Nanoscience and Nanotechnology Commons^™

Effects Of Electrode Off Centre On Trapped Thickness-Shear Modes In Contoured At-Cut Quartz Resonators, Junjie Shi, Cuiying Fan, Minghao Zhao, Jiashi S. Yang

Department of Mechanical and Materials Engineering: Faculty Publications

We investigated thickness-shear vibrations of a contoured, AT-cut quartz resonator with a pair of electrodes displaced from the resonator centre. The scalar differential equations by Stevens and Tiersten for thickness-shear vibrations of electroded and unelectroded quartz plates were employed. Based on the variational formulation of the scalar differential equations established in a previous paper and the variation-based Ritz method with trigonometric functions as basis functions, free vibration resonance frequencies and trapped thickness-shear modes were obtained. The effects of the electrode off centre on resonance frequencies and mode shapes were examined. When the electrode off centre is about one hundredth of …

Focal Adhesion Kinase Regulation In Stem Cell Alignment And Spreading On Nanofibers, Mohammad Nahid Andalib, Jeong Soon Lee, Ligyeom Ha, Yuris A. Dzenis, Jung Yul Lim

Department of Mechanical and Materials Engineering: Faculty Publications

While electrospun nanofibers have demonstrated the potential for novel tissue engineering scaffolds, very little is known about the molecular mechanism of how cells sense and adapt to nanofibers. Here, we revealed the role of focal adhesion kinase (FAK), one of the key molecular sensors in the focal adhesion complex, in regulating mesenchymal stem cell (MSC) shaping on nanofibers. We produced uniaxially aligned and randomly distributed nanofibers from poly(L-lactic acid) to have the same diameters (about 130 nm) and evaluated MSC behavior on these nanofibers comparing with that on flat PLLA control. C3H10T1/2 murine MSCs exhibited upregulations in FAK expression and …

Optical Analysis And Fabrication Of Micro And Nanoscale Plasmonically Enhanced Devices, Avery M. Hill

Physics Undergraduate Honors Theses

Plasmonic nanostructures have been shown to act as optical antennas that enhance optical devices due to their ability to focus light below the diffraction limit of light and enhance the intensity of the incident light. This study focuses on computational electromagnetic (CEM) analysis of two devices: 1) GaAs photodetectors with Au interdigital electrodes and 2) Au thin-film microstructures. Experiments showed that the photoresponse of the interdigital photodetectors depend greatly on the electrode gap and the polarization of the incident light. Smaller electrode gap and transverse polarization give rise to a larger photoresponse. It was also shown that the response from …

Optical Analysis And Fabrication Of Micro And Nanoscale Plasmonically Enhanced Devices, Avery M. Hill

Mechanical Engineering Undergraduate Honors Theses

Plasmonic nanostructures have been shown to act as optical antennas that enhance optical devices due to their ability to focus light below the diffraction limit of light and enhance the intensity of the incident light. This study focuses on computational electromagnetic (CEM) analysis of two devices: 1) GaAs photodetectors with Au interdigital electrodes and 2) Au thin-film microstructures. Experiments showed that the photoresponse of the interdigital photodetectors depend greatly on the electrode gap and the polarization of the incident light. Smaller electrode gap and transverse polarization give rise to a larger photoresponse. It was also shown that the response from …

Atomic Force Microscopy Based Dna Analysis, Drew Creighton

Mechanical Engineering Undergraduate Honors Theses

This report explores dry and wet scanning of a surface and DNA pickup using an AFM, as well as fluorescent staining of DNA. Dry and wet scans of DNA were obtained using a cantilever AFM tip in tapping mode. Dry scans were found to be clearer than wet scans; however, the drying process was found to decrease the thickness of DNA 2–4 times less than its original thickness. Alternately, wet scans were found to be less clear than dry scans and introduced more noise into the images obtained. Additionally, DNA kept its initial thickness during wet scanning. DNA was capable …

Al/Ti Nanostructured Multilayers: From Mechanical, Tribological, To Corrosion Properties, Sina Izadi

USF Tampa Graduate Theses and Dissertations

Nanostructured metallic multilayers (NMMs) are well-known for their high strength in smaller bilayer thicknesses. Six Al/Ti (NMM) with different individual layer thickness were tested for their mechanical hardness using a nanoindentation tool. Individual layer thicknesses were chosen carefully to cover the whole confined layer slip (CLS) model. Nano-hardness had a reverse relation with the square root of individual layer thickness and reached a steady state at ~ 5 nm bilayer thickness. Decreasing the layer bilayer thickness from ~ 104 nm to ~ 5 nm, improved the mechanical hardness up to ~ 101%. Residual stresses were measured using grazing incident X-ray …

Molecular Combing Of Dna Nanofibers And Comparison To Electrospinning, Tanner L. Buresh

UCARE: Research Products

The goal of these experiments was to create DNA nanofibers through the method of molecular combing (MC) and then compare the MC fibers to fibers created with electrospinning (ES). The experiment was designed and initial samples were created. After confirming that the method would succeed in creating DNA fibers, several parametric studies were performed in order to optimize the experiment and create the most uniform fibers possible. The parametric studies were done on the following variables: substrate material, pH level of DNA solution, and DNA solution concentration. After completion of all experiments, it was determined that although fibers could be …

Ultra-Thin Boron Nitride Films By Pulsed Laser Deposition: Plasma Diagnostics, Synthesis, And Device Transport, Nicholas Robert Glavin

Open Access Dissertations

This work describes, for the first time, a pulsed laser deposition (PLD) technique for growth of large area, stoichiometric ultra-thin hexagonal and amorphous boron nitride for next generation 2D material electronics. The growth of boron nitride, in this case, is driven by the high kinetic energies and chemical reactivities of the condensing species formed from physical vapor deposition (PVD) processes, which can facilitate growth over large areas and at reduced substrate temperatures. The use of optical emission spectroscopy during plasma growth provides insight into chemistry, kinetic energies, time of flight data, and spatial distributions within a PVD plasma plume ablated …

Design And Testing Of Robotic Capsule Biosensors In The Small Intestine, Zachary Bram

Robotics and Mechanical Systems Design

Biosensors are a tool that is growing in usage and is sought out by doctors and patients alike for being a non-invasive method to monitor health. The data that can be collected from these sensors can be analyzed by doctors that are away from patients, or even by patients that do not have the ability to see a doctor. The purpose of this work is to design and test a biosensor capsule that can attach itself to the inner wall of the small intestine for a short period of time before exiting the body. This research project was a continuation …

Method For Hyper-Polarizing Nuclear Spns At Arbtrary Magnetic Felds, Carlos A. Meriles, Daniela Pagliero, Abdelghani Laraoui

Department of Mechanical and Materials Engineering: Faculty Publications

A method of dynamically polarizing the nuclear spin host of nitrogen-vacancy (NV) centers in diamond is provided. The method uses optical, microwave and radio-frequency pulses to recursively transfer spin polarization from the NV electronic spin. Nitrogen nuclear spin initialization approaching 80% at room temperature is demonstrated both in ensemble and single NV centers without relying on level anti-crossings. This makes the method applicable at arbitrary magnetic fields.

Temperature-Dependent Helium Ion-Beam Mixing In An Amorphous Sioc/Crystalline Fe Composite, Qing Su, Lloyd Price, Lin Shao, Michael Nastasi

Department of Mechanical and Materials Engineering: Faculty Publications

Temperature dependent He-irradiation-induced ion-beam mixing between amorphous silicon oxycarbide (SiOC) and crystalline Fe was examined with a transmission electron microscope (TEM) and via Rutherford backscattering spectrometry (RBS). The Fe marker layer (7.2 ± 0.8 nm) was placed in between two amorphous SiOC layers (200 nm). The amount of ion-beam mixing after 298, 473, 673, 873, and 1073 K irradiation was investigated. Both TEM and RBS results showed no ion-beam mixing between Fe and SiOC after 473 and 673 K irradiation and a very trivial amount of ion-beam mixing (~2 nm) after 298 K irradiation. At irradiation temperatures higher than 873 …

Expanded 3d Nanofiber Scaffolds: Cell Penetration, Neovascularization, And Host Response, Jiang Jiang, Zhuoran Li, Hongjun Wang, Yue Wang, Mark A. Carlson, Matthew J. Teusink, Matthew R. Macewan, Linxia Gu, Jingwei Xie

Department of Mechanical and Materials Engineering: Faculty Publications

Herein, a robust method to fabricate expanded nanofiber scaffolds with controlled size and thickness using a customized mold during the modified gas-foaming process is reported. The expansion of nanofiber membranes is also simulated using a computational fluid model. Expanded nanofiber scaffolds implanted subcutaneously in rats show cellular infiltration, whereas non-expanded scaffolds only have surface cellular attachment. Compared to unexpanded nanofiber scaffolds, more CD68+ and CD163+ cells are observed within expanded scaffolds at all tested time points post-implantation. More CCR7+ cells appear within expanded scaffolds at week 8 post-implantation. In addition, new blood vessels are present within the expanded scaffolds at …

Comparison Between Direct And Reverse Electroporation Of Cells In Situ: A Simulation Study, Leila Towhidi, Delaram Khodadadi, Nataly Maimari, Ryan M. Pedrigi, Henry Ip, Zoltan Kis, Brenda R. Kwak, Tatiana W. Petrova, Mauro Delorenzi, Rob Krams

Department of Mechanical and Materials Engineering: Faculty Publications

The discovery of the human genome has unveiled new fields of genomics, transcriptomics, and proteomics, which has produced paradigm shifts on how to study disease mechanisms, wherein a current central focus is the understanding of how gene signatures and gene networks interact within cells. These gene function studies require manipulating genes either through activation or inhibition, which can be achieved by temporarily permeabilizing the cell membrane through transfection to deliver cDNA or RNAi. An efficient transfection technique is electroporation, which applies an optimized electric pulse to permeabilize the cells of interest. When the molecules are applied on top of seeded …

Floating-Gate Transistor Photodetector With Light Absorbing Layer, Jinsong Huang, Yongbo Yuan

Department of Mechanical and Materials Engineering: Faculty Publications

A field effect transistor photodetector that can operate in room temperature includes a source electrode, a drain electrode, a channel to allow an electric current to flow between the drain and source electrodes, and a gate electrode to receive a bias voltage for controlling the current in the channel. The photodetector includes a light-absorbing material that absorbs light and traps electric charges. The light-absorbing material is configured to generate one or more charges upon absorbing light having a wavelength within a specified range and to hold the one or more charges. The one or more charges held in the light-absorbing …

Active Stiffening Of F-Actin Network Dominated By Structural Transition Of Actin Filaments Into Bundles, Shengmao Lin, Xinwei Han, Gary C.P. Tsui, David Hui, Linxia Gu

Department of Mechanical and Materials Engineering: Faculty Publications

Molecular motor regulated active contractile force is key for cells sensing and responding to their mechanical environment, which leads to characteristic structures and functions of cells. The F-actin network demonstrates a two-order of magnitude increase in its modulus due to contractility; however, the mechanism for this active stiffening remains unclear. Two widely acknowledged hypotheses are that active stiffening of F-actin network is caused by (1) the nonlinear force-extension behavior of cross-linkers, and (2) the loading mode being switched from bending to stretching dominated regime. Direct evidence supporting either theory is lacking. Here we examined these hypotheses and showed that a …

Integration Of Flow Studies For Robust Selection Of Mechanoresponsive Genes, Nataly Maimari, Ryan M. Pedrigi, Alessandra Russo, Krysia Broda, Rob Krams

Department of Mechanical and Materials Engineering: Faculty Publications

Blood flow is an essential contributor to plaque growth, composition and initiation. It is sensed by endothelial cells, which react to blood flow by expressing >1000 genes. The sheer number of genes implies that one needs genomic techniques to unravel their response in disease. Individual genomic studies have been performed but lack sufficient power to identify subtle changes in gene expression. In this study, we investigated whether a systematic meta-analysis of available microarray studies can improve their consistency.

We identified 17 studies using microarrays, of which 6 were performed in vivo and 11 in vitro. The in vivo studies were …

Study Of Role Of Meniscus And Viscous Forces During Liquid-Mediated Contacts Separation, Prabin Dhital

All Graduate Theses, Dissertations, and Other Capstone Projects

Menisci may form between two solid surfaces with the presence of an ultra-thin liquid film. When the separation operation is needed, meniscus and viscous forces contribute to an adhesion leading stiction, high friction, possibly high wear and potential failure of the contact systems, for instance microdevices, magnetic head disks and diesel fuel injectors. The situation may become more pronounced when the contacting surfaces are ultra-smooth and the normal load is small. Various design parameters, such as contact angle, initial separation height, surface tension and liquid viscosity, have been investigated during liquid-mediated contact separation. However, how the involved forces will change …

Low Temperature Solution-Processed Sb:Sno2 Nanocrystals For Efficient Planar Perovskite Solar Cells, Yang Bai, Yanjun Fang, Yehao Deng, Qi Wang, Jingjing Zhao, Xiaopeng Zheng, Yang Zhang, Jinsong Huang

Department of Mechanical and Materials Engineering: Faculty Publications

Inorganic metal oxide electron-transport layers (ETLs) have the potential to yield perovskite solar cells with improved stability, but generally need high temperature to form conductive and defect-less forms, which is not compatible with the fabrication of flexible and tandem solar cells. Here, we demonstrate a facile strategy for developing efficient inorganic ETLs by doping SnO₂ nanocrystals (NCs) with a small amount of Sb using a low-temperature solution-processed method. The electrical conductivity was remarkably enhanced by Sb-doping, which increased the carrier concentration in Sb:SnO₂ NCs. Moreover, the upward shift of the Fermi level owing to doping results in improved …

Propagation Of Extensional Waves In A Piezoelectric Semiconductor Rod, C.L. Zhang, X. Y. Wang, W. Q. Chen, J. S. Yang

Department of Mechanical and Materials Engineering: Faculty Publications

We studied the propagation of extensional waves in a thin piezoelectric semiconductor rod of ZnO whose c-axis is along the axis of the rod. The macroscopic theory of piezoelectric semiconductors was used which consists of the coupled equations of piezoelectricity and the conservation of charge. The problem is nonlinear because the drift current is the product of the unknown electric field and the unknown carrier density. A perturbation procedure was used which resulted in two one-way coupled linear problems of piezoelectricity and the conservation of charge, respectively. The acoustic wave and the accompanying electric field were obtained from the equations …

Electrokinetic Phenomena In Pencil Lead-Based Microfluidics, Yashar Bashirzadeh, Venkat Maruthamuthu, Shizhi Qian

Mechanical & Aerospace Engineering Faculty Publications

Fabrication of microchannels and associated electrodes to generate electrokinetic phenomena often involves costly materials and considerable effort. In this study, we used graphite pencil-leads as low cost, disposable 3D electrodes to investigate various electrokinetic phenomena in straight cylindrical microchannels, which were themselves fabricated by using a graphite rod as the microchannel mold. Individual pencil-leads were employed as the micro-electrodes arranged along the side walls of the microchannel. Efficient electrokinetic phenomena provided by the 3D electrodes, including alternating current electroosmosis (ACEO), induced-charge electroosmosis (ICEO), and dielectrophoresis (DEP), were demonstrated by the introduced pencil-lead based microfluidic devices. The electrokinetic phenomena were characterized …

In Situ Microscopy Of The Self-Assembly Of Branched Nanocrystals In Solution, Eli Sutter, Peter Sutter, Alexei V. Tkachenko, Roman Krahne, Joost De Graaf, Milena Arciniegas, Liberato Manna

Department of Mechanical and Materials Engineering: Faculty Publications

Solution-phase self-assembly of nanocrystals into mesoscale structures is a promising strategy for constructing functional materials from nanoscale components. Liquid environments are key to self-assembly since they allow suspended nanocrystals to diffuse and interact freely, but they also complicate experiments. Real-time observations with single-particle resolution could have transformative impact on our understanding of nanocrystal self-assembly. Here we use real-time in situ imaging by liquid-cell electron microscopy to elucidate the nucleation and growth mechanism and properties of linear chains of octapod-shaped nanocrystals in their native solution environment. Statistical mechanics modelling based on these observations and using the measured chain-length distribution clarifies the …

Influence Of Shear Stress Magnitude And Direction On Atherosclerotic Plaque Composition, Ryan M. Pedrigi, Vikram V. Mehta, Sandra M. Bovens, Zahra Mohri, Christian Bo Poulsen, Willy Gsell, Jordi L. Tremoleda, Leila Towhidi, Ranil De Silva, Enrico Petretto, Rob Krams

Department of Mechanical and Materials Engineering: Faculty Publications

The precise flow characteristics that promote different atherosclerotic plaque types remain unclear. We previously developed a blood flow-modifying cuff for ApoE^−/− mice that induces the development of advanced plaques with vulnerable and stable features upstream and downstream of the cuff, respectively. Herein, we sought to test the hypothesis that changes in flow magnitude promote formation of the upstream (vulnerable) plaque, whereas altered flow direction is important for development of the downstream (stable) plaque. We instrumented ApoE^−/− mice (n=7) with a cuff around the left carotid artery and imaged them with micro-CT (39.6 μm resolution) eight to nine weeks …

Synthesis And Photonic Sintering Of Bioresorbable Zinc Nanoparticle Ink For Transient Electronics Manufacturing, Bikram K. Mahajan

Masters Theses

"Zinc is an essential 'trace element' that supports immune systems, and is required for DNA synthesis, cell division, and protein synthesis. Zinc nanoparticles (Zn NP) has antibacterial properties and potential to be used in biodegradable printed electronics devices. The research presented here is about the synthesis of Zn NP and their potential use in transient electronics devices. In Paper 1, a technique of room temperature synthesis of Zn NP is reported using ball milling. Controlled amount of PVP was mixed in the solvent to stabilize the Zn particles and minimize cold welding during milling. The size of the produced Zn …

Structural, Dielectric, And Ferroelectric Characterization Of Lead-Free Calcium-Cerium Co-Doped Batio3 Ceramics, Juan Alberto Duran

Open Access Theses & Dissertations

Structure, morphology, and regulation of the dielectric properties via close-composition intervals is demonstrated for variable-cerium, constant-calcium co-doped barium titanate (Ba0.80Ca0.20CeyTi1-yO3; y=0.0-0.25; referred to BCCT). The effect of variable Ce-content on the structure and dielectric properties of BCCT is investigated. X-ray diffraction spectra confirms the studied samples are mainly in BT tetragonal phase with a small secondary phase detected as CaTiO3 in BCCT for y = 0.20 and 0.25. However, the lattice parameter reduction was evident with increasing Ce-content. Composition-driven dielectric constant leap (4,000-5,500) was observed from intrinsic BCT to BCCT for (y = 0.0-0.04). The temperature dependent dielectric constant showed …

Electrocatalysis In Li-S Batteries, Hesham I. Al Salem

Wayne State University Dissertations

Stabilizing polysulfide-shuttle process while ensuring high sulfur loading holds the key to realize high theoretical energy density (2500 Wh/kg) of lithium-sulfur (Li-S) batteries. Though several carbon based porous materials have been used as host structures for sulfur and its intermediate polysulfides, the week adsorption of polysulfides on carbon surface and its poor reaction kinetics limits them from practical application. Here, we preset a novel ‘electcatalysis’ approach to stabilize polysulfide shuttle process and also enhance its red-ox kinetics. As a proof of concept, we have studied in-detail using conventional electrocatalyst i.e Pt/graphene composite, further the same extended to cost-effective electrocatalysts such …

Biomimetic Substrate Control Of Cellular Mechanotransduction, Mohammad Nahid Andalib, Yuris A. Dzenis, Henry J. Donahue, Jung Yul Lim

Department of Mechanical and Materials Engineering: Faculty Publications

Extracellular mechanophysical signals from both static substrate cue and dynamic mechanical loading have strong potential to regulate cell functions. Most of the studies have adopted either static or dynamic cue and shown that each cue can regulate cell adhesion, spreading, migration, proliferation, lineage commitment, and differentiation. However, there is limited information on the integrative control of cell functions by the static and dynamic mechanophysical signals. For example, a majority of dynamic loading studies have tested mechanical stimulation of cells utilizing cultures on flat surfaces without any surface modification. While these approaches have provided significant information on cell mechanotransduction, obtained outcomes …

Characterizing The Boundary Lateral To The Shear Direction Of Deformation Twins In Magnesium, Y. Liu, N. Li, S. Shao, M. Gong, J Wang, R.J. Mccabe, Y. Jiang, C.N. Tome

Department of Mechanical and Materials Engineering: Faculty Publications

The three-dimensional nature of twins, especially the atomic structures and motion mechanisms of the boundary lateral to the shear direction of the twin, has never been characterized at the atomic level, because such boundary is, in principle, crystallographically unobservable.We thus refer to it here as the dark side of the twin. Here, using high-resolution transmission electron microscopy and atomistic simulations, we characterize the dark side of {1012} deformation twins in magnesium. It is found that the dark side is serrated and comprised of {1012} coherent twin boundaries and semi-coherent twist prismatic–prismatic {2110} boundaries that control twin growth. The conclusions of …

Stress-Dependent Ultrasonic Scattering In Polycrystalline Materials, Christopher M. Kube, Christopher A Turner

Department of Mechanical and Materials Engineering: Faculty Publications

Stress-dependent elastic moduli of polycrystalline materials are used in a statistically based model for the scattering of ultrasonic waves from randomly oriented grains that are members of a stressed polycrystal. The stress is assumed to be homogeneous and can be either residual or generated from external loads. The stress-dependent elastic properties are incorporated into the definition of the differential scattering cross-section, which defines how strongly an incident wave is scattered into various directions. Nine stress-dependent differential scattering cross-sections or scattering coefficients are defined to include all possibilities of incident and scattered waves, which can be either longitudinal or (two) transverse …

Graphene Platform For Neural Regenerative Medicine, Tasneem Bouzid, Alexander Sinitskii, Jung Yul Lim

Department of Mechanical and Materials Engineering: Faculty Publications

Graphene is a material composed of a single layer of carbon atoms arranged in a two-dimensional honeycomb lattice. The unique electrical, optical, thermal, and mechanical properties of graphene are extensively exploited for various applications in electronics, energy, and sensors. Studies also proposed the potential of graphene for biomedical applications. The intrinsic characteristics of graphene and its availability for chemical and physical modifications make graphene a promising vehicle for various biomedical applications including drug delivery, bioimaging, disease diagnostics, etc. The chemical structure of graphene and, in turn, its functionality, can be altered by attaching functional groups, which not only modify the …

Mode-Converted Ultrasonic Scattering In Polycrystals With Elongated Grains, Andrea P. Arguelles, Christopher M. Kube, Ping Hu, Joseph A. Turner

Department of Mechanical and Materials Engineering: Faculty Publications

Elastic wave scattering is used to study polycrystalline media for a wide range of applications. Received signals, which include scattering from the randomly oriented grains comprising the polycrystal, contain information from which useful microstructural parameters may often be inferred. Recently, a mode-converted diffuse ultrasonic scattering model was developed for evaluating the scattered response of a transverse wave from an incident longitudinal wave in a polycrystalline medium containing equiaxed single-phase grains with cubic elastic symmetry. In this article, that theoretical mode-converted scattering model is modified to account for grain elongation within the sample. The model shows the dependence on scattering angle …