Manufacturing Commons^™

Optimization Of Aluminum Coating Deposition Parameters To Enhance The Performance Of Automotive Headlamps, Gulirano Saidakhmedova, Giovanni Maizza

Technical science and innovation

The paper investigates the influence of the optical characteristics of functional coatings applied to automotive reflectors on vehicle active safety parameters, with a focus on the range and intensity of road illumination. The study examines the mathematical relationship between the maximum luminous intensity of a headlamp, the object detection distance, and the reflection coefficient  of an aluminium layer deposited via vacuum thermal evaporation. The main factors driving the degradation of surface reflectivity (including oxidation, thermal degradation of the base coat, and surface roughness) are analysed. It is demonstrated that a decrease in the reflection coefficient during operation directly impairs the …

Direct Ink Writing Of Functional Fiber/Granular Composites, Zhuoyuan Yang

Doctoral Dissertations and Master's Theses

Direct ink writing provides a versatile manufacturing route for fabricating functional fiber and granular composites with controlled architecture, tunable interfaces, and customized material distributions. Fiber reinforced composites offer high stiffness, strength, fatigue resistance, and functional anisotropy, while granular composites provide scalable access to particle based structures with high material efficiency and broad resource compatibility. However, the additive manufacturing of these composite systems remains challenging. For fiber based composites, precise control of fiber placement, matrix impregnation, interfacial bonding, and freestanding deposition is difficult to achieve during printing. For granular composites, stable particle flow, controllable packing, binder infiltration, and shape retention are …

Mechanical Behavior Of Additively Manufactured Ti-6al-4v Eli Parts: Effects Of Laser Parameter Selection, Samuel Lopez

UNF Graduate Theses and Dissertations

Additive manufacturing (AM) of TI-6AL‑4V Extra‑Low Interstitial (ELI) enables complex geometries for fatigue‑critical medical device applications, yet fatigue performance remains sensitive to process‑induced defects. This work investigates the effect of laser process parameter selection on the microstructure, mechanical properties, and fatigue behavior of TI- 6AL‑4V ELI fabricated via laser powder bed fusion (L‑PBF) using a Renishaw RenAM system. The influence of laser parameters was isolated by holding powder chemistry, build orientation, scan strategy, sub‑transus annealing, and post‑processing constant between a non‑optimized baseline and an optimized parameter set selected based on tensile performance.

Optical microscopy showed the optimized condition exhibited improved …

Field-Assisted Post-Processing Of Cold-Sprayed Pure Copper, Alan Hensley

Theses and Dissertations--Mechanical and Aerospace Engineering

The properties of materials processed through cold spray, and many other AM processes, are non-uniform and unpredictable. In most cases, post-processing is required to achieve desired properties and better uniformity. In cold spray, the typical method is an annealing heat treatment (AHT), which can improve bond strength, reduce porosity, and restore ductility, among other effects. AHT alone, however, is unable to completely remedy any of the unfavorable properties. In addition, long treatments at high temperatures are often needed for satisfactory results. This increases energy consumption and extends production times for products made by the process. For these reasons, numerous investigations …

Hydrogen Embrittlement In Shot-Peened Steel, Jia-Huei Tien, David R. Johnson, David Bahr

15th International Conference on Shot Peening

This work investigates the role of shot peening on hydrogen embrittlement resistance in quenched and tempered 1070 steel. Thermal desorption spectroscopy results revealed that shot-peened specimens contained nearly twice the hydrogen (H) content of unpeened samples when charged under the same electrochemical conditions, suggesting the introduction of additional trapping sites occur during peening. The mechanism underlying this behavior can be associated with increased dislocation density and is more consistent with the HELP mechanism. Residual stress measurements show a significant relaxation of compressive stresses in shot-peened specimen after H charging, indicating H enhanced dislocation rearrangement. Both unpeened and peened specimens exhibited …

Comparison Of Peening Effect Between Additive Manufacutred And Drawing Titanium Alloy, Hitoshi Soyama

15th International Conference on Shot Peening

Although additively manufactured (AM) metals are attractive materials, their remarkable weak fatigue properties are an obstacle to their practical application. Thus, post-processing to improve their fatigue properties is required. In the present study, powder bed fusion using laser sintering titanium alloy, i.e., PBF-LS/Ti6Al4V was treated by shot peening (SP), submerged laser peening (SLP), cavitation peening (CP), and fine particle bombarding (FPB), then the fatigue properties were investigated by a torsional fatigue test, comparing with drawing Ti6Al4V. It was revealed that the fatigue strength at 10⁷ was 446 ± 5 MPa for PBF-LS/Ti6Al4V treated by FPB+CP, 359 ± 9 MPa …

In-Situ Defect Detection In Selective Laser Melting Using Convolutional Neural Networks, Ethan Gaigalas

Master's Theses

This thesis develops and trains a convolutional neural network (CNN) to classify defects in metal parts produced by selective laser melting (SLM) using acoustic emission (AE) data. The model successfully identified porosity and standard build layers with high accuracy but consistently struggled to classify lack of fusion (LOF) defects, regardless of input type, normalization, or class count. These results suggest that while AE signals contain distinguishable features for certain defect types, LOF signals may be too subtle or inconsistent for reliable detection. The study addresses the ongoing challenge of in-situ quality monitoring in metal additive manufacturing, where defects like cracks, …

3d Printed Fixed Wing Aircraft Competition, Sidney E. Long, Mitchell Heise, Jack Bride, Daniel Salinas

Mechanical Engineering

Cal State LA and Arlington University, Texas are hosting the same 3D printed, fixed wing aircraft competition for 2025. Cal Poly requires a competitive plane that can adhere to each rule and be piloted remotely to achieve the longest time in the air. The plane must utilize solely 3D printing technology for the wings, body, and all other structures. The only off-the-shelf components can be the motor and electronics, as well as mechanical devices such as hinges.

Using Predictive Analytics To Reduce Small Business Cost Estimation Error, Diana Solt

Journal of Applied Packaging Research

Small and medium packaging companies generally employ the use of custom-developed quoting programs to bid goods and services. Custom bid programs (e.g. Excel) are used to capture the company-specific costs of production. The inputs of variable costs, such as machine rate and scrap rate, are critical to get correct; however, companies often rely on educated guesses and industry expertise to quote packaging products to end-users. Due to the guesswork involved there can be a financial difference between the quoted costs and actual costs. This variance is often the cause of significant lost dollars. Price, if not determined correctly, could negatively …

Thermal Characterization Of 3d Printing Materials For Increasing Insulation Potential And Practicality, Jackson H. Minnick

Mechanical Engineering Undergraduate Honors Theses

This study served as an exploration into the possible existence of a correlation between the infill lattice structure of a 3D printed wall section and the thermal performance of that sample as characterized by thermal conductivity measured in units of Watts per meter Kelvin. With the continual increase in the practicality, fidelity, and applicable fields of additive manufacturing, namely FDM 3D printing, research on specific print characteristics and their effects on the material and thermal characteristics of the part in question is steadily becoming more commonplace. Although the thermal conductivity of 3D printed wall sections as a function of infill …

Ultrafast Laser Surface Structuring For Wettability Control On Copper, Akshay Arvind Nagvenkar

All Theses

Wettability is a crucial surface property influencing various phenomena, including heat transfer, cell adhesion, and corrosion. Engineering devices can achieve superior performance by precisely manipulating surface wettability. As a result, extensive research has focused on developing surfaces that exhibit either extreme water attraction (superhydrophilic) or strong water repellency (superhydrophobic). Tailoring surface wettability paves the way for numerous applications, such as drag reduction in marine vessels, controlled drug delivery, efficient water collection, advanced liquid transport systems, oil-water separation, anti-corrosion coatings, friction reduction, and self-cleaning materials. Ultrafast laser surface structuring is a promising approach for engineering multifunctional surfaces, effectively modifying material properties …

Development Of Planetary Drive System For Formula Sae Electric Race Car, Brian Wong, Bradley Maruoka, Joshua Charles Fine, Madison Kai

Mechanical Engineering

Hub motors are compact electric motors mounted directly on each outboard wheel hub. Utilized in Formula SAE and Formula Student vehicles, this configuration offers several advantages over traditional drivetrains, including packaging optimization within the chassis, vehicle traction, and improved efficiency. Although hub motors are not yet common in 4WD vehicles, they are being explored for use in EVs and may become more common in the future. Every year, Cal Poly Racing FSAE designs and builds a formula-style race car. To improve drivetrain performance, the team is investigating the achievability of a hub motor 4WD drivetrain, requiring extensive research, development, and …

Biobased Acrylate Composites With Enhanced Strength For Additive Manufacturing, Nicole Wagner, Joseph Mcwherter

Engineering Faculty Articles and Research

With the expanding use of polymers in additive manufacturing, sustainable resins for use in vat photopolymerization are required to reduce their environmental impact. One promising approach to achieve this is to incorporate biobased fillers that replace the acrylates in photopolymer resins as ‘green’ alternatives. In this study, photopolymer composites consisting of a methacrylate resin with varying calcium carbonate powder content between 0 and 50 wt.% were investigated. A digital light processing technique was used to fabricate tensile test specimens for mechanical testing. Good printability, dimensional accuracy, and good interlayer adhesion were observed for composite resin formulations that incorporated calcium carbonate …

Design And Development Of A Rapid Tensile Quench Rig, Tyler Jewell, Justin Naylor

Williams Honors College, Honors Research Projects

This report outlines the design process and implantation of a tensile quenching rig that incorporated forced convection and a frequency generator. When any metal is quenched, a vapor barrier forms around it. When this happens, it limits the heat flux that may occur until the barrier turns into just nucleate boiling. The vapor barrier acts as an insulator and causes the heat flux to fluctuate, causing uneven hardening which would limit the use of some materials. To combat this effect, we are trying to use forced convection, and something new, which is adding high frequency waves into the quenching process. …

Effect Of Build Orientation On Tensile Properties And Fractography Of Additive Manufactured Inconel 718 Alloy, Ajay Kumar Maurya, Amit Kumar, Swarnambuj Suman

ASEAN Journal on Science and Technology for Development

The additive manufacturing (AM) technique “Direct Metal Laser Sintering (DMLS)” is used to create 3D objects directly from 3D design data. A lightweight and complexity-free part without any expensive tooling can be fabricated easily using this method, but it is still challenging to achieve the desired mechanical strength from AM parts, as the mechanical properties of AM-produced parts vary with orientation, scan strategy, and process parameters. Inconel 718 alloy is most commonly utilized in the aerospace and automotive industries, because of its high resistance to corrosion and excellent mechanical qualities. This work presents a study to investigate the orientation-based mechanical …

Pulsed Arc Additive Manufacturing Of A Functionally Graded Er2209 Duplex Stainless Steel And Hsla-100 Structure: Morphology, Characterization, And Mechanical Performance, Stevens G. Hill Jr

College of Graduate Studies: Theses & Dissertations

Wire arc additive manufacturing is a process well suited to the efficient production of large structures. Duplex stainless steel exhibits high corrosion resistance and good strength which can be highly beneficial for industrial use. However, its use is limited due to its cost and complexity in controlling microstructure to achieve desired properties. In many cases, it can be highly beneficial to manufacture a component which uses specialty steel grades such as duplex stainless steel only where necessary, and utilizes more affordable, commonly available steels for reinforcement or bulk structural support. A functionally graded material satisfies these requirements by providing a …

Enhancing The Mechanical Properties Of Sla 3d-Printed Bio-Resin From Linseed Oil Using Cellulose And Lignin Biopolymers, Chukwunonso A. Ikedionu

College of Graduate Studies: Theses & Dissertations

Abstract

This research explores the development of bio resin from linseed oil by the process of epoxidation and acrylation to produce acrylated epoxidized linseed oil (AELO). Lignin and cellulose biopolymers were added as reinforcement at varying weight fractions of 1 wt.%, 2.5 wt.%, and 5 wt.%, and their mechanical performance was compared against pure AELO. The formulations were printed using an Elegoo SLA 3D printer to create standardized test specimens like tensile bars, compression cylinders, and hardness blocks, which were all prepared according to the ASTM testing standard.

The results indicate that reinforcement effects depend on both filler type and …

Fabrication And Performance Of Scalable Bio-Engineered Porous Layers For Efficient Co2 Capture, Mary Sharon Rose Bondugula

Theses and Dissertations

This dissertation addresses the critical challenge of mitigating climate change by advancing CO2 capture technologies. As global CO2 emissions continue to rise, effective methods for capturing and separating CO2 from industrial processes are essential to combat climate change. Existing CO2 capture systems, such as Pressure Swing Adsorption (PSA) and Temperature Swing Adsorption (TSA), often rely on packed bed designs that face limitations, including poor heat and mass transfer, slow gas diffusion, and low thermal conductivity, reducing their efficiency. To overcome these challenges, this dissertation explores innovative solutions by developing advanced adsorbent coatings and scalable bed configurations.

This research begins by …

Mechanical Properties Of Polymer Matrix Nanocomposites Reinforced With Varying Carbon Nanotube Geometries, Ethan Gaigalas, Zoe Kelemen

College of Engineering Summer Undergraduate Research Program

This study serves as part of an introduction to nanocomposite research at California Polytechnic State University, San Luis Obispo, and attempts to form an observational comparison between the performance of various CNT-Epoxy nanocomposites under drop weight testing. As a continuation of research on CNT-Epoxy nanocomposites, this study specifies three geometries of Multi-walled carbon nanotubes: straight (MWSCNTs), helical (MWHCNTs), and OH-functionalized straight (FMWSCNTs); and it compares their impact resistances to neat epoxy samples. Based on the total number of failed samples under a normalized impact energy of 0.335J/mm, it is observed that FMWSCNTs increase the impact resistance of Epoxy panels at …

Predicting The Ductility Of Tungsten Based Bcc Refractory High Entropy Alloys: A Computational Science Driven Study, Akshay Korpe

All Theses

Bcc refractory high entropy alloys (HEAs) are a relatively new category of metallic alloys that promise excellent irradiation resistance and strength retention at high temperatures but exhibit brittle behavior at room temperatures limiting their formability. Understanding the deformation mechanisms and predicting their ductility at room temperature is a topic of interest in contemporary research.

In this work, multiple independent ductility criteria for quantifying the ductility of these HEAs were studied, calculated and compared using Density Functional Theory (DFT) calculations and continuum mechanics frameworks. These ductility parameters were calculated for various W-Ta-Cr-V alloys and the trends were analyzed for each criteria …

Development, 3d Printing, And Sintering Of Aluminum-Magnesium Alloy Pastes For In-Space Manufacturing Applications, Fatou Ndiaye

Electronic Theses and Dissertations

This study explores the additive manufacturing process of paste printing, sintering, and de-binding for fabricating aluminum-magnesium alloy components. The paste formulation involved combining aluminum powder with varying magnesium concentrations, utilizing acrylic polyol, solvent, and plasticizer to create a homogeneous mixture. Printing parameters were optimized to ensure continuous pressure for improved extrusion. Sintering conditions involved incremental temperature increases with nitrogen flow to remove solvents. Density measurements, tensile tests, and shrinkage calculations were conducted to assess part quality post-sintering. The study revealed significant improvements in part quality with 5 wt.% magnesium incorporation within aluminum, although density and tensile strength fell short of …

A Study On High-Frequency Bending Fatigue, Microhardness, Tensile Strength, And Microstructure Of Parts Made Using Atomic Diffusion Additive Manufacturing (Adam) And Additive Friction Stir Deposition (Afsd), Hamed Ghadimi

LSU Doctoral Dissertations

This dissertation reports the findings of several studies on the mechanical and microstructural properties of parts made using atomic diffusion additive manufacturing (ADAM) and additive friction stir deposition (AFSD). The design of a small-sized bending-fatigue test specimen for an ultrasonic fatigue testing system is reported in Chapter 1. The design was optimized based on the finite element analysis and analytical solution. The stress–life (S–N) curve is obtained for Inconel alloy 718. Chapter 2 presents the findings of ultrasonic bending-fatigue and tensile tests carried out on the ADAM test specimens. The S-N curves were created in the very high-cycle fatigue regime. …

Thermomechanical Process Simulation And Quantification Of Nanoscale Precipitation Influencing Ductility And Strength During Alloy Processing, Alyssa Stubbers

Theses and Dissertations--Chemical and Materials Engineering

Experimental process simulation and quantification of microstructure development during processing are challenging due to limitations with machinery temperature capability, inadequate resolution and sampling volume of currently available characterization techniques, and difficulty characterizing material microstructures as close to processing-relevant conditions as possible. This dissertation addresses how process simulation can be performed using Gleeble thermomechanical technologies and how microstructure development during these processing simulations can be quantified both in-situ and ex-situ.

The first portion of this dissertation demonstrates how Gleeble technologies can be applied to simulate complex material processing conditions in order to produce process-property profiles that can be used to inform …

Experimental Investigation Of Liquid Metal Embrittlement In Hot-Dip Galvanized Structural Steel, Amelia Mcnamee

College of Graduate Studies: Theses & Dissertations

This research investigated the liquid metal embrittlement (LME) of hot-dipped galvanized structural steel. The relationship between stress and failure time was analyzed to evaluate the potential presence of a critical stress threshold beyond which LME may occur. A testing apparatus to induce axial stress was designed and assembled in-house. A36 low carbon steel was tested in this study. Different deadweight loadings were applied to the testing sample along the axial direction. The test temperature was maintained by a programmable furnace while the sample gauge section was submerged in a molten zinc bath. Failure time and total displacement of the steel …

Laser Deposition Additive Manufacturing Of Multi-Material And Metal-Ceramic Composite Structures, Manikanta Grandhi

Graduate Theses, Dissertations, and Problem Reports (ETD)

The increasing performance requirements of modern industrial systems, coupled with the imperative for decarbonization, necessitate a fundamental rethinking of metallic component design and manufacturing. Traditional materials, with their inherent limitations in property optimization, susceptibility to degradation, and weight constraints, are proving insufficient. Multi-material joining offers a potential solution, enabling designers to strategically integrate diverse materials with specific, tailored properties into single component. Functionally graded materials (FGMs) and oxide dispersion strengthened (ODS) materials are prime examples of this approach, delivering substantial improvements in wear resistance, thermal regulation, high-temperature resilience, and overall weight efficiency. However, conventional manufacturing approaches further exacerbate the limitations …

Fabrication & Characterization Of Hybrid Piezoelectric/Triboelectric Nanocomposite Nanogenerators Via Fusion Deposition Modeling, Khaled El Toukhy

Theses and Dissertations

This thesis aims to discuss the potential of using piezoelectric and triboelectric nanogenerators (PTENGs) for energy harvesting, particularly in the sportswear industry. PTENG's main advantage is that it offers good flexibility making it suitable for high-strain applications. The piezoelectric effect is induced by embedding piezoelectric nanofillers into one of the two triboelectric layers. PTENGs can generate both piezoelectric and triboelectric signals when strained resulting in an enhanced output compared to regular piezoelectric nanogenerators (PENGs) and triboelectric nanogenerators (TENGs). TPU was adopted as the matrix for PTENGs advantageous due to their flexibility, low electrical resistivity, and compatibility with additive manufacturing techniques. …

Temperature Gradient Effect On Solid-Liqid Interface Properties Of Al-Cu Alloy: A Molecular Dynamics Study, Prashant Kumar Jha

All Theses

Aluminum-copper (Al-Cu) alloys are widely used in the aerospace industry due to their favorable strength-to-weight ratio, good fatigue resistance, and corrosion resistance. These properties make Al-Cu alloys an excellent choice for aircraft structural components that require high strength and low weight. Additive manufacturing (AM), also known as 3D printing, has emerged as a promising processing method for Al-Cu alloys in aerospace manufacturing. AM enables the production of lightweight optimized geometries difficult to manufacture through conventional subtractive methods. AM also reduces material waste by only depositing material where needed in the part geometry. The rapid solidification conditions in AM processes motivate …

Optimizing Mn-Al Permanent Magnet Performance Through Control Of The Phase Transformation, Ternary Element Addition, And Advanced Processing, Thomas R. Keller

Dartmouth College Ph.D Dissertations

The growing need for electrical power in machines and vehicles brings with it a growing need for critical materials. The current high-performance permanent magnets (PMs) based on rare-earth (RE) elements Nd and Sm cannot escape the problem of raw material cost, geographic scarcity in the earth’s crust, and lack of circular global supply chains. This poses a problem of industrial ecology: can PMs be made from inexpensive, more abundant materials while still meeting sufficient performance criteria? PMs based on the magnetic τ phase of Mn-Al offer a possible alternative to REPMs. However, years of innovation have not yet achieved real-world …

Optimization Of Alti Pld Coating By Increasing Ti Content, N2 And Annealing Which Used For Skd61 Pins In Aluminum Die Casting, Rusman Kosasih, Maria Margaretha Suliyanti Prof, Dedi Priadi, Wisnu Usni

Journal of Materials Exploration and Findings

The Alumunium Titanium Nitrogen (AlTiN) coating is known as one of the best coating materials for protective coating, while Pulsed Laser Deposition (PLD) is a laser coating process used for electric layer and superconductor applications, producing thin films up to 20 µm in thickness. The combination of these two matters has already been researched and is still in progress. One major challenge in the aluminium casting industry is to minimize the damage caused to tool steel pins made from SKD61, when aluminium material sticks to the pin, and halting production. Therefore, research on effective coatings for tool steels and testing …

3d Printed Aircraft, Matthew Nagy, Charles D'Amico, Alexis Salgado Medina

Mechanical Engineering

This project is to design, build, and test a 3D-printable aircraft. The goal is to create a final design that will be able to fly for the longest duration possible, around 20 seconds. To determine the correct preliminary design and manufacturing process for a 3D printed RC aircraft, an analysis of multiple design options and manufacturing materials was performed. This allowed for a variety of choices for aircraft type, airfoil design, structure, among other topics to be narrowed down to the most promising option. It has been found that the aircraft will follow a design similar to industry motor-gliders, with …