Other Mechanical Engineering Commons^™

Jcati Carbon Fiber Recycling Shredder, Benjamin Cooley

All Undergraduate Projects

Once carbon fibers are cast into a resin and used in a composite material, retrieving those fibers can be a difficult task. However, it is beneficial to recycle and reuse the fibers from old unneeded components rather than pay the cost of acquiring new ones. The Joint Center for Aerospace Technology Innovation (JCATI) carbon fiber recycling device condenses the multistep process of extracting the fibers by integrating all steps into one automated device. In the previous version of the device, the cutting blades turned the long composite strips into thin fingers but did not sever them across the width.

The …

Design For Additive Manufacturing (3d Printing), Michael O'Donnell, Michael J. Levy

Williams Honors College, Honors Research Projects

The goal of this project is to study the performance of a 3D printed mechanical part subjected to topology optimization. A part that is somewhat complex in its load bearing and geometry will be selected. That part will then be designed, finite element analysis will be performed on it to optimize its topology, and then it will be 3D printed and tested. The goal of topology optimization is to either save material cost and/or part weight due to the ability of 3D printing to manufacture parts with complex and obscure geometry.

Chainless Bike Drive, Dominic Apisa, Bradley Powell, Garrett Colvin, John Monsour

Williams Honors College, Honors Research Projects

The focus of this project was to design a drive system that could replace the conventional chain drive system, improving on both the efficiency and reliability, in addition to being low cost and lightweight. This report will provide background into why this group chose this as the subject of their project, as well as challenges faced throughout the design process. The design developed was a drive shaft driven by a system of pinions and gears, with a freewheel mechanism that allowed the system to coast when not pedaling. Due to cost and time constraints, only a prototype was created, with …

Hydraulic Vehicle Challenge, Jacob Steiner, David Kotovets, Evan Blitz, Luke Fetherston, Alex Colucy

Williams Honors College, Honors Research Projects

The target goal of this project is for a team of students to design a vehicle which is based on human power as the primary mover of the system and achieves vehicle propulsion through the required use of hydraulics and pneumatics. In summary, the rider will power a pump that will generate pressure in order to move the fluid that drives the motor. This will result in the powered rotation of the wheels. As there are many possible designs, naturally, this means that the final design for the vehicle will have specific limitations such as weight and the required use …

Data Analysis To Evaluate The Performance Of Breathing Masks Used For Filtering Nano-Level Particles At Manufacturing Sites, Gracia M. Dardano

Honors College Theses

The work performed in this research aims to evaluate the performance of commercially available breathing masks in filtering airborne nanoparticles at manufacturing sites. Nanoparticles are found virtually anywhere, from dust in a worksite to a simple sneeze. Therefore, they pose a substantial threat to human health as their velocity and volatility are high. This research analyzes if current efforts of breathing masks to hinder nanoparticles are effective, especially at manufacturing sites. Data has been collected in order to analyze the behavior of nanoparticles and to measure nanoparticle levels at manufacturing sites and its working environment. Data is statistical in nature …

Homogenization Of Composite And Cellular Materials Incorporating Microstructure And Surface Energy Effects, Ahmad Gad

Mechanical Engineering Research Theses and Dissertations

In the last few decades, the popularity of composite and cellular materials has rapidly increased through their widespread applications in multiple engineering fields including aerospace, automotive, civil and biomedical. However, to a large extent, the success of their practical applications depends on our ability to predict their mechanical behavior by using high-fidelity mechanics models.

Micromechanical modeling of composite and cellular materials is a challenging task due to the heterogeneous nature of such materials and the interactions among various constituent phases at the microscopic level, which result in non-homogeneous deformation, strain and stress fields. Therefore, it is necessary to develop simple …

The Development Of All Solid-State Optical Cryo-Cooler, Junwei Meng

Optical Science and Engineering ETDs

This dissertation describes the development of an all solid-state optical cryo-cooler. Crystals of 10% wt. ytterbium-doped yttrium lithium fluoride (Yb³⁺:YLF) are used to cool an infrared HgCdTe sensor payload to an absolute temperature below 135 K, equivalent to delta T equal 138 K below ambient. This record level of cooling is accomplished with a single stage, in a completely vibration-free environment, with a corresponding cooling power of 190 mW. This milestone is made possible by the design and fabrication of an undoped YLF thermal link that efficiently shields the payload with a non-right angle kink from intense anti-Stokes …

Fluid Power Vehicle Challenge, Jacob Torrey, Kayla Londono, Bryson Chan, Aaron Trujillo

Mechanical Engineering

The FPVC combines mechanical engineering disciplines to design and manufacture a vehicle that utilizes hydraulic power. The FDR covers the final manufacturing process and verification processes developed during the front end of research and analysis built upon the Critical Design Review (CDR) and the PDR (Preliminary Design Review). This report showcases the design decisions and extensive research that supports the continuing efforts by the Team Pump My Ride, to build upon the accomplishments of Cal Poly’s previous team, The Incompressibles. The FDR presents how Team Pump My Ride produced the design changes from the CDR and PDR to achieve improvements …

Dual-Axis Solar Tracker, Bryan Kennedy

All Undergraduate Projects

Renewable energies, and fuels that are not fossil fuel-based, are one of the prolific topics of debate in modern society. With climate change now becoming a primary focus for scientists and innovators of today, one of the areas for the largest amount of potential and growth is that of the capturing and utilization of Solar Energy. This method involves using a mechanical system to track the progression of the sun as it traverses the sky throughout the day. A dual-axis solar tracker such as the one designed and built for this project, can follow the sun both azimuthally and in …

R/C Mini Baja Car: Drive Train And Steering, Carlton R. Mcdonald

All Undergraduate Projects

The purpose of the Baja R/C Car is to compete in the ASME eFX competition in a series of events to prove the functionality of the vehicle. This series of events includes the Slalom, Drag, and Baja race, The Slalom is a test in the steering capability of the vehicle, the Drag is a test in the acceleration of the vehicle in a straight line, and the Baja puts all factors together in a race to test every component of the vehicle. This project is about building an R/C car that not only functions, but also has maximum performance capabilities …

Automated Runout Measurement Tool, Ethan Tisch

Williams Honors College, Honors Research Projects

A new measurement process and tool is to be developed to improve the existing method for measuring runout on the commutators of brushed DC product.

After an armature is manufactured, the commutator is inspected by placing the completed rotor assembly in one of several non-standard measurement fixtures. An indicator is then positioned on the commutator. A trained operator proceeds to rotate the armature while taking runout and bar-to-bar measurement at various positions along the length of the commutator.

This existing process is slow, costly, and unreliable. For these reasons, there is substantial economic pressure to develop a superior method for …

Fluid Power Vehicle Challenge - The Incompressibles - Final Design Report, Nicholas Gholdoian, Russell Posin, David Vitt, Alex Knickerbocker, Kyle Franck, Julian Rodkiewicz

Mechanical Engineering

This report provides a comprehensive description of the research, analysis and design work that The Incompressibles have completed thus far in the senior project process. This document includes all the work that The Incompressibles have completed for the team’s Preliminary Design Review (PDR), Critical Design Review (CDR), the work leading up to the 2019 FPVC competiton and the competition results. This report includes the initial research that the team completed for the fluid power competition, first iterations of designs, final iterations of designs, manufacturing results and processes, and finally testing and results from competition. With a new design for the …

Nano Fab Lab 63, Brian K. Deemer, Josh Clemons, Nick Brodine, Delaney Fitzsimmons

Mechanical Engineering

Lawrence Livermore National Laboratories (LLNL) has several steps in the production process for ceramic nanofiber tubes that they would like to improve - electrospinning, cutting, rolling, sealing and heat treating. We undertook the challenge to deliver LLNL with a semi-automated process that efficiently integrates the steps of cutting, rolling, and sealing to save time and improve control over end dimensions. In this document, we discuss the technical background of the manufacturing steps currently followed to create nanofiber tubes, identify which steps are incorporated in our prototype and explain how they will interface with one another, define the design requirements, present …

Investigation Of Design, Manufacture, Analysis, And Test Of A Composite Connecting Rod Under Compression, Thomas Juhl Rohrbach

Master's Theses

Composite materials hold great potential for the replacement of traditional materials in machines utilized on a daily basis. One such example is within an engine block assembly where massive components inherently reduce the efficiency of the system they constitute. By replacing metal elements such as connecting rods, cylinder caps, or a crank shaft with composite alternatives, a significant increase in performance may be achieved with respect to mechanical strength, thermal stability, and durability, while also reducing mass. Exploration of this technology applied to a connecting rod geometry was investigated through a combination of process development, manufacturing, numerical analysis and testing. …

Stair Climbing Hand Truck, James Mcpherson

All Undergraduate Projects

Abstract

Getting a heavy object up a flight of stairs usually requires a team of two or more people. Even with a team of people, the task is often still difficult, dangerous, and possibly insurmountable by one person. This problem is especially prevalent in for those who are moving into apartment complexes. Most apartment complexes have many buildings with two or more floors of living quarters, and elevators are often missing. This project sought to offer a solution to this problem. The solution in question; a motorized hand-truck with 2, trigonal planar pinwheels in place of the stock wheels. The …

Autojack - Hydraulic Powertrain System, Tyce Vu

All Undergraduate Projects

A primary problem for mechanics and automotive enthusiasts is the risk associated with lifting and securing a vehicle with conventional jack stands. Often times, improper jack-stand installation results in the vehicle collapsing unexpectedly, causing injury and/or death. This problem can be minimized through the application of a newly re-designed vehicle lifting system. The conventional method for lifting cars is time consuming and can be unsafe in many circumstances. A better, safer, and more efficient lift design was needed; the AutoJack. The approach of the AutoJack design was entirely focused on the safety of lifting a vehicle. Safety was improved by …

Ares Cleaning System, Andy Sagers, John Cunningham, Peter Greig, Jack Glynn

Mechanical Engineering

In this Final Design Review, the team outlines the general scope of the ARES Cleaning System project and the final design direction chosen and built. This team consists of a group of four mechanical engineering students who have been tasked with designing and manufacturing an autonomous ARES cleaning system to help their sponsor, Fracsun, better track soiling losses measured at large solar arrays. They designed, conceptualized, manufactured, and tested throughout the project as they looked to create a final, functioning product. In creating this Final Design Review, they have identified how the product will perform the desired functions and what …

Recumbent Bicycle Balancing Aid, James Hager

Williams Honors College, Honors Research Projects

For our senior design project, our team will be consulting to create a balancing aid system intended for the recumbent bicycle shown below in Figure 1. The owner of the bicycle is Robert Henderson, a former United States Navy sailor from Northeast Ohio who picked up biking and skiing while he was stationed in Maine in the late 80’s. While there, he took to the mountains on the rugged terrain and brought this passion of biking back home to share with his wife, Johanna once he completed his service to his country. Biking became an integral part of the …

Reinventing The Wheel, Esther K. Unti, Ahmed Z. Shorab, Patrick B. Kragen, Adam M. Menashe

Mechanical Engineering

Reinventing the Wheel selected tires and designed wheels for the 2018 Cal Poly, San Luis Obispo Formula SAE combustion vehicle. Available tire options were evaluated for steady-state and transient performance as well as vehicle integration. A single-piece composite wheel with hollow spokes was designed to meet stiffness, strength, and tolerance requirements. A detailed study of wheel loading and geometric structural efficiency was performed. Finite element analysis was used to iterate the geometry and laminate. A two-piece male mold was designed and machined to manufacture the wheel. Removable silicone inserts were used to create the hollow spokes.

All-Terrain Storage Surfboard Carts, Ben M. Kennedy, Danny Riedeman, Roberto Gonzalez

Mechanical Engineering

All Terrain Storage consists of three mechanical engineering students: Roberto Gonzalez, Ben Kennedy, and Danny Riedeman. The goal of All Terrain Storage is to design and create two portable storage devices for the non-profit organization AmpSurf. AmpSurf helps veterans, people with disabilities, and anyone else who could be helped through adaptive surfing and other outdoor activities. Their current method of storing and transporting equipment for events is carrying it from the trailer in the parking lot through the sand onto the beach. This document will provide: a more thorough introduction to AmpSurf and the project, the objectives, background information, the …

Daimscale — 1:14th Tractor-Trailer For Testing Driver Assistance Technology, Christopher Marrale, Jase Sasaki, Devin Bodmer

Mechanical Engineering

Active driver assistance systems are becoming increasingly wide-spread throughout the automotive industry due to their potential for safer roads and decreased costs of transportation, but testing these systems on real trucks can be time consuming, dangerous, and costly. Testing these systems on a small-scale tractor-trailer combination will lead to faster and more efficient development of driver assistance systems and can be used by both engineers and students, leading to a larger field of experienced developers to improve these systems.

Our goal will be to design, manufacture, and build a scale 6x2 model of the tractor portion of a Daimler semi-truck …

Design For Maintainability In Developing Communities—A Case Study On The Uros Islands, Thomas Barlow

Undergraduate Honors Theses

Designing products for developing communities has exposed many of the underlying assumptions that engineers from developed nations have during the design process. There has been much written about these underlying assumptions in order to create a better framework for designing for developing communities. One unexplored, yet important area is the universality of common maintainability principles used in developed countries when designing products used in developing communities. Such principles include: simplicity, diagnosability, standardization of parts, modular subassemblies, minimizing assembly and disassembly parts, labeling components, increased life of moving parts, manuals, and simplifying tools needed for repairs [1]–[3]. The purpose of this …

Prove Endurance Car Front Suspension, Lauren A. Williams, Logan Simon, Justine G. Kwan

Mechanical Engineering

This document details the collaborative Mechanical Engineering Senior Project with Cal Poly PROVE Lab on PROVE Lab’s Project 2; an electric vehicle designed to travel 1000 miles on a single charge. Logan Simon, Justine Kwan, and Lauren Williams are given the challenge of designing an innovative proof of concept front suspension suspension for this vehicle.

After detailed research of new suspension systems, it was determined that the innovative nature could be in the form of unique manufacturing methods, materials use, or mechanical design. At this point in time, this vehicle is a purely conceptual design with no concrete requirements. Therefore …

Universal Studios Hollywood Vip Trolley - Roller Frame, Jeffrey Ploss, Chase Montague, Lincoln Treanor

Mechanical Engineering

Statement of Confidentiality: The complete senior project report was submitted to the project advisor and sponsor. The results of this project are of a confidential nature and will not be published at this time.

H.F. Hauff Electric Pruner Drive Train, Grady Graff

All Undergraduate Projects

The H.F. Hauff Company invests a large amount of money in developing a quality pruner used in everyday agriculture. Modern electric pruners tend to be expensive while manual tree pruning is very physically demanding. A battery assisted pruner that is light-weight, ergonomic, inexpensive to build and powerful enough to cut branches that a nominal apple tree would possess is the direct affiliation that H.F. Hauff devotes its funding too. A team of engineering students from Central Washington University developed a product with consideration to each of these circumstances. Since hand drills have proven to be user friendly and of abundance …

Human Powered Vehicle Design Team: Speed Variable Steering Stabilizer, Eric Miller, Matt Kraml

Williams Honors College, Honors Research Projects

The Human Powered Vehicle Competition (HPVC) is held annually by ASME at a few locations. The University of Akron has competed in the ASME-East and ASME-West competitions over the past handful of years against universities from all over the world. Objectives of each team for the competition are three-fold: vehicle design, racing performance, and innovation. Our senior design project involved working on the innovation concept for ASME-East 2018 held at Penn State University during the weekend of 4/13. Speed variable steering was decided upon by the entire HPVC team early in the design process as the innovation choice for this …

Boat-Lift Design And Analysis, Nathan Schick

Honors Theses

A current in production 6000 lb. rated boat-lift is being sold at “Great Lake Lifts”. The lift was tested experimentally and proved to hold at least 8000 lb. The design team successfully modeled the current lift on Ansys to help the customer understand where the weakest points in the design were. Following the creation of the initial lift design, the design team proposed and tested modifications that could be made in order to make the lift more structurally sound. The initial lift had a maximum deflection of 0.43846 inches, a maximum stress of 15880 psi, and a safety factor of …

Dyno-Mite Redesign, Brandon Joseph Miller, Daniel Robert Hoffman, Richard Demedici Young

Mechanical Engineering

The Cal Poly Mechanical Control Systems Laboratory currently employs an outdated device, known as the Motomatic, to teach students about various motor characteristics and control methods. These include open-loop vs. closed-loop control, speed vs. position control, and DC motor response curves. The current device does not function properly and produces unreliable data due to overwhelming non-linear effects such as stiction and shaft misalignment. Our team was tasked with designing a replacement device that retains many of the same educational goals as the original lab procedure, while also adding new educational goals pertaining to the device system dynamics. The new apparatus, …

Medium Duty Gas-Turbine Engine Blade Removal Tool, Elliott James Greb, Jacob Thomas Syage, Kellen Thomas Field

Mechanical Engineering

Solar Turbines Incorporated sponsored a team of three Cal Poly Undergraduate Mechanical Engineering students to design, manufacture, prototype, and test a tool for the removal of turbine blades from their respective disk assembly without damaging the disk itself. The tool was developed for Solar’s industrial gas turbine engines. The tool complies with all OSHA and Solar Turbines safety and engineering constraints, and was designed for use in a shop facility. The tool was made adaptable for geometric variances in multiple turbine rotor disk stages, and requires no more than one technician to operate using a maximum of two shop resources. …

Anchoring And Stiffening Techniques For Portable Concrete Barriers, Surajkumar Bhakta

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Portable concrete barrier (PCB) systems are utilized on federal and state highways in circumstances such as placing adjacent to vertical drop-offs and in construction zones. PCB systems are most commonly used in a free-standing configuration, which are known to have relatively large deflections when impacted. Large deflections are undesirable when dealing with limited space. In order to allow PCBs to be used in space restricted locations, seven PCB anchoring and stiffening techniques were tested and evaluated as per Manual for Assessing Safety Hardware (MASH) testing standards. Results will allow the New Jersey Department of Transportation to update guidance for their …