Nanoscience and Nanotechnology Commons^™

Multiple Consecutive Recapture Of Rigid Nanoparticles Using A Solid-State Nanopore Sensor, Jungsoo Lee

Mechanical Engineering Research Theses and Dissertations

Solid‐state nanopore sensors have been used to measure the size of a nanoparticle by applying a resistive pulse sensing technique. Previously, the size distribution of the population pool could be investigated utilizing data from a single translocation, however, the accuracy of the distribution is limited due to the lack of repeated data. In this study, we characterized polystyrene nanobeads utilizing single particle recapture techniques, which provide a better statistical estimate of the size distribution than that of single sampling techniques. The pulses and translocation times of two different sized nanobeads (80 nm and 125 nm in diameter) were acquired repeatedly …

Method For Single Crystal Growth Of Photovoltaic Perovskite Material And Devices, Jinsong Huang, Qingfeng Dong

Department of Mechanical and Materials Engineering: Faculty Publications

Systems and methods for perovskite single crystal growth include using a low temperature solution process that employs a temperature gradient in a perovskite solution in a container , also including at least one small perovskite single crystal , and a substrate in the solution upon which substrate a perovskite crystal nucleates and grows , in part due to the temperature gradient in the solution and in part due to a temperature gradient in the substrate . For example , a top portion of the substrate external to the solution may be cooled .

Oct-Based Three Dimensional Modeling Of Stent Deployment, Pengfei Dong, David Prabhu, David L. Wilson, Hiram G. Bezerra, Linxia Gu

Department of Mechanical and Materials Engineering: Faculty Publications

Stent deployment has been widely used to treat narrowed coronary artery. Its acute outcome in terms of stent under expansion and malapposition depends on the extent and shape of calcifications. However, no clear understanding as to how to quantify or categorize the impact of calcification. We have conducted ex vivo stenting characterized by the optical coherence tomography (OCT). The goal of this work is to capture the ex vivo stent deployment and quantify the effect of calcium morphology on the stenting. A three dimensional model of calcified plaque was reconstructed from ex vivo OCT images. The crimping, balloon expansion and …

Rapid Characterization Of Local Shape Memory Properties Through Indentation, Peizhen Li, Haluk E. Karaca, Yang-Tse Cheng

Mechanical Engineering Faculty Publications

Shape memory alloys (SMAs) have the ability to show large recoverable shape changes upon temperature, stress or magnetic field cycling. Their shape memory, material and magnetic properties (e.g. transformation temperatures, strain, saturation magnetization and strength) determine their prospects for applications from small-scale microelectromechanical systems to large scale aerospace and biomedical systems. It should be noted that properties of SMAs are highly temperature dependent. Generally, the conventional mechanical characterization methods (e.g, tension, compression, and torsion) are used on bulk samples of SMAs to determine those properties. In this article, it will be shown that indentation technique can be used as an …

Floating-Gate Transistor Photodetector, Jinsong Huang, Yongbo Yuan

Department of Mechanical and Materials Engineering: Faculty Publications

A field effect transistor photodetector that can operate in room temperature includes a source electrode , a drain electrode , a channel to allow an electric current to flow between the drain and source electrodes , and a gate electrode to receive a bias voltage for controlling the current in the channel . The photodetector includes a light - absorbing mate rial that absorbs light and traps electric charges . The light absorbing material is configured to generate one or more charges upon absorbing light having a wavelength within a specified range and to hold the one or more charges …

Software For Extracting Deformation Gradient And Stress From Md Simulations: Simulations Using The Charmm Force Field, Mehrdad Negahban, Lili Zhang, Zesheng Zhang, John Jasa, Antoine Jérusalem

Department of Mechanical and Materials Engineering: Faculty Publications

Software was developed, and is provided under a general use license, to calculate continuum level deformation gradient and stress for any group of atoms in an MD simulation that uses the Charmm force fields. This software can also calculate the interaction stress applied by one group of atoms on any other group. To obtain deformation gradient and stress, the user needs to provide the selected group(s) of atoms in an atom group identification file, and provide the associated LAMMPS format files and force field parameter file. An example is included to demonstrate the use of the software.

Energy Absorbing Guardrail System, John R. Rohde, John D. Reid, King K. Mak, Dean L. Sicking

Department of Mechanical and Materials Engineering: Faculty Publications

A highway crash attenuation system having W - beam rail elements attached to a plurality of vertical posts . An impact terminal with a feeder chute guides one or more of the W - beam rail elements through the impact terminal . The feeder chute has an impact shield extending along a traffic facing side of the chute from an upstream - most end to a downstream - most end of the chute closing the traffic - facing side of the chute . The system also has an anchor cable release mechanism for releasing the cable downstream of the first …

Shape-Adaptive Mechanism For Robotic Grasping, Carl A. Nelson

Department of Mechanical and Materials Engineering: Faculty Publications

A grapser can include a first pantograph cell and a second pantograph cell coupled with the first pantogrpah cell. The first and second pantograph cells can be coupled together at a first pivot and a second pivot. The grasper can also include a finger extendable in a direction extending between the first pivot and the second pivot. The grasper can include a support base, where one or more links of the first pantograph cell can be slidably coupled with the support base for extending the grasper. In some embodiment, the grasper can be configured to extend along a curved path. …

Spectral Phonon Relaxation Time Calculation Tool Based On Molecular Dynamics, Divya Chalise, Tianli Feng, Xiulin Ruan

The Summer Undergraduate Research Fellowship (SURF) Symposium

Thermal conductivity is an important material property which affects the performance of a wide range of devices from thermoelectrics to nanoelectronics. Information about phonon vibration modes and phonon relaxation time gives significant insight into understanding and engineering material’s thermal conductivity. Although different theoretical models have been developed for studying phonon modes and relaxation time, extensive knowledge of lattice dynamics and molecular dynamics is required to compute phonon modal frequencies and relaxation times. Therefore, a computational tool which can take simple inputs to calculate phonon mode frequencies and relaxation time will be beneficial. Through this research work, such computational tool has …

Modal Phonon Transport Across Interfaces By Non-Equilibrium Molecular Dynamics Simulation, Yang Zhong, Tianli Feng, Xiulin Ruan

The Summer Undergraduate Research Fellowship (SURF) Symposium

Phonons represent the quantization of lattice vibration, responsible for heat transfer in semiconductors and dielectrics. Phonon heat conduction across interfaces is crucially important for the thermal management of real-life devices such as smartphones, electric vehicles, and satellites. Although recent studies have broadly investigated spectral phonon contribution to lattice thermal conductivity, the mechanism of phonon modal transport across interfaces is still not well-understood. Previous models, including the acoustic mismatch model (AMM) and diffuse mismatch model (DMM), only consider elastic process while neglecting inelastic phonon contributions. Herein, we employ spectral Non-Equilibrium Molecular Dynamics Simulation (NEMD) to probe the temperature and heat flux …

Deformation Behavior Of Al/A-Si Core-Shell Nanostructures, Robert Andrew Fleming

Graduate Theses and Dissertations

Al/a-Si core-shell nanostructures (CSNs), consisting of a hemispherical Al core surrounded by a hard shell of a-Si, have been shown to display unusual mechanical behavior in response to compression loading. Most notably, these nanostructures exhibit substantial deformation recovery, even when loaded much beyond the elastic limit. Nanoindentation measurements revealed a unique mechanical response characterized by discontinuous signatures in the load-displacement data. In conjunction with the indentation signatures, nearly complete deformation recovery is observed. This behavior is attributed to dislocation nucleation and annihilation events enabled by the 3-dimensional confinement of the Al core. As the core confinement is reduced, either through …

Meniscus-Assisted Solution Printing Of Largegrained Perovskite Films For High-Efficiency Solar Cells, Ming He, Bo Li, Xun Cui, Beibei Jiang, Yanjie He, Yihuang Chen, Daniel O'Neil, Paul Szymanski, Mostafa A. El-Sayed, Jinsong Huang, Zhiqun Lin

Department of Mechanical and Materials Engineering: Faculty Publications

Control over morphology and crystallinity of metal halide perovskite films is of key importance to enable high-performance optoelectronics. However, this remains particularly challenging for solution-printed devices due to the complex crystallization kinetics of semiconductor materials within dynamic flow of inks. Here we report a simple yet effective meniscus-assisted solution printing (MASP) strategy to yield large-grained dense perovskite film with good crystallization and preferred orientation. Intriguingly, the outward convective flow triggered by fast solvent evaporation at the edge of the meniscus ink imparts the transport of perovskite solutes, thus facilitating the growth of micrometre-scale perovskite grains. The growth kinetics of perovskite …

Dissipative Elastic Metamaterial With A Lowfrequency Passband, Yongquan Liu, Jianlin Yi, Zheng Li, Xianyue Su, Wenlong Li, Mehrdad Negahban

Department of Mechanical and Materials Engineering: Faculty Publications

We design and experimentally demonstrate a dissipative elastic metamaterial structure that functions as a bandpass filter with a low-frequency passband. The mechanism of dissipation in this structure is well described by a mass-spring-damper model that reveals that the imaginary part of the wavenumber is non-zero, even in the passband of dissipative metamaterials. This indicates that transmittance in this range can be low. A prototype for this viscoelastic metamaterial model is fabricated by 3D printing techniques using soft and hard acrylics as constituent materials. The transmittance of the printed metamaterial is measured and shows good agreement with theoretical predictions, demonstrating its …

Multiple Scattering Theory For Heterogeneous Elastic Continua With Strong Property Fluctuation: Theoretical Fundamentals And Applications, Huijing He

Department of Mechanical and Materials Engineering: Faculty Publications

Scattering of elastic waves in heterogeneous media has become one of the most important problems in the field of wave propagation due to its broad applications in seismology, natural resource exploration, ultrasonic nondestructive evaluation and biomedical ultrasound. Nevertheless, it is one of the most challenging problems because of the complicated medium inhomogeneity and the complexity of the elastodynamic equations. A widely accepted model for the propagation and scattering of elastic waves, which properly incorporates the multiple scattering phenomenon and the statistical information of the inhomogeneities is still missing. In this work, the author developed a multiple scattering model for heterogeneous …

A Strategy To Optimize Recovery In Orthopedic Sports Injuries, Michael P. Sealy, Ziye Liu, Chao Li, Yuebin Guo, Ben White, Mark Barkey, Brian Jordon J, Luke N. Brewer, Dale Feldman

Department of Mechanical and Materials Engineering: Faculty Publications

An important goal for treatment of sports injuries is to have as short a recovery time as possible. The critical problem with current orthopedic implants is that they are designed to be permanent and have a high complication rate (15%) that often requires removal and replacement with a second surgery; and subsequently a second rehabilitation cycle. This study was designed to test the feasibility of having a device that could provide the needed mechanical properties, while promoting healing, for a specified amount of time and then degrade away, to shorten the recovery time. The specific strategy was to create a …

Enhanced Visible Light Photocatalytic Remediation Of Organics In Water Using Zinc Oxide And Titanium Oxide Nanostructures, Srikanth Gunti

USF Tampa Graduate Theses and Dissertations

The techniques mostly used to decontaminate air as well as water pollutants have drawbacks in terms of higher costs, require secondary treatment, and some methods are very slow. So, emphasis has been given to water though the use of photocatalysts, which break organic pollutants to water and carbon dioxide and leave no trace of by-products at the end. Photocatalytic remediation aligns with the waste and wastewater industries’ zero waste schemes with lower cost, eco-friendly and sustainable treatment technology. The commonly used photocatalysts such as titanium oxide (TiO₂), zinc oxide (ZnO), tungsten oxide (WO₃) have band gap …

Optimization Of Reduced Graphene Oxide Deposition For Hydrogen Sensing Technologies, Matthew Pocta

Mechanical Engineering Undergraduate Honors Theses

Graphene is known to be a key material for improving the performance of hydrogen sensors. High electrical conductivity, maximum possible surface area with respect to volume, and high carrier mobility are a few of the properties that make graphene ideal for hydrogen sensing applications. The problem with utilizing graphene is the difficulty in depositing uniform, thin layers onto substrate surfaces. This study examines a new method of optimizing graphene deposition by utilizing an airbrush to deposit both graphene oxide (GO) and reduced graphene oxide (rGO) onto glass substrates. The number of depositions were varied among samples to study the effect …

Fabrication And Study Of The Structure And Magnetism Of Rare-Earth Free Nanoclusters, Bhaskar Das

Department of Physics and Astronomy: Dissertations, Theses, and Student Research

No abstract provided.

Method And Shear-Driven Micro-Fluidic Pump, Nihad E. Daidzic

Aviation Department Publications

United States Patent Application, Publication Number US 2017/0096990 A1, Publication Date April 6, 2017.

An example includes an apparatus to pump a fluid. The apparatus includes a housing extending along a length defining an elongate interior, an actuator in the housing, conforming to the elongate interior, the actuator including a plurality of lumens, each having a length extending substantially parallel to the elongate interior, each from around 10 to 200 micrometers across and an actuator configured to oscillate the actuator in the actuator housing along the length of the elongate interior with a rate differential between movement in a first …

Primary Blast Waves Induced Brain Dynamics Influenced By Head Orientations, Yi Hua, Yugang Wang, Linxia Gu

Department of Mechanical and Materials Engineering: Faculty Publications

There is controversy regarding the directional dependence of head responses subjected to blast loading. The goal of this work is to characterize the role of head orientation in the mechanics of blast wave-head interactions as well as the load transmitting to the brain. A three-dimensional human head model with anatomical details was reconstructed from computed tomography images. Three different head orientations with respect to the oncoming blast wave, i.e., front-on with head facing blast, back-on with head facing away from blast, and side-on with right side exposed to blast, were considered. The reflected pressure at the blast wave-head interface positively …

Intracellular Nanoparticle Dynamics Affected By Cytoskeletal Integrity, Martha E. Grady, Emmabeth Parrish, Matthew A. Caporizzo, Sarah C. Seeger, Russell J. Composto, David M. Eckmann

Mechanical Engineering Faculty Publications

The cell interior is a crowded chemical space, which limits the diffusion of molecules and organelles within the cytoplasm, affecting the rates of chemical reactions. We provide insight into the relationship between non-specific intracellular diffusion and cytoskeletal integrity. Quantum dots entered the cell through microinjection and their spatial coordinates were captured by tracking their fluorescence signature as they diffused within the cell cytoplasm. Particle tracking revealed significant enhancement in the mobility of biocompatible quantum dots within fibrosarcoma cells versus their healthy counterparts, fibroblasts, as well as in actin destabilized fibroblasts versus untreated fibroblasts. Analyzing the displacement distributions provided insight into …

Formation Of Mound-Like Multiscale Surface Structures On Titanium By Femtosecond Laser Processing, Edwin Peng, Alfred Tsubaki, Craig A. Zuhlke, Ryan Bell, Meiyu Wang, Dennis R. Alexander, George Gogos, Jeffrey E. Shield

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Surface Functionalization Technique • Femtosecond Laser Surface Processing (FLSP) • Utilize high power, femtosecond (10-15 s) laser pulses • Produce self-organized, multiscale surface micro/nanostructures • Diverse range of applicable substrates: semiconductors, metals, polymers, & composites

Why? • What are the different types of FLSP structures on Ti? • Physical evidence needed for FLSP formation models • Optimize FLSP of Ti for biomedical & other applications

How? • Obtain evidence of mound growth processes by examining underlying microstructure • Utilize dual beam Scanning Electron Microscope-Focused Ion Beam instrument to cross section surface structures & fabricate transmission electron microscopy samples

Dirichlet Process Gaussian Mixture Models For Real-Time Monitoring And Their Application To Chemical Mechanical Planarization, Jia (Peter) Liu, Omer F. Beyca, Prahalad K. Rao, Zhenyu (James) Kong, Satish T. S. Bukkapatnam

Department of Mechanical and Materials Engineering: Faculty Publications

The goal of this work is to use sensor data for online detection and identification of process anomalies (faults). In pursuit of this goal, we propose Dirichlet process Gaussian mixture (DPGM) models. The proposed DPGM models have two novel outcomes: 1) DP-based statistical process control (SPC) chart for anomaly detection and 2) unsupervised recurrent hierarchical DP clustering model for identification of specific process anomalies. The presented DPGM models are validated using numerical simulation studies as well as wireless vibration signals acquired from an experimental semiconductor chemical mechanical planarization (CMP) test bed. Through these numerically simulated and experimental sensor data, we …

Strained Hybrid Perovskite Thin Films And Their Impact On The Intrinsic Stability Of Perovskite Solar Cells, Jingjing Zhao, Yehao Deng, Haotong Wei, Xiaopeng Zheng, Zhenhua Yu, Yuchuan Shao, Jeffrey E. Shield, Jinsong Huang

Department of Mechanical and Materials Engineering: Faculty Publications

Organic-inorganic hybrid perovskite (OIHP) solar cells have achieved comparable efficiencies to those of commercial solar cells, although their instability hinders their commercialization. Although encapsulation techniques have been developed to protect OIHP solar cells from external stimuli such as moisture, oxygen, and ultraviolet light, understanding of the origin of the intrinsic instability of perovskite films is needed to improve their stability. We show that the OIHP films fabricated by existing methods are strained and that strain is caused by mismatched thermal expansion of perovskite films and substrates during the thermal annealing process. The polycrystalline films have compressive strain in the out-of-plane …

The Effect Of Number Of Corrugation On Crashworthiness Of Aluminum Corrugated Tube Under Lateral Loading, Hozhabr Mozafari, Arameh Eyvazian, Abdel Magid Hamouda

Department of Mechanical and Materials Engineering: Faculty Publications

Thin-walled tubes have been developed and are growing in use as new energy absorber structures. The objective of this study is to investigate the energy absorption and crushing characteristics of corrugated tubes with different number of corrugation in a specific length exposed to lateral loading. At the first step, experimental tests were carried out on a corrugated tube with three con'ugations (two inner and one outer) and a tube without corrugation. After that, a finite element model was developed by means of ABAQUS software in order to study the effect of corrugation number on crushing properties of thin-walled tubes. The …

Methods, Systems, And Devices For Surgical Visualization And Device Manipulation, Shane M. Farritor, Mark Rentschler, Amy Lehman, Nathan A. Wood, Adam Bock, Reed Prior

Department of Mechanical and Materials Engineering: Faculty Publications

A surgical device includes a console having a visual display and a manipulator arm, a robotic device having a camera and a connection component. The robotic device is configured to be positioned completely within a body cavity. The camera is configured to transmit visual images to the visual display. The connection component operably couples the console and the robotic device. The manipulator arm is positioned relative to the visual display so as to appear to be penetrating the visual display.

Local And Segmental Motions Of The Mobile Amorphous Fraction In Semi-Crystalline Polylactide Crystallized Under Quiescent And Flow-Induced Conditions, Xavier Monnier, Laurence Chevalier, Antonello Esposito, Lucia Fernandez-Ballester, Allisson Saiter, Eric Dargent

Department of Mechanical and Materials Engineering: Faculty Publications

The molecular dynamics of the constrained and unconstrained mobile amorphous fractions in semicrystalline polylactide (PLA) was investigated in the presence of both flow-induced crystalline structures and spherulites by fast scanning calorimetry (FSC) through cooperativity and physical aging concepts. First, the shear rate conditions leading to flow-induced crystallization were characterized by examining the relaxation of shear-induced precursors. At a temperature of 150 °C, the critical relaxation time is so long that cooling down the sheared melt to the crystallization temperature does not affect significantly the precursors. Therefore, highly oriented structures develop. The arrangement of the crystalline fraction, either in flow-induced crystalline …

Experimental Study Of Corrugated Metal-Composite Tubes Under Axial Loading, Arameh Eyvazian, Hozhabr Mozafari, Abdel Magid Hamouda

Department of Mechanical and Materials Engineering: Faculty Publications

In this study, crushing behavior of corrugated metal-composite tube was examined experimentally under axial loading condition. Six types of specimens, classified into two groups of metal and metal-composite, were tested under quasi static axial loading. The failure mechanism and failure history of the specimens were presented and discussed. The experimental result showed that corrugated metal composite tubes demonstrate perfect energy absorption characteristics in terms of uniformity of load-displacement diagram, reduction of initial peak load and controlling failure mechanism. Moreover, it was also found that adding filament wound layer of composite on the surface of metallic corrugated tube compensated weakness of …

Disturbed Cyclical Stretch Of Endothelial Cells Promotes Nuclear Expression Of The Pro-Atherogenic Transcription Factor Nf-Kb, Ryan M. Pedrigi, Konstantinos I. Papadimitriou, Avinash Kondiboyina, Sukhjinder Sidhu, James Chau, Miten B. Patel, Daniel C. Baeriswyl, Emmanuel M. Drakakis, Rob Krams

Department of Mechanical and Materials Engineering: Faculty Publications

Exposure of endothelial cells to low and multidirectional blood flow is known to promote a pro-atherogenic phenotype. The mechanics of the vessel wall is another important mechano-stimulus within the endothelial cell environment, but no study has examined whether changes in the magnitude and direction of cell stretch can be pro-atherogenic. Herein, we developed a custom cell stretching device to replicate the in vivo stretch environment of the endothelial cell and examined whether low and multidirectional stretch promote nuclear translocation of NF-kB. A fluid–structure interaction model of the device demonstrated a nearly uniform strain within the region of cell attachment and …

Quantification Of Re-Absorption And Re-Emission Processes To Determine Photon Recycling Efficiency In Perovskite Single Crystals, Yanjun Fang, Haotong Wei, Qingfeng Dong, Jinsong Huang

Department of Mechanical and Materials Engineering: Faculty Publications

Photon recycling, that is, iterative self-absorption and re-emission by the photoactive layer itself, has been speculated to contribute to the high open-circuit voltage in several types of high efficiency solar cells. For organic–inorganic halide perovskites that have yielded highly efficient photovoltaic devices, however, it remains unclear whether the photon recycling effect is significant enough to improve solar cell efficiency. Here we quantitatively evaluate the re-absorption and re-emission processes to determine photon recycling efficiency in hybrid perovskite with its single crystals by measuring the ratio of the re-emitted photons to the initially excited photons, which is realized by modulating their polarization …