Manufacturing Commons^™

Exploring Methods For Recycling Filament Waste In 3d Printing, Max Rios Carballo

Publications and Research

The goal of the current study is to investigate cutting-edge techniques for recycling filament waste from 3D printing procedures. Appropriate waste management techniques are required to reduce this trash's harmful environmental consequences. The goal of the project is to look at new methods for recycling filament waste in order to minimize disposal and encourage reuse. To acquire data from pertinent papers and research, a thorough literature review methodology was used. The findings show that this issue may be resolved utilizing a variety of recycling techniques, including shredding, melting, and re-extrusion. The type of filament waste and the intended goal will …

Mechanical Characterization Of Additively Manufactured Alloys Compared To Their Wrought Counterparts, Laith A. Alqawasmi

Mechanical Engineering ETDs

Additive manufacturing is a method of manufacturing based on building parts layer by layer, allowing for more control over shape of the product, therefore reducing machining costs, reducing material waste, faster production times and the ability to build complex engineering design that other manufacturing technologies won’t be able to produce. This research is on the tensile and indentation testing (following ASME standards) of 3D printed Ti-6Al-4V and Inconel 718 built by powder-based direct energy deposition technology. Ti-6Al-4V is an attractive material for the aerospace and aviation industry, and Inconel 718, a nickel-chromium based superalloy, is an attractive material for usage …

Fast-, Light-Cured Scintillating Plastic For 3d-Printing Applications, Brian G. Frandsen, Michael Febbraro, Thomas Ruland, Theodore W. Stephens, Paul A. Hausladen, Juan J. Manfredi, James E. Bevins

Faculty Publications

Additive manufacturing techniques enable a wide range of possibilities for novel radiation detectors spanning simple to highly complex geometries, multi-material composites, and metamaterials that are either impossible or cost prohibitive to produce using conventional methods. The present work identifies a set of promising formulations of photocurable scintillator resins capable of neutron-gamma pulse shape discrimination (PSD) to support the additive manufacturing of fast neutron detectors. The development of these resins utilizes a step-by-step, trial-and-error approach to identify different monomer and cross-linker combinations that meet the requirements for 3D printing followed by a 2-level factorial parameter study to optimize the radiation detection …

Launching A 3d Printing Program For Students: Recommendations And Best Practices For Libraries, Wilhelmina Randtke, Lee Bareford

Georgia Library Quarterly

The Georgia Southern University Libraries launched a 3D printing program for students in July 2022. Prior to launch, library employees at two of Georgia Southern University’s campuses investigated options for implementing safe, affordable, and sustainable 3D printing in existing academic libraries without retrofitting costly ventilation systems into existing facilities. This article describes the reasons why the Georgia Southern University Libraries thought that a 3D printing program could fulfill a service need for students across university colleges and departments and outlines some of the challenges, best practices, and unique innovations that the library’s employees experienced throughout the program launch process. The …

Recycling Metal Chips Into Usable Materials, Alex Mortensen, Ben Mortensen

Williams Honors College, Honors Research Projects

This report entails the scope, design considerations, and plans for creating a metal chip converter into metal briquettes. The construction is a set of machines with multiple processes to make the conversion happen. The process includes washing fine metal chips, drying them off, compressing them, and melting them down into usable briquettes. This project is intended to make a simple process to recycle metal chips into usable material for reuse. The project's objective is to reduce the costs of storage and recycling waste by offering a solution to recycle it into materials the shop can reuse.

Dome Tester, Clark Bates, Nikolas M. Kulin

Williams Honors College, Honors Research Projects

We are reconfiguring and modifying the previously built dome tester to be more user friendly and mechanically applicable. This has a long-term goal of being a usable teaching tool for manufacturing education within the college of engineering and polymer sciences. The dome tester pushes a metal dome into a clamped sheet of metal to test its forming limits and where necking occurs. We have implemented a better method of viewing the sheet sample as it is being deformed, and improved measuring methods for the distance a sample is deformed. By introducing these changes in conjunction with improved documentation of the …

Investigation Of Microstructurally Dependent Mechanical Properties Of Cold Sprayed Copper Using Correlative Microscopy, Quintin Otto

UNF Graduate Theses and Dissertations

This project employs multi-instrument materials characterization to analyze material made with the “Cold Spray” additive manufacturing process. Cold spray is an emerging additive manufacturing technique with unique benefits resulting from its low temperature adhesion process induced by plastic deformation. Metallic powder collides at high speeds creating three dimensional materials and coatings without the need for melting. Copper cold sprayed specimens were analyzed using a series of imaging techniques to characterize the microstructure at varying levels of detail and magnification. Scanning electron microscopy and electron back scattered diffraction were paired with microhardness testing to generate a correlative comparison between microstructure and …

Modified Reactive Sputter Deposition Of Titanium Nitride Thin Films Via Hipims With Kick-Pulse And Improvement Of The Structure-Zone Model, Andrew Miceli

UNF Graduate Theses and Dissertations

Direct current (DC) and radio frequency (RF) sputtering methods have been commonplace in industry for several decades and widely studied in literature. Hard films of nitrides, such as titanium nitride (TiN), have been deposited using reactive DC sputtering onto cutting tools and medical devices extensively as well. For these applications, the films require excellent adhesion, high density, and high hardness. High-Power Impulse Magnetron Sputtering (HIPIMS) has emerged over the last several years as a method to produce films with increased density and mechanical properties. Process-structure-property relationships for reactive HIPIMS are not yet well developed. Additionally, conventional HIPIMS suffers from relatively …

Investigation Of Manufacturing Techniques For Magnetorheological Elastomers To Expand Feasibility In A Diverse Array Of Applications, Austin S. Robbins

College of Graduate Studies: Theses & Dissertations

Magnetorheological elastomers, or MREs, are smart composite materials with controllable physical and mechanical properties when introduced to an external stimulus of a magnetic field. The controllability of these properties is highly tunable by the selection of the elastomeric matrix, concentration of magnetically permeable particles, introduction of additives, and the alignment of the constituents during the curing process. The fabrication of MREs typically calls for a mold that is filled with an MRE mixture to create the final desired geometry after curing. These molds are frequently placed under a magnetic field which orients the micron sized magnetic particles along the magnetic …

Development Of Inconel 718f And Inconel 718e Powders For Parts Manufacturing Utilizing Binder Jet Three-Dimensional Printing And Compressed Pellet Methods, Duncan Eric Manor Ii

Graduate Theses, Dissertations, and Problem Reports (ETD)

Alloy Inconel 718 is a Ni based superalloy used for high temperature applications including turbine blades, turbocharger rotors and nuclear reactors. Inconel 718 is a popular commercial atomized powder that has limitations in performance for use in additive manufacturing applications due to poor part quality and efficiency of current fabrication methods. Developing new compositions and additive manufacturing (AM) methodologies of IN718 is critical to improve the quality and the efficiency of IN718 parts manufacturing. Developing new additive manufacturing methodology that produces higher quality parts made of IN718 as compared to current methods has the potential to greatly impact industry, academia, …

Additive Manufacturing Of Variable Contrast Computed Tomography Anatomical Phantoms Using A Single Feedstock In Fused Filament Fabrication, Cory J. Darling

LSU New Orleans Theses and Dissertations

Anatomical phantoms used in biomedical education and training benefit greatly from Fused filament fabrication’s (FFF) ability to rapidly produce complex and unique models. Current materials and methods used in FFF have limited ability to accurately produce phantoms that can mimic the radiological properties of multiple biological tissues. This research demonstrates that the CT contrast of FFF produced models can be modified by varying the concentration of bismuth oxide in acrylonitrile butadiene styrene (ABS) filaments and a tunable CT contrast that mimics the CT contrast ranging from fatty tissue to cortical bone using a single composite filament without introducing artificial image …

Effects Of Additive Manufacturing Techniques On The Magnetocaloric Properties And Chemical Stability Of Lafexcoysi13-X-Y Alloys, Binyam Wodajo

Theses and Dissertations

Additive manufacturing (AM) is an emerging process to fabricate net shape, intricate, engineering components with minimal material waste; however, traditionally it has been largely applied to structural materials. AM of functional materials, such as magnetic materials, has received much less attention and the field is still in its infancy. To date, AM of magnetocaloric regenerators for magnetic refrigeration (an energy-efficient alternative to the conventional vapor-compression cooling technology), remains a challenge. There are several magnetic refrigerator device designs in existence today that are predicted to be highly energy-efficient, on condition that suitable working materials can be developed. This challenge in manufacturing …

Sound, Material And Strength Correlation, Ryan Mcbride

Symposium of Student Scholars

With a growing amount of manufacturing utilizing 3D printing, there is a correlation between strength and material which can affect sound produced by sirens. An air raid siren that has been downloaded from Thingiverse.com spins with a 49:1 gear ratio to produce 2 tone sounds and with that large number of revolutions comes friction, and in order to create a 3D printed air raid siren, the siren must be made out of a material that can withstand high temperatures without melting and quick rotations without delaminating. There are many materials that can be printed to withstand those forces, but it …

Hydraulic Balsa Wood Rising Bridge, Kaitlyn Greenfield

All Undergraduate Projects

What is the solution to allowing tall vessels to navigate past a vehicle bridge that is less than 10 [ft] above the water? To answer this question, a balsa wood bridge was designed, constructed, and tested. The bridge needed to articulate by mechanical means, allow for travel through the bridge, and be able to withstand ample force while the main structure only being constructed of balsa wood and glue. The project was analyzed in sections. These sections include: the bridge structure and its members, the hydraulic lift, and the pins needed for the bridge and hydraulic lift to operate. The …

Advance Metallic Reinforcement Of Vat Photo Polymerized Parts, Scott Zinn

UNF Graduate Theses and Dissertations

The metallization or metallic reinforcement of polymer parts has been widely used in industry for several decades. Polymer parts are classically metalized for aesthetics, chemical and thermal resistance, electrical conductivity, and mechanical strength. Metallization has been shown to increase strength of polymer parts when compared to the strength of the bulk material without metallization. Additive manufacturing (AM) techniques that have emerged in the last few decades produce parts with different surface features and chemistry than the typical polymer part produced through injection molding. AM parts are typically weaker than traditionally manufactured parts from the same material due to intrinsic details …

The Development Of A Holistic Quality Score Using In-Situ Monitoring Of Laser Powder Bed Fusion, Ryan Daigneault

College of Graduate Studies: Theses & Dissertations

Additive manufacturing processes allow for a great degree of flexibility in terms of part production. The process is autonomous once the part has started printing in that the operator generally does not need to intervene until the part is finished. One issue that this introduces, however, is an inability to determine part quality during the printing process. Once a part has started printing, the operator must either wait until the part is finished or regularly check on the part during the print to determine the part quality. Using data gathered from multiple sensors, a quality score can be used to …

Miniaturized Ultraviolet Imager Phase Iii, Bradley D. Albright, Nicolas A. Armenta, Colin W. Harrop

Mechanical Engineering

This document details the work to date, June 9, 2020, done by the Cal Poly Mechanical Engineering senior project team, Miniaturized Ultraviolet Imager: Phase III (MUVI III), sponsored by the University of California, Berkeley – Space Sciences Laboratory (UCB SSL). MUVI III is the third senior project team of an ongoing design, MUVI: the prototype of a 2U sized CubeSat intended to capture aurora images in the ionosphere. The first team, MUVI I, finished development of the UV imager. The second team, MUVI II, designed the mirror mounting and deployable door mechanisms. The goal of MUVI phase III is to …

Comparative Analysis And Dynamic Response Of Garolites Under Temperature Spectrum Using Low Velocity Impact Test, Birendra Chaudhary

Honors Theses

The purpose of this study was to examine the dynamic response of three different grades of garolites under the temperature spectrum. High-Temperature G-11 Sheet (HTG), Impact Resistance Garolite E-glass (HIG), and Economical Garolite (EG) were tested using an Instron Dynatup 8250 impact tester. Three specimens were used for all three composites and were tested at 6 different temperatures, -10^oC, 25^oC, 50^oC, 100^oC, 150^oC and 200^oC using the Low-Velocity Impact Machine with 20 Kip punch shear load cell. The results showed that HIG had the highest resistance to punch …

Jominy Hardenability Tester With In-Situ Heating, Luke Allen

Williams Honors College, Honors Research Projects

This project centers on building a Jominy Hardenability tester with In-Situ heating for the manufacturing lab at the University of Akron. A new process and setup will be designed using engineering concepts in order to make the testing more efficient and safer for the teaching and testing of metal hardness. The current Jominy testing setup has efficiency issues within the transfer of specimen from induction heater to testing rig. Our design will simplify the design by creating a test rig that removes the traveling aspect of the specimen which will limit the amount of premature cooling done and will be …

Table Top Dome Tester, Travis Bernard, Sarah Kassinger, Amanda O'Reilly, Scott Salerno

Williams Honors College, Honors Research Projects

The Erichsen Cupping Test was used as a basis to design a dome tester. The intention of a dome tester is to test sheet metal material properties in all directions. This was done by clamping a piece of sheet metal and using a piston and hydraulic press to punch through the material. The force used to punch the material and the height of the deforming material can be gathered and the sheet metal properties can then be calculated. At the end of the project the team was able to successfully design and manufacture a hydraulic dome tester. However, due to …

Tabletop Mechanical Tester, Jamie Dombroski, Brian English, Richard Leffler, Andrew Shirk

Williams Honors College, Honors Research Projects

The need for hands-on and face-to-face experiences in the engineering classroom is very great. The equations, principles, and concepts can all be learned, but without the visual and tactile application, these don’t always sink in or become concrete. A small-scale tensile test machine was designed, sourced, manufactured, and tested for the purpose of being applied in classroom settings to provide this experience to engineering students. Extensive research was performed concerning tensile machines on the market, the essential elements of which are the load cell, grips, crosshead, extensometer, motor, and frame. The raw materials for the frame were purchased and drawings …

An Investigation Of High-Speed Consolidation And Repair Of Carbon Fiber - Epoxy Composites Through Ultrasonic Welding, David A. Hoskins

LSU Master's Theses

Adhesive repair of carbon fiber composite structures is commonly done on damaged structures to extend the service life. This method requires careful preparation of the damaged surface with intricate steps to ensure good bonding between the repair patch and the parent structure by means of an adhesive film. As with many forms of composite manufacturing, it is required to perform vacuum bagging, debulking, and a heated cure depending on the resin. All these steps make the repair process costly and time consuming.

In this present work, an alternative method of repair is investigated which explores the experimental feasibility of using …

Development Of Experimental And Finite Element Models To Show Size Effects In The Forming Of Thin Sheet Metals, Jeffrey D. Morris

LSU New Orleans Theses and Dissertations

Abstract

An experimental method was developed that demonstrated the size effects in forming thin sheet metals, and a finite element model was developed to predict the effects demonstrated by the experiment. A universal testing machine (UTM) was used to form aluminum and copper of varying thicknesses (less than 1mm) into a hemispherical dome. A stereolithography additive manufacturing technology was used to fabricate the punch and die from a UV curing resin. There was agreement between the experimental and numerical models. The results showed that geometric size effects were significant for both materials, and these effects increased as the thickness of …

Nano Fab Lab 63, Brian K. Deemer, Josh Clemons, Nick Brodine, Delaney Fitzsimmons

Mechanical Engineering

Lawrence Livermore National Laboratories (LLNL) has several steps in the production process for ceramic nanofiber tubes that they would like to improve - electrospinning, cutting, rolling, sealing and heat treating. We undertook the challenge to deliver LLNL with a semi-automated process that efficiently integrates the steps of cutting, rolling, and sealing to save time and improve control over end dimensions. In this document, we discuss the technical background of the manufacturing steps currently followed to create nanofiber tubes, identify which steps are incorporated in our prototype and explain how they will interface with one another, define the design requirements, present …

A Study On Ultrasonic Energy Assisted Metal Processing : Its Correeltion With Microstructure And Properties, And Its Application To Additive Manufacturing., Anagh Deshpande

Electronic Theses and Dissertations

Additive manufacturing or 3d printing is the process of constructing a 3-dimensional object layer-by-layer. This additive approach to manufacturing has enabled fabrication of complex components directly from a computer model (or a CAD model). The process has now matured from its earlier version of being a rapid prototyping tool to a technology that can fabricate service-ready components. Development of low-cost polymer additive manufacturing printers enabled by open source Fused Deposition Modeling (FDM) printers and printers of other technologies like SLA and binder jetting has made polymer additive manufacturing accessible and affordable. But the metal additive manufacturing technologies are still expensive …

Additive Manufacturing Of High Performance Flexible Thermoelectric Generators Using Nanoparticle Inks, Tony Valayil Varghese

Boise State University Theses and Dissertations

Flexible thermoelectric devices are attractive power sources for the growing demand of flexible electronics and sensors. Thermoelectric generators have an advantage due to no moving parts, silent operation and constant power production with a thermal gradient.

Conventional thermoelectric devices are rigid and fabricated using complex and relatively costly manufacturing processes, presenting a barrier to increase the market share of this technology. To overcome such barriers, this work focuses on developing near ambient-temperature flexible thermoelectric generators using relatively low-cost additive manufacturing processes. A screen printable ink was developed for transforming nanoparticle ink into high-performance flexible thermoelectric generators with a peak thermoelectric …

Autojack - Hydraulic Powertrain System, Tyce Vu

All Undergraduate Projects

A primary problem for mechanics and automotive enthusiasts is the risk associated with lifting and securing a vehicle with conventional jack stands. Often times, improper jack-stand installation results in the vehicle collapsing unexpectedly, causing injury and/or death. This problem can be minimized through the application of a newly re-designed vehicle lifting system. The conventional method for lifting cars is time consuming and can be unsafe in many circumstances. A better, safer, and more efficient lift design was needed; the AutoJack. The approach of the AutoJack design was entirely focused on the safety of lifting a vehicle. Safety was improved by …

Carbon Fiber Monocoque, Dan Brown, Leland Hoffman

Williams Honors College, Honors Research Projects

The University of Akron’s Human Powered Vehicle Team designed a high performing, fully functioning vehicle that is safe, efficient, and practical for the 2018-2019 season. These objectives were the main priorities when it came to the initial stages of designing the vehicle. In addition, the vehicle was designed in accordance with the ASME 2019 Human Powered Vehicle Challenge guidelines to satisfy all the rules and requirements. Additional priorities have been created to teach practical engineering skills and techniques to the students participating in the project through different points in the production process including research, vehicle design, construction, and testing.

The …

Optimization Of The Practice Of Slow Cooling Steel Bars: A Redesign And Modernization Of Materials, Eryn Johnston

Mechanical Engineering Undergraduate Honors Theses

Throughout the process of steel making, certain grades of steel are a higher risk for defects caused by the inability to quickly diffuse hydrogen through the steel when cooled to room temperature at a normal rate based on the ambient air temperature. To reduce the hydrogen flaking defects that are caused due to hydrogen entrapment in the steel, the process of slow cooling is utilized. This process reduces the cooling rate of steel bars by keeping them at a higher temperature for extended periods and in turn gives the hydrogen a chance to fully dissipate from the steel. In many …

Reinventing The Wheel, Esther K. Unti, Ahmed Z. Shorab, Patrick B. Kragen, Adam M. Menashe

Mechanical Engineering

Reinventing the Wheel selected tires and designed wheels for the 2018 Cal Poly, San Luis Obispo Formula SAE combustion vehicle. Available tire options were evaluated for steady-state and transient performance as well as vehicle integration. A single-piece composite wheel with hollow spokes was designed to meet stiffness, strength, and tolerance requirements. A detailed study of wheel loading and geometric structural efficiency was performed. Finite element analysis was used to iterate the geometry and laminate. A two-piece male mold was designed and machined to manufacture the wheel. Removable silicone inserts were used to create the hollow spokes.