Other Mechanical Engineering Commons^™

Experimental Investigation Of The Wind Energy Harvesting Potential Of A Stand-Alone Piezoelectric Strip, Phillip Christopher Scott

Mechanical Engineering ETDs

The purpose of the study was to investigate the feasibility of harvesting wind energy on a small scale in residential areas. The method investigated was the initiation of movement-induced excitation (MIE), a type of aeroelastic flutter, within samples of polyvinylidine fluoride (PVDF), a piezoelectric polymer. Single samples of PVDF were secured in a wind tunnel and sample voltage was measured over a broad range of wind speeds. Power was calculated then via the addition of ohmic resistance matched to the magnitude of the capacitive impedances of the samples. The geometry of the PVDF samples studied was maintained as a simple …

Comparison Of Plantar Pressure Profile Of Young Adults During Training On Elliptical Devices And Overground Walking: A Pilot Study, Guilherme Manna Cesar, Thad W. Buster, Judith M. Burnfield

Department of Mechanical and Materials Engineering: Faculty Publications

Background: Elliptical training may offer advantages over other cardiorespiratory exercises for those requiring podiatric care, since its constant double-limb support diminishes recurring high-impact plantar forces while allowing exercise in a functional, upright posture. Unknown is the impact of distinct elliptical models, that can alter user’s body mechanics, on potential variations in plantar pressure patterns.

Purpose: To compare plantar pressure variables while exercising on four ellipticals and walking.

Methods: For this cross-sectional pilot study, plantar pressure data were recorded from ten young adults while exercising on four ellipticals (True, Octane, Life Fitness, SportsArt) and walking overground. One-way repeated measures ANOVA identified …

Magnetically Induced Carrier Distribution In A Composite Rod Of Piezoelectric Semiconductors And Piezomagnetics, Guolin Wang, Jinxi Liu, Wenjie Feng, Jiashi Yang

Department of Mechanical and Materials Engineering: Faculty Publications

In this work, we study the behavior of a composite rod consisting of a piezoelectric semiconductor layer and two piezomagnetic layers under an applied axial magnetic field. Based on the phenomenological theories of piezoelectric semiconductors and piezomagnetics, a one-dimensional model is developed from which an analytical solution is obtained. The explicit expressions of the coupled fields and the numerical results show that an axially applied magnetic field produces extensional deformation through piezomagnetic coupling, the extension then produces polarization through piezoelectric coupling, and the polarization then causes the redistribution of mobile charges. Thus, the composite rod exhibits a coupling between the …

Influence Of Elements Of Irrigation Equipment On Irrigation Erosion, M.M. Sarimsakov, O.S. Abdisamatov, Z.T. Umarova

Irrigation and Melioration

Irrigation erosion is a process that has a significant negative impact on agricultural production, which leads to a sharp decrease in soil fertility and productivity. The costs associated with growing crops will increase. Today, more than 720,000 irrigated lands in the country suffer from irrigation erosion. Studies have shown that in typical gray soils with a slope of more than 0.30, intensive irrigation of apple orchards leaches 24.6 tons of soil particles per hectare per season. Improved irrigation, that is, a decrease in the leaching of soil particles during irrigation using transverse barriers, was achieved by 6–12%. Irrigation reduces the …

Research Of Water Flow Motion In The Channel Of Amu-Bukhara Machine Channel, D.R. Bazarov, F. Artikbekova, M.P. Tashkhanova, B.M. Norkulov

Irrigation and Melioration

The article considers a numerical study of the movement of a water stream in the channel of the Amu Bukhara Machine Channel (ABMK). Water intake to the inlet canal is carried out from the Amu Darya river in a damless manner, therefore, ensuring the flow of clarified water into the anterior chambers of pumping stations is an urgent task. According to the developed model, consisting of hydrodynamic equations based on the laws of conservation of momentum and mass, data on the dynamics of velocities in the channel of the supply channel ABMK are obtained and zones of uneven flow in …

Irrigation Value The Mechanical Composition River Springs, A.M. Arifjanov, L.N. Samiev, F.K. Babajanov

Irrigation and Melioration

The article studies the influence of the fractional composition of river sediments on the soil structure of irrigated lands and on the process of soil formation. According to surveys in the Mirishkor canal, sediments formed in the river are distinguished by the distribution type in the main canal. The fractional composition of sediments mainly consists of particles of fine sand (0.1-0.05 mm) and coarse dust (0.05-0.001 mm).According to the results of surveys, by studying the mechanical composition of sediment in the channel, it will be possible to observe changes in the amount of composition, such as N-NH4, P2O5, K2O chemicals. …

Monitoring System For Electricity Consumption At Pumping Stations, N. Ikramov, T. Majidov, A. Mukhammadjonov

Irrigation and Melioration

Currently, in Uzbekistan, of 4.3 million hectares of irrigated land, 2.3 million hectares are provided with water supplied by pumping stations that are on the balance of the Ministry of water management of the Republic of Uzbekistan. In total, 1693 pumping stations with 5301 pumping units are operated, and the number of pumping stations ' personnel is about 16,000 people. The total capacity of these pumping stations is about 7000 m3/s. the Total annual energy consumption of these pumping stations is about 8.0 billion kW·h or about 12.5% of the annual electricity generation of the entire energy sector of Uzbekistan. …

Irrigation Value The Mechanical Composition River Spring The Effect Of The Inhomogeneity Of Elastic Medium On The Initiation Of Resonant Waves Under Moving Load, S.A. Abdukadirov, Z.S. Shаdmаnova, B.Sh. Yuldoshev

Irrigation and Melioration

investigated. The waveguide properties of the system are preliminarily studied. The multiple roots of the dispersion equations are revealed and the critical load velocities leading to the formation of resonance processes are determined. The solutions of the dispersion equations make it possible to determine the additional critical velocities in the mid-wave spectrum depending on the structure parameters. For simple models, analytical solutions of the development of resonance processes are obtained that are asymptotically correct for relatively large values of time. The computer simulations allow us to analyze the quantitative features of the process over the entire time period of the …

Substantiation Of Sprayers Installed To A Universal Mounted Sprayer, D. Dzhuraev, M.S. Halilov, S.M. Badalov, I.Zh. Toirov, A.E. Urishev

Irrigation and Melioration

The article presents the results of theoretical and experimental studies on the creation of primary sprayers for sprayers. The flow diagrams of the atomizers that were produced on the territory of the former Soviet Union are given. Currently, various types of spray guns are manufactured in America, Germany, France, Italy, Bulgaria and other countries. Based on the set requirements for sprayers, to ensure fluid flow and spraying when deployed 90-110 degrees on a plane, a slotted sprayer is selected - manufacturer Lechler of the brand ST-110-05 Germany, for installation on a universal mounted sprayer. The results of fluid flow by …

Technological Features Of Moistening Of Technical Seeds, O. Matchanov, B. Tuxtamishev

Irrigation and Melioration

This article describes the technological features of the reduction of technical varieties of cotton. Requirements for technical seeds in the processing of raw cotton are technical specifications and quality indicators. Seeds of technical cotton with quality indicators and adapted technical seeds must meet the requirements of technical conditions. The technical need for coated seeds should correspond to technical characteristics, such as reducing production costs, reducing moisture, long-term storage, improving quality, thermal conductivity, aerodynamic resistance, and heat resistance. From the point of view of heat treatment of seeds, parameters taking into account their thermophysical properties should be used to justify the …

Regulations Of Hydraulic Resistance Of Machine Channels Of Pumping Stations, D.R. Bazarov, B.R. Uralov, M.P. Tashkhanova

Irrigation and Melioration

The paper considers the general equation of fluid motion in the channels and the functional dependences of the hydraulic friction coefficient on the Reynolds number, relative roughness, and on the shape of the live section of the channel. Resistance formulas are given for the simplest cross-sectional shapes of channels and for channels with a more complex cross-sectional shape. To take into account the effect (on the pressure loss) of the channel cross-sectional shape and the presence of a flow with a free surface in it, additional correction factors are introduced (using the hydraulic radius concept) and be clarified as a …

Studying The Movement Of Crop Drined Seeds Of Cottage On A Slope Tray In A Protective Machine, R.K. Djamolov, A.A. Akrаmov, K. Djamolov

Irrigation and Melioration

The article presents the results of a theoretical study of the movement of pubescent cotton seeds along an inclined guide in a pickling machine. Equations are obtained that describe the movement of the seed along the inclined tray of the dresser. A formula is derived for determining the time of movement of the seed on an inclined one to the dressing agent. A plot of the change in the speed of the seed in the tray on the change in the angle of inclination and on the value of the movement of the seed. To increase the feed rate of …

Modernization Of Functions Of Management Of Land Use In The Conditions Of Innovative Economy, Sh.K. Narbaev

Irrigation and Melioration

Land use management, as a complex material-abstract system, is carried out through a number of its functions. The article provides an analysis of the functions of land management, improved the content of some functions and introduced additional new functions in the context of the development of an innovative economy. It is noted that improving the management system will increase the efficiency of land use, improve their environmental status, preserve landscape ecosystems based on the accelerated development of innovative activities. New land management functions are recommended: innovative land use development, territory development, land use technical support, remote study of land properties …

Combined Installation Photo Thermal Battery - Electric Water Heater To Provide Electricity And Water To Rural Households, R.A. Muminov, M.N. Tursunov, Х. Sabirov, U.R. Kholov, Т.Z. Аkhtamov, М. Eshmuradova

Irrigation and Melioration

The article presents the experimental results of the study of the parameters of a combined installation photo thermal battery – electric heater, used to provide electric energy and water to rural households. Photo thermal battery is made on the basis of photovoltaic batteries of crystalline silicon with an efficiency of ~ 20 %. Cellular polycarbonate was used as a heat sink. When creating the KU based on photo thermal battery EVN, modern efficient batteries, controllers, inverters and consumers of electric energy were used, and Ariston was chosen as the EVN. KU is adapted to climatic conditions, effectively and reliably provides …

Modeling The Movement Of A Heap In A Dielectric Sorting Device For Alfalfa Seeds, A. Lee, Z. Sharipov, M.N. Sattarov

Irrigation and Melioration

This article presents a theoretical study of modeling the movement of a mixture in a dielectric sorting plant for alfalfa seeds. Theoretical studies were carried out using the general laws of mechanics and mathematical modeling of alfalfa seeds, taking into account their physical and mechanical properties. The results of a theoretical study on modeling the detachment conditions of alfalfa seed heap particles and particle dynamics along the casing and pitched boards of a dielectric sorting device are presented. The differential equation with the initial conditions was solved by numerical methods of "Runge-Kutta-Felberg" with automatic step selection. The components of a …

Conceptual Approaches To Improve Quality Of The Process Of Preparation Energy Personnel For Agricultural Sector Of Economy, A. Radjabov

Irrigation and Melioration

The article highlights problems of training energy personnel for agricultural sector and conceptual, principle and practical approaches to their solution based on goals and objectives outlined in concept of development of higher education system in Uzbekistan until 2030 and Strategy for development of agriculture Republic of Uzbekistan for 2020 - 2030

About Improvement Of Support Of Innovative Activity Of Higher Education By The State, A.E. Norov

Irrigation and Melioration

This article provides information on regulatory acts in support of innovative activities in the field of higher education. It is also indicated that the fact that the scientific activities of universities are not organized based on the prospects for socio-economic development of regions, forecasting innovative development based on analysis and effectiveness of innovations, research results, commercialization of scientific developments, and the involvement of talented youth in research, is the reason for the lack of reliable integration of education, science and production. It is necessary to improve the internal system of competitions, programs and projects aimed at supporting the commercialization of …

Lstm-Based Anomaly Detection For Non-Linear Dynamical System, Yue Tan, Chungjing Hu, Kuan Zhang, Kan Zeng, Ethan A. Davis, Jae Sung Park

Department of Mechanical and Materials Engineering: Faculty Publications

Anomaly detection for non-linear dynamical system plays an important role in ensuring the system stability. However, it is usually complex and has to be solved by large-scale simulation which requires extensive computing resources. In this paper, we propose a novel anomaly detection scheme in non-linear dynamical system based on Long Short-Term Memory (LSTM) to capture complex temporal changes of the time sequence and make multi-step predictions. Specifically, we first present the framework of LSTM-based anomaly detection in non-linear dynamical system, including data preprocessing, multi-step prediction and anomaly detection. According to the prediction requirement, two types of training modes are explored …

Elevate Dental, Connor Merrick, Everett Johnson, Jonah Holbrook

Mechanical Engineering

During a dental procedure, patients are often required to have a bite block placed in their mouths to keep them open for the duration of their procedure. These can be very uncomfortable for patients due to lack of properly-fitting sizes. This project presents an alternative fully adjustable bite block that is affordable, comfortable, and easy to use for dental personnel.The bite block is a two piece side loading design that uses interlocking teeth to supply a range of five sizes.

Design Of A 5 Degree Of Freedom Kinematic Stage For The Dual Crystal Backlighter Imager Diagnostic, Nicholas Nguyen

Master's Theses

The National Ignition Facility (NIF) is home to the world’s most energetic laser. The facility is one of the leading centers in inertial confinement fusion (ICF) experiments to research and understand sustainable fusion energy. To fully document and understand the physics occurring during experiments, precise diagnostics are used for a wide range of purposes. One diagnostic, the crystal backlighter imager (CBI), allows for X-ray imaging of the target at late stages of its implosion.

The aim of this project was to increase the current capabilities of the CBI diagnostic with the addition of a second crystal. This thesis focuses on …

Rsvp Spaceship!, Taylor Chavez, Deven Frauenhofer, Andrew Nott, Zoe Riesen

Mechanical Engineering

This document outlines the Final Design Review of a mechanical engineering senior design project at California Polytechnic State University San Luis Obispo. The project was to design and build a spaceship prop that will deploy during the performance put on by the Sound Design program within the Music Department. This performance, RSVP, is in its 25th year. Dr. Antonio G. Barata, the artistic director and producer of RSVP, is sponsoring the project. The key constraints include keeping the prop hidden in a confined space (under a stage that is comprised of multiple 4 ft. by 8 ft. by 3 ft. …

Design For Additive Manufacturing, Michael Charonnat, Leonardo Franco-Muñoz, Sam Noble, J.P. Purdom

Mechanical Engineering

This document outlines the critical design details and timeline for the Design for Additive Manufacturing Senior Project sponsored by Solar Turbines, Inc. The scope of this project encompasses the redesign of two of Solar Turbine’s cast parts for metal additive manufacturing in order to minimize lead time, cost, and weight. With the overall objective of performing in-depth analysis exploring affordability & feasibility, this redesign process will aid Solar Turbines in expanding their knowledge of Design for Additive Manufacturing principles and enable them to further incorporate the use of additive manufacturing into their production processes. The first part that the team …

California Solar Regatta - Hull Team: Up A Creek, Torrey Duncan, Sean Neuman, Kyle Krietzman, Andrew Offhaus

Mechanical Engineering

The SMUD Solar Regatta competition tasks students with developing a solar-powered watercraft to compete in various events on a fresh water lake. Cal Poly has created two mechanical engineering senior project groups to coordinate the design of a boat for the Solar Regatta competition. Up a Creek, the boat construction team, has created the following Final Design Review document to highlight the group’s progress on the project over the year. This document captures the design process from the background research, project objectives, and early concepts to the final design, manufacturing processes, and planned testing procedures. Unfortunately, the COVID-19 pandemic halted …

Raysun's Infrared Raisin Dryer, Lucas Kensinger, Saraith Aispuro, Joe Vanacore

General Engineering

The RaySuns senior project team was tasked with lowering the drying costs of raisins for River Ranch Raisins. In doing so, we explored several options for cutting costs: utilizing automation and exploring new drying technologies were our primary focus. We eventually planned a modular infrared heating mechanism which would be easy to automate in future projects. After manufacturing and testing an infrared heating mechanism, it was found that infrared drying could significantly cut costs versus the previous natural gas fired dryer tunnels while leaving room for automation. The infrared dryer was also shown to have the potential to create high-quality …

Cp Check Valve Design, Alec B. Der Matoian, Jessica M. Dent, Skylar M. Tusting

Mechanical Engineering

This report is to serve as a final design review and update to the project sponsors at Zurn Wilkins for the Check Valve Design Senior Project. The senior project team was tasked with improving upon the design of Zurn Wilkins’ backflow prevention assembly for small diameter pipes by reducing the pressure loss created by the check valves within the double check backflow assembly. The information contained in this report builds off the information contained in the Critical Design Report (CDR), as well as feedback and further investigation suggested during an Intermediary Design Review. Based on conclusions from the CDR, our …

Atmospheric Water Harvester, Justin K. Lam, Jacob David, Jessica Mabry, Ben Brough

Mechanical Engineering

Atmospheric water harvesting uses the vapor-compression cycle to collect water from the moisture in the air. The system’s components include an evaporator, condenser, compressor, fan, and several expansion valves. Condensate from the air is then funneled into a receptacle, which determines the efficiency of the water harvesting system. For this senior project, the goal is to increase the efficiency of an existing atmospheric water harvester.

Atmospheric Water Harvester, Adam C. Goldstein, Scott Seno, Kristen E. Dentici

Mechanical Engineering

Access to potable water is a global issue that has yet to be adequately solved. In regions with limited access to electricity and ground or surface water, it is not always possible to provide clean water requiring external power or extensive infrastructure to implement. This Final Design Report document will outline the background, design and manufacturing plan involved in the development of a passive atmospheric water harvester. This report builds on the earlier Preliminary Design Review and Critical Design Review documents to reflect further research, analysis, comments from reviewers, and detailed design documentation. While a final design was decided on …

Optical Filter Selector, Camaryn Chambers, Joel Pitzer, Matthew Allen, Callen Schwefler

Mechanical Engineering

One of the many challenges with launching projectiles into space is predicting how the environment in space will affect the trajectory. One way to do this is to look at optical emissions, also known as airglow, which can only be seen from earth with sensitive equipment. By taking measurements of the light from the airglow, properties about the upper atmosphere can be inferred. This is important because variability in the atmosphere can cause variability in space that can affect astronauts and satellites. In order to accomplish this task, optical filters must be used to observe different bands of wavelengths of …

Numerical Methods For Predicting The Dynamic Crushing Response And Energy Absorption Of Composite Aluminum Honeycomb Sandwich Structures, Cody R. Volk

Master's Theses

Edgewise crushing responses of composite aluminum honeycomb sandwich structures were predicted using finite element analysis (FEA) software LS-DYNA by modeling the honeycomb as a material with anisotropic properties. The goal of the project was to develop a process for modeling the sandwich structure to rapidly iterate possible solutions for a safer workstation train table. Current workstation tables are too rigid and may cause injury or death in a head-on collision. Experimental compression tests were used to calibrate the aluminum honeycomb core with material type 26 (MAT 26, honeycomb). A published composite tensile test was used to validate the use of …

Blood Flow Simulation Of Particle Trapping In Models Of Arterial Bifurcations, Qihang Xu

McKelvey School of Engineering Graduate Student Theses & Dissertations

This thesis describes the particle trapping mechanism in blood flow in different arterial bifurcation models. For validation of CFD calculations, a T-junction model and a Y-junction model are analyzed. In both the models, there is one inlet pipe with two outlet pipes creating a symmetric bifurcation at some angle from the centerline of the inlet pipe. Naiver-Stokes (RANS) equations are solved for single phase laminar flow using the commercial CFD software ANSYS Fluent. After validation, Eulerian simulations are performed by using the Discrete Phase Model (DPM) for two-phase flow with particles injected in different bifurcation models with bifurcation angle of …