Nanoscience and Nanotechnology Commons^™

An Investigation Of Testing Parameters On The Frictional Properties Of Patterned Core-Shell Nanostructures, Colin Phelan

Graduate Theses and Dissertations

Friction tests are a beneficial means to analyze the tribological characteristics and advantages of materials and textured surfaces. However, the selected test parameters can significantly influence the results. This work explores the significance of the friction testing parameters on the frictional performances of core-shell nanostructure-textured surfaces (CSNTSs). Several applied normal loads (10 μN, 100 μN, and 500 μN) and diamond counterface indenter tip radii (1 μm, 5 μm, and 20 μm) were selected for the testing of Al/diamond-like-carbon (DLC) and Al/amorphous silicon (a-Si) CSNTSs. The measured friction values of the CSNTSs were then compared to a matching Al/DLC film and …

Development Of A Laser-Assisted Chemical Vapor Deposition (Cvd) Technique To Grow Carbon-Based Materials, Abiodun Ademola Odusanya

Graduate Theses/Dissertations

Carbon-based materials (CBMs) including graphene, carbon nanotubes (CNT), highly ordered pyrolytic graphite (HOPG), and pyrolytic carbon (PyC) have gained so much attention in research in recent years because of their unique electronic, optical, thermal, and mechanical properties. CBMs are relatively very stable and have minimal environmental footprint. Various techniques such as mechanical exfoliation, pulsed laser deposition, and chemical vapor deposition (CVD) have been used to grow CBMs and among them thermal CVD is the most common. This study aims to explore ways of reducing the energy requirement to produce CBMs, and for that, a novel pulsed laser-assisted CVD technique had …

Peptoid-Functionalized Gold Nanoparticles For Zika Virus Envelope Protein Detection, Meagan Olsen

Chemical Engineering Undergraduate Honors Theses

Detection and identification of viral pathogens is essential in providing effective and rapid medical treatment. Well-established detection methods can be expensive, slow, and sometimes unable to provide the needed sensitivity and specificity. The Zika virus is one clinically relevant pathogen that cannot be easily identified due to cross-reactivity with other viruses from the same family. Electrochemical sensors enhanced with peptoid-functionalized gold nanoparticles (AuNPs) are an alternative to traditional techniques that offers rapid, accurate, label-free pathogen detection for point-of-care diagnostics. To this end, a peptoid capable of binding to the Zika virus envelope protein was developed and its binding affinity for …

Oxone® Mediated Tempo-Oxidized Cellulose Nanomaterials: Material Characterization, Ultrafiltration Membrane Separations, And Thin Film Composite Gas Transport Analysis, John Phillips Moore

Graduate Theses and Dissertations

Cellulose nanomaterials (CNMs) are derived from plant matter and are comprised of nanoscopic cellulose crystals and fibers. They have a diverse set of applications, from cosmetics to oil recovery. This study focuses on the properties of Oxone® mediated TEMPO-oxidized cellulose nanomaterials (OTO-CNMs) and their use in controlling the transport properties of polymeric substrates. Synthesis and characterization of cellulosic nanoparticles have resulted in the creation of OTO-CNMs with properties that increase hydrophilicity. With added hydrophilicity, OTO-CNMs possess lower fouling propensity, making them ideal membrane additive for transport limited separations such as hemodialysis.

To utilize the material and unique properties thereof, this …

Photothermal Response Induced By Nanocage-Coated Artificial Extracellular Matrix Promotes Neural Stem Cell Differentiation, Seunghyun Jung, Nathaniel Harris, Isabelle I. Niyonshuti, Samir V. Jenkins, Abdallah M. Hayar, Fumiya Watanabe, Azemat Jamshidi-Parsian, Jingyi Chen, Michael J. Borrelli, Robert J. Griffin

Mechanical Engineering Faculty Publications and Presentations

Strategies to increase the proportion of neural stem cells that differentiate into neurons are vital for therapy of neurodegenerative disorders. In vitro, the extracellular matrix composition and topography have been found to be important factors in stem cell differentiation. We have developed a novel artificial extracellular matrix (aECM) formed by attaching gold nanocages (AuNCs) to glass coverslips. After culturing rat neural stem cells (rNSCs) on these gold nanocage-coated surfaces (AuNC-aECMs), we observed that 44.6% of rNSCs differentiated into neurons compared to only 27.9% for cells grown on laminin-coated glass coverslips. We applied laser irradiation to the AuNC-aECMs to introduce precise …

Tensile-Strained Germanium Quantum Dots Grown On Indium Aluminum Arsenide (111)A And (110) By Molecular Beam Epitaxy, Kathryn Eva Sautter

Boise State University Theses and Dissertations

Molecular beam epitaxy (MBE) enables the growth of semiconductor nanostructures known as tensile-strained quantum dots (TSQDs). The highly tunable nature of TSQD properties means that they are of interest for a wide variety of applications including for infrared (IR) lasers and light-emitting diodes (LEDs), improved tunnel junction efficiency in multijunction solar cell technology, quantum key encryption, and entangled photon emission. In this project, I focus on one of the most technologically important materials, germanium (Ge). Ge has a high gain coefficient, high electron mobility, and low band gap: all excellent properties for optoelectronic applications. Until recently, these technological advantages were …

Characterization Of Protein Aggregation Using A Solid-State Nanopore Device, Mitu Chandra Acharjee

Graduate Theses and Dissertations

Protein aggregation has been linked to many chronic and devastating neurodegenerative human diseases and is also strongly associated with aging. In the case of neurodegenerative diseases, α, β tubulins and tau proteins dissociate in a neuron cell and aggregate both intra and extra-cellularly. Tau and tubulin aggregations were found as one of the major causes of many neurodegenerative diseases, such as Parkinson’s, Picks, Alzheimer’s, Huntington, and Prion. Finding the state and mechanism of protein aggregation is significant. In this work, tau and tubulin aggregations were detected in ionic solutions using the solid-state nanopore technique. Besides tau and tubulin, aggregations of …

Application Of Atomically Precise Metal Nanoclusters In Electrocatalysis, Zhi-Hua Zhuang, Wei Chen

Journal of Electrochemistry

Metal nanoclusters (M NCs) consist of only several to a few hundred of metal atoms and possess core sizes less than 2 nm. Owing to the quantum size effect, the electronic states of M NCs evolve to discrete levels similar to the molecule energy gaps, other than a continuous density of states to produce plasmon characteristic of bulk metal nanoparticles (M NPs). In comparison with the conventional M NPs, M NCs exhibit dramatically unique electronic and optical properties, such as molecule-like energy gaps, strong photoluminescence and high catalytic properties, which make them promising for potential application in numerous fields, such …

Electrochemiluminescence Imaging Hydrogen Evolution Reaction On Single Platinum Nanoparticles Using A Bipolar Nanoelectrode Array, Xiang Qin, Zhong-Qiu Li, Jian-Bin Pan, Jian Li, Kang Wang, Xing-Hua Xia

Journal of Electrochemistry

A high-density (5.7 × 10⁸ cm^-2) nanoelectrode array with the electrode diameter of 200 nm and the interelectrode distance of 450 nm were fabricated. The nanoelectrode array consisted of gold nanowires embedded in a porous anodic aluminum oxide (AAO) matrix, having regular nanoelectrode distribution and highly uniform nanoelectrode size. The gold nanoelectrode array was used as a closed bipolar nanoelectrode array combined with electrochemiluminescence (ECL) method to map the electrocatalytic activity of platinum nanoparticles toward hydrogen evolution reaction (HER) by modifying the catalysts on single nanoelectrodes. Results show that HER on single bipolar nanoelectrodes could be imaged …

Electrochemical Surface-Enhanced Raman Spectroscopic Studies On Nickel Ultramicroelectrode, Li-Wen Wu, Wei Wang, Yi-Fan Huang

Journal of Electrochemistry

Nickel (Ni) electrodes are widely used in electrochemical researches. Understanding electrochemical processes on Ni electrodes through in-situ characterization of adsorbed species on their surfaces is helpful for rational optimization and application of Ni electrochemistry. Microelectrochemical surface-enhanced Raman spectroscopy (μEC-SERS) combines the mass transfer feature of ultramicroelectrode with high-sensitivity characterizations of molecular structures, which is a powerful method for studying Ni electrochemistry on polarization and non-equilibrium conditions. The key point of performing μEC-SERS is to make a SERS-active Ni ultramicroelectrode.
Here, we demonstrate a method of preparing a SERS-active Ni ultramicroelectrode through electrochemical deposition of several atomic layers of …

Funtionalization Of Morphologically Different Nanoclays For Enhanced Mechanical Properties, Malachi Kent

Honors College Theses

Nanoclays are microscopic clays that are comprised of layered nanoparticle aluminosilicates that are naturally arranged in several morphologies. Halloysite nanotubes (HNT) are hollow, double-layered tubes, bentonite (BNT) clays are trapezoidal platelets, and nanosilica or silica dioxide (SiO₂) are spherical. These nanoclays were chosen for sustainable purposes as they are naturally derived and for economical purposes because of their cheap commercial availability. In this study, the nanoclays are functionalized with an epoxy organosilane group through reflux conditions at 120 °C for 24 hours. The pristine and functionalized nanoclays were extensively characterized with infrared radiation (IR) spectroscopy, scanning electron microscope …

Solid State Synthesis And Characterization Of Apatite Based Ceramic Waste Form For The Immobilization Of Radioactive Iodine, Md Imdadul Islam

LSU Doctoral Dissertations

The growing demand for nuclear power in the United States and worldwide is accountable for addressing the major concern of radioactive waste, involving the technical challenges of maintaining the nuclear fuel cycle and immobilizing high-level wastes for safe disposal in geological storage. The appropriate selection of waste forms for spent nuclear fuel such as fission products and radionuclides can be effective means for a feasible and sustainable nuclear fuel cycle. But highly volatile radionuclides such as iodine (129) are of specific concern due to its extraordinary long half-life (15.7 million years). Due to its poor solubility and high volatility at …

Nanocellulose Sheets From Oil Palm Empty Fruit Bunches Treated With Naoh Solution, Farah Fahma, Faiza Ayu Lestari, Ika Amalia Kartika, Nurmalisa Lisdayana, Evi Savitri Iriani

Karbala International Journal of Modern Science

The objective of this study is to produce nanocellulose sheets from oil palm empty fruit bunches (OPEFBs). Nanocellulose sheets from OPEFBs were prepared through the dewatering process using vacuum filtration. Subsequently, the produced sheets were treated with NaOH solution to improve the mechanical stability of their structure, causing them to be firm in water. The water absorption of nanocellulose sheet increased with increasing NaOH concentrations up to 20 wt%, increasing tensile strength, and Young’s modulus, but decreased when they were treated with 30 wt%. The diameter shrinkage of nanocellulose sheets was directly proportional to the NaOH concentration and soaking time. …

Preparation Of Pdcoir Tetrahedron Nanocatalysts And Its Performance Toward Ethanol Oxidation Reaction, Zhi-Yuan Yu, Rui Huang, Jie Liu, Guang Li, Qian-Tong Song, Shi-Gang Sun

Journal of Electrochemistry

As a new energy conversion device, direct ethanol fuel cells (DEFCs) are widely concerned because of their remarkable advantages such as high theoretical energy density and wide fuel sources. However, the rapid development of DEFCs has been severely impeded due to the sluggish kinetic process and toxic intermediates especially in their anodic reactions. Palladium (Pd)-based materials are considered to be excellent anode catalysts for DEFCs, especially under alkaline conditions. And further improving their performance is an important direction to promote the development of DEFCs. Surface structure and composition are the key factors affecting the performance of catalysts which can be …

Multifunctional Polydopamine Nanomaterials For Biomedical And Environmental Applications, Hamed Gholami Derami

McKelvey School of Engineering Graduate Student Theses & Dissertations

Polydopamine (PDA), a synthetic and organic material, has emerged as a promising materialplatform for various applications in energy, environmental, and biomedical fields. PDA, formed by self-polymerization of dopamine, is rich in catechol and amine groups, which facilitate covalent conjugation and/or other non-covalent interactions with organic and inorganic materials. It is highly biocompatible, biodegradable, has broadband light absorption spectrum and excellent light-to-heat conversion efficiency. Also, it is easy to synthesize and functionalize. The combination of excellent characteristics of polydopamine-based nanomaterials, make them a promising adsorbent agent for environmental wastewater treatment and photothermal agent for biomedical applications. In the first half of …

Surface Acoustic Waves Increase Magnetic Domain Wall Velocity, Anil Adhikari, Shireen Adenwalla

Shireen Adenwalla Papers

Domain walls in magnetic thin films are being explored for memory applications and the speed at which they move has acquired increasing importance. Magnetic fields and currents have been shown to drive domain walls with speeds exceeding 500 m/s. We investigate another approach to increase domain wall velocities, using high frequency surface acoustic waves to create standing strain waves in a 3 micron wide strip of magnetic film with perpendicular anisotropy. Our measurements, at a resonant frequency of 248.8 MHz, indicate that domain wall velocities increase substantially, even at relatively low applied voltages. Our findings suggest that the strain wave …

Inventions Of Scientists, Engineers And Specialists From Different Countries In The Area Of Nanotechnologies. Part Ii, Leonid A. Ivanov, Li Da Xu, Zhanna V. Pisarenko, Qiang Wang, Petr S. Prokopiev

Information Technology & Decision Sciences Faculty Publications

The article provides an abstract review of patents. The results of creative activity of scientists, engineers and specialists, including inventions in the field of nanotechnology and nanomaterials, being implemented, allow achieving a significant effect in construction, housing and community services, and related sectors of the economy. For example, the invention «Method for liquidphase synthesis of nanostructured ceramic material in the CeO2–Sm2O3 system to create a solid oxide fuel cell» can contribute to the active development of alternative, hydrogen energy. Fuel cells have a wide range of applications – from batteries in portable electronic devices to large-scale power generation and autonomous …

Multi-Level Analysis Of Atomic Layer Deposition Barrier Coatings On Additively Manufactured Plastics For High Vacuum Applications, Nupur Bihari

Dissertations, Master's Theses and Master's Reports

While hardware innovations in micro/nano electronics and photonics are heavily patented, the rise of the open-source movement has significantly shifted focus to the importance of obtaining low-cost, functional and easily modifiable research equipment. This thesis provides a foundation of open source development of equipment to aid in the micro/nano electronics and photonics fields.

First, the massive acceptance of the open source Arduino microcontroller has aided in the development of control systems with a wide variety of uses. Here it is used for the development of an open-source dual axis gimbal system. This system is used to characterize optoelectronic properties of …

Generation Of Excited Species In A Streamer Discharge, Shirshak K. Dhali

Electrical & Computer Engineering Faculty Publications

At or near atmospheric pressure, most transient discharges, particularly in molecular gases or gas mixture containing molecular gases, result in a space charge dominated transport called a streamer discharge. The excited species generation in such discharges forms the basis for plasma chemistry in most technological applications. In this paper, we simulate the propagation of streamers in atmospheric pressure N₂ to understand the energy partitioning in the formation of various excited species and compare the results to a uniform Townsend discharge. The model is fully two-dimensional with azimuthal symmetry. The results show a significantly larger fraction of the energy goes …

Development Of Light Actuated Chemical Delivery Platform On A 2-D Array Of Micropore Structure, Hojjat Rostami Azmand, Hojjat Rostami Azmand

Dissertations and Theses

Localized chemical delivery plays an essential role in the fundamental information transfers within biological systems. Thus, the ability to mimic the natural chemical signal modulation would provide significant contributions to understand the functional signaling pathway of biological cells and develop new prosthetic devices for neurological disorders. In this paper, we demonstrate a light-controlled hydrogel platform that can be used for localized chemical delivery in a high spatial resolution. By utilizing the photothermal behavior of graphene-hydrogel composites confined within micron-sized fluidic channels, patterned light illumination creates the parallel and independent actuation of chemical release in a group of fluidic ports. The …

Detection Of Subsurface, Nanometer-Scale Crystallographic Defects By Nonlinear Light Scattering And Localization, Farbod Shafiei, Tommaso Orzali, Alexey Vert, Mohammad-Ali Miri, Pui Yee Hung, Man Hoi Wong, Andrea Alù, Gennadi Bersuker, Michael C. Downer

Publications and Research

Heteroepitaxial crystalline films underlie many electronic and optical technologies but are prone to forming defects at their heterointerfaces. Atomic-scale defects such as threading dislocations that propagate into a film impede the flow of charge carriers and light degrading electrical/optical performance of devices. Diagnosis of subsurface defects traditionally requires time-consuming invasive techniques such as cross-sectional transmission electron microscopy. Using III–V films grown on Si, noninvasive, bench-top diagnosis of subsurface defects have been demonstrated by optical second-harmonic scanning probe microscope. A high-contrast pattern is observed of subwavelength “hot spots” caused by scattering and localization of fundamental light by defect scattering sites. Size …

Perovskite Thin Films Annealed In Supercritical Fluids For Efficient Solar Cells, Gilbert Annohene

Theses and Dissertations

In the field of photovoltaics, scientists and researchers are working fervently to produce a combination of efficient, stable, low cost and scalable devices. Methylammonium lead trihalide perovskite has attracted intense interest due to its high photovoltaic performance, low cost, and ease of manufacture. Their high absorption coefficient, tunable bandgap, low-temperature processing, and abundant elemental constituent provide innumerable advantages over other thin film absorber materials. Since the perovskite film is the most important in the device, morphology, crystallization, compositional and interface engineering have been explored to boost its performance and stability. High temperatures necessary for crystallization of organic-inorganic hybrid perovskite films …

Continuous Preparation And Application Of Novel Heterogeneous Catalysis, Michael B. Burkholder

Theses and Dissertations

Transition metal heterogeneous catalysts are widely used across many chemical industries to reduce waste and emissions and reduce production time while increasing rate. The prevalence of these materials results from the complex relationship between metal nanoparticles and supports affecting final catalytic performance. Rational catalyst synthesis describes the ability to precisely engineer structures through controlled preparation. Novel materials and continuous processing represent a promising approach for rational catalyst synthesis.

The application of these catalysts in continuous, multiphase processes, such as cross-coupling reactions, oxidation chemistry, and nitroreduction processes, are paramount to developing new commercial routes for high-value products. Pd/G catalysts synthesized by …

In Depth Characterisation Of The Biomolecular Coronas Of Polymer Coated Inorganic Nanoparticles With Differential Centrifugal Sedimentation, André Perez-Potti, Hender Lopez, Beatriz Pelaz, Abuelmagd Abdelmonem, Mahmoud G. Soliman, Ingmar Schoen, Philip M. Kelly, Kenneth A. Dawson, Wolfgang J. Parak, Zeljka Krpetic, Marco P. Monopoli

Articles

Advances in nanofabrication methods have enabled the tailoring of new strategies towards the controlled production of nanoparticles with attractive applications in healthcare. In many cases, their characterisation remains a big challenge, particularly for small-sized functional nanoparticles of 5 nm diameter or smaller, where current particle sizing techniques struggle to provide the required sensitivity and accuracy. There is a clear need for the development of new reliable characterisation approaches for the physico-chemical characterisation of nanoparticles with significant accuracy, particularly for the analysis of the particles in the presence of complex biological fluids. Herein, we show that the Differential Centrifugal Sedimentation can …

Treated Hfo2 Based Rram Devices With Ru, Tan, Tin As Top Electrode For In-Memory Computing Hardware, Yuvraj Dineshkumar Patel

Theses

The scalability and power efficiency of the conventional CMOS technology is steadily coming to a halt due to increasing problems and challenges in fabrication technology. Many non-volatile memory devices have emerged recently to meet the scaling challenges. Memory devices such as RRAMs or ReRAM (Resistive Random-Access Memory) have proved to be a promising candidate for analog in memory computing applications related to inference and learning in artificial intelligence. A RRAM cell has a MIM (Metal insulator metal) structure that exhibits reversible resistive switching on application of positive or negative voltage. But detailed studies on the power consumption, repeatability and retention …

Preparations And Photoelectrochemical Performances Of Rgo-Tio2 Nanotubes Arrays, Ze-Yang Zhang, Lan Sun, Chang-Jian Lin

Journal of Electrochemistry

Decorating TiO₂ nanotube arrays with RGO to improve the photocatalytic activity of TiO₂ nanotube arrays has been reported. For the reported RGO-TiO₂ nanotube arrays, TiO₂ nanotube arrays were prepared by anodizing the high-purity Ti foil in an organic electrolyte for multiple-step treatments, while RGO were deposited on TiO₂ nanotube arrays by using cyclic voltammetry or other electrical reduction methods. To enhance the reduction degree and the coverage of RGO on the resultant RGO-TiO₂ nanotube arrays, in this work, the one-step electrochemical anodization in hydrofluoric acid was used to fabricate TiO₂ nanotube arrays with …

Core-Shell Structured Ru@Ptru Nanoflower Electrocatalysts Toward Alkaline Hydrogen Evolution Reaction, Xue-Liang Wang, Yuan-Yuan Cong, Chen-Xi Qiu, Sheng-Jie Wang, Jia-Qi Qin, Yu-Jiang Song

Journal of Electrochemistry

Water electrolysis for hydrogen production is beneficial for solving the problem of energy crisis and environmental issues. It is necessary to study highly active and cost-effective catalysts toward hydrogen evolution reaction (HER) to reduce the consumption of noble metals. Herein, we report the synthesis of core-shell structured Ru@Pt_0.24Ru nanoflowers electrocatalyst by stepwise reduction of Ru and Pt precursors in the mixture of oleylamine and benzyl alcohol at 160 ^oC. The average diameter of the resultant Ru@Pt_0.24Ru was 16.5±4.0 nm with a bulk atomic ratio between Pt and Ru of 0.24:1 and a surface ratio of …

Interface Engineering Of Materials For Energy And Biological Applications, Ardalan Chaichi

LSU Doctoral Dissertations

Interface interactions are generally classified into solid-liquid, solid-gas, solid-vacuum, liquid-gas, light-matter and electron-matter categories. Surface morphological studies as well as surface chemical reactions can be studied in various types of complex systems thanks to technological advances in materials characterization methods. By employing interface engineering in different applications, it is possible to control electrical, chemical, mechanical, optical and biological properties of materials. Accordingly, we have applied interface engineering in three different areas of energy materials, biomaterials and surface imaging. As a result, firstly, we have introduced a high intensity light flash-based method on engineered substrates for delamination of reduced graphene oxide …

Synthesis Of Novel Coo/Mnfe2o4 Heterostructured Nanoparticles And The Effects Of Variable Size And Extent Of Overgrowth On Their Magnetic Properties, Mohammad Tauhidul Islam

Graduate Theses/Dissertations

A combination of thermal decomposition and surfactant-assisted synthesis route was utilized to synthesize novel CoO/MnFe₂O₄ heterostructured nanoparticles. Four samples of varying CoO core size were synthesized with variable extent of overgrowth phase. XRD, XPS, SEM and TEM data show evidence of MnFe₂O₄ spinel phase overgrowth on CoO rock-salt structured nanoparticles. XPS and magnetic data reveal partial oxidation and formation of Co₃O₄ phase on 7 nm and 19 nm size CoO-based nanoparticles. The remaining samples having 22 nm and 34 nm dimensions show a higher percentage of FiM materials overgrowth on the …

Kinetic Monte Carlo Investigations Involving Atomic Layer Deposition Of Metal-Oxide Thinfilms, David Tyler Magness

Graduate Theses/Dissertations

Atomic Layer Deposition is a method of manufacturing thin film materials. Metal-oxides such as zinc-oxide and aluminum-oxide are particularly interesting candidates for use in microelectronic devices such as tunnel junction barriers, transistors, Schottky diodes, and more. By adopting a 3D Kinetic Monte Carlo model capable of simulating ZnO deposition, the effect of parameters including deposition temperature, chamber pressure, and composition of the initial substrate at the beginning of deposition can be investigated. This code generates two random numbers: One is used to select a chemical reaction to occur from a list of all possible reactions and the second is used …