Other Mechanical Engineering Commons^™

Investigation Of Two-Phase Flow Phenomena In Rotating Paper Dryer To Achieve Effective Heat Transfer With Low Energy Consumption, Hamed Abdul Majeed

LSU New Orleans Theses and Dissertations

The paper industry provides important consumer products comprised of paper, tissue, paper board, and pulping. The papermaking process requires a lot of energy, in the form of steam, to dry the paper web in rotating dryers. As steam condenses inside the dryers by releasing heat to the dryer walls, the condensate is removed using either stationary or rotary siphons. Since the condensate is usually at a saturated state, part of the condensate flashes into vapor during the extraction process and becomes difficult to extract. Thus, additional blow-through steam is used to push the condensate out. Since this blow-through steam is …

Desalination For Sustainable Water Production With An Emphasis On Low Pressure Distillation, Jessica Vivian Savage

Doctoral Dissertations and Master's Theses

Freshwater resources depletion is a growing concern. This freshwater scarcity motivates research into seawater desalination as a means for alleviating the stresses on water demands. The primary methods of desalination include filtration and distillation. This paper explores the potential energy savings of vacuum distillation for seawater desalination to reduce the amount of energy needed to achieve phase change.

Depending on the vacuum boiler design, the vaporization mechanism may be boiling, evaporation, or cavitation. There is very little literature on cavitation that involves mass transfer, so cavitation is not developed here. This thesis focuses on standard models for boiling and evaporation …

A Road Grade Based Weighting System For Calculating On-Road Distance-Specific Oxides Of Nitrogen Emissions Of Light-Duty Diesel Vehicles, Jason D. Bolyard

Graduate Theses, Dissertations, and Problem Reports (ETD)

Light-duty diesel vehicles have received significant public and governmental scrutiny recently for violating emissions regulations. Similar to the heavy-duty diesel manufacturers during the late 1990’s, some light-duty manufacturers were implementing different control strategies between laboratory certification tests and customer on-road operation. These devices allowed the vehicle to pass certification tests but then use alternative operation on the road during normal use. The alternative operation would allow for better fuel economy but higher oxides of nitrogen (NOx) emissions. Light-duty vehicles are currently certified in the US using chassis dynamometer testing. The effects of all on-road driving conditions are not mimicked in …

Entertainment 721, Mark Hendricks, Noah John, Jadon Vanyo, Chelsea Payne

Williams Honors College, Honors Research Projects

The goal of this project was to design a luxury, aesthetically pleasing entertainment system with a TV lift mechanism that could be remote controlled. The design would also include a cooling cabinet for gaming systems, a remote locking system, and additional storage. Using a morphological chart and weighted decision matrix for each subsystem key features were determined to be included in the design. Several performance benchmarks were determined to accomplish the team’s design. Almost every benchmark was successful in the build of the first prototype. Several heat calculations and FEA analyses were performed on the system to ensure the success …

Torrefaction Of Mixed Solid Waste, Zhuo Xu

Dissertations, Master's Theses and Master's Reports

The world is witnessing unprecedented accumulation of solid wastes in the environment and landfills with well-documented ecological, environmental, health, and economic consequences. With population growth and rise in living standards, solid wastes generation will increase, making the issue more pressing. In addition, current practices of solid waste disposal are creating an immediate challenge and a long-term disaster-scale problem. The solid wastes comprises two main groups of materials: (i) fiber wastes (paper, food, wood, trimming, 61% of U.S. municipal solid waste) and (ii)uniquely challenging subset of plastic wastes (13%) that become a threat to global sustainability including dangers to marine and …

Performance And Economical Analysis Of Different Insulating Materials Used To Reduce The Heat Load Of An Existing Residential Building, Radwa A. El-Awadly, Ahmed A. Abdel-Rehim

Mechanical Engineering

The energy consumption from the residential sector is an important element which has an impact on the total energy consumption in any country. The heating and air conditioning loads can be reduced through many means. Using thermal insulation in buildings does not only contribute in reducing the required air conditioning system size, but also in reducing the annual energy cost for the whole building. In this case, the energy saving varies according to the building type, the climatic conditions at which the building is located as well as the type of the insulating material used. In the present study, an …

Investigating Nox Vs Co2 Tradeoff In Heavy Duty Emissions Through The Years Under The Scope Of Carb’S 3-Bin Moving Average Window Method, Ghadi Sadek

Graduate Theses, Dissertations, and Problem Reports (ETD)

With the rise in urban pollution level over the last few years, regulatory agencies around the world have taken multiple steps to ensure engine exhaust pollutant are well monitored and properly regulated. Yet there exists a significant difference in emissions rates in various operating conditions between US and European products which currently uses a Moving average window (MAW) approach for their in-use compliance testing and certification program. Using WVU’s vehicle data collected using PEMS devices, this study aims at investigating the NOx versus CO2 tradeoff found in heavy duty diesel engines equipped with different aftertreatment technologies, under the scope of …

Performance Improvements For Next Generation Falling Particle Receiver Systems, Nathan R. Schroeder

Mechanical Engineering ETDs

Falling particle receiver (FPR) systems are a rapidly developing technology for concentrating solar power applications. Solid particles are used as both the heat transfer fluid and thermal energy storage media. Through the direct solar irradiation of the solid particles, flux and temperature limitations of tube-bundle receives can be overcome leading to higher operating temperatures and energy conversion efficiencies. Particle residence time, curtain opacity, and curtain stability affect the performance of FPR designs. As the particles fall through the receiver the curtain accelerates, increasing its transmissivity thus decreasing the amount of energy absorbed. Multistage release trough structures catch and release the …

Kinetic Study Of In-Pipe Water Flow For Power Generation, Surendaran Venuthan

Student Works (2020-2029)

In-pipe turbine generator has a potential to harvest energy from an existing water flow from distribution pipe which have natural and pumping capacity. That flow will be used to convert kinetic energy from the pipe to rotate the turbine. In turn, the turbine may be connected to a generator to produce electric power. The fact that the in-pipe turbine generator will be a useful energy harvesting tool with potential with industrial application is recommended by many scholars. However, there is a concern where there are many types and sizes of pipe that is readily used in the water works industry. …

Design For Additive Manufacturing, Michael Charonnat, Leonardo Franco-Muñoz, Sam Noble, J.P. Purdom

Mechanical Engineering

This document outlines the critical design details and timeline for the Design for Additive Manufacturing Senior Project sponsored by Solar Turbines, Inc. The scope of this project encompasses the redesign of two of Solar Turbine’s cast parts for metal additive manufacturing in order to minimize lead time, cost, and weight. With the overall objective of performing in-depth analysis exploring affordability & feasibility, this redesign process will aid Solar Turbines in expanding their knowledge of Design for Additive Manufacturing principles and enable them to further incorporate the use of additive manufacturing into their production processes. The first part that the team …

Raysun's Infrared Raisin Dryer, Lucas Kensinger, Saraith Aispuro, Joe Vanacore

General Engineering

The RaySuns senior project team was tasked with lowering the drying costs of raisins for River Ranch Raisins. In doing so, we explored several options for cutting costs: utilizing automation and exploring new drying technologies were our primary focus. We eventually planned a modular infrared heating mechanism which would be easy to automate in future projects. After manufacturing and testing an infrared heating mechanism, it was found that infrared drying could significantly cut costs versus the previous natural gas fired dryer tunnels while leaving room for automation. The infrared dryer was also shown to have the potential to create high-quality …

The Development Of All Solid-State Optical Cryo-Cooler, Junwei Meng

Optical Science and Engineering ETDs

This dissertation describes the development of an all solid-state optical cryo-cooler. Crystals of 10% wt. ytterbium-doped yttrium lithium fluoride (Yb³⁺:YLF) are used to cool an infrared HgCdTe sensor payload to an absolute temperature below 135 K, equivalent to delta T equal 138 K below ambient. This record level of cooling is accomplished with a single stage, in a completely vibration-free environment, with a corresponding cooling power of 190 mW. This milestone is made possible by the design and fabrication of an undoped YLF thermal link that efficiently shields the payload with a non-right angle kink from intense anti-Stokes …

Emissivity Measurements Of Painted And Aerosol Deposited Thermographic Phosphors (Yag:Dy And Mfg:Mn), Wendy Flores-Brito

Mechanical Engineering ETDs

Combustion is one of the most difficult processes to model. Luminous flames are characteristically sooty, which creates a problem when modeling and calculating the combustion and heat transfer of the process; both of which are highly dependent on temperature and emissivity. Soot particle emissivity as well as gas contributions affect the heat transfer calculation and must be accounted for.

Thermographic phosphors (TP) are ceramic based phosphorescent materials that have a temperature dependent emission that can be exploited to obtain surface and gas temperature measurements, as well as 2D temperature maps. Emissivity knowledge is not needed to obtain temperature and is …

Adaptable Clean Energy Laboratory, Joao Marcelo Rocha Belmonte, Marc D. Compere

Sustainability Conference

The Adaptable Clean Energy (ACE) Lab is a real-world, long term, test platform that will guide the courses of the Energy Systems track. The lab will provide realistic electrical and HVAC loads that mimic a solar powered office. The lab is a 20’ high cube shipping container modified with a door, windows, lights computers, air conditioner and appliances. The lab is Net-Zero and powered entirely from the sun. Two insulation test sections expose the exterior walls for research access to real external heat loads in a real building

Development Of An Activity-Based Windowing Approach To Evaluate Real-World Nox Emissions From Modern Medium And Heavy-Duty Diesel Trucks, Rasik Pondicherry

Graduate Theses, Dissertations, and Problem Reports (ETD)

The introduction of in-use emissions regulations by the United States Environmental Protection Agency (U.S.EPA) requires medium-duty (MD) and heavy-duty (HD) engine manufacturers to demonstrate emissions compliance during in-fleet operation. In the United States (U.S.), the Not-to-Exceed (NTE) method is used to evaluate real-world emissions compliance from on-highway MD and HD trucks. Regulatory agencies, engine manufacturers and research entities have identified that the NTE method incorporates numerous exclusions and evaluates emissions compliance only under selective operating conditions that are favorable for the selective catalytic reduction (SCR) system to reduce oxides of nitrogen (NOx) emissions efficiently. Such operation is typically encountered only …

Vaccine Cooler For The Global Poor, Benjamin J. Larson, Cooper E. Gibson, Eilbron Younan, Cody R. Volk

Mechanical Engineering

Cal Poly physics professors Peter Schwartz and Nathan Heston approached the Solar Freeze team with the problem that remote communities in Africa have limited access to modern-day medicine or vaccines. They suggested that we try and design a cooling device that can keep vaccines cold for multiple days at a time while the medicine is transported to remote villages. Currently, there are vaccine cooler products on the market, but most of them are very expensive or lack portability. Peter and Nate have tasked the Solar Freeze team to come up with a less expensive solution that is also portable and …

Influence Of Micro-Nucleate Boiling On Annular Flow Regime Heat Transfer Coefficient Values And Flow Parameters – For High Heat-Flux Flow Boiling Of Water, Soroush Sepahyar

Dissertations, Master's Theses and Master's Reports

Analysis of results from steady and steady-in-the-mean high heat-flux (15 - 70 W/cm², with water as working fluid) shear driven annular flow-boiling experiments presented here - and low heat-flux (0.1- 1 W/cm², with FC-72 as working fluid) experiments presented elsewhere – together lead to a key conclusion. The conclusion is that heat carrying nucleation rates go often undetected by the typically used visualization approaches for flow boiling – as such flows often involve µm- to sub- µm scale bubble diameters in millimeter-scale ducts. These nucleation rates play a significant role in most of the so-called convective …

Laser Ablation Of Aluminum, Erika Nosal, Zachary Rahe, Arthur Pamboukis

Williams Honors College, Honors Research Projects

The laser ablation of metal carries relevance in a variety of engineering industries. This includes, but is not limited to, processes such as micromachining, or implementation on aircraft weaponry. The latter application is the reasoning for why aluminum is the specific metal in consideration, as it is commonly used for the construction of aircraft components.

The scope of this project was to optimize the energy dispersed through laser ablation on aluminum by mathematical modeling. The transient conduction process in the aluminum was modeled using a 2-dimensional cylindrical coordinate system in both MATLAB and ANSYS/Fluent. These models were adopted to simulate …

Reduction Of Nox Emissions In A Single Cylinder Diesel Engine Using Sncr With In-Cylinder Injection Of Aqueous Urea, Anthony Timpanaro

UNF Graduate Theses and Dissertations

The subject of this study is the effect of in-cylinder selective non-catalytic reduction (SNCR) of NO_x emissions in diesel exhaust gas by means of direct injection of aqueous urea ((NH₂)₂CO) into the combustion chamber. A single cylinder diesel test engine was modified to accept an electronically controlled secondary common rail injection system to deliver the aqueous urea directly into the cylinder during engine operation.

Direct in-cylinder injection was chosen in order to ensure precise delivery of the reducing agent without the risk of any premature reactions taking place. Unlike direct in-cylinder injection of neat water, …

Transient Heat Storage Systems, Ian M. Sweeney, Brock M. Johnson, Todd K. Lundberg

Mechanical Engineering

Phase change materials (PCM) have many applications in transient cooling systems, including those with high transient heat loads and low duty cycles. These materials allow a system to remain within a narrow temperature range with a relatively low weight compared to conventional heat sinks or high-power cooling systems. This senior capstone project includes the design of a PCM based thermal energy storage system to integrate into an existing cooling loop, as well as a determination of viable PCM’s for the application. This report contains the necessary information to build the test apparatus.

Thermoelectric System Modeling And Design, Buddhima Pasindu Gamarachchi

Boise State University Theses and Dissertations

Thermoelectric generators (TEGs) convert heat to electricity by way of the Seebeck effect. TEGs have no moving parts and are environmentally friendly and can be implemented with systems to recover waste heat. This work examines complete thermoelectric systems, which include the (TEG) and heat exchangers or heat sinks attached to the hot and cold sides of the TEG to maintain the required temperature difference across the TEG. A 1-D steady state model is developed to predict the performance of a TEG given the required temperatures and device dimensions. The model is first validated using a 3-D model and then is …

The Impact Of Water Injection On Spark Ignition Engine Performance Under High Load Operation, Jeremy Worm

Dissertations, Master's Theses and Master's Reports

An experimental effort has been completed in which water injection was investigated as a means of enabling increases in engine output and high load efficiency. Water was injected into the intake port of a direct fuel injected, 4-cylinder, boosted engine with dual independent variable valve timing. The water was shown to increase volumetric efficiency and decrease the onset of knock which in turn enable more optimal combustion phasing. Both of these affects resulted increases in load of up to 5.5% at the same manifold pressure as the baseline case. The advancement of combustion phasing, combined with elimination of fuel enrichment …

The Emission And Particulate Matter Oxidation Performance Of A Scr Catalyst On A Diesel Particulate Filter With A Downstream Scr, Sagar Sharma

Dissertations, Master's Theses and Master's Reports

Selective catalytic reduction (SCR) systems along with a NH₃ slip control catalyst (ASC) offers NOₓ conversion efficiency >90 % with NH₃ slip < 20 ppm. However, future heavy duty diesel (HDD) engines are designed for higher engine-out NOₓ to improve fuel consumption. Consequently, there is a strong desire to further improve the NOₓ reduction performance of SCR systems, to meet the 2015 California Optional Low NOₓ Standard. SCR catalysts on a diesel particulate filter provide an effective solution to reduce NOₓ and PM using a single aftertreatment device. It also provides an opportunity to increase the SCR volume to achieve NOₓ conversion efficiency >95 %. A downstream SCR catalyst substrate can be used to get additional NO_x conversion by using the SCRF^® outlet NH₃ to increase the cumulative NOₓ conversion of the system.

In this study, NOₓ reduction, NH₃ slip and PM oxidation performance of a Cu-zeolite SCRF^® with a downstream Cu-zeolite SCR were investigated based on engine experimental data at steady state conditions. The experimental data were collected at varying SCRF^® inlet temperatures, space velocities, inlet …

Simulation Of Diesel Particulate Filter Regeneration Using Lattice Boltzmann Method, Kshitiz Kumar Jain

Dissertations, Master's Theses and Master's Reports

Lattice Boltzmann Method is a novel approach, which has shown promise in solving a wide variety of fluid flow problems including single and multi-phase flows in complex geometries. Volume elements of the fluid domain are considered to be composed of particles and these particles fall under a velocity distribution function at each grid point. Particles collide with each other under the influence of external forces and the rules of collision are defined so as to be compatible with the Navier-Stokes Equation. In the current work, LBM has been applied to Diesel Particulate filters which is a device used for reducing …

Photovoltaic Cooking In The Developing World, Tyler Watkins, Christopher O'Day, Omar Arriaga

Mechanical Engineering

The challenge of clean cooking is faced by hundreds of millions of people worldwide. We present a cooking technology consisting of a solar panel directly connected to an electric heater in a well-insulated chamber. Assuming continued decrease in solar panel prices, we anticipate that in a few decades Solar Electric Cooking technologies will be the most common cooking technology for the poor. Appropriate use of insulation reduces the power demand making low-power Insulated Solar Electric Cooking systems already cost competitive.

Fiber-Optic Imaging In An Internal Combustion Engine Test Rig, Conor Martin, Michael Smyser, Aswin Ramesh, Greg Shaver, Terrence Meyer

The Summer Undergraduate Research Fellowship (SURF) Symposium

The formation of particulate matter (PM/soot), nitrogen oxides (NOx), and other byproducts of the combustion process in diesel engines is controlled by spatiotemporally varying quantities within the engine cylinders which traditional sensors cannot resolve. This study explores the use of an advanced sensing technique using an optical probe which can be used to produce highly spatiotemporally resolved in cylinder images of the flame formation during the combustion stroke. Using a fiber optic cable and custom lensing system adapted to fit a pre-existing pressure transducer port, light from within the cylinder can be transmitted through the imaging probe to a high …

Micro Debris Generator, Gordan Bradaric, Ross Byers, Stephen Quanci

Mechanical Engineering

This senior project team at Cal Poly consisting of Stephen Quanci, Gordan Bradaric, and Ross Byers has been commissioned by Erik Brown of Lawrence Livermore National Labs to create a way to reliably and consistently entrain microscopic particles into the hot HTTU flow. These particles will be used to compare the loading rates of new HEPA filters by measuring the pressure drop across the filter. The generated particles would simulate typical conditions in which these HEPA filters are expected to operate, namely fine ash. The particles used for loading the filter are intended to simulate the particulate reaching the LLNL …

Efficiency Testing Of An Electronic Speed Controller, Grace Cowell, Matthew Hudson, Marcus Pereira

Mechanical Engineering

This project required the development of a rig that could experimentally determine the efficiency of an Electronic Speed Controller (ESC). The selected design focuses on measuring the losses due to heat from the device and comparing this to its input power. The selected design is a flow rig that utilizes the heat equation q=ṁcpΔT. The rig provides a steady state measurement of the ESC heat output by passing a known mass flow rate of air across the ESC and measuring the temperature difference. It uses a flowmeter to determine ṁ, thermocouples to determine ΔT, and a table lookup to determine …

A Study Of Constant Voltage Anemometry Frequency Response, Alex D. Powers

Master's Theses

The development of the constant voltage anemometer (CVA) for the boundary layer data system (BLDS) has been motivated by a need for the explicit autonomous measurement of velocity fluctuations in the boundary layer. The frequency response of a sensor operated by CVA has been studied analytically and experimentally. The thermal lag of the sensor is quantified by a time constant, M_CVA. When the time constant is decreased, the half-amplitude cut-off frequency, f_CVA, is increased, thereby decreasing the amount of attenuation during measurements. In this thesis, three main approaches have been outlined in theory and tested experimentally …

A Numerical Study Of Compressible Lid Driven Cavity Flow With A Moving Boundary, Amer Hussain

LSU New Orleans Theses and Dissertations

A two-dimensional (2-D), mathematical model is adopted to investigate the development of circulation patterns for compressible, laminar, and shear driven flow inside a rectangular cavity. The bottom of the cavity is free to move at a specified speed and the aspect ratio of the cavity is changed from 1.0 to 1.5. The vertical sides and the bottom of the cavity are assumed insulated. The cavity is filled with a compressible fluid with Prandtl number, Pr =1. The governing equations are solved numerically using the commercial Computational Fluid Dynamics (CFD) package ANSYS FLUENT 2015 and compared with the results for the …