Mining Engineering Commons^™

An Investigation Of Failure Patterns Of Layered Specimens Loaded In Uniaxial Compression, Narendra Y. B. Choudary

Masters Theses

"Uniaxial compressive strength for two and three-layered specimens was obtained with different thicknesses of layers and also for different length to diameter ratios. The fracture and failure pattern was studied. Shear and extension fractures were observed in the layers. Geometry and end conditions of the specimen had a great influence in the failure and fracture pattern.

The uniaxial compressive strength of a layered specimen was found to be lower than the weighted average strength and either low or high when compared to the arithmetic average strength, depending on the ratio of the heights of the layers. The compressive strength of …

An Introduction To Linear Time-Variant Digital Filtering Of Seismic Data, Richard Harold Lassley

Doctoral Dissertations

"The exploration geophysicist is constantly searching for new and better methods for analyzing seismic data. The primary purpose of this dissertation is to introduce linear time-variant digital filters as a technique for the filtering of seismic data. Methods of characterizing linear time-variant digital filters are discussed in general terms. The advantages of the different impulse and frequency responses are cited. In addition, the meanings and possible interpretations of the time and frequency variables introduced are considered. The concept of linear time-variant digital delay filters is presented along with their relationship to impulse responses. A pictorial diagram of discrete time-variant impulse …

Use Of Spent Sulphite Liquor For Stabilization Of Fractured Rock And Sealing Off Water Bearing Formations, Laxman Singh Sunda

Masters Theses

"The paper industry, in its process of manufacturing pulp from wood, produces large quantities of a substance called lignin, lignin sulphite, or lignosulphonate. This material has been disposed of as a waste product; however, it does have many potential uses. In this investigation, lignosulfonates were used as agents for bonding rock sections together and, as the chief component of gels, for filling the pores of artificial rock cores. The purposes of these tests were to find how this substance could be used in the mining industry, for stabilizing fractured ground around mine openings and for sealing off water influx into …

The Development Of Conical Stress Forms By Explosive Charges, Walter T. Casquino

Masters Theses

"Usually stresses generated by explosive charges during blasting are considered to propagate through materials in a spherical manner. Although conical stress waves had been suggested by a few investigators they have never been clearly defined or studied in the laboratory.

An experimental technique using models was developed to produce conical stress waves from an explosive. Several materials with different properties were selected as models for the purpose of determining whether or not conical waves could be generated in all materials.

This investigation showed that conical stress waves do exist under certain conditions, which would closely approximate those present for much …

A Study Of The Influence Of Shock Waves On The Stability Of Rock-Bolt Anchorage, Helmut W. Habenicht

Masters Theses

"An experimental method was developed to compare strain data for rock and rock bolts when exposed to shock waves released by blasting. During a 32-day period of experimentation, one rock sensor and four rock-bolt sensors were observed simultaneously. By their placement in the side wall of a structurally stable drift, secondary static stresses were excluded. Bolt gage responses, then, could be considered to originate only from a decay of anchorage stability during static conditions or as a reaction to the vibrations. Interpretation of test results indicated a distinct loss in bolt-strain during vibrations, accompanied by a smaller but steady loss …

The Cementing Of Hydraulically Placed Tailing Fill By The Oxidation Products Of Pyrrhotite, Stanley H. Alder

Masters Theses

"This thesis has been prepared to make available basic information on the use of the oxidation products of pyrrhotite to cement hydraulic tailing stope fill. As nothing has been published on this subject to date, a review has been made of pertinent information culled from accounts of work in related fields. From this study, a set of equations representing the most likely pyrrhotite oxidation reactions has been evolved and tests supporting these equations performed. Samples of fill, each containing from one to six percent of pyrrhotite, were cemented in the laboratory. They were then examined microscopically, subjected to unconfined compressive …

A Study Of Plane And Spherical Compressional Waves In A Voigt Viscoelastic Medium, Gerald B. Rupert

Doctoral Dissertations

"In investigating the behavior of waves traveling through cohesive solids, two assumptions are usually made: that the propagating medium is either elastic or viscoelastic, and that the wave is either planar or spherical in form. For small distances from the source of the disturbance the medium can be considered elastic and the wave spherical rather than planar. The assumption of elasticity allows considerable simplification of the mathematical analysis, and assuming a spherical wave form is an acceptable approximation if the initial disturbance is essentially a point source and the propagating medium is nearly homogeneous. However, for large distances from the …

A Study Of The Phase Behavior Of Carbon Dioxide-Methane-Normal Decane Systems, Raja Audi Mansoor

Masters Theses

“The effect of carbon dioxide concentration, on solubility has been studied for several carbon dioxide-methane-n-decane systems. Experimental results were obtained using differential vaporization tests. Computational results were obtained using equilibrium constants.

The relation between solubility, bubble point pressure and solution carbon dioxide is presented. A ternary diagram showing the bubble point pressure behavior as a function of system composition is also presented”--Abstract, page ii.

The Characteristics Of Radial Strain Propagation Induced By Explosive Impact In Jefferson City Dolomite., Choon K. Quan

Masters Theses

"Blasting effects depend largely on peak radial strains propagated in rock media by explosive impact. To improve blasting design and control of secondary effects (e.g., structural fatigue), an equation for peak radial strain propagation induced by explosions was developed as follows: Emax = K e^-αr /r

An instrumental technique was designed to test the validity of the equation in the Jefferson City dolomite. Results showed ii that for 1-lb charges of 60% ammonia-gelatin explosive, peak strains, at any distance r, were reduced in amplitude in accordance with an exponential decay function of the type Emax = 281 e^{-0.026r …}

Investigations Of The Feasibility Of Transporting Ore In Open-Flumes., Kirtikant R. Sheth

Masters Theses

"Considerable effort has been expended and many data are published on developing the technologies of pipeline transportation and hydraulic hoisting. However, comparatively little information is available on the techniques of hydraulic mining, and nearly none ii is reported on conveying slurries in open flumes. For this reason, the author chose to investigate some of the parameters that influence open-flume transport.

It was found that Durand has assembled the findings of several investigators into a simple mathematical expression which is accepted as a standard for designing slurry pipelines. ·Further investigation by the writer revealed that Durand's formula, with only minor modification, …

Estimating Bench Design Parameters For Open-Cut Excavation, Rajni K. Gandhi

Masters Theses

"There are no direct relationships available that provide a basis for bench design of multiple-bench, open-cut earth excavations in competent materials when power shovels are employed. This study was undertaken to determine if mathematical design expressions could be developed when the production rate, material's properties, and equipment operating characteristics were known.

It was found that all bench dimensions were a function of the bench height, which in turn was controlled by the required rate of production. The investigation revealed that suitable relationships could be developed to guide in the control of bank stability, choice of shovel capacity, determination of the …

Application Of An Orifice Meter To Fan Testing., J. F. T. Agapito

Masters Theses

"In this investigation the application of an orifice meter to fan testing was studied and evaluated. An orifice meter was designed and was installed in a centrifugal fan duct. Measurements were checked and compared with those of a standard pitot-tube traverse and were found to be in very close agreement. It is suggested that a meter of this type could easily be adapted not only to laboratory work but also to field tests"--Abstract, p. ii

Ignition Time Lag: A Measure Of Explosive Energy Release, Paul H. Rydlund

Masters Theses

"By means of the resistance-element, or probe-wire, detonation-velocity measurement technique, explosive reactions from various blasting agents were studied. To reduce the number of variables, only standard AN-FO 94/6 mixtures were used, as are commonly employed today in constructions and mining operations. Accuracy of the data obtained was excellent, and the method proved itself not only relatively simple to operate but versatile in providing considerable information under many testing conditions. Studies of test records revealed the presence of a time-lag frequently occuring [sic] after primer detonation. Environmental factors such as confinement, charge diameter, primer size and energy content, and surface coatings …

A Laboratory Model Study Of Fluid Cross Flow., James Gary Fore

Masters Theses

"A procedure for scaling and operating a laboratory model for the purpose of studying fluid crossflow between zones of different permeability is presented. A modified existing model is used to simulate conditions for three dimensional, incompressible, two-phase flow through a two-layer, unconsolidated, homogeneous porous medium.

Eight tests were made to show effects on crossflow between the zones. Qualitative results indicate crossflow from the high to the low permeability zone for various perforation ratios and mobility ratios"--Abstract, p. ii

A Laboratory Study Of The Effect Of Wettability Of Residual Oil Saturation In Artificial Cores., Socrates Nicholas Potamianos

Masters Theses

"In the past much emphasis has been placed on various studies of reservoir rock and fluid surface properties and their relation to the different oil recovery processes. Several laboratory methods (1, 2, 3) ^l/have been used by different investigators to obtain a more fundamental understanding of the many factors which have an influence on the oil recovery from reservoir rocks"--Introduction, p. 1

Non-Ferrous Metal Mining And Smelting In Australia

School of Mines and Metallurgy Bulletins

Bulletin was published without an Abstract

Hydraulic Transportation Of Coal In Open Flumes., Nallapu Narayan Reddy

Masters Theses

"The objective of this study is to design a simplified form of hydraulic transportation system using open-flumes and operated by gravity in pitching coal seams. This type of system is to be used in conjunction with mining by hydraulic methods where the water used for the extraction of coal can also be used for the loading and transport functions"--Introduction p. 1

Some Effects Of Impact Of Low Magnitude On The Deformation Of Prestressed Gypsum Cylinders., Arthur Joe Bush

Masters Theses

"A review of the literature pertaining to the subject is presented. Many series or impacts were made on specimens of gypsum which were already under a static load. A special. repetitive impact machine was used to allow a variety or weights to fall from predetermined heights. Tests were conducted inside a roan constructed especially for these tests. Heat gained or lost through the ceiling and walls was kept at a minilI1um by a lining or aluminum-covered, fiber glass insulation. Temperature and humidity conditions were kept nearly constant by a combination air-conditioner and dehumidifier.

Repetitive loading of the prestressed specimen was …

Application Of Photoelasticity To The Stability Of Slopes In Open-Pit Mines., Aly Hemedah Gomah

Masters Theses

"A study of the stability of wall slopes in open pit mines was performed by preparing photoelastic epoxy-resin models representing open pit mines with various slope angles. The models were loaded centrifugally, using the 'locked-in' stress technique. Due to the relatively large sizes of the models, stress distributions could not be recorded with the photographic equipment available. Therefore, fringes and isoclinics were plotted directly on the models themselves. The fringes were used to calculate the shear stress concentrations at arbitrary points in the model from known stresses at control points in the models. The type of slope failure that was …

Analysis Of Problems In The Performance Of A Natural Gas Storage Reservoir., Gerald Eugene Henderson

Masters Theses

"A digital computer technique is presented for predicting two parameters of underground natural gas storage reservoir performance: (1) the prediction of reservoir pressures and volumes, and (2) the prediction of optimum flow rate and pressure drawdown for a single well in accordance with the theory of water coning.

The outlined procedure for predicting gas storage reservoir pressures and volumes was not effective for the field studies, although certain conclusions have been drawn which should be beneficial in further studies.

The procedure for predicting optimum gas flow rate and pressure drawdown from a well without production of bottom water involved first …

Development Of A Technique For The Determination Of Capillary Pressure Curves Using A Constantly Accelerated Centrifuge, Robert N. Hoffman

Masters Theses

"A new technique for determining capillary pressure curves with a centrifuge has been developed and tested. Capillary pressure curves were determined for six cores by this technique and were compared to the curves for the same cores determined by the semi-permeable barrier technique. The technique differs from previously reported centrifuge techniques in that the centrifuge was slowly accelerated from zero to the maximum desired speed, rather than being held constant at particular, progressively higher speeds. An important advantage of this technique over other methods for determining capillary pressure curves is the short time required to obtain the desired amount of …

A Model Investigation Of The Water Coning Phenomenon., Gary L. Downey

Masters Theses

"Results and procedures are presented covering the design and construction of a dimensionally scaled model of an oil reservoir and its use in investigating the problem of water coning. The theoretical considerations involved in the analytical solution of the water coning problem and the methods used in constructing, designing, and operating the above model are presented.

Four water coning experiments have been completed using the model. Three of the four runs have produced significant results. The information obtained from these experimental results have shown that the laboratory model is well suited for investigating oil reservoir problems such as water coning …

The Applicability Of Longwall Mining To American Coal Seams, Mehmet Turgut Tezcanli

Masters Theses

"The objective of this thesis is to show that mechanized longwall mining can be applied to thinner American coal seams with greater advantage than the conventional mechanized room-and-pillar methods now being used, provided that the proper equipment is employed in an effective manner."--Objective, page 1.

A Study Of The Stress Distribution Around Circular Openings Using Multilayered Photoelastic Material, Donald Frank Haber

Masters Theses

"Stress analysis as applied to mine openings ranges from the completely empirical to the completely theoretical. However, it is only through the ultimate utilization of the two methods that a guide to the Interpretation of mine stress phenomenon may be obtained. The bridge between the two approaches lies in the field of model study. Specifically, this is an Investigation into determining the feasibility of using multilayered photoelastic materials in models such that a more exact approximation of the underground stress distribution around mine openings can be made.

The two major objectives in this study for determining the feasibility of using …

Dipole Approximation Of The Solution For An Electrode Configuration In Two-Layer Resistivity Problem, Siew Hung Chan

Masters Theses

"An electrode configuration which consists of a pair of current electrodes, spaced at a unit apart, being kept at a great distance r from a pair of potential electrodes also spaced at a unit apart, has been investigated. Two theoretical apparent resistivity formulae were derived by applying Kelvin's theory of images to the problem of two-layer case. One formula is obtained by the exact method of solution, the other being obtained by considering the pair of current electrodes as a single dipole. Results of numerical calculations show that the greater the spacing r in comparison to the spacing a, …

The Influence Of Bench Geometry On Blasting Effects For Vertical Cylindrical Charges, Thomas E. Pearse

Masters Theses

"Blasting phenomena are affected by many factors. Previous investigators have studied many of these factors, however, the influence of charge length and explosive detonation velocity have apparently not been thoroughly examined.

It was found by this investigation that the detonation pressure of a commercial explosive is closely controlled by the detonation velocity. The detonation velocity, in turn, will largely determine the necessary blast geometry that can be successfully employed. Relationships were derived between the detonation velocity, in relation to the rock energy propagation velocity, and blast geometry for both bottom and collar primed blasts.

The resultant force magnitude and direction …

An Evaluation Of State Mineral Taxation In Missouri, Jerry Wayne Huffman

Masters Theses

"A study was made to evaluate the present taxes levied on the mineral industry in the State of Missouri. The corporate income tax, corporate franchise tax, and general property taxes were examined, in addition to the mine inspection fees and methods of local assessment of mineral properties.

It is suggested that the State of Missouri revise the method of application of the general property tax to mineral properties. Utilization of the principle of taxation of future profits and employment of qualified appraisers would provide a more equitable application of the general property tax.

It is recommended that the present mine …

A Model Study Of The Behavior Of Elastic Liners In Shallow Underground Openings, Martin Samuel Oudenhoven

Masters Theses

"Models of epoxy resin were used in a stress freezing technique to determine areas of possible failure in lined circular openings. These models were loaded in a centrifuge for a fixed period of time, after which they were analyzed photoelastically. The material characteristic changes, with time, were recorded on graphs and used in the analysis.

Two types of tests were conducted; one, where the lining thickness was changed and, the other, where materials of the liner and plate material were changed.

The resulting analyses furnished proof that the greater the rigidity of the lining, the higher the stress developed in …

A Model Study Of The Application Of Roof Bolts Under Unsymmetrical Loading Conditions, Friedrich H. K. Esser

Masters Theses

"When coal is extracted by the long wall mining method, two gate-roads on either side of the working face are driven with the advancing operation. In the surroundings of these openings the state of stress which existed prior to mining is not only disturbed by the drifting process of the gate-roads but also by the coal extraction in the long wall, resulting in an "unsymmetrical" stress distribution. Varying incremental pressure components and the high complexity of strata movements make it extremely difficult to control the rock behavior under unsymmetrical conditions by conventional support. Application of roof bolts as an auxiliary …

A Model Study Of The Induction Log Applied To The Detection Of Asymmetrically Located Orebodies, Robert Walter Piekarz

Masters Theses

"This research project was undertaken to determine the possibility of using an induction log of the type applied in petroleum exploration, for the detection of conductive ore- bodies asymmetrically located with respect to a borehole. Since a mathematical analysis would be extremely complex, a model study was conducted, using graphite bodies of various shapes to simulate different modes of mineral occurence.

The investigation showed that these bodies were readily detectable, and were capable of yielding anomalous curves characteristic of their geometry. The values of apparent conductivity decreased rapidly with lateral displacement, from the logging tool, as expected, due to the …