispersed in the pore fluid of the specimen chamber were studied to observe variances from baseline.

The testing apparatus incorporates piezoceramic bender elements to actuate and receive seismic body waves through a cylindrical column filled with glass beads and back-saturated at ambient pressure with liquid. The system …

Dislocation Pinning Effects Induced By Nano-Precipitates During Warm Laser Shock Peening: Dislocation Dynamic Simulation And Experiments, Yiliang Liao, Chang Ye, Huang Gao, Bong-Joong Kim, Sergey Suslov, Eric A. Stach, Gary J. Cheng

Birck and NCN Publications

Warm laser shock peening (WLSP) is a new high strain rate surface strengthening process that has been demonstrated to significantly improve the fatigue performance of metallic components. This improvement is mainly due to the interaction of dislocations with highly dense nanoscale precipitates, which are generated by dynamic precipitation during the WLSP process. In this paper, the dislocation pinning effects induced by the nanoscale precipitates during WLSP are systematically studied. Aluminum alloy 6061 and AISI 4140 steel are selected as the materials with which to conduct WLSP experiments. Multiscale discrete dislocation dynamics (MDDD) simulation is conducted in order to investigate the …

Vertical Track Modulus Trending, Shane Michael Farritor, Sheng Lu

Department of Mechanical and Materials Engineering: Faculty Publications

Systems and methods for determining a trend in Vertical track modulus are disclosed in accordance with embodiments of the present invention. Vertical deflection data is collected along a particular section of railroad track. A first set of Vertical track modulus is determined, based in part, on the collected vertical deflection data. At a second time, vertical deflection data is again collected along the particular section of railroad track to be used in determining a second set of vertical track modulus. At least the first and second sets of Vertical track modulus are analyzed to determine a math ematical algorithm that …

Periodically Changing Morphology Of The Growth Interface In Si, Ge, And Gap Nanowires, C-Y Wen, J. Tersoff, K. Hillerich, M.C. Reuter, J. H. Park, S. Kodambaka, Eric Stach, F.M. Ross

Birck and NCN Publications

Nanowire growth in the standard < 111 > direction is assumed to occur at a planar catalyst-nanowire interface, but recent reports contradict this picture. Here we show that a nonplanar growth interface is, in fact, a general phenomenon. Both III-V and group IV nanowires show a distinct region at the trijunction with a different orientation whose size oscillates during growth, synchronized with step flow. We develop an explicit model for this structure that agrees well with experiment and shows that the oscillations provide a direct visualization of catalyst supersaturation. We discuss the implications for wire growth and structure.

Synthesis And Characterization Of Cdse-Zns Core-Shell Quantum Dots For Increased Quantum Yield, Joshua James Angell

Master's Theses

Quantum dots are semiconductor nanocrystals that have tunable emission through changes in their size. Producing bright, efficient quantum dots with stable fluorescence is important for using them in applications in lighting, photovoltaics, and biological imaging. This study aimed to optimize the process for coating CdSe quantum dots (which are colloidally suspended in octadecene) with a ZnS shell through the pyrolysis of organometallic precursors to increase their fluorescence and stability. This process was optimized by determining the ZnS shell thickness between 0.53 and 5.47 monolayers and the Zn:S ratio in the precursor solution between 0.23:1 and 1.6:1 that maximized the relative …

Nanofabrication Of Halloysite-Pcl Composite Scaffolds And Functionalization Of Titanium For Tissue Regeneration, Shraddha Parshottambhai Patel

Doctoral Dissertations

Major medical needs may be achieved through regenerative medicine. Nanotechnology has triggered a research revolution in many important areas such as the biomedical sciences and bioengineering at the molecular level which has grown significantly due to the availability of new analytical applications and tools based on nanotechnology. Clinical conditions and diseases being targeted by nanotechnology research include burns, Alzheimer's and Parkinson's disease, implant failure, improved wound healing, birth defects, osteoporosis and congestive heart defects. Therapeutic use of growth factors and drugs to stimulate the production and/or function of endogenous cells represents a key area of regenerative medicine. The development of …

Direct Simulation Monte Carlo Study Of Effects Of Thermal Nonuniformities In Electron-Beam Physical Vapor Deposition, A. Venkattraman, Alina A. Alexeenko

Birck and NCN Publications

In a typical electron-beam physical vapor deposition system, there is limited control over how the high-power electron beam heats the metal surface. This leads to thermal nonuniformities at the melt. Three-dimensional direct simulation Monte Carlo simulations were performed with the aim of quantifying the effect of such spatial variations of source temperature in thin film depositions using an electron-beam physical vapor deposition system. The source temperature distribution from a typical deposition process was used in the direct simulation Monte Carlo simulations performed for various mass flow rates. The use of an area-averaged temperature is insufficient for all mass flow rates …