Other Mechanical Engineering Commons^™

Nebraska Tractor Summary: 1234 John Deere 6r 145, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2260: John Deere 9r 490, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Wireless Power Transfer In Autonomous Mobile Microgrids, Carl Greene

Dissertations, Master's Theses and Master's Reports

The ability to autonomously dock unmanned ground vehicles plays a key role in mobile micro-grids, where efficient power transfer is paramount. The approach utilized in this work allows for near-field wireless power transfer in remote locations with minimal support. Establishing a micro-grid power system connection autonomously using wireless power eliminates the arduous task of designing a complex, multiple degrees of freedom (MDOF) robotic arm. The work presented in this thesis focuses on both the hardware and software within the micro-grid system. This particular near-field wireless system consists of a primary and secondary set of modules, comprised of Litz wire coils, …

An Experimental Study Towards Underwater Propulsion System Using Structure Borne Traveling Waves, Shreyas Suhas Gadekar

Dissertations, Master's Theses and Master's Reports

The method of generating steady-state structure-borne traveling waves underwater in an infinite media creates abundant opportunities in the field of propulsive applications, and they are gaining attention from several researchers. This experimental study provides a framework for harnessing traveling waves in a 1D beam immersed under quiescent water using two force input methods and providing a motion to an object floating on the surface of the water.

In this study, underwater traveling waves are tailored using structural vibrations at five different frequencies in the range of 10Hz to 300Hz. The resulting fluid motion provides a propulsive thrust that moves a …

Permeability, Structural Changes, Flow Regime Transitions In Fuel Cell Catalyst Layers And A Model For Predicting Trapped Saturation For Two-Phase Flow In Porous Media, Karrar Takleef Alofari

Dissertations, Master's Theses and Master's Reports

Proper water management in Proton Exchange Membrane (PEM) fuel cell is important to achieve high performance. Understanding the percolation of the produced water at the cathode catalyst layer (CL) is critical for any robust water management technique. In this study, an ex-situ experimental setup is used to study percolation in the CL at different injection rates and relative humidity (RH) conditions. The results show that increasing the flow rate force the liquid to flow through the bulk of the pores due to the dominant viscous effect. On the other hand, at low injection rates, the capillary becomes dominant and liquid …

Nebraska Summary: 1231 John Deere 6r 120 Diesel Infinitely Variable Transmission, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Ballistic Impact Mitigation Pad, Adam Pianalto, Nathan Mayer, Wyatt Smith, Nick Green, Douglas Wild

Williams Honors College, Honors Research Projects

In our senior design project we have decided to work under Dr. Jon Gerhardt on creating a gel pad to mitigate blunt force behind bulletproof vests. Extensive research on injury, materials, manufacturing methods, and NIJ standards was completed during this project. Through the use of advanced modeling software and additive manufacturing, we prototyped a functioning pad to test and compare to a pad that is currently available in today's market. The results proved to be very successful, but there are many areas to improve upon down the road.

Dupont Seal Mold Assembly Machine, Brett Biederman, Craig Hanchett, Matthew Chilton

Williams Honors College, Honors Research Projects

The Seal Assembly Machine is a custom-built device that is designed to seat a thin polymer part between two mating pieces of metal tooling. To meet the specifications of the sponsor, the Seal Assembly machine must perform its function more quickly and accurately than manual labor at the same task. At the time of compiling this report, the machine is not yet functional due to time constraints.

Zip Shoes, Derek Ford, Garret Freund

Williams Honors College, Honors Research Projects

For our honors project we intend to create a new urban mobility solution. They are called Zip Shoes; they will be a pair of shoes with built in propulsion. We plan to use our cumulative engineering knowledge to modify an existing pair of shoes such that they can safely propel the user on wheels. We hope to achieve this by adding an electric drive train and necessary structural components onto the shoes. We are pursuing this project because we have seen the popularity of other electronically driven personal transportation devices. These include the hover board, electric skateboards, and electric scooters. …

Recycled Printer Filament, Charlotte Hyland, Troy D. Molinar

Williams Honors College, Honors Research Projects

The purpose of this research is to examine the effects of recycling PLA filament for 3D printing on its material properties. After examining these effects, PLA and carbon fiber additives were mixed with recycled PLA pellets in different ratios to attempt to regain material properties lost in the recycling process. To complete these findings, an experiment was design and executed.

The research found that tensile strength during multiple iterations of recycling remained mostly unaffected, however, the strain degraded exponentially. In the PLA additive study, high ratios of PLA additive were able to increase the strength and strain properties of the …

Visualization And Validation Of Twin Nucleation And Early-Stage Growth In Magnesium, Lin Jiang, Mingyu Gong, Jian Wang, Zhiliang Pan, Xin Wang, Dalong Zhang, Y. Morris Wang, Jim Ciston, Andrew M. Minor, Mingjie Xu, Xiaoqing Pan, Timothy J. Rupert, Subhash Mahajan, Enrique J. Lavernia, Irene J. Beyerlein, Julie M. Schoenung

Department of Mechanical and Materials Engineering: Faculty Publications

The abrupt occurrence of twinning when Mg is deformed leads to a highly anisotropic response, making it too unreliable for structural use and too unpredictable for observation. Here, we describe an in-situ transmission electron microscopy experiment on Mg crystals with strategically designed geometries for visualization of a long-proposed but unverified twinning mechanism. Combining with atomistic simulations and topological analysis, we conclude that twin nucleation occurs through a pure-shuffle mechanism that requires prismatic-basal transformations. Also, we verified a crystal geometry dependent twin growth mechanism, that is the early-stage growth associated with instability of plasticity flow, which can be dominated either by …

Npt Test Machine, Lauren Cash

Williams Honors College, Honors Research Projects

Located at the Research facility at The Goodyear Tire & Rubber Company, the Non-Pneumatic Tire (NPT) Program is currently in the prototype phase. However, airless tire structures are quickly gaining popularity as an alternative to a traditional pneumatic tire. The NPT Test Machine is a measurement fixture that will perform a series of evaluations to determine the stiffness of an NPT; this will allow the program to expand and evolve more rapidly into a manufacturing phase. In this Senior Design Project, a complete test solution was researched, designed, built, programmed, and validated so that data can be collected, and tires …

Golf Club Cleaner, Owen Roach, Chris Wertenberger, Michael Skerlong

Williams Honors College, Honors Research Projects

Cleaning golf clubs can be a tedious process, however a necessary one to maintain equipment. Clubs are normally cleaned by filling a bucket with soap and water, soaking all the clubs to be cleaned, then scrubbing each one individually. An automatic club cleaner would make this process much easier and more enjoyable. Using electric motors, the club cleaner would have spinning brushes in soap and water to quickly and easily clean the club head. The machine would have different sections for cleaning the club head, polishing the club face, and cleaning the grip. The cleaner should be inexpensive and easy …

Concept Evaluation And Development Of A Novel Approach For Integration Of Turbogeneration, Electrification And Supercharging On Heavy Duty Engines, Satyum Joshi

Dissertations, Master's Theses and Master's Reports

While many technologies such as electrically assisted turbocharging, exhaust energy recovery and mild hybridization have already proven to significantly increase heavy-duty engine efficiency, the key challenge to their widespread adoption has been their cost effectiveness and packaging. This research specifically addresses these challenges through evaluation and development of a novel technology concept termed as the Integrated Turbogeneration, Electrification and Supercharging (ITES) system. The concept integrates a secondary compressor, a turbocompound/expander turbine and an electric motor through a planetary gearset into the engine cranktrain. The approach enables a reduced system cost and space-claim, while maximizing the efficiency benefits of independent technologies. …

Type Iii And Iv Deformation Twins In Minerals And Metals, John P. Hirth, Greg Hirth, Jian Wang

Department of Mechanical and Materials Engineering: Faculty Publications

Type IV twins are defined and shown to exist in triclinic crystal systems, as well as in some monoclinic and trigonal systems. Here, we focus on Pericline twins in triclinic plagioclase as an example. Type IV twins are associated with the irrationality of one of the twinning elements that is rational for a type II twin. The formation of type IV twins is accomplished through the shear on a K2 plane produced by the motion of twinning disconnections on a K1 plane, followed by rotational partitioning. The same systems where type IV twins are present also have type III twins …

Emissivity Prediction Of Functionalized Surfaces Using Artificial Intelligence, Greg Acosta, Andrew Reicks, Miguel Moreno, Alireza Borjali, Craig Zuhlke, Mohammad Ghashami

Department of Mechanical and Materials Engineering: Faculty Publications

Tuning surface emissivity has been of great interest in thermal radiation applications, such as thermophotovoltaics and passive radiative cooling. As a low-cost and scalable technique for manufacturing surfaces with desired emissivities, femtosecond laser surface processing (FLSP) has recently drawn enormous attention. Despite the versatility offered by FLSP, there is a knowledge gap in accurately predicting the outcome emissivity prior to fabrication. In this work, we demonstrate the immense advantage of employing artificial intelligence (AI) techniques to predict the emissivity of complex surfaces. For this aim, we used FLSP to fabricate 116 different aluminum samples. A comprehensive dataset was established by …

Construction Of A Peridynamic Model For Viscous Flow, Jiangming Zhao, Adam Larios, Florin Bobaru Ph.D.

Department of Mechanical and Materials Engineering: Faculty Publications

We derive the Eulerian formulation for a peridynamic (PD) model of Newtonian viscous flow starting from fundamental principles: conservation of mass and momentum. This formulation is different from models for viscous flow that utilize the so-called “peridynamic differential operator” with the classical Navier- Stokes equations. We show that the classical continuity equation is a limiting case of the PD one, assuming certain smoothness conditions. The PD model for viscous flow is calibrated to the classical Navier-Stokes equations by enforcing linear consistency for the viscous stress term. Couette and Poiseuille flows, and incompressible fluid flow past a regular lattice of cylinders …

Ultrathin Coding Metasurface For Underwater Wave Focusing, Branching And Self-Bending Generation With One Single Actuator, Lixie Song, Zhong Chen, Mehrdad Negahban, Lei Liang, Zheng Li, Zheng Wu

Department of Mechanical and Materials Engineering: Faculty Publications

A novel metasurface is proposed that aims to generate underwater acoustic waves with various functions by only one actuator. Each metasurface unit consists of an air cavity sandwiched on one side by a vibration plate and connecting rubber supports. By properly selecting the ratio of the plate to unit lengths, a phase shift of π can be attained to constitute a binary coding metasurface. Three demonstrations, including focusing, branching and self-bending waves, are chosen to validate the functionality of the design. The design is also shown to work over a wide frequency range through changing the ratio. In addition, the …

Machine Learning Assisted Metamaterial‑Based Reconfigurable Antenna For Low‑Cost Portable Electronic Devices, Shobhit K. Patel, Jaymit Surve, Vijay Katkar, Juveriya Parmar

Department of Mechanical and Materials Engineering: Faculty Publications

Antenna design has evolved from bulkier to small portable designs but there is a need for smarter antenna design using machine learning algorithms that can meet today’s high growing demand for smart and fast devices. Here in this research, main focus is on developing smart antenna design using machine learning applicable in 5G mobile applications and portable Wi-Fi, Wi-MAX, and WLAN applications. Our design is based on the metamaterial concept where the patch is truncated and etched with a split ring resonator (SRR). The high gain requirement is met by adding metamaterial superstrates having thin wires (TW) and SRRs. The …

Symmetric Or Asymmetric Glide Resistance To Twinning Disconnection?, Mingyu Gong, Houyu Ma, Kunming Yang, Yue Liu, Jian-Feng Nie, Jian Wang

Department of Mechanical and Materials Engineering: Faculty Publications

Successive gliding of twinning disconnections (TDs) creates three-dimensional twins in parent crystal and accommodates shear deformation. It is generally recognized that TD is subject to the same Peierls stress as it glides forward or backward because of its dislocation character and the twofold rotation symmetry of the twin plane. Based on atomistic simulations, we demonstrate that the glide of TDs may be subject to a symmetric or asymmetric resistance corresponding to step character, symmetric resistance for A/A type steps but asymmetric resistance for A/B type steps, where A and B represent crystallographic planes in twin and matrix. Furthermore, we experimentally …

Recent Advances In Biosensors For Detection Of Covid-19 And Other Viruses, Shobhit K. Patel, Jaymit Surve, Juveriya Parmar, Kawsar Ahmed, Francis M. Bui, Fahad Ahmed Al-Zahrani

Department of Mechanical and Materials Engineering: Faculty Publications

This century has introduced very deadly, dangerous, and infectious diseases to humankind such as the influenza virus, Ebola virus, Zika virus, and the most infectious SARS-CoV-2 commonly known as COVID-19 and have caused epidemics and pandemics across the globe. For some of these diseases, proper medications, and vaccinations are missing and the early detection of these viruses will be critical to saving the patients. And even the vaccines are available for COVID-19, the new variants of COVID-19 such as Delta, and Omicron are spreading at large. The available virus detection techniques take a long time, are costly, and complex and …

A Robot-Assisted Acoustofluidic End Effector, Jan Durrer, Prajwal Agrawal, Ali Ozgul, Stephen C.F. Neuhauss, Nitesh Nama, Daniel Ahmed

Department of Mechanical and Materials Engineering: Faculty Publications

Liquid manipulation is the foundation of most laboratory processes. For macroscale liquid handling, both do-it-yourself and commercial robotic systems are available; however, for microscale, reagents are expensive and sample preparation is difficult. Over the last decade, lab-on-a-chip (LOC) systems have come to serve for microscale liquid manipulation; however, lacking automation andmulti-functionality. Despite their potential synergies, each has grown separately and no suitable interface yet exists to link macro-level robotics with micro-level LOC or microfluidic devices. Here, we present a robot-assisted acoustofluidic end effector (RAEE) system, comprising a robotic arm and an acoustofluidic end effector, that combines robotics and microfluidic functionalities.We …

Ternary Flow Simulation Based On The Conservative Phase Field Lattice Boltzmann Method, Chunheng Zhao

Dissertations and Theses

In this thesis, we numerically investigated multi-phase fluid dynamics (2 and 3-phase flow) by solving the Navier-Stokes equations coupled with the conservative phase field (CPF) equations using the Lattice Boltzmann method (LBM). To effectively simulate the large-scale multi-phase physics, we developed an open-source software, IMEXLBM, which can be easily parallelized on both CPUs and GPUs without significant modifications to the code. We first validated various parts of this software and then used this method to study the interaction of rising bubbles with a static oil droplet as well as the engulfment of the water droplet on solids coated with a …

Understanding The Relationship Between Urban Areas And The Boundary Layer Using Remote Sensing Methods, Gabriel A. Rios

Dissertations and Theses

The atmospheric boundary layer is crucial to the exchange in energy between the Earth's surface and the atmosphere. Within this layer, the majority of human activities are carried out, which makes understanding the boundary layer especially important for many of our interests. A key component of this energy exchange is found at the surface, was surface properties are the interface through which momentum, heat, moisture, and other fluxes are transferred between media. Not only does the surface act as an interface, but as an actor that influences the exchange efficiency and rates. This concept is the crux of atmospheric boundary …

Investigations Of The Low Temperature Combustion Regions And Emissions Characteristics Of Aerospace F24 In A Constant Volume Combustion Chamber And A Common Rail Direct Injection Ci Engine, Richard C. Smith Iii

College of Graduate Studies: Theses & Dissertations

A study was conducted to investigate the low temperature combustion (LTC) regions of aerospace F24 and ULSD in the static setting of a CVCC and the dynamic setting of a CRDI research engine. This research is conducted to reduce in-cylinder emissions by understanding and implementing a technique to achieve an extended LTC. Emissions data for this study were collected during the operation of the CRDI research engine with a MKS 2030 FTIR and an AVL Microsoot 483. The parameters researched within the static setting of the CVCC included the determinations of the cool flames and NTC regions within the LTHR …

Effects Of Titanium And Cerium Addition On Grain Size And Mechanical Properties Of Ductile Iron Castings, Shelton F. Fowler Iv

College of Graduate Studies: Theses & Dissertations

According to the Hall-Petch equation, the refinement of grains in metals increases the yield strength of the material. Austenite grain size influences the fineness of microstructural constituents in the ferrous alloys. It is well studied that cerium and titanium refine the austenite in steels and some gray irons, but no studies have been done to systematically explore the effects of cerium and titanium additions on austenite in ductile iron. This study sought to determine the effects of selected levels of these elements on the grain size within ductile iron. A hypoeutectic iron was chosen for testing as the proeutectic phase …

Comparison Of Maintenance Cost Of Medium And Heavy-Duty Alternative Fuel And Diesel Vehicles, Isaac C. Boyce

Graduate Theses, Dissertations, and Problem Reports (ETD)

Abstract

Comparison of Maintenance Cost of Medium and Heavy-Duty Alternative Fuel and Diesel Vehicles

Isaac Boyce

This study was conducted to provide an in-depth analysis of the differences in maintenance cost with the use of alternative fuel and diesel in medium (MD) and heavy-duty (HD) vehicles. With the push toward lower emissions from transportation vehicles for a cleaner future, the United States of America (US) has incentivized the conversion from the use of conventional fossil fuel, diesel, to lower carbon alternatives. With the increased potential for the use of alternative fuels, an investigation is warranted to understand the differences. This …

Branched Chain Amino Acid Strain State Monitoring With Raman Spectroscopy And Plasmonic Bowtie Nanoantenna Devices For Early Disease Detection, Caroline A. Campbell

Theses and Dissertations

This work centers on the development and the down-selection of nano-manufactured devices to be used in conjunction with Raman spectroscopy for probing a branched chain amino acid. The nano-manufactured devices integrate plasmonic nanoantennas for the purpose of amplifying molecular fingerprints, which are otherwise difficult to detect, through Surface Enhanced Raman Spectroscopy (SERS). Plasmonic nanostructures can be utilized for a variety of biomedical and biochemical applications to detect the characteristic fingerprint provided by Raman Spectroscopy. The nano-manufactured devices create an electric field that amplifies minute perturbations and raises the signal above background noise. This may provide a deeper understanding of signal …

Development And Optimization Of A Low Volume Air-Jet Dry Powder Inhaler (Dpi) Platform For The Delivery Of High Dose Aerosolized Powder To Infants, Connor Howe

Theses and Dissertations

The goal of this research project was to develop an infant air-jet dry powder inhaler (DPI) platform for high-efficiency nose-to-lung (N2L) aerosol administration to infants through optimization of individual system components followed by expansion of the system to higher doses and different formulations using a new approach. Primary challenges associated with aerosol delivery to infants using the N2L route include the extremely narrow extrathoracic airways, short inspiratory times (~0.2 sec), low safe airway pressure (H₂O), and very low volumes of air (~10 mL) available to form the aerosol. The infant air-jet DPI system was comprised of three main …

Magneto-Exothermic Catalytic Chemical Reaction Along A Curved Surface, Muhammad Ashraf, Uzma Ahmad, Saqib Zia, Rama S. R. Gorla, Amnah S. Al-Johani, Ilyas Khan, Mulugeta Andualem

Faculty Publications

In the current study, the physical behavior of the boundary layer flows along a curved surface owing exothermic catalytic chemical reaction, and the magnetic field is investigated. The mathematical model comprised of a part of momentum, energy, and mass equations, which are solved using a finite difference method along with primitive variable formulation. Numerical solutions, using the method of quantitative differentiation, are made with the appropriate choice of dimensionless parameters. Analysis of the results obtained shows that the field temperature and flow of fluids are strongly influenced by the combined effects of catalytic chemical reactions and the magnetic field. The …