Other Mechanical Engineering Commons^™

Environmental Damage Caused By Transport Equipment Waste, M. Radkevich, K. Shipilova, M. Abdukodirova, O. Pochugevski

Irrigation and Melioration

The article suggests a new approach to the monetary assessment of the damage caused to the environment by the processed waste of the transport sector. The proposed assessment method is based on the waste collection factor, all types of irretrievable losses and the volume of necessary compensatory release of materials. Based on a survey among vehicle owners, it was found that the solid waste collection rate is about 50 %, while the waste collection rate for operating fluids does not exceed 32 %. In this regard, the bulk of the damage to the environment is caused by liquid waste. Calculations …

Research Of Stress-Deformed State Of Multi-Connected Complex Shell Structures, Т.М. Маvlanov, Sh.O. Khudainazarov, B. Yalgashev, O.S. Nurova

Irrigation and Melioration

Conducting numerical experiments for complex structurally inhomogeneous structures allows us to understand the qualitative picture of the effect of various parameters in a wide range of studies and to give sound recommendations at the design stage for conducting laboratory model and field experiments. In this paper, on the basis of the classical theory of elasticity, the basic equations characterizing the stress-strain state of complex multiply connected shell structures are given and a specific problem is solved. At the same time, some of the structural elements have viscoelastic properties. When solving the problem, the behavior of the structure for the n-th …

To The Determination Of The Critical Circuit Speed Of The Sharing Drum, Kh. Kh. Igamberdiev, A.B. Mukhitdinov

Irrigation and Melioration

The article is devoted to the theoretical definition of the critical circumferential speed of the stripping drum of a kena harvester, which depends on the drum diameter, diameter and weight of the stems. It was determined from the equality of the change in the momentum of the stem during impact, i.e. from a shock impulse acting on the stem. The shock impulse is determined when the drum blade touches the stem in the process of stripping, which acts on the mass of the entire stem. The duration of the impact of the drum stripping on the stem was determined from …

An Innovative Seeder For Sowing Non-Loose Seeds Of Saxaul And Cherkez, E.T. Farmonov

Irrigation and Melioration

The main reasons for the absence of a seeder for mechanized sowing of non-loose seeds of fodder plants in deserts are analyzed in the article. The author has developed a technology for sowing non-loose seeds (saxaul and cherkez), which prevents clogging, crushing and breakage in the seeder hopper, and provides for uniform and stable sowing at a set rate and shallow depth over the entire field area without reducing the biological germination. An innovative seeder with a universal sowing unit is recommended. Field tests of the innovative seeder with the proposed universal sowing unit were conducted in February 2020, as …

Recommendations For The Analysis And Safety Assessment Of Turbid Sediments In Flood Reservoirs, А. Yangiev, Sh. Panjiev, D. Adjimuradov

Irrigation and Melioration

The article presents the results of field research conducted in Langar, Dehkanabad, Shurabsoy flood reservoirs in the Kashkadarya region.There are many problems as a result of floods in the reservoirs, there are disturbances in the discharge and drainage facilities during the passage of accidental floods.At the same time, there was a large accumulation of turbid-sediments in flood reservoirs.In the article, the results of the calculations using empirical formulas for predicting the amount of turbid sediments in Langar, Dehkanabad, Shurabsoy flood reservoirs up to 2025-2030 years are also presented, and it is noted that at present their useless volumes are full …

Justification Of Parameters Of Replaceable Working Parts Of A Combined Machine, А.A. Akhmetov, L.B. Muratov

Irrigation and Melioration

In article are described the design and options for completing the replaceable working parts of the combined machine for continuous tillage which of the formation of ridges and ridges for sowing re-crops. The parameters of the ridge former and apron-leveler of this machine have been substantiated. The rational values of the parameters of the comb-former are: length 600 mm, width of the entrance edge 680 mm, height of the blade 160 mm, length of the side edge of the blade 178 mm. The rational values of the working length and height of the leveling apron are 220 mm and 200 …

Development Of An Algorithm For Optimization Of Continuous Technological Process Of Cultivation Of Microorganisms, Sh.R. Rakhmanov

Irrigation and Melioration

In article the analysis of possible modes of microalgae cultivation has been carried out. Two optimization algorithms are substantiated. The first one is based on the method of random search with an absolute bias, an algorithm for optimizing the process of cultivating microorganisms with continuous regeneration of the flow in one cultivator. The second is an algorithm for determining the optimal residence time of chlorella particles in multistage cultivators, focused on the method of dynamic programming, implemented in Wellman's recurrence relation. The developed algorithm for operational forecasting and automatic control of the chlorella cultivation process allows, under given production conditions …

Covid-19 Impact To Family Food Consumption And Income In Uzbekistan: Results Of An Online Survey, Kh. Pardaev, Sh. Hasanov, S. Mamasoliev, Sh. Muratov, R. Kalandarov, U. Nurullaev

Irrigation and Melioration

This article aims to study the impact of the pandemic on food consumption by families in Uzbekistan. The shock of the pandemic is threatening the well-being of families in Uzbekistan, as in all developing countries. The study focuses on the effects of changes in food prices, declining consumption, and changes in household incomes. The Instrumental regression model was used in the factor impact analysis. Data for analysis were collected online by messenger groups from families in urban and rural areas of Uzbekistan. Results of the Econometric analysis demonstrated that the decline in food consumption in households was assessed by a …

Status Of Crop Diversification And Its Empirical Analysis: A Case Study Of The Republic Of Uzbekistan, A.E. Primov

Irrigation and Melioration

The main objective of this study is to determine the status and level of crop diversification among farms in the country through an empirical analysis using panel data collected in 2009-2017. In doing so, we performed the Stata-16 software using the Simpson Diversification Index model in determining the diversification index. According to the results, the highest diversification indicators were found for Samarkand, Fergana and Tashkent regions, respectively, and accounted for 0.74, 0.74 and 0.76, respectively. It can be seen that the existing farms in Tashkent region used more diversified crops than in other regions of the country. The average diversification …

Efficiency Of Using Graphic Software In The Design Of Hydrotechnical Structures, U.A. Nasritdinova, A.M. Khodjaev, Z.I. Kayumova

Irrigation and Melioration

The article examines the work of scientists engaged in research in this area in the design of hydrotechnic structures. The possibilities of design programs for the application of the results of scientific research in the educational process were used. Thanks to the design in these programs, practical tasks are carried out with the utmost precision. The use of computer technology in teaching the subject "Hydrotechnical structures" and the use of graphic software AutoCAD in the design of linear platforms for clothing, curved platforms for clothing from hydrotechnical structures are shown in 2D and 3D three-dimensional modeling.

Modulation Of Mechanical Stress Mitigates Anti-Dsg3 Antibody-Induced Dissociation Of Cell–Cell Adhesion, Xiaowei Jin, Jordan Rosenbohm, Eunju Kim, Amir Monemian Monemianesfahani, Kristina Seiffert-Sinha, James K. Wahl Iii, Jung Yul Lim, Animesh A. Sinha, Ruiguo Yang

Department of Mechanical and Materials Engineering: Faculty Publications

It is becoming increasingly clear that mechanical stress in adhesive junctions plays a significant role in dictating the fate of cell–cell attachment under physiological conditions. Targeted disruption of cell–cell junctions leads to multiple pathological conditions, among them the life-threatening autoimmune blistering disease pemphigus vulgaris (PV). The dissociation of cell–cell junctions by autoantibodies is the hallmark of PV, however, the detailed mechanisms that result in tissue destruction remain unclear. Thus far, research and therapy in PV have focused primarily on immune mechanisms upstream of autoantibody binding, while the biophysical aspects of the cell– cell dissociation process leading to acantholysis are less …

Modulation Of Mechanical Stress Mitigates Anti-Dsg3 Antibody-Induced Dissociation Of Cell–Cell Adhesion, Xiaowei Jin, Jordan Rosenbohm, Eunju Kim, Amir Monemian Esfahani, Kristina Seiffert-Sinha, James K. Wahl Iii, Jung Yul Lim, Animesh A. Sinha, Ruiguo Yang

Department of Mechanical and Materials Engineering: Faculty Publications

It is becoming increasingly clear that mechanical stress in adhesive junctions plays a significant role in dictating the fate of cell–cell attachment under physiological conditions. Targeted disruption of cell–cell junctions leads to multiple pathological conditions, among them the life-threatening autoimmune blistering disease pemphigus vulgaris (PV). The dissociation of cell–cell junctions by autoantibodies is the hallmark of PV, however, the detailed mechanisms that result in tissue destruction remain unclear. Thus far, research and therapy in PV have focused primarily on immune mechanisms upstream of autoantibody binding, while the biophysical aspects of the cell– cell dissociation process leading to acantholysis are less …

Common Pool Resource Management: Assessing Water Resources Planning For Hydrologically Connected Surface And Groundwater Systems, Francisco Munoz-Arriola, Tarik Abdel-Monem, A. Amaranto

Department of Mechanical and Materials Engineering: Faculty Publications

Common pool resource (CPR) management has the potential to overcome the collective action dilemma, defined as the tendency for individual users to exploit natural resources and contribute to a tragedy of the commons. Design principles associated with effective CPR management help to ensure that arrangements work to the mutual benefit of water users. This study contributes to current research on CPR management by examining the process of implementing integrated management planning through the lens of CPR design principles. Integrated management plans facilitate the management of a complex common pool resource, ground and surface water resources having a hydrological connection. Water …

Part-Scale Thermal Simulation Of Laser Powder Bed Fusion Using Graph Theory: Effect Of Thermal History On Porosity, Microstructure Evolution, And Recoater Crash, Reza Yavari, Ziyad Smoqi, Alex Riensche, Ben Bevans, Humaun Kobir, Heimdall Mendoza, Hyeyun Song, Kevin Cole, Prahalada Rao

Department of Mechanical and Materials Engineering: Faculty Publications

Flaw formation in laser powder bed fusion (LPBF) is influenced by the spatiotemporal temperature distribution – thermal history – of the part during the process. Therefore, to prevent flaw formation there is a need for fast and accurate models that can predict the thermal history as a function of the part shape and processing parameters. In previous work, a thermal modeling approach based on graph theory was used to predict the thermal history in LPBF parts in less-than 20% of the time required by finite element-based models with error within 10% of experimental measurements. The present work transitions toward the …

Chilling And Heat Accumulation Of Fruit And Nut Trees And Flower Bud Vulnerability To Early Spring Low Temperatures In New Mexico: Meteorological Approach, Koffi Djaman, Komlan Koudahe, Murali Darapuneni, Suat Irkmak

Department of Mechanical and Materials Engineering: Faculty Publications

Fruit and nut trees production is an important activity across the southwest United States and this production is greatly impacted by the local climate. Temperature is the main environmental factor influencing the growth and the productivity of the fruit and nut trees as it affects the trees’ physiology and the vulnerability of flower bud, flowers, and young fruit and nut to the low temperatures or spring frost. The objective of the present study is to estimate the chilling and heat accumulation of fruit and nut trees across New Mexico. Three study sites as Fabian Garcia, Los Lunas, and Farmington were …

Characterization Of The Strain-Rate–Dependent Mechanical Response Of Single Cell–Cell Junctions, Amir Monemian Esfahani, Jordan Rosenbohm, Bahareh Tajvidi Safa, Nickolay V. Lavrik, Grayson Minnick, Quan Zhou, Fang Kong, Xiaowei Jin, Eunju Kim, Ying Liu, Yongfeng Lu, Jung Yul Lim, James K. Wahl Iii, Ming Dao, Changjin Huang, Ruiguo Yang

Department of Mechanical and Materials Engineering: Faculty Publications

Cell–cell adhesions are often subjected to mechanical strains of different rates and magnitudes in normal tissue function. However, the rate-dependent mechanical behavior of individual cell– cell adhesions has not been fully characterized due to the lack of proper experimental techniques and therefore remains elusive. This is particularly true under large strain conditions, which may potentially lead to cell–cell adhesion dissociation and ultimately tissue fracture. In this study, we designed and fabricated a single-cell adhesion micro tensile tester (SCAμTT) using twophoton polymerization and performed displacement-controlled tensile tests of individual pairs of adherent epithelial cells with a mature cell–cell adhesion. Straining the …

Irrigation Management In Potato (Solanum Tuberosum L.) Production: A Review, Koffi Djaman, Suat Irkmak, Komlan Koudahe, Samuel Allen

Department of Mechanical and Materials Engineering: Faculty Publications

Limited water resources coupled with the increase of the human population calls for more efficient use of water in irrigated agriculture. Potato (Solanum tuberosum L.) is one of the most widely grown crops worldwide and is very sensitive to water stress due to its shallow rooting system. With the dilemma of potato sensitivity to drought and limited available water resources restricting crop production, researchers and crop growers have been investigating different approaches for optimizing potato yield and improving crop water use efficiency under different irrigation methods. While potato response to water is affected by other management practices such as fertilizer …

Ultrasonic Mapping Of Hybrid Additively Manufactured 420 Stainless Steel, Luz D. Sotelo, Haitham Hadidi, Cody S. Pratt, Michael P. Sealy, Joseph A. Turner

Department of Mechanical and Materials Engineering: Faculty Publications

Metal hybrid additive manufacturing (AM) processes are suitable to create complex structures that advance engineering performance. Hybrid AM can be used to create functionally graded materials for which the variation in microstructure and material properties across the domain is created through a synergized combination of fully coupled manufacturing processes and/or energy sources. This expansion in the engineering design and manufacturing spaces presents challenges for nondestructive evaluation, including the assessment of the sensitivity of nondestructive measurements to functional gradients. To address this problem, linear ultrasound measurements are used to interrogate 420 stainless steel coupons from three manufacturing methods: wrought, AM, and …

Unveiling Precipitation Behavior In Mg-Y Based Alloys, Qingchun Zhu, Yangxin Li, Zhigang Ding, Jian Wang, Yuxuan Liu, Huan Zhang, Tian Xie, Mingxu Wang, Hong Zhu, Tao Ying, Wei Liu, Xiaoquin Zeng

Department of Mechanical and Materials Engineering: Faculty Publications

Mg-Y based alloys exhibit a promising combination of strength and deformability through tuning precipitation and solute strengthening mechanisms and tailoring the activity of non-basal dislocations. Understanding the precipitation sequence of Mg-Y based alloys and its dependence on Yttrium concentration in the matrix will provide a guideline for fine tuning structure, morphology and distribution of precipitates in Mg-Y based alloys. In this paper, we explore the precipitation behaviors of Mg-11Y (wt%) and Mg-11Y-1Al (wt%) alloys using aberration-corrected scanning transmission electron microscopy, and rationalize the experimental observations based on first-principles density functional theory calculations. The precipitation sequence during ageing at 225 °C …

The Role Of Microenvironmental Cues And Mechanical Loading Milieus In Breast Cancer Cell Progression And Metastasis, Brandon D. Riehl, Eunju Kim, Tasneem Bouzid, Jung Yul Lim

Department of Mechanical and Materials Engineering: Faculty Publications

Cancer can disrupt the microenvironments and mechanical homeostatic actions in multiple scales from large tissue modification to altered cellular signaling pathway in mechanotransduction. In this review, we highlight recent progresses in breast cancer cell mechanobiology focusing on cell-microenvironment interaction and mechanical loading regulation of cells. First, the effects of microenvironmental cues on breast cancer cell progression and metastasis will be reviewed with respect to substrate stiffness, chemical/topographic substrate patterning, and 2D vs. 3D cultures. Then, the role of mechanical loading situations such as tensile stretch, compression, and flow-induced shear will be discussed in relation to breast cancer cell mechanobiology and …

Quantification Of Nitric Oxide Concentration Using Single-Walled Carbon Nanotube Sensors, Jakob Meier, Joseph Stapleton, Eric M. Hofferber, Abigail Haworth, Stephen D. Kachman, Nicole M. Iverson

Department of Mechanical and Materials Engineering: Faculty Publications

Nitric oxide (NO), a free radical present in biological systems, can have many detrimental effects on the body, from inflammation to cancer. Due to NO’s short half-life, detection and quantification is difficult. The inability to quantify NO has hindered researchers’ understanding of its impact in healthy and diseased conditions. Single-walled carbon nanotubes (SWNTs), when wrapped in a specific single-stranded DNA chain, becomes selective to NO, creating a fluorescence sensor. Unfortunately, the correlation between NO concentration and the SWNT’s fluorescence intensity has been difficult to determine due to an inability to immobilize the sensor without altering its properties. Through the use …

Mechanical Behavior Of Al–Al2cu–Si And Al–Al2cu Eutectic Alloys, Qian Lei, Jian Wang, Amitava Mitra

Department of Mechanical and Materials Engineering: Faculty Publications

In this study, laser rapid solidification technique was used to refine the microstructure of ternary Al–Cu–Si and binary Al–Cu eutectic alloys to nanoscales. Micropillar compression testing was performed to measure the stress–strain response of the samples with characteristic microstructure in the melt pool regions. The laser-remelted Al–Al₂Cu–Si ternary alloy was observed to reach the compressive strength of 1.59 GPa before failure at a strain of 28.5%, which is significantly better than the as-cast alloy with a maximum strength of 0.48 GPa at a failure strain of 4.8%. The laser-remelted Al–Cu binary alloy was observed to reach the compressive …

Sensitive X-Ray And Gamma-Ray Detectors Including Perovskite Single Crystals, Jinsong Huang, Haotong Wei

Department of Mechanical and Materials Engineering: Faculty Publications

Perovskite single crystal X-ray and gamma-ray radiation detector devices include an X-ray and gamma-ray wavelength responsive active layer including a perovskite single crystal. The perovskite single crystal is a perovskite single crystal having a structure of ABX₃ , wherein A is methyl ammonium ( CH₂NH₂+), C_S+, formamidinum ( H₂NCHNH₂+) , or Rb⁺ or a mixture thereof, B is Pb²⁺ which can be partially or completely replaced by other ions including Bi³⁺, Sb³⁺, Sn²⁺ or a mixture thereof, and X is a halide …

Use Of Energy Consumption During Milling To Fill A Measurement Gap In Hybrid Additive Manufacturing, K. L. M. Avegnon, P. Noll, M. R. Uddin, G. Madireddy, R. Williams, A. Achuthan, M. P. Sealy

Department of Mechanical and Materials Engineering: Faculty Publications

Coupling additive manufacturing (AM) with interlayer peening introduces bulk anisotropic properties within a build across several centimeters. Current methods to map high resolution anisotropy and heterogeneity are either destructive or have a limited penetration depth using a nondestructive method. An alternative pseudo-nondestructive method to map high-resolution anisotropy and heterogeneity is through energy consumption during milling. Previous research has shown energy consumption during milling correlates with surface integrity. Since surface milling of additively manufactured parts is often required for post-processing to improve dimensional accuracy, an opportunity is available to use surface milling as an alternative method to measure mechanical properties and …

Electrostatic Flocking Of Salt-Treated Microfibers And Nanofiber Yarns For Regenerative Engineering, Alec Mccarthy, Kossi Loic M. Avegnon, Phil A. Holubeck, Demi Brown, Anik Karan, Navatha Shree Sharma, Johnson V. John, Shelbie Weihs, Jazmin Ley, Jingwei Xie

Department of Mechanical and Materials Engineering: Faculty Publications

Electrostatic flocking is a textile technology that employs a Coulombic driving force to launch short fibers from a charging source towards an adhesive-covered substrate, resulting in a dense array of aligned fibers perpendicular to the substrate. However, electrostatic flocking of insulative polymeric fibers remains a challenge due to their insufficient charge accumulation. We report a facile method to flock electrostatically insulative poly(ε-caprolactone) (PCL) microfibers (MFs) and electrospun PCL nanofiber yarns (NFYs) by incorporating NaCl during preflock processing. Both MF and NFY were evaluated for flock functionality, mechanical properties, and biological responses. To demonstrate this platform's diverse applications, standalone flocked NFY …

A Method Of Identifying Allographs In Undeciphered Scripts And Its Application To The Indus Valley Script, Shruti Daggumati, Peter Revesz

Department of Mechanical and Materials Engineering: Faculty Publications

This work describes a general method of testing for redundancies in the sign lists of ancient scripts by data mining the positions of the signs within the inscriptions. The redundant signs are allographs of the same grapheme. The method is applied to the undeciphered Indus Valley Script, which stands out from other ancient scripts by having a large proposed sign list that contains dozens of asymmetric signs that have mirrored pairs. By a statistical analysis of mirrored asymmetric signs, this paper shows that the Indus Valley Script was multi-directional and the mirroring of signs often denotes only the direction of …

Metallic Surface Doping Of Metal Halide Perovskites, Yuze Lin, Yuchuan Shao, Jun Dai, Tao Li, Yi Liu, Xuezeng Dai, Xun Xiao, Yehao Deng, Alexei Gruverman, Xiao Cheng Zeng, Jinsong Huang

Department of Mechanical and Materials Engineering: Faculty Publications

Intentional doping is the core of semiconductor technologies to tune electrical and optical properties of semiconductors for electronic devices, however, it has shown to be a grand challenge for halide perovskites. Here, we show that some metal ions, such as silver, strontium, cerium ions, which exist in the precursors of halide perovskites as impurities, can n-dope the surface of perovskites from being intrinsic to metallic. The low solubility of these ions in halide perovskite crystals excludes the metal impurities to perovskite surfaces, leaving the interior of perovskite crystals intrinsic. Computation shows these metal ions introduce many electronic states close to …

Recurrence Network Analysis Of Design-Quality Interactions In Additive Manufacturing, Ruimin Chen, Prahalada K. Rao, Yan Lu, Edward W. Reutzel, Hui Yang

Department of Mechanical and Materials Engineering: Faculty Publications

Powder bed fusion (PBF) additive manufacturing (AM) provides a great level of flexibility in the design-driven build of metal products. However, the more complex the design, the more difficult it becomes to control the quality of AM builds. The quality challenge persistently hampers the widespread application of AM technology. Advanced imaging (e.g., X-ray computed tomography scans and high-resolution optical images) has been increasingly explored to enhance the visibility of information and improve the AM quality control. Realizing the full potential of imaging data depends on the advent of information processing methodologies for the analysis of design-quality interactions. This paper presents …

Process-Structure Relationship In The Directed Energy Deposition Of Cobalt-Chromium Alloy (Stellite 21) Coatings, Ziyad M. Smoqi, Joshua Toddy, Harold (Scott) Halliday, Jeffrey E. Shield, Prahalada K. Rao

Department of Mechanical and Materials Engineering: Faculty Publications

In this work, we accomplished the crack-free directed energy deposition (DED) of a multi-layer Cobalt- Chromium alloy coating (Stellite 21) on Inconel 718 substrate. Stellite alloys are used as coating materials given their resistance to wear, corrosion, and high temperature. The main challenge in DED of Stellite coatings is the proclivity for crack formation during printing. The objective of this work is to characterize the effect of the input energy density and localized laser-based preheating on the characteristics of the deposited coating, namely, crack formation, microstructural evolution, dilution of the coating composition due to diffusion of iron and nickel from …

Test-Retest Reliability And Minimal Detectable Change Of The Computerized Dynamic Posturography Proprio For Adults With Chronic Traumatic Brain Injury, Guilherme Manna Cesar, Thad W. Buster, Judith M. Burnfield

Department of Mechanical and Materials Engineering: Faculty Publications

Purpose: Balance deficits after brain injury, including reactive recovery from unexpected perturbations, can persist well after rehabilitation is concluded. While traditional clinical assessments are practical, the anticipatory nature of the tasks may mask perceptible balance control. Computerized dynamic posturography can directly quantify capacity to respond to unexpected, external perturbations. This study examined the reliability of the computerized dynamic posturography assessment with the device PROPRIO® 4000 in adults with traumatic brain injury and created the minimal detectable change for its standardized test.

Methods: Ten adults (ages 21–55 years) with chronic (average 10 ± 6 years post-injury) severe (loss of consciousness 2–75 …