Mining Engineering Commons^™

Innovative Rts Technology For Dry Beneficiation Of Phosphate, Ahmed Sobhy, Daniel Tao

Mining Engineering Faculty Research & Creative Works

The Crago double flotation process is widely used for upgrading raw phosphate in Florida. However, it is a water-based physicochemical process and consumes a huge amount of water and chemicals and is not efficient to remove dolomite from phosphate. In addition, the final phosphate flotation concentrate often has a grade of 30-31% P2O5, which is below the BPL content of 75% (or 34.3% P2O5) required for making the animal feed grade phosphate. This study is performed to evaluate the potential and feasibility of the innovative rotary triboelectrostatic separator (RTS) as a dry phosphate beneficiation process. The RTS technology is characterized …

Distributional Fate Of Elements During The Synthesis Of Zeolites From South African Coal Fly Ash, Pieter W. Du Plessis, Tunde V. Ojumu, Ojo O. Fatoba, Richard O. Akinyeye, Leslie F. Petrik

Mining Engineering Faculty Research & Creative Works

The synthesis of zeolites from South African coal fly ash has been deemed a viable solution to the growing economical strain caused by the disposal of ash in the country. Two synthesis routes have been studied thus far namely the 2-step method and the fusion assisted process. Fly ash contains several elements originating from coal which is incorporated in the ash during combustion. It is vital to determine the final destination of these elements in order to unveil optimization opportunities for scale-up purposes. The aim of this study was to perform a material balance study on both synthesis routes to …

Determining And Mitigating The Effects Of Firing A Linear Shaped Charge Under Water, Brian Burch

Masters Theses

"When fired under water, a Linear Shaped Charge (LSC) does not penetrate a steel target as well as in air. This lack of performance has been a problem for shaped charge manufacturers and their clients. It was obvious that this degradation of performance is due to water having a higher density than air and water being incompressible compared to air. This study aimed to better determine how the water was affecting the LSC and to provide a method of mitigation.

LSCs of different sizes were submerged under water and fired through the water with and without a target. It was …

Laboratory Study On The Mobility Of Major Species In Fly Ash-Brine Co-Disposal Systems: Up-Flow Percolation Test, O. O. Fatoba, L. F. Petrik, R. O. Akinyeye, W. M. Gitari, E. I. Iwuoha

Mining Engineering Faculty Research & Creative Works

Apart from the generation of fly ash, brine (hyper-saline wastewater) is also a waste material generated in South African power stations as a result of water re-use. These waste materials contain major species such as Al, Si, Na, K, Ca, Mg, Cl and SO4. The co-disposal of fly ash and brine has been practiced by some power stations in South Africa with the aim of utilizing the fly ash to capture the salts in brine. The effect of the chemical interaction of the species contained in both fly ash and brine, when co-disposed, on the mobility of species in the …

Comparison Between Neural Networks And Multiple Regression Methods In Metallurgical Performance Modeling Of Flotation Column, Fardis Nakhaei, Mehdi Irannajad

Mining Engineering Faculty Research & Creative Works

Artificial neural networks are relatively new computational tools which their inherent ability to learn and recognize highly non-linear and complex relationships makes them ideally suited in solving a wide range of complex real-world problems. In this research, different techniques (Linear regression, Non-linear regression, Back propagation neural network, Radial Basis Function for the estimation of Cu grade and recovery values in flotation column concentrate are studied. Modeling is performed based on 90 datasets at different operating conditions at Sarcheshmeh pilot plant, a copper concentrator in Iran, which include chemical reagents dosage, froth height, air and wash water flow rates, gas holdup …

Nanobubble Column Flotation For More Efficient Coal Recovery, Ahmed Sobhy, R. Honaker, D. Tao

Mining Engineering Faculty Research & Creative Works

Froth flotation is a widely used, cost effective coal cleaning process. However, its high process efficiency is limited to a narrow particle size range between approximately 50 to 600 μm for coal and 10 to 100 μm for minerals. Beyond this range, the efficiency of froth flotation decreases sharply, especially for difficult-to-float coal fines of weak hydrophobicity (e.g., oxidized coal).

This study was aimed at enhancing recovery of an Illinois fine coal sample using a flotation column featuring a hydrodynamic cavitation nanobubble generator. Nanobubbles that are mostly smaller than 1 μm can be formed selectively on hydrophobic coal particles from …

Methods For Evaluating Effect Of Operators On Drag Line Energy Efficiency, Maryam Abdi Oskouei

Masters Theses

"Draglines are dominant machines and the most significant electricity consumers in surface coal mines. With the growing price of energy, environmental concerns, and the high sensitivity of mine profitability to dragline productivity, any improvement in efficiency of dragline will be beneficial for mines. Research has shown that operator practices have a significant impact on energy efficiency of mining loading tools. However, not enough work has been done to provide guidance on how to quantitatively assess the effect of operator practices on dragline energy efficiency.

The objectives of this work were to: (i) test the hypothesis that dragline operator's practices and …

Stochastic-Optimization Of Equipment Productivity In Multi-Seam Formations, Elijah Adadzi

Masters Theses

"Short and long range planning and execution for multi-seam coal formations (MSFs) are challenging with complex extraction mechanisms. Stripping equipment selection and scheduling are functions of the physical dynamics of the mine and the operational mechanisms of its components, thus its productivity is dependent on these parameters. Previous research studies did not incorporate quantitative relationships between equipment productivities and extraction dynamics in MSFs. The intrinsic variability of excavation and spoiling dynamics must also form part of existing models. This research formulates quantitative relationships of equipment productivities using Branch-and-Bound algorithms and Lagrange Parameterization approaches. The stochastic processes are resolved via Monte …

A Review Of Pharmaceuticals And Endocrine-Disrupting Compounds: Sources, Effects, Removal, And Detections, Jimoh O. Tijani, Ojo O. Fatoba, Leslie F. Petrik

Mining Engineering Faculty Research & Creative Works

There are growing concerns about the increasing trends of emerging micropollutants in the environment due to their potential negative impacts on natural ecosystems and humans. This has attracted attention from both governmental and non-governmental organizations worldwide. Pharmaceuticals, personal care products, and endocrine disruptors are continuously being released consciously or unconsciously into water sources due to poor regulatory frameworks especially in the developing countries. The effects of these contaminants are poorly known. They are not easily biodegradable and have become an environmental nuisance and public health issue. This has heightened the risk of exposure to their deleterious effects in such countries …

Extension Of Thickness-Dependent Dielectric Breakdown Law On Adiabatically Compressed Ferroelectric Materials, S. I. Shkuratov, Jason Baird, E. F. Talantsev

Mining Engineering Faculty Research & Creative Works

It is experimentally found that the E_b(d) = γ  · d ^-ξ law describing the thickness-dependent breakdown electric field for solid dielectrics at ambient conditions can be extended for dielectrics in other thermodynamic states. It follows from the experimental results reported herein that the breakdown field, E_b(d), of Pb(Zr₀.₉₅Ti₀.₀₅)O₃ (PZT 95/5) and Pb(Zr₀.₅₂Ti₀.₄₈)O₃ (PZT 52/48) ferroelectrics subjected to explosive adiabatic compression obeys the above-mentioned law in a wide range of voltages, up to 150 kV.

Utilization Of Booster Fans In Underground Mines, Arash Habibi Javanbakht

Masters Theses

"Booster fans are large underground fans that can increase the volumetric efficiency of ventilation systems by balancing the pressure and quantity distribution throughout a mine, reducing leakage and reducing the total power requirement. The objective of this study is to provide potential users of booster fans with the necessary information on the design, installation and operation of main underground fans. The guidelines listed in this paper were formulated based on current U.S. and international standards, safe operating practices developed by the mining industry, and recommendations provided by fan manufacturers. The principles involved in the design and installation of booster fans …

Spatial Variation Of Amd Related Co₂ Emissions On Reclaimed Mine Spoil, Moagabo Mathiba

Doctoral Dissertations

"Carbon dioxide (CO₂) from acid mine drainage (AMD)-carbonate neutralization reactions in reclaimed mine spoils, can intermittently invade homes and structures constructed on or adjacent to these spoils in hazardous and even lethal concentrations (>15%) and rendering them uninhabitable. This phenomenon is beginning to be recognized as an emerging environmental, safety and health threat with potential environmental and financial liability for mine operators, developers and owners.

Like in natural soils, soil temperature and moisture, and possibly elevation are likely to influence CO₂ emissions from reclaimed mine spoils. However, mine spoil soils are heterogeneous and have significant convective transport due to …

Explosively Formed Projectile Soft-Recovery Force Analysis, Laurin Bookout, Phillip R. Mulligan, Jason Baird

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

The design of a soft-recovery system is critical to a researcher's ability to analyze hypervelocity projectiles. The researcher may decide to use one method over another based on several criteria, including whether or not non-deformed projectile measurements are required. This report analyzes the forces two different soft-recovery methods impart on the projectiles collected. Method 1 utilized three polyethylene water barrels placed “end-to-end” horizontally, providing 2.6 meters (9 feet) of water to stop the projectile. Method 2 is a modification of the soft-recovery method utilized in “Soft-Recovery of Explosively Formed Penetrators” by Lambert and Pope. This method utilizes a series of …

Method And Apparatus For Jet-Assisted Drilling Or Cutting, David A. Summers, Klaus Woelk, Kenneth Doyle Oglesby, Greg Galecki

Mining Engineering Faculty Research & Creative Works

An abrasive cutting or drilling system, apparatus and method, which includes an upstream supercritical fluid and/or liquid carrier fluid, abrasive particles, a nozzle and a gaseous or low-density supercritical fluid exhaust abrasive stream. The nozzle includes a throat section and, optionally, a converging inlet section, a divergent discharge section, and a feed section.

Production Scheduling And Waste Disposal Planning For Oil Sands Mining Using Goal Programming, E. Ben-Awuah, H. Askari-Nasab, Kwame Awuah-Offei

Mining Engineering Faculty Research & Creative Works

In oil sands mining, timely provisions of ore and tailings containment with less environmental footprints are the main drivers of profitability and sustainability. The recent Alberta Energy Resources Conservation Board Directive 074 requires oil sands waste disposal planning to be an integral part of mine planning. This requires the development of a well integrated strategy of directional mining and tailings dyke construction for in-pit and ex-pit tailings storage management. The objectives of this paper are to: 1) determine the order and time of extraction of ore, dyke material and waste that maximizes the net present value; 2) determine the destination …

Effect Of Shock Front Geometry On Shock Depolarization Of Pb(Zr 0.52ti 0.48)O₃ Ferroelectric Ceramics, S. I. Shkuratov, Jason Baird, E. F. Talantsev

Mining Engineering Faculty Research & Creative Works

By use of experimentation, we detected a shock wave geometry effect on the depolarization of poled PbZr_0.52Ti_0.48)O₃ Z(PZT 52/48) ferroelectrics. It follows from the experimental results that shock front geometry is one of key parameters in the shock depolarization of PZT 5248 ferroelectrics. This shock depolarization effect forms a fundamental limit to miniaturization of explosive-driven shock-wave ferroelectric generators (FEGs). Based on obtained experimental results, we developed miniature generators that reliably produce pulsed voltages exceeding 140 kV.

Note: Utilizing Pb(Zr 0.95ti 0.05)O₃ Ferroelectric Ceramics To Scale Down Autonomous Explosive-Driven Shock-Wave Ferroelectric Generators, S. I. Shkuratov, Jason Baird, E. F. Talantsev

Mining Engineering Faculty Research & Creative Works

Further miniaturization of recently designed autonomous ferroelectric generators (FEGs) S. I. Shkuratov, J. Baird, and E. F. Talantsev, Rev. Sci. Instrum. 82, 086107 (2011), which are based on the effect of explosive-shock-wave depolarization of poled ferroelectrics is achieved. The key miniaturization factor was the utilization of high-energy density Pb(Zr_0.95Ti_0.05)O₃ (PZT 955) ferroelectric ceramics as energy-carrying elements of FEGs instead of the previously used Pb(Zr_0.52Ti_0.48)O₃ (PZT 5248). A series of experiments demonstrated that FEGs based on smaller PZT 955 ferroelectric elements are capable of producing the same output voltage as those …

The Effects Of The Flyer Plate's Radius Of Curvature On The Performance Of An Explosively Formed Projectile, Phillip R. Mulligan, Jason Baird, Joshua Hoffman

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

An explosively formed projectile (EFP) is known for its ability to penetrate vehicle armor effectively. Understanding how an EFP’s physical parameters affect its performance is crucial to development of armor capable of defeating such devices. The present study uses two flyer plate radii of curvature to identify the experimental effects of the flyer plate’s radius of curvature on the measured projectile velocity, depth of penetration, and projectile shape. The Gurney equation is an algebraic relationship for estimating the velocity imparted to a metal plate in contact with detonating explosives. The authors of this research used a form of the Gurney …

The Effects Of Water On Sympathetic Detonation And Dead Pressing Of Dynamite And Emulsions, Adam Michael Doerfler

Masters Theses

Dynamite and emulsions are very effective explosives in blasting; however they do have some shortcomings. Dynamite is prone to sympathetic detonation whereas emulsions are prone to dead pressing. While this does not happen all the time, the conditions in which the explosives are used do have an effect on whether or not they will sympathetically detonate or dead press.

Numerous researchers have investigated sympathetic detonation for a relationship between the distance between charges, hole separation distance, and size of explosive. This research aimed to look at how hole separation distance was affected when water was introduced into the boreholes for …

3d Finite Element Analysis Of Pwa-Oil Sand Terrain System Interaction, Y. Li, Samuel Frimpong, W. Y. Liu

Mining Engineering Faculty Research & Creative Works

A simulator for analyzing the interaction between the oil sand terrain and a pipe wagon articulating (PWA) system has been developed in this paper. An elastic-plastic oil sand model was built based on the finite element analysis (FEA) method and von Mises yield criterion using the Algor mechanical event simulation (MES) software. The three-dimensional (3D) distribution of the stress, strain, nodal displacement, and deformed shape of the oil sands was animated at an environmental temperature of 25C. The 3D behavior of the oil sand terrain was investigated with different loading conditions. The effect of the load and contact area on …

Finite Element Analysis Of Blade-Formation Interactions In Excavation, Osei Brown

Masters Theses

"The efficiency and costs of mining operations greatly depend on the efficient design and use of excavators. The performance of these capital-intensive excavators requires thorough understanding of the physical and design factors that affect the formation-cutting tool interaction process. The current body of knowledge, based on experimental and analytical methods, provides limited understanding of these factors, which limits the accurate design and performance of excavators. The soil constitutive equations used in most of the available finite element (FE) models also fail to adequately capture the elastic and plastic behaviors of soil formations. This research initiative uses FE techniques to model …

Fractal Oxidation Kinetics And Risk Evaluation Of Spontaneous Combustion In Coal Mines, Yutao Zhang

Doctoral Dissertations

"The spontaneous combustion of coal occurs when air supply is sufficient for the oxidation of coal and air velocity is insufficient for the dissipation of generated heat. Spontaneous combustion, if not eradicated immediately, may lead to coal ignition and even a full-blown fire. The fire may engulf a large area and spread further if they are not immediately attended to. This will not only endanger miners and mining operations, but also result in possible mine closures and even fatalities.

Porous structure has a significant effect on coal adsorption and spontaneous combustion. In this research, fractal theory was utilized to quantitatively …

Underground Mine Fire Simulation Using Multiscale Modeling Approach, Xichen Zhang

Doctoral Dissertations

"Underground mine fires have always been a major concern. Past events show that fire poses a severe safety hazard to mine workers, and causes tremendous economic loss to the mine and surrounding communities. A good understanding of the interaction between a mine fire and the mine ventilation network is crucial for effective fire emergency planning and hazard control. Unfortunately our understanding of a fire is still limited due to the complex nature of mine fires and a lack of adequate resource for studying them.

A new multiscale modeling approach coupling conventional 1D and 3D techniques has shown to be a …

Effects Of Coal Comminution In Relation To Waterjet And Selected Feed Properties, Yaqing Li

Masters Theses

"The necessity to develop a viable alternative to oil means that the development of coal-water fuels (CWF) has become increasingly important. However, the existing methods of comminution to prepare ultrafine particles for CWF are very inefficient. Consequently, a number of novel methods of comminution have been investigated in order to increase the efficiency of the process.

In this research, a new method of comminution using a high-pressure waterjet has been tested to produce ultrafine particle sizes necessary for efficient CWF process. To establish the fundamental performance of the waterjet mill, the influence of the operational pressure, standoff distance, feed size, …

A Reversibility Analysis Of Encoding Methods For Spiking Neural Networks, Catherine Johnson, S. Roychowdhury, Ganesh K. Venayagamoorthy

Mining Engineering Faculty Research & Creative Works

There is much excitement surrounding the idea of using spiking neural networks (SNNs) as the next generation of function-approximating neural networks. However, with the unique mechanism of communication (neural spikes) between neurons comes the challenge of transferring real-world data into the network to process. Many different encoding methods have been developed for SNNs, most temporal and some spatial. This paper analyzes three of them (Poisson rate encoding, Gaussian receptor fields, and a dual-neuron n-bit representation) and tests to see if the information is fully transformed into the spiking patterns. an oft-neglected consideration in encoding for SNNs is whether or not …

Note: Miniature 120-Kv Autonomous Generator Based On Transverse Shock-Wave Depolarization Of Pb(Zr0.52ti0.48)O₃ Ferroelectrics, S. I. Shkuratov, Jason Baird, E. F. Talantsev

Mining Engineering Faculty Research & Creative Works

The design of autonomous ultrahigh-voltage generators with no moving metallic parts based on transverse explosive shock wave depolarization of Pb(Zr_0.52Ti_0.48)O₃ (PZT 5248) poled ferroelectrics was explored and studied. It follows from experimental results that the output voltage produced by the shock-wave ferroelectric generators (FEGs) is directly proportional to the number of PZT 5248 elements connected in series. It was demonstrated that miniature FEGs (volume less than 180 cm³) were capable of reliably producing output voltage pulses with amplitudes exceeding 120 kV which is the record reported in open literature.

Electric Breakdown Of Longitudinally Shocked Pb(Zr₀.₅₂Ti₀.₄₈)O₃ Ceramics, S. I. Shkuratov, E. F. Talantsev, Jason Baird

Mining Engineering Faculty Research & Creative Works

Electric breakdown of longitudinally-shock-compressed Pb(Zr₀.₅₂Ti₀.₄₈)O₃ (PZT 52/48) ferroelectric ceramics was experimentally investigated. It was found that a dependence of breakdown field strength, E_g, of shocked ferroelectrics on the thickness of the element, d, ranging from 0.65 to 6.5 mm is described by the E_g (d) = γ  · d^-w law that describes the breakdown of dielectrics at ambient conditions. It follows from the experimental results that the tunnel effect is a dominant mechanism of injection of prime electrons in the shocked ferroelectric elements. It was demonstrated that electric breakdown causes significant energy losses in miniature autonomous …

The Depolarization Of Pb(Zr0.52ti0.48)O₃ Ferroelectrics By Cylindrical Radially Expanding Shock Waves And Its Utilization For Miniature Pulsed Power, S. I. Shkuratov, Jason Baird, E. F. Talantsev

Mining Engineering Faculty Research & Creative Works

The effects of depolarization of Pb(Zr_0.52Ti_0.48)O₃ (PZT 52/48) poled ferroelectrics by cylindrical radially expanding shock waves propagated along and across the polarization vector P₀ were experimentally detected. Miniature (total volume 100 cm³) autonomous generators based on these effects were capable of producing output voltage pulses with amplitudes up to 25 kV and output energies exceeding 1 J.

Pressed Powdered Titanium And Aluminum Conical Shaped Charge Penetration Of Geological Targets, Dominique John Nolan

Masters Theses

"Conical Shaped Charge penetration into rock is dependent on the physical characteristics of the rock itself and the design and composition of the shaped charge conducting the work. This study looks at the effects of a non-typical conical shaped charge and its penetration into four different rock targets. The shaped charge is made of a liner, which is not a typical solid but instead is a pressed powdered metallic compound of Titanium (Ti) and Aluminum (AI).

The study presents the raw data from testing against rock targets that range in density, uniaxial compressive strength (UCS), tensile strength, hardness scales, and …

The Effects Select Physical Parameters Have On An Explosively Formed Projectile's Performance, Phillip R. Mulligan

Masters Theses

"Identifying how changes in the physical parameters of an Explosively Formed Projectile (EFP) affect its performance is crucial in determining what physical parameters could be changed to achieve a desired performance. This research analyzes five of the physical parameters of an EFP, similar to an Iranian design (Worsey, 2009), and the effects on performance. The five physical parameters selected for this research were charge weight, confining geometry, flyer thickness, flyer curvature, and explosives-type. Eighteen different EFP designs were used to test the penetration, measured velocity, production of a dominant projectile, and kinetic energy of these five physical parameters. Of the …