Nanoscience and Nanotechnology Commons^™

A Titanium-Supported Nanoporous Pd Electrocatalyst For Methanol Oxidation, Feng-Juan Niu, Qing-Feng Yi

Journal of Electrochemistry

Titanium-supported nanoporous palladium electrode(nanoPd /Ti) was prepared by a hydrothermal process in the presence of the ligand EDTA and using formaldehyde as reducing agent.SEM images showed that the size of Pd particles was about 60 nm and the Pd particles were connected with each other to form a three-dimensional network structure.Cyclic voltammetry(CV) and electrochemical impedance spectroscopy(EIS) were applied to evaluate the electrocatalytic activity of the nanoPd/Ti electrode towards methanol oxidation in alkaline solution.CV results showed that the nanoPd /Ti electrode presented high anodic peak densities and a low onset potential for methanol oxidation.Also nanoPd /Ti electrode showed excellent CO tolerance …

Electrocatalytic Oxidation Of Hydrazine At Rutin Carbon Nanotubes Modified Electrode, Hong-Fang Zhang, Qing-Lin Sheng, Jian-Bin Zheng

Journal of Electrochemistry

The electrochemical behavior and electrocatalytic oxidation of hydrazine on rutin multiwall carbon nanotubes modified glassy carbon electrode were studied by cyclic voltammetry.The experimental results indicated that the electrode exhibits good electrocatalytic activity to hydrazine at a reduced oxidation potential of 262 mV.The amperometric response of the modified electrode showed linear increase after successive addition of hydrazine in the concentration range of 2.5×10^-6~1.0×10^-4 mol·L-1 with a detection limit of 5×10^-7 mol·L^-1.

Applications Of Raman Spectroscopy Technique In Lithium Ion Batteries, Liang Zhao, Yong-Sheng Hu, Hong Li, Zhao-Xiang Wang, Hong-Xing Xu, Xue-Jie Huang, Li-Quan Chen

Journal of Electrochemistry

The Raman spectroscopy has been widely used in the study of lithium ion batteries.In this short review,we gave some examples of the applications of Raman spectroscopy in the study of electrode materials including carbonaceous materials,spinel LiM_xMn_2-x O₄,LiFePO₄,as well as polymer electrolytes,room temperaturemolten salt electrolytes and the solid-electrolyte interphase layers.The advantages and disadvantages of the ex-situ and in-situ Raman spectrum techniques are discussed.Using new Raman techniques to investigate Li-ion batteries are suggested.

Simulation Of Electrospun Nanofiber Deposition On Stationary And Moving Substrates, Linhua Liu, Yuris A. Dzenis

Department of Mechanical and Materials Engineering: Faculty Publications

Electrospinning produces continuous fibers with diameters from single nanometers to microns by jetting polymer solutions in high electric fields. Electrospun non-woven filamentary materials attract rapidly growing interest for broad range of applications. Properties of these materials depend on their nano- and microstructure that is determined in turn by the electric field and nanofiber collector. Despite critical importance, deposition of electrospun fibers on substrates has not yet been extensively studied theoretically and new methods of nanofiber collection continue to be developed mostly empirically. The objective of this Letter was to develop and demonstrate numerical simulation of electrospun nanofiber deposition on moving …

Modeling Of Solvent Evaporation From Polymer Jets In Electrospinning, Xiang-Fa Wu, Yury Salkovskiy, Yuris A. Dzenis

Department of Mechanical and Materials Engineering: Faculty Publications

Solvent evaporation plays a critical role in nanofiber formation in electrospinning. Here, we present a nonlinear mass diffusion-transfer model describing the drying process in dilute polymer solution jets. The model is used to predict transient solvent concentration profiles in polyacrylonitrile/ N,N-dimethylformamide (PAN/DMF) jets with the initial radii ranging from 50µm down to 100 nm. Numerical simulations demonstrate high transient inhomogeneity of solvent concentration over the jet cross-section in microscopic jets. The degree of inhomogeneity decreases for finer, submicron jets. The simulated jet drying time decreases rapidly with the decreasing initial jet radius, from seconds for microjets to single milliseconds for …

Preparation And Characterization Of Iron Oxide And Hydroxide Based Nanomaterials, Guillermo Carbajal Franco

Open Access Theses & Dissertations

Iron (Fe) oxides and hydroxides are common and abundant materials. They exhibit diverse crystal structures, properties and phenomena by virtue of which they find a wide range of scientific and technological applications. Controlled growth and manipulation of the specific structure and electronic behavior to meet the requirements of a given application is a challenging problem in view of many possible phases and composition of the resulting materials. The preparation method and experimental conditions will, therefore, significantly affect the properties and performance of Fe oxides and hydroxides. The goal of the project is to obtain Fe-based oxide/hydroxide catalytic materials and to …

Intermediate Layers In Tandem Organic Solar Cells, Yongbo Yuan, Jinsong Huang, Gang Li

Department of Mechanical and Materials Engineering: Faculty Publications

Tandem structures can boost the efficiency of organic solar cell to more than 15%, compared to the 10% limit of single layer bulk heterojunction devices. Design and fabricating of intermediate layers plays a very important role to achieve high device performance. This article will review the main experimental progresses of tandem organic solar cells, and focus on the intermediate layers (charge recombination layers) in both thermal evaporated and solution processed organic tandem solar cell devices.

A Model Of Giant Vacuole Dynamics In Human Schlemm’S Canal Endothelial Cells, Ryan M. Pedrigi, David Simon, Ashley Reed, W. Daniel Stamer, Darryl R. Overby

Department of Mechanical and Materials Engineering: Faculty Publications

Aqueous humour transport across the inner wall endothelium of Schlemm’s canal likely involves flow through giant vacuoles and pores, but the mechanics of how these structures form and how they influence the regulation of intraocular pressure (IOP) are not well understood. In this study, we developed an in vitro model of giant vacuole formation in human Schlemm’s canal endothelial cells (HSCECs) perfused in the basal-to-apical direction (i.e., the direction that flow crosses the inner wall in vivo) under controlled pressure drops (2 or 6 mmHg). The system was mounted on a confocal microscope for time-lapse en face imaging, and cells …

Achieving High Efficiency Laminated Polymer Solar Cell With Interfacial Modified Metallic Electrode And Pressure Induced Crystallization, Yongbo Yuan, Yu Bi, Jinsong Huang

Department of Mechanical and Materials Engineering: Faculty Publications

We report efficient laminated organic photovoltaic device with efficiency approach the optimized device by regular method based on Poly(3-hexylthiophene-2,5-diyl) and [6,6]-phenyl-C₆₁-butyric acid methyl ester (PCBM). The high efficiency is mainly attributed to the formation of a concrete polymer/metal interface mechanically and electrically by the use of electronic-glue, and using the highly conductive and flexible silver film as anode to reduce photovoltage loss and modifying its work function for efficiency hole extraction by ultraviolet/ozone treatment, and the pressure induced crystallization of PCBM.

In Vitro Models For Glaucoma Research: Effects Of Hydrostatic Pressure, Yuan Lei, Shadi Rajabi, Ryan M. Pedrigi, Darryl R. Overby, A. Thomas Read, C. Ross Ethier

Department of Mechanical and Materials Engineering: Faculty Publications

PURPOSE. The response of cells (e.g., optic nerve head [ONH] cells) to mechanical stress is important in glaucoma. Studies have reported the biological effects of hydrostatic pressure on ONH cells cultured on a rigid substrate. An apparatus, designed to independently vary hydrostatic pressure and gas tension (including oxygen tension) in culture medium, was used to evaluate the effects of pressure and tension on cell migration, shape, and α-tubulin architecture in a transformed cell line (DITNC1 rat cortical astrocytes).

METHODS. During the assay period, cells were exposed to one of four experimental configurations: (1) control pressure and control gas tension; (2) …

Impact Of Elliptical Trainer Ergonomic Modifications On Perceptions Of Safety, Comfort, Workout, And Usability For People With Physical Disabilities And Chronic Conditions, Judith M. Burnfield, Yu Shu, Thad W. Buster, Adam P. Taylor, Carl A. Nelson

Department of Mechanical and Materials Engineering: Faculty Publications

Background The popularity of elliptical training has grown in rehabilitation, fitness, and home settings as a means for improving fitness and walking, yet many people with physical disabilities and chronic conditions experience difficulties when trying to use elliptical trainers.

Objective The purpose of this study was to compare, for people with disabilities and chronic conditions, perceptions of safety, comfort, workout, and usability of 4 elliptical trainers before and after the development of a set of low-cost adaptations.

Design This study was a quasi-experimental repeated-measures investigation.

Methods Twenty adults with diverse medical conditions and functional abilities evaluated 4 elliptical trainers for …

Use Of Environmental Scanning Electron Microscopy For In Situ Observation Of Interaction Of Cells With Micro- And Nanoprobes, Alexander Goponenko, B. J. Boyle, K. I. Jahan, Maxim V. Gerashchenko, Dmitri E. Fomenko, Vadim N. Gladyshev, Yuris A. Dzenis

Department of Mechanical and Materials Engineering: Faculty Publications

Precision intracellular sensing, probing and manipulation offer unprecedented opportunities for advances in biological sciences. Next-generation ultra-fine probes will be capable of targeting individual cell organelles. Development of such probes as well as probes capable of penetrating through tough cell walls requires detailed knowledge of cell-probe interaction. This Letter evaluated the applicability of environmental scanning electron microscopy (ESEM) for cell and cell-probe interaction imaging. Several types of cells (plant and yeast cells as well as mouse spermatozoa) were successfully imaged in their natural state, with mouse spermatozoa observed by ESEM for the first time. Computerized stage applied to image was tough …

Nanomechanical Analysis Of Insulinoma Cells After Glucose And Capsaicin Stimulation Using Atomic Force Microscopy, Ruiguo Yang, Ning Xi, King Wai-Chu Lai, Bei-Hua Zhong, Carmen Kar-Man Fung, Chen-Geng Qu, Donna H. Wang

Department of Mechanical and Materials Engineering: Faculty Publications

Aim: Glucose stimulates insulin secretion from pancreatic islet β cells by altering ion channel activity and membrane potential in the β cells. TRPV1 channel is expressed in the β cells and capsaicin induces insulin secretion similarly to glucose. This study aims to investigate the biophysical properties of the β cells upon stimulation of membrane channels using an atomic force microscopic (AFM) nanoindentation system.

Methods: ATCC insulinoma cell line was used. Cell stiffness, a marker of reorganization of cell membrane and cytoskeleton due to ion channel activation, was measured in real time using an integrated AFM nanoindentation system. Cell height that …

Photoelectrochemical Properties Of N, S, And Cl Modified Nano Tio2 Thin Films, Hong Yun, Chang-Jian Lin, Jing Li, Rong-Gui Du

Journal of Electrochemistry

The nitrogen(N),sulfur(S) and chlorine(Cl) modified nano TiO₂ thin films were prepared by adding Ti(O-n-Bu)₄ as the precursor into concentrated HNO₃,H₂SO₄ and HCl Solutions,respectively,on different substrates in a sol-gel process.The photoelectrochemical performances of N,S and Cl modified nano TiO₂ thin films have been studied by UV-vis(DRS),photocurrent curves,EIS and OCP-time curves.N-modified TiO₂ nano films show better surface structure,which helps to improve the quantum efficiency of nano TiO₂ thin films.

The Mechanism Of 13CoAd/12Co Isotope Exchange At Pt Electrode,A Combined Study By Electrochemical In-Situ Infrared Spectroscopy And Dipole-Dipole Coupling Analysis, Sang-Zi Liang, Shao-Xiong Liu, Ling-Wen Liao, Qian Tao, Jing Kang, Yan-Xia Chen

Journal of Electrochemistry

In this contribution,we have analyzed the IR spectra of saturated CO adlayer at rough Pt film electrode as a function of fractional surface coverage of ¹³CO_ad /¹²CO recorded during ¹³CO_ad /¹²CO isotope exchange process according to dipole-dipole coupling theory and coherent potential approximation. By properly choosing the parameters of adlayer structure and dipole-dipole coupling interaction under coherent potential approximation, we demonstrated that we can successfully simulate the IR spectra as a function of the surface coverage of CO adlayer at rough Pt film electrodes by assuming that CO_ad molecules with low …

An In Situ Fourier Transform Infrared Spectroelectrochemical Study On Alcohols Electrocatalytic Oxidation At Pd Electrode In Acidic Solution, Hai-Ping Huang, Lian-Qin Wang, Pei-Kang Shen

Journal of Electrochemistry

The methanol and ethylene glycol electrooxidation on palladium electrode in acidic solution has been investigated by cyclic voltammetry and in situ Fourier transform infrared spectroelectrochemistry. It shows that the oxidation of methanol and ethylene glycol at Pd electrode cannot proceed until over 1.5 V in acidic and neutral media. The overpotential decreases and the peak current density increases with the reduction in pH values. The formation of the oxygen-containing species significantly affects the alcohol oxidation on Pd electrode. The in situ FTIR spectroscopic measurements show that the oxidation products of ethylene glycol on Pd electrode are CO₂ and oxalic …

In-Situ Surface Enhanced Raman Scattering Electrochemical Investigation Of 4-Aminoantipyrine On Silver Electrode, Li-Jun Zhang, Wei Song, Ling Chen, Zong-Rang Zhang, Hai-Feng Yang

Journal of Electrochemistry

In this paper, 4-AAP was self-assembled on silver surface to form monolayers. Surface-enhanced Raman Spectroscopy (SERS) was used to in-situ investigate the adsorption mechanism of the 4-aminoantipyrine(4-AAP) on silver surface dependent on shifting potentials and the effect of solution pH. Based on density functional theory(DFT) calculation of vibration modes,approximate assignment of 4-AAP SERS spectrum was conducted. In situ SERS spectral electrochemical experiments indicated that the 4-AAP monolayers experience a dynamic adsorption process from a tilted fashion to a more vertical mode for benzene ring and more parallel for pyrine ring with the potential applied toward more negative voltages. The complete …

Comparative Study Of Nanoporous Pt, Ptru And Ptruir Catalysts Using Electrochemical Ftir Spectroscopy, M. Amussen Robert, Holt-Hindle Peter, Nigro Samantha, Aicheng Chen

Journal of Electrochemistry

In recent years much effort has been put towards developing efficient Pt-based electrocatalysts for applications in fuel cells. With the rising cost of precious metals such as Pt,the need to enhance the activity and to decrease the load of catalysts is prominent. Herein we report on the synthesis and comparative study of nanoporous Pt,PtRu and PtRuIr electrocatalysts. The nanoporous electrodes were fabricated using a hydrothermal method and characterized by scanning electron microscopy (SEM) ,energy dispersive spectroscopy (EDS) ,X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) . The electrocatalytic activity of the fabricated nanopo- rous materials was evaluated using both CO …

In Situ Surface-Enhanced Raman Scattering Spectroscopic Study Of Sulfur Adsorption On Polycrystalline Platinum Electrode Surface, Bolian Xu, In-Su Park, Ying Li, De-Jun Chen, Yuye J. Tong

Journal of Electrochemistry

The paper reports the first in situ surface enhanced Raman scattering (SERS) spectroelectrochemistry study of sulfur adsorption and electro-oxidation on highly roughened polycrystalline Pt surface in both acidic and basic supporting electrolytes. The SERS spectra were taken at a constant electrode potential after accumulative electro-oxidation CVs of the Pt electrode with pre-adsorbed sulfur species and at different electrode potentials that were varied stepwise of the Pt electrode immersed in sulfur-containing electrolytes without pre-adsorbed sulfur species. In both cases,a dominant vibrational band at 299 cm^-1 in acidic electrolyte but at 310 cm^-1 in basic electrolyte was observed,which was assigned …

Preliminary Investigation Of Iron Protoporphyrin Sams On Platinum Electrodes By Surface Enhanced Vibrational Spectroscopies, Min Ma, Yao-Yue Yang, Han-Xuan Zhang, Wen-Bin Cai

Journal of Electrochemistry

In situ SERS and ATR-SEIRAS were applied to investigate the electrochemical and structural properties of iron protoporphyrin IX (FePP) self-assembled monolayers (SAMs) on Pt electrodes in 0. 1 mol· L -1 HClO₄. The potential dependent SERS spectra of the FePP SAM on a roughened Pt electrode with the enhancement factor of ca. 40 were acquired with the excitation line of 514 nm. Analyses of SERS data over the potential region from 0. 5 to -0. 3 V enabled to obtain potential dependent adsorption isotherms,from which the formal redox potential could be estimated to be ca. -0. 2 V. …

Studies Of Oxidation Processes Of Adsorbed And Solution Co On Pt(110) Electrode By Cyclic Voltammetry And In Situ Ftirs, Li Tian, Jun-Tao Li, Jin-Yu Ye, Chun-Hua Zhen, Shi-Gang Sun

Journal of Electrochemistry

The oxidation processes of adsorbed CO (COad) and solution phase CO (COsol) on Pt(110) electrode were investigated by cyclic voltammetry and in-situ FTIR spectroscopy. It has revealed that in comparison with COad on Pt(110) in a CO-free solution,the oxidation current peak of COsol in a CO-saturated solution is positively shifted ca. 168 mV,and the peak current density has been increased by 6. 70 times. Linear adsorbed CO (COL) is determined by in-situ FTIR spectroscopy as the main species,which is uniformly distributed on Pt (110) surface. In a CO-free solution,the onset potential of COL is measured by in-situ FTIRS ca. 0. …

Nano/Micro-Structured Electrode Materials For Lithium-Ion Batteries, Yu-Guo Guo, Zhong-Li Wang, Xing-Long Wu, Wei-Ming Zhang, Li-Jun Wan

Journal of Electrochemistry

Nanostructured materials are currently of interest as high performance anodes and cathodes for rechargeable lithium-ion batteries because of their novel nano-size effects and significantly enhanced kinetics. This review paper describes some recent developments in this field,addressing the size effects,morphology effects,as well as the functions of carbon coating layers toward lithium storage. Several"kinetically stabilized"nano/microstructured electrode materials and high-rate electrode materials with mixed-conducting networks based on the work of the authors are highlighted for illustration.

Electrocatalytic Oxidation Of Hcooh At Au(Core)-Pd(Shell)-Pt(Cluster) Nanocubes, Qing-Ning Jiang, Huan Li, Ning Yang, Ping-Ping Fang, Feng-Ru Fan, Zhong-Qun Tian

Journal of Electrochemistry

Gold nanocubes were synthesized by a two-step seed-mediated growth method. The Aucore-Pdshell and Au_core-Pd_shell-Pt_cluster nanocubes with controllable shell thickness of Pd and cluster coverage of Pt were synthesized by simply changing the amount ratio of H₂PdCl₄ or H₂PtCl₆. The samples were characterized by scanning electron microscope (SEM) , transmission electron microscopc (TEM) and cyclic voltammetry (CV). CV was then used to make a systematic study on the dependence of the electrocatalytic properties on the shell thickness of Au_core-Pd_shell and Pt coverage of Au_core-Pd …

Prerapation And Supercapacitor Property Of Mesoporous Carbon Nanofibers, Yong-Wen Wang, Ming-Bo Zheng, Jian Cao, Jie-Ming Cao, Guang-Bin Ji, Jie Tao

Journal of Electrochemistry

Two different mesoporous carbon nanofibers with large mesopore or core-shell structure were prepared by using the resol/F127 mixture to fill the AAO template. The morphology and structural parameters of the samples were characterized by SEM,TEM,and N₂ adsorption-desorption analysis. The supercapacitive behaviors of the electrodes were tested by cyclic voltammetry and galvanostatic charge-discharge. The results show that the specific capacitances of mesoporous carbon nanofibers increased obviously and the fine supercapacitive performances were achieved at high scan rate or large current density.

Nano-Sized Au On Nickel Foam As Cathode Of Alkaline Al-H2O2 Semi Fuel Cell, Shu-Li Chen, Bang-An Lu, Yao Liu, Gui-Ling Wang, Dian-Xue Cao

Journal of Electrochemistry

Nano-sized Au particles were deposited on a nickel foam substrate by a fast spontaneous deposition method using AuCl₃ as the source of Au. The effects of AuCl₃ concentration and deposition time on the size and distribution of Au particles,and the performance of the obtained Au/Ni electrode as the cathode of Al-H₂O₂ semi fuel cell were investigated. It was found that after the nickel foam was immersed in a 2 mmol·L^-1 AuCl₃ solution for 60 s,Au particles with diameters smaller than 100 nm were deposited on its surfaces and cover the surface completely. The …

Preparation And Electrochemical Behavior Of Li4Ti5O12 Nanosheets As Anode Material For Lithium Ion Battery, Yi-Fei Wang, Yu-Feng Tang, Zheng Qiu, Li Yang

Journal of Electrochemistry

Spinel lithium titanate(Li₄Ti₅O₁₂) nanosheets with a size range of 200 ～400 nm were synthesized by hydrothermal process from the amorphous hydrous titanium oxide precursors.The as-prepared products were characterized by X-ray powder diffraction(XRD),scanning electron microscopy(SEM) and transmission electron microscopy(TEM).The electrochemical behaviors of Li₄Ti₅O₁₂ electrode in conventional organic electrolyte and ionic liquid electrolyte were investigated by using cyclic voltammetry,galvanostatic charge-discharge and AC impedance techniques.The experimental results indicate that the as-prepared nanostructured Li₄Ti₅O₁₂,evaluated as anode material,exhibited good reversibility and cycle performance.It is expected to be a …

Electrocatalytic Reduction Of L-Cystine At Pb/Nanotio2 Film Electrode, Dao-Bao Chu, Feng Wang, Ying Xiao, Xue-Jiao Zhang

Journal of Electrochemistry

The nanoporous Ti-based TiO₂ films electrodes modified with Pb particles(Pb/nanoTiO₂) were prepared by using anodization and potentiostatic electro-deposition.The optimum deposition conditions were determined by comparing with various deposition potentials and time.The SEM analyses indicated that the TiO₂ films were homogeneous nanoporous structure,and the Pb particles well dispersed on the TiO₂ films.The L-cystine electrocatalytic activity reduction on the Pb/nanoTiO₂ film electrodes was investigated by cyclic voltammetry and Chronoamperometric curves.The results showed that this type of the electrode posseses high acticity and stability.

Luminescence Enhancement Of Cdte Nanostructures In Laf3:Ce/Cdte Nanocomposites, Mingzhen Yao, Xing Zhang, Lun Ma, Wei Chen, Alan G. Joly, Jinsong Huang, Qingwu Wang

Department of Mechanical and Materials Engineering: Faculty Publications

Radiation detection demands new scintillators with high quantum efficiency, high energy resolution, and short luminescence lifetimes. Nanocomposites consisting of quantum dots and Ce³⁺ doped nanophosphors may be able to meet these requirements. Here, we report the luminescence enhancement of LaF₃:Ce/CdTe nanocomposites which were synthesized by a wet chemistry method. CdTe quantum dots in LaF₃:Ce/CdTe nanocomposites are converted into nanowires, while in LaF₃ /CdTe nanocomposites no such conversion is observed. As a result, the CdTe luminescence in LaF₃:Ce/CdTe nanocomposites is enhanced about five times, while in LaF₃ /CdTe nanocomposites no enhancement was …

Method Of Transferring Strained Semiconductor Structure, Michael Nastasi

Department of Mechanical and Materials Engineering: Faculty Publications

The transfer of strained semiconductor layers from one substrate to another substrate involves depositing a multilayer structure on a substrate having surface contaminants. An interface that includes the contaminants if formed in between the deposited layer and the substrate. Hydrogen atoms are introduced into the structure and allowed to diffuse to the interface. Afterward, the deposited multilayer structure is bonded to a second substrate and is separated away at the interface, which results in transferring a multilayer structure from one substrate at least one strained semiconductor layer and at least one strain-induced seed layer. The strain-induced seed layer can be …

Progresses In Electrocatalysis Of Nanomaterials—Tuning The Surface Structure And Property Of Electrocatalysts, Yan-Xia Jiang, Na Tian, Zhi-You Zhou, Sheng-Pei Chen, Shi-Gang Sun

Journal of Electrochemistry

The property of an electrocatalyst depends strongly on its surface structure.The study of surface structure-catalytic functionality is the base of design and preparation of electrocatalysts of high activity,high stability and high selectivity at microstructure level.In this paper,based mainly on our results concering hydrogen and oxygen adsorption-desorption,ethylene glycol oxidation and CO₂ reduction,the research progresses in tuning the surface structure and property of electrocatalysts are summarized.This paper overviews firstly the cyclic voltammetric characteristics,electrocatalytic properties of platinum single crystal planes lying on different crystallographic zones of the unit stereographic triangle of face-centered cubic(fcc) metals.Next,the innovation of electrochemical methods to control the surface …