Other Mechanical Engineering Commons^™

Bellevue-Santa Fe Charter School Solar Panel Project, Dulce Arroyo Martinez, Henrik Lee, Moises Quiroz, Timothy Iafrate

Mechanical Engineering

This project covers the design, manufacture, and installation of solar panel frames on a charter school in Avila Beach, CA. Through preliminary research regarding important factors (such as solar movement, ideal panel angle, and site-specific factors), a frame that meets the standards set forth in the California Building Codes was designed. After approval by presiding authorities, parts specified in the design were ordered, inspected upon arrival, and manufactured to the design as necessary. Much of the challenge was related to the installation aspect of the project—coordination with the proper authorities and correct submission of applications was integral to the success …

Pvc Pipe Longevity Report: Affordability And The 100+ Year Benchmark Standard, Steven Folkman

Mechanical and Aerospace Engineering Faculty Publications

In the United States and Canada, underground water infrastructure was installed during three main time periods because of population growth in the 1800s, 1900–1945, and post 1945. Pipes made of iron constructed in each of these three eras will all start to fail at nearly the same time over the next couple of decades due to the corrosion of the iron pipes. Additionally, the life span of the materials used since the 1960's has changed. Grey cast iron pipes are no longer manufactured and the new ductile iron material has been made thinner to reduce costs, but as a result, …

Asymmetric Unilateral Transfemoral Prosthetic Simulator, Tyagi Ramakrishnan

USF Tampa Graduate Theses and Dissertations

amputation, which includes reduced force generation at the knee and ankle, reduced control of the leg, and different mass properties relative to their intact leg. The physical change in the prosthetic leg leads to gait asymmetries that include spatial, temporal, or force differences. This altered gait can lead to an increase in energy consumption and pain due to compensating forces and torques. The asymmetric prosthesis demonstrated in this research aims to find a balance between the different types of asymmetries to provide a gait that is more symmetric and to make it overall easier for an amputee to walk.

Previous …

Numerical Simulation Of Flow In Ozonation Process, Jie Zhang

USF Tampa Graduate Theses and Dissertations

In the last two decades, Computational Fluid Dynamics (CFD) has shown great potential as a powerful and cost-efficient tool to troubleshoot existing disinfection contactors and improve future designs for the water and wastewater treatment utilities.

In the first part of this dissertation two CFD simulation methodologies or strategies for computing turbulent flow are evaluated in terms of the predicted hydraulic performance of contactors. In the LES (large eddy simulation) methodology, the more energetic, larger scales of the turbulence are explicitly computed or resolved by the grid. In the less computationally intensive RANS (Reynolds-averaged Navier-Stokes) methodology, only the mean component of …

A Sinteractive Ni-Bazr0.8Y0.2O3-Δ Composite Membrane For Hydrogen Separation, Shumin Fang, Siwei Wang, Kyle S. Brinkman, Fanglin Chen

Faculty Publications

BaZr_0.8Y_0.2O_3−δ (BZY) is an excellent candidate material for hydrogen permeation membranes due to its high bulk proton conductivity, mechanical robustness, and chemical stability in H₂O- and CO₂-containing environments. Unfortunately, the use of BZY as a separation membrane has been greatly restrained by its highly refractory nature, poor grain boundary proton conductivity, high number of grain boundaries resulting from limited grain growth during sintering, as well as low electronic conductivity. These problems can be resolved by the fabrication of a Ni–BZY composite membrane with large BZY grains, which requires the development …

Autonomous Indoor Localization For Fire Safety And Resource Location Via Field Mapping Techniques, Jaeyoung Kim, Kartik Ariyur, Yan Cui, Benjamin D. Branch, Joshua Ebung Umo

Libraries Faculty and Staff Presentations

An overall result of this collaboration between the Mechanical Engineering Dept. and the Purdue University Libraries (PUL) should result in building a big data framework that make have knowledge transfer for similar large scale geospatial data implementations. Such may promote best practices of data management where the library skill sets may aid faculty research and student learning. Here, the PUL is concerned with advancing the Mechanical Engineering‘s STEM pipeline capacity with this type of research, collaboration and data management engagement.

Autonomous Indoor Localization For Fire Safety And Resource Location Via Field Mapping Techniques (Android Version), Joshua Ebung Umo, Yan Cui, Kartik Ariyur, Benjamin D. Branch, Jaeyoung Kim

Libraries Faculty and Staff Presentations

An overall result of this collaboration between the Mechanical Engineering Dept. and the Purdue University Libraries (PUL) should result in building a big data framework that make have knowledge transfer for similar large scale geospatial data implementations. Such may promote best practices of data management where the library skill sets may aid faculty research and student learning. Here, the PUL is concerned with advancing the Mechanical Engineering‘s STEM pipeline capacity with this type of research, collaboration and data management engagement.

Team Poly Cup, John Adkins, Scott W. Hart, Elise Kiland

Mechanical Engineering

This project involves the use of mechanical engineering expertise to develop, design, and create a functioning prototype of a collapsible coffee cup. The prototype is to be designed to the specifications given by Jason Blum, the project sponsor. Allowances may be given for design freedom as specified by Jason Blum. The goal of this project is to create a product which may replace the both the disposable coffee cups distributed at coffee shops as well as to create a product which may replace the traditional travel mug due to its increased portability.

Team Poly Cup has worked throughout the year …

Autonomous Indoor Localization Via Field Mapping Techniques, With Agricultural Big Data Application, Yan Cui, Kartik Ariyur, Benjamin D. Branch

Libraries Faculty and Staff Presentations

This joint collaboration between the library, the Mechanical Engineering department shows the current research of localizing an Android smartphone using big data collection and sensor fusion techniques. The original work is Autonomous Indoor Localization via Field Mapping Techniques which primarily designed as indoor fire and safety aid.

For Agricultural Big Data Use, the Android smartphone is being applied to in indoor greenhouse fire, safety and data knowledge design. Such may aid big data tool value to greenhouse fire and safety design and any data that may be important fieldwork considerations.

The indoor agricultural mapping application may be application to greenhouses …

Passive Biaxial Mechanical Properties And In Vivo Axial Pre-Stretch Of The Diseased Human Femoropopliteal And Tibial Arteries, Alexey Kamenskiy, Iraklis I. Pipinos, Yuris A. Dzenis, Clay Lomneth, Syed A. Jaffar Kazmi, Nicholas Y. Phillips, Jason N. Mactaggart

Department of Mechanical and Materials Engineering: Faculty Publications

Surgical and interventional therapies for atherosclerotic lesions of the infrainguinal arteries are notorious for high rates of failure. Frequently, this leads to expensive reinterventions, return of disabling symptoms, or limb loss. Interaction between the artery and repair material likely plays an important role in reconstruction failure, but data describing the mechanical properties and functional characteristics of human femoropopliteal and tibial arteries are currently not available. Diseased superficial femoral (SFA, n=10), popliteal (PA, n=8), and tibial arteries (TA, n=3) from 10 patients with critical limb ischemia were tested to determine passive mechanical properties using planar biaxial extension. All …

Methods, Systems, And Devices For Surgical Access And Inserton, Tom Frederick, Shane Farritor, Jack Mondry, Eric Markvicka, Dmitry Oleynikov, Jacob Greenburg

Department of Mechanical and Materials Engineering: Faculty Publications

The various embodiments herein relate to systems, devices, and/or methods relating to Surgical procedures, and more specifically for accessing an insufflated cavity of a patient and/or positioning Surgical systems or devices into the cavity.

Systemand Method For Controlling Motion Of Spacecrafts, Piyush Grover, Christian Andersson

Department of Mechanical and Materials Engineering: Faculty Publications

A motion of an object is controlled from a geostationary transit orbit (GTO) of an earth to an orbit of a moon. A first trajectory of the motion of the object is determined from an intermediate orbit of an earth to a neighborhood of a stable manifold of a first Lagrange point (L1). A second trajectory of the motion of the object is determined from the GTO to the intermediate orbit. A third trajectory of the motion of the object is determined from the neighborhood to the stable manifold to an L1 orbit, and a fourth trajectory of the motion …

Quality And Safety Of Minimally Invasive Surgery: Past, Present, And Future, Bernadette Mccrory, Chad A. Lagrange, M. S. Hallbeck

Department of Mechanical and Materials Engineering: Faculty Publications

Adverse events because of medical errors are a leading cause of death in the United States (US) exceeding the mortality rates of motor vehicle accidents, breast cancer, and AIDS. Improvements can and should be made to reduce the rates of preventable surgical errors because they account for nearly half of all adverse events within hospitals. Although minimally invasive surgery (MIS) has proven patient benefits such as reduced postoperative pain and hospital stay, its operative environment imposes substantial physical and cognitive strain on the surgeon increasing the risk of error. To mitigate errors and protect patients, a multidisciplinary approach is needed …

Measurement Of Hydrodynamic Force Generation By Swimming Dolphins Using Bubble Dpiv, Frank E. Fish, Paul Legac, Terrie M. Williams, Timothy Wei

Department of Mechanical and Materials Engineering: Faculty Publications

Attempts to measure the propulsive forces produced by swimming dolphins have been limited. Previous uses of computational hydrodynamic models and gliding experiments have provided estimates of thrust production by dolphins, but these were indirect tests that relied on various assumptions. The thrust produced by two actively swimming bottlenose dolphins (Tursiops truncatus) was directly measured using digital particle image velocimetry (DPIV). For dolphins swimming in a large outdoor pool, the DPIV method used illuminated microbubbles that were generated in a narrow sheet from a finely porous hose and a compressed air source. The movement of the bubbles was tracked …

Computational And Experimental Study On Vertical Axis Wind Turbine In Search For An Efficient Design, Mohammad M. Bashar

College of Graduate Studies: Theses & Dissertations

Wind alone can fulfill most of the energy requirement of the world by its efficient conversion in to energy. Though Horizontal Axis Wind Turbine (HAWT) is more popular but needs high wind speed to generate energy. On the other hand Vertical Axis Wind Turbine (VAWT) needs low wind speed and can be installed anywhere which are some of the reasons for this research. The main objective of this research is to improve the design and performance of VAWT to make it more attractive, efficient, durable and sustainable. For a VAWT the blades perform the main role to extract energy from …

Dynamic Fracture Analysis Of Polycarbonate By The Optical Method Of Caustics, Guiyun Gao, Zheng Li, Mehrdad Negahban

Department of Mechanical and Materials Engineering: Faculty Publications

Glassy polycarbonate (PC) is a widely used engineering material in industries, since it has high strength and toughness as well as good transparency. However, these advantages of PC can be suppressed by physical aging, especially its dynamic fracture toughness. In addition, the material properties of PC can be changed dramatically after large plastic compressive deformation, and it can show obvious orthotropic behavior. Here, the combined effect of aging and plastic compressive deformation on dynamic facture of PC was investigated by the optical method of caustics. The dynamic reflective method of caustics for orthotropic materials was developed here to study the …

Simulations And Measurements Of Fuel Film Using Refractive Index Matching Method, Fengkun Wang

Wayne State University Theses

ABSTRACT

SIMULATIONS AND MEASUREMENTS OF FUEL FILM USING REFRACTIVE INDEX MATCHING METHOD

by

FENGKUN WANG

APRIL 2014

Advisor: Dr. Ming-Chia Lai

Major: Mechanical Engineering

Degree: Master of Science

Direct Injection (DI) has been known for its improved performance and efficiency in gasoline spark-ignition engines. However, wall wetting is inevitable and the source of UHC and PM. In order to take advantage of the GDI technology, it is important to investigate spray wall interactions in detail.

Numerical and experimental studies are carried out for spray and wall impingements in an optical constant volume vessel. The fuel film was measured spatially and …

Test 2082: John Deere 7210r, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2097: New Holland T9.565, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2093a: New Holland T9.480, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2100: John Deere 8295r, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2096: Case Ih Steiger 540, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2094a: New Holland T9.530, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2088: Challenger Mt765e, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2093: Case Ih Steiger 420, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2092: Case Ih Steiger 370, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2089: Challenger Mt775e, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2091: John Deere 7290r, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2104a: Challenger Mt575d Ap6, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2104: Massey Ferguson 7622 Dyna 6, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …