Other Mechanical Engineering Commons^™

Numerical Simulation Of Airflow Properties Of The Naca 6420 Airfoil Using The Transition Rans K-Ε Model, Oluwaseyi O. Alabi, Saidat A. Salisu, Oyeyemi T. Aforolagba -Balogun, Temitope A. Ladigbolu, Ayotunde O. Fasina, Anas Bala

Al-Bahir

This study investigates the airflow properties around the airfoil using numerical simulation, addressing the longstanding challenge of accurately predicting transition phenomena in turbulent flows. The importance of this research lies in its potential to improve the design and performance of airfoils in various engineering applications, such as wind turbines, and aircraft. A custom 2-dimensional airfoil model was created using Airfoil instruments, featuring a 6% maximum curvature, 40% curvature position, and 20% thickness. COMSOL Multiphysics software performed computations at a velocity of over 19 hours, with data analyzed at 60-minute intervals. The Transition turbulent model was employed to simulate the airflow …

Evaluating Energy Efficiency And Thermal Performance In Egypt’S Social Housing: Climate-Responsive Design And Material Impact In Hot Desert Environments, Ahmed M. Hanafi, Mohamed A. Moawed, Osama E. Abdullatif

Journal of Engineering Research

As Egypt's urban areas expand rapidly, the demand for energy-efficient, affordable housing in extreme hot desert climates has become increasingly urgent. This study investigates the energy efficiency and thermal performance of Egypt’s Social Housing Project, with a focus on residential building in New Aswan City, where summer temperatures frequently exceed 45°C. Employing a validated energy model, this research simulates annual energy consumption for the building, which comprises 24 residential units, each approximately 86 m². The model integrates realistic occupancy schedules, region-specific weather data, and common household behavior patterns to closely reflect actual energy usage. Findings indicate a high alignment between …

Experimental Study On A Hybrid Solar Distillation System Integrated With A Photovoltaic Thermal Collector For The Co-Production Of Electricity And Freshwater, S. A. El Agouz, Mohamed Samy Abo Shala, Ayman Refat Abd Elbar

Journal of Engineering Research

This experimental study investigates the performance of a hybrid solar still system integrated with a photovoltaic (PV) panel and a cooling system, with the goal of enhancing both the freshwater productivity and the performance of the photovoltaic panel. Over a span of four consecutive days, four distinct experimental cases were tested in Tanta (Longitude/Latitude: E 31° 0′/ N 30° 47′), each with different cooling water flow rates of (3 L/min, 6 L/min, and 9 L/min) for cooling the lower surface of photovoltaic panel, and different hot water flow rates of (0.6 L/hr, 0.9 L/hr, and 1.2 L/hr) input to …

A Computational Fluid Dynamics Approach To Analyze The Virtual Impactor In Pneumatic Aerosol Jet Printing, Akashita Sareen

Theses, Dissertations and Capstones

Aerosol jet printing (AJP) is a 3D printing, advanced manufacturing process that generates an aerosol mist appropriate for fine printing small, low-volume electronic parts. The pneumatic aerosol jet printing technology’s virtual impactor is the focus of this study. In this technology, high velocity nitrogen gas aerosolizes various inks in the atomizer. The aerosolized stream of ink is then transported to a virtual impactor (VI) to become dense and concentrated as it begins to enter the deposition head for high precision electronics printing. AJP faces challenges in large-scale adoption due to challenges related to overspray, instability, ink clogging etc. There is …

Design Strategy For Hybrid Thrust Air Bearings: Comparative Analysis Of Rigid Vs. Foil Bearings Considering Optimum Taper Angle And Orifice Location With Experimental Validation, Ehiremen Ebewele

Mechanical and Aerospace Engineering Dissertations - Archive

Gas foil thrust bearings (GFTBs) are contactless bearings that offer advantages such as lightweight construction and the ability to accommodate misalignments and geometric irregularities. However, their load capacity is lower than rigid or magnetic bearings. The structure and geometry of the foil significantly influence GFTB performance. The taper-flat design is the most used configuration due to its effectiveness and ease of implementation. Key parameters in designing this geometry include taper ratio, taper height, orifice size, and orifice location. These parameters must be optimized alongside manufacturing constraints to produce an effective GFTB. This study presents a design optimization investigation of various …

Deep Neural Network Models For Heatsink Performance Prediction And Optimization In Single Phase Immersion Cooling: Framework For Future Design Tools And Digital Twin Integration, Braxton J. Smith

Mechanical and Aerospace Engineering Theses - Archive

The rapidly rising computational power of modern computing components combined with the advanced packaging techniques being implemented has resulted in exponentially increasing thermal design powers (TDP) from CPUs and GPUs. Traditional air-cooling methods are approaching their effective cooling limits for many of these components, requiring lower supply air temperatures, higher supply air flowrates, and much larger heatsinks to remain feasible. Transitioning from air-cooling to single-phase immersion cooling offers numerous benefits in thermal performance, data-center size reduction, and energy efficiency. To leverage the merits of immersion cooling, the performance of a given heatsink must be predicted and optimized for best performance …

Aeg Improved Football Helmet Liner, Matthew Dyson, John Clore, Brady Slates, Nathan Walker

Williams Honors College, Honors Research Projects

The National Football League (NFL) is a leading professional American football organization experiencing rapid growth in popularity. However, the high-contact nature of the sport frequently results in player injuries, with head trauma and concussions being major concerns. This project aims to mitigate these risks by developing an advanced helmet liner designed to reduce the impact of direct collisions and torsional shear forces. In order to do this, we will utilize an impact testing machine with a modified helmet mount. By enhancing the liner's effectiveness, the proposed design seeks to improve player safety without compromising performance. The study focuses on innovative …

Nebraska Summary #1293: Fendt 618 Vario, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary #1292: Fendt 616 Vario, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Test #2301: Claas Xerion 12.650, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Test #2298: John Deere 9rx 830, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Test #2297: John Deere 9rx 770, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Test #2296: John Deere 9rx 710, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Test# 2299: Claas Xerion 12.590, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Test #2269: Case Ih Steiger 645, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary #1298: Fendt 726 Vario Gen 7.1, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary #1294: Fendt 620 Vario, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary #1291: Fendt 614 Vario, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Transient Thermal Finite Element Simulation For Process Modeling In Wire Arc Additive Manufacturing, Satya Sai Kumar Pilli

Dissertations, Master's Theses and Master's Reports

This thesis presents the development of a transient thermal framework for Wire Arc Additive Manufacturing (WAAM) created using ANSYS Workbench. This study aims to understand the inherent properties and thermal behavior of WAAM by using the Finite Element (FE) simulation technique to reduce the need for experiments. Specifically, the transient thermal WAAM simulation framework uses the heat source Goldak model to understand the thermal behavior for a given voltage, initial temperature, and travel speed during the process to predict process temperature. The outcomes of this thesis aim to significantly decrease material waste and repetitive experiments and accelerate production process design …

Ioto: Never Open A Stiff Lid Again, Gabriel Portugal

Libraries Award for Undergraduate Scholarship

Background: From baby food to pickles, food jars are a common find in American homes. Unfortunately,  the task of opening a stiff jar lid can be very difficult for consumers with lower grip strength, parkinsons,  or arthritis. While there are a variety of products on the market to help make this easier, there exist few jar  openers that can be used by these consumers. Objective: This project aimed to research and develop  (R&D) an improved hands-free jar opener that is accessible for consumers with the most advanced  cases of limited arm strength. Methods: R&D followed a Design Thinking approach with …

Scaling Investigations Of Wall-Bounded Turbulent Flow, Nikolay Gustenyov

Theses and Dissertations--Mechanical and Aerospace Engineering

This dissertation investigates the scaling behavior, structural organization, and modeling of turbulence in wall-bounded flows across a wide range of Reynolds numbers and surface conditions. Through high-resolution experimental studies in zero-pressure- gradient turbulent boundary layers and pipe flows (2000 < Reτ < 38 200), the wall- dependence of turbulent length scales is examined with a focus on both small-scale dissipative motions and large-scale structures. When external intermittency is properly accounted for, dissipative motions are shown to obey inner scaling even in outer- scaled regions, while large-scale motions exhibit outer scaling behavior deep into the inner region. These findings are consistent across internal (pipe) and external (boundary layer) flows and are reflected in distinct features of the longitudinal wavenumber spectrum.

The dissertation also explores the development of a turbulent boundary layer transitioning from a smooth solid wall to a liquid surface. An internal boundary layer forms in response to stochastic surface waves, resulting in increased turbulence intensity and displaced momentum relative to solid-wall cases. Near the liquid surface, turbulence generation aligns with wavenumbers corresponding to the surface waves, introducing distinct small-scale …

High-Altitude Balloon-Launched Uncrewed Aircraft System Measurements Of Atmospheric Turbulence And Qualitative Comparison With Infrasound Microphone Response, Anisa Haghighi

Theses and Dissertations--Mechanical and Aerospace Engineering

This study explores the use of a balloon-launched uncrewed aircraft system (UAS) to measure atmospheric turbulence in the troposphere and lower stratosphere using both wind velocity measurements and infrasonic acoustic energy. The UAS, a glider configured for autonomous descent along a predefined trajectory, had on board, in situ sensors to capture thermodynamic and kinematic atmospheric parameters. Additionally, it carried an infrasonic microphone to evaluate its potential for remotely detecting clear-air turbulence by capturing infrasonic waves. The system’s performance was assessed over the course of three test flights conducted in New Mexico, USA, in 2021. The descent enabled high-resolution profiling, with …

Nebraska Test #2302: Claas Xerion 12.650 Terra Trac, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Test #2300: Claas Xerion 12.590 Terra Trac, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Test #2268: Case Ih Steiger 595, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Effect Of Build Orientation On Tensile Properties And Fractography Of Additive Manufactured Inconel 718 Alloy, Ajay Kumar Maurya, Amit Kumar, Swarnambuj Suman

ASEAN Journal on Science and Technology for Development

The additive manufacturing (AM) technique “Direct Metal Laser Sintering (DMLS)” is used to create 3D objects directly from 3D design data. A lightweight and complexity-free part without any expensive tooling can be fabricated easily using this method, but it is still challenging to achieve the desired mechanical strength from AM parts, as the mechanical properties of AM-produced parts vary with orientation, scan strategy, and process parameters. Inconel 718 alloy is most commonly utilized in the aerospace and automotive industries, because of its high resistance to corrosion and excellent mechanical qualities. This work presents a study to investigate the orientation-based mechanical …

A Finite Volume-Based Approach For Modeling Hyperbaric Oxygen Therapy For Healing Chronic Wounds, Cade M. Layser

College of Graduate Studies: Theses & Dissertations

The current number of people in America with diabetes is approximately 38.4 million, that population is expected to rise to 54.9 million by 2030. Chronic wounds, which are characterized by impaired or stalled healing, are commonly associated with diabetes. These wounds if not treated properly can cause significant complications such as sepsis, infection, and gangrene which can lead to limb amputation or death of the patient. Limb amputations can be a large financial burden and significantly reduce the patient’s quality of life. The timely and efficient treatment of chronic wounds is essential to prevent adverse patient outcomes. Hyperbaric Oxygen therapy …

Cost-Effective Brake Rotor Resurfacing Tool, Raider Morgan, Benjamin Vaughan

Williams Honors College, Honors Research Projects

Brake rotors can develop uneven spots over time, causing vibration and poor braking performance. Commercial brake lathes are effective but often too expensive or complicated for at-home mechanics. This project aimed to create a low-cost tool, around $200–$300, to resurface four rotors in under two hours. We explored two main designs: a pad file system and a motorized endmill powered by a handheld drill. Calculations ultimately showed that the pad file was not viable, so the final prototype produced was the endmill-based design. Our testing showed we were limited by poor stiffness in the endmill and unforeseen loading. Although the …

Zips Baja Chassis Manufacturing Design, Alex Love, David Scruppi

Williams Honors College, Honors Research Projects

The Society of Automotive (SAE) annually organizes collegiate design team competitions for university organizations nationwide. Baja SAE tasks teams comprised entirely of students with developing, iterating, manufacturing, testing, and competing with an offroad race buggy in accordance with all SAE regulations. Teams are responsible for producing a tech compliant vehicle for each competition season, travelling across the United States to put their designs to the test. In the 2022-2023 competition season, SAE introduced ruleset clarifications on the chassis manufacturing process, essentially mandating the production of all vehicle frames to be manufactured entirely in house with no external assistance. A chassis …

Dual Rotating Mount For Forward Facing Sonar, Javid Miller

Williams Honors College, Honors Research Projects

This project aims to create a mount for forward facing sonar (FFS) that will allow anglers to be able to rotate their sonar transducer manually, or in unison with their trolling motor. When in use with the trolling motor, the rotation will be transferred using a belt and pulley assembly. This assembly will be able to be disengaged to allow for manual rotation. This device is designed for use with the Minn Kota Ultrex trolling motor.